Manualios.com

Fujitsu ESPRIMO E5635 Operating Manual

Fujitsu ESPRIMO E5635 Manual Online:

4.35, 1025 votes
Fujitsu ESPRIMO E5635 User Manual
Fujitsu ESPRIMO E5635 User Guide
Fujitsu ESPRIMO E5635 Online Manual

Text of Fujitsu ESPRIMO E5635 User Guide:

  • System expansions 48 Fujitsu Technology Solutions Removing board from bracket ► Disconnect the cables connected to the board. ► Press on the retaining bracket in the direction of the arrow and fold it down. ► Pull the board out of the slot of the board bracket in the direction of the arrow.

  • Fujitsu ESPRIMO E5635, Copyright © Fujitsu Technology Solutions 2009 2009/11 Published by Fujitsu Technology Solutions GmbH Mies-van-der-Rohe-Straße 8 80807 München, Germany Contact http://ts.fujitsu.com/support All rights reserved, including intellectual property rights. Technical data subject to modications and delivery subject to availability. Any liability that the data and illustrations are complete, actual or correct is excluded. Designations may be trademarks and/or copyrights of the respective manufacturer, the use of wh

  • Fujitsu ESPRIMO E5635, System expansions 72 Fujitsu Technology Solutions Removing SmartCard reader and/or WLAN module ► Open the casing (see "Opening the casing"). ► Remove the cross-piece (see " Removing the cross-piece”). ► Fold up the drive cage (see " Folding up the drive cage"). 1 1 ► Remove the screws (1). ► Disconnect the cables. ► Fold down the drive cage (see " Folding down the drive cage"). ► Pull the holder out of the casing in direction of the arrow. ► Replace the cross piece (see " Installing the cross-piece"). ! If you remove the SmartCard reader and/or the WLAN mo

  • Fujitsu ESPRIMO E5635, Important notes 4 Fujitsu Technology Solutions Energy saving, disposal and recycling Information on these topics can be found on the "Drivers & Utilities" CD or on our website http://ts.fujitsu.com. CE marking The shipped version of this device complies with the requirements of the EC Guidelines 2004/108/EC "Electromagnetic compatibility" and 2006/95/EC "Low voltage directive". CE marking for devices with radio component This equipment complies with the requirements of Directive 1999/5/EC of the European Parliament and Commission from 9 March, 1999 governing Radio and Telecommunications Equipment and mut

  • Fujitsu ESPRIMO E5635, Contents Fujitsu Technology Solutions Error messages on the screen............................................................................................................35 Restoring the hard disk contents ........................................................................................................36 Tips 36 System expansions...........................................................................................................................37 Information about boards ............................................................................................................37 Opening th

  • Fujitsu ESPRIMO E5635, System expansions Fujitsu Technology Solutions 57 Installing plastic drive cover Depending on the drive, you must reinstall the plastic drive cover. Depending on the type of device, this is either included with the equipment or can be purchased as an accessory. ► Press the plastic drive cover from the inside into the front panel in the direction of the arrow until you feel it latch into place. ► Close the casing (see " Closing the casing").

  • Fujitsu ESPRIMO E5635, Troubleshooting and tips Fujitsu Technology Solutions 35 No mouse pointer displayed on the screen ► Shut down the operating system properly. ► Switch off the device. ► Check that the mouse cable is properly connected to the system unit. If you use an adapter or extension lead with the mouse cable, check the connections. ► Make sure that only one mouse is connected. ► Switch the device on. The floppy disk cannot be read or written ► Check that the write protection of the floppy disk or the floppy disk dri

  • Fujitsu ESPRIMO E5635, Preparing for use 14