Fujitsu XG Series Operation & User’s Manual

Text of Fujitsu XG Series User Guide:

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference Device Information Settings 321 5.15.8.35 serverinfo sntp Function Set the SNTP server. Available Model XG0224 / XG0448 / XG2600 Syntax serverinfo sntp ip <mode> Options <mode> • on Enable the SNTP server function. • off Disable the SNTP server function. Use Mode Configuration mode (admin class) Explanation Set whether or not to enable the SNTP server function. Default It is assumed that the SNTP server function is enabled. 5.15

• XG Series User's Guide Chapter 5 Command Reference Ethernet Counter, Log, Statistics, and Status Display and Clear Operation Commands 393 (Continued) [Output Statistics] Octets : 0 bits/sec : 0 Frames : 0 frames/sec : 0 Unicast : 0 Multicast : 0 frames/sec : 0 Broadcast

• Fujitsu XG Series, XG Series User's Guide Chapter 4 Switch Functions and their Configuration Quality of Service (QoS) 76 4.7 Quality of Service (QoS) The device provides Quality of Service (QoS) that is based on the IEEE802.1p standard. The device QoS determines the priority of frames at the ingress side using VLAN tag (including priority tag) or a port's default priority. Their priorities are mapped to 8 output queues. The queues are processed in the order of the QoS priority precedence. The device priorities available are: • Default p

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference Port Information Settings 129 5.1.4.2 ether lldp info Function Set LLDP information which is sent Available Model XG0224 / XG0448 / XG2600 Syntax ether <number> lldp info port-description <mode> ether <number> lldp info system-name <mode> ether <number> lldp info system-description <mode> ether <number> lldp info system-capabilities <mode> ether <number> lldp info management-address <mode> ether <number> lldp info port-vlan-id <mode> ether <number> lldp info port-and-protocol-vla

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference IGMP Snooping Information Settings 228 5.10 IGMP Snooping Information Settings This section explains about IGMP snooping information settings. 5.10.1 IGMP Snooping Information This section explains about the commands related to IGMP snooping information. 5.10.1.1 igmpsnoop use Function Set the IGMP snooping function. Available Model XG0224 / XG0448 / XG2600 Syntax igmpsnoop use <mode> Options <mode> Specify the IGMP snooping mode. • on Enable IGMP snooping. • off Disable IGMP snooping. Use Mode Configuration mode (admin class) Explanation Specify the IGMP snooping mo

• Fujitsu XG Series, XG Series User's Guide Appendix List of MIBs 597 ifStack Group ifMIB Group B.1.14 radiusMIB Group radiusAuthClient Group 14 ifHCOutMulticastPkts ifXEntry.12 RO 15 ifHCOutBroadcastPkts ifXEntry.13 RO 16 ifLinkUpDownTrapEnable ifXEntry.14 RO 17 ifHighSpeed ifXEntry.15 RO 18 ifPromiscuousMode ifXEntry.16 RO 19 ifConnectorPresent ifXEntry.17 RO 20 ifAlias ifXEntry.18 RO 21 ifCounterDiscontinuityTime ifXEntry.19 RO No. Name Object identifier MIB ACCESS 1 ifStackTable ifMIBObjects.2 – 2 ifStackEntry ifStackTable.1 – 3 ifStackHigherLayer ifStackEntry.1

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference Login banner Settings 328 5.16 Login banner Settings This section explains about Login banner settings. 5.16.1 Login banner Information This section explains about the commands related to Login banner information. 5.16.1.1 login banner telnet Function Turn on or off the telnet login banner. Available Model XG0224 / XG0448 / XG2600 Syntax login banner telnet <mode> Options <mode> Specify the desired mode. • on Specify "on"

• Fujitsu XG Series, XG Series User’s Guide Contents 7 5.5.6 Management LAN port IPv6 Related Information ................................................................................ 211 5.5.6.1 oob ip6 use ............................................................................................................................. 211 5.5.6.2 oob ip6 ifid ............................................................................................................................. 211 5.5.6.3 oob ip6 address ................................................................................................................

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference System Operations and Display Commands 363 (Continued) (To be continued) User Stack: +0 +4 +8 +C +0 +4 +8 +C 04ae9f60 04aea1d0 00886d58 04ae9fb8 04ae9fa0 ......mX........ 04ae9f70 00c6fcbb fea4cebb d8c4eab7 c1bcb0a1 ................ 04ae9f80 a2c9bdbc a8b7c1bc b0a4f2a5 aca5a4a5 ................ 04ae9f90 c9a5e9a5 a4a5f3a4 cba4a2a4 efa4bba4 ................

• XG Series User's Guide Index 608 Index Symbols ! .............................................................................. 336 Number 10/100/1000BASE-T Port Specifications ................ 28 A aaa name ................................................................. 243 aaa radius auth message-authenticator ................... 249 aaa radius auth source

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference Mode and Terminal Operation Commands 339 If information is displayed, the following prompt will appear. If it cannot be displayed backward, the following prompt will appear. Description: a: Top line number on screen b: Bottom line number on screen c: Total number of lines d: Number of displayed bytes e: Total number of bytes f: Ratio of total number of bytes to number of displayed bytes (d / e x 100) When a help is displayed, the prompt below will appear following the help. Press the [RETURN] key. Pressing [CTRL+C] will halt the display of command output. MORE: help (press RETURN) Caution When the allowable number of screen lines

• Chapter 6 Managing the Device This chapter describes the Managing the Device. 6.1 Verifying the Device Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548 6.1.1 Verifying Hardware Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548 6.1.2

• Fujitsu XG Series, XG Series User's Guide Chapter 4 Switch Functions and their Configuration Link Aggregation 69 4.4.2 Frame Distribution Methods in Link Aggregation How frames are distributed across physical ports that make up an aggregation group are determined by the contents of a frame (source and destination MAC addresses). There are 6 ways to specify how frames are distributed: • Frame distribution based on destination MAC address (da-mac) The destination port is determined based on the destination MAC address of the frames. • Frame distribution based on source MAC address (sa-mac) The destination port is determined based on the sour

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference LACP Counter, Log, Statistics, and Status Display and Clear Operation Commands 420 1) Port number 2) Indicates that the information display at the right side is for this device (Actor) or the remote device (Partner). 3) Indicates that the LACP mode is active or passive. The passive is displayed if the valid LACP remote system information has not been obtained. 4) Indicates the LACP state as follows. T (LACP_Timeout): The LACPDU's receive timeout has been set to Short Timeout (3 seconds). If not shown, the Long Timeout (90 seconds) has been set. A (Aggregation):

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference LAN Information Settings 193 Explanation Set DSCP value rewriting conditions. Rewrite the DSCP value of a packet, which has satisfied conditions, to the specified DSCP value. Caution Note 1. If none of "acl ip" definition exist on the access control list which has been specified by <acl> or if the access control list specified by <acl> does not exist, the packets are not filtered. [XG2600] Note 2. This command is unavailable if the allowabl

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference VLAN Information Settings 174 If "dscp" is selected in <action>: - <dscp_value> Set the replaced "dscp" value with a decimal value from 0 to 63. If "tos" is selected in <action>: - <tos_value> Set the replaced "ip precedence" value with a decimal value from 0 to 7. -cos Replace the "ip precedence" value with the "cos" value. If "queue" is selected in <action>: - <queue_value> Specify a queue number

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference SNMP Statistics Display and Clear Operation Commands 518 4) Total number of SNMP received messages of the unused community 5) Total number of received messages that indicate the operations not allowed in the community 6) Total number of received messages with ASN.1 errors 7) Total number of receive PDU packets with the tooBig error status 8) Total number of receive PDU packets with the noSuchName error status 9) Total number of receive PDU packets with the badValue error status 10) Total number of receive PDU packets wit

• Fujitsu XG Series, XG Series User's Guide Chapter 2 Using the CLI Using the CLI 45 Three times Command forms are displayed. In operation mode, simplified command forms are displayed. In configuration mode, when the configuration hierarchy function is disabled, simplified command forms are displayed. In configuration mode, when the configuration hierarchy function is enabled and you are at the top hierarchy level, simplified command forms are displayed. In configuration mode, when the configuration hierarchy function is enabled and you are not at the top hierarchy, command forms for the current hierarchy level and simplified command forms are displayed. Four times Returns to the operatio

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference Configuration Display, Delete and Operation Commands 375 5.19.3.3 commit Function Commit (or dynamically activate) the configuration. Available Model XG0224 / XG0448 / XG2600 Syntax commit Options N/A Use Mode Configuration mode (admin class) Explanation Apply the configuration that was set or changed with the configuration command, without device restart. Caution Changing the configuration may cause the communication interface to come down once in order to apply address information in the device, resulting in a communication interrupt. Message Since unallowable configuration was added or changed, it cannot be applied.

• Fujitsu XG Series, XG Series User's Guide Chapter 5 Command Reference LAN Information Settings 187 Explanation Set the IP filter for the LAN interface. The IP filter is used to transmit or reject packets that have matched the address, protocol, TOS or DSCP value, port number, ICMP TYPE, and ICMP CODE specified in ACL. Checking whether the conditions are satisfied or not according to the set priority, if a packet that has satisfied those conditions is found, it is filtered, and the subsequent setting will be ignored. A packet that has not satisfied any conditions will be

• XG Series User's Guide Chapter 5 Command Reference Ethernet Counter, Log, Statistics, and Status Display and Clear Operation Commands 388 linkaggregation: Indicates that the port is used as a link aggregation port. This parameter also indicates the number of the link aggregation group that the port belongs to. "*linkaggregation" is displayed when the link

• Fujitsu XG Series, XG Series User's Guide Chapter 4 Switch Functions and their Configuration VLAN 75 4.6.2 Tag-Based (IEEE802.1Q) VLAN Tag-based VLAN is a method of configuring VLANs so that the frame forwarding decision is based on a tag in the MAC header identifying the VLAN membership. 4 bytes of additional data in the header, called a VLAN tag, identifies the VLAN frame ownership. Using a VLAN tag enables configuring a single physical link that shares multiple VLANs. The device’s tag-based VLAN function is based on the IEEE 802.1Q standard. The fo

Related Products and Documents (Computer Hardware):

Comparable Devices:

Similar Resources:

• ekwb EK-FB EVGA CLASSIFIED 4-SLI (2 pages)  Installation and mounting manuals for EK-FB EVGA CLASSIFIED 4-SLI water block:This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use …

• Snom 360 (2 pages) snom 360 Quick User Guide. 3/5/09 1 snom 360 Quick User Guide Basic Phone Features For detailed information please consult the Star2Star Phone and Features Guide, available for view/download via the Star2Star Web Portal at: https://portal.star2star.com/ MAKING A CALL Using the handset: - Pick up the handset, the yellow line i …

• Exsys EX-41150 (2 pages) 6 5 EXEXEX---411504115041150 EnglishEnglishEnglish EXEXEX---411504115041150 EnglishEnglishEnglish Windows Server 200x: After starting Windows it recognizes a new “PCI Controller“ and open the hardware assistant. Please choose manual installation and put the driver CD into your CD-Rom drive. Now enter the Path "D:\IO\NETMOS\98XX" and …

• Apple Mac Pro RAID Card and Battery (6 pages) 073-1251 Rev. A 1© 2009 Apple Inc. All rights reserved. Mac ProFirst StepsShut down computer.1 2 Wait 10 minutes.Warning: Parts inside computer can be very hot. Allow computer to cool down before continuing.Unplug all external 3 cables except power cord.Touch metal PCI cover 4 on back of computer.Unplug power cord.5 Opening the ComputerHold side acce …

• Analog Devices ADSP-BF535 Blackfin (1022 pages) aADSP-BF535 Blackfin® ProcessorHardware ReferenceRevision 3.3, February 2013Part Number82-000410-13Analog Devices, Inc.One Technology WayNorwood, Mass. 02062-9106 …

• Dynex DX-PCCNG50 (13 pages) USER GUIDEPCI-Express Gigabit Ethernet Adapter CardDX-PCCNG50Before using your new product, please read these instructions to prevent any damage.DX-PCCNG50 14-1421_MAN_V1_ENG.fm Page 1 Tuesday, January 13, 2015 10:31 AM …

Comments, Questions and Opinions: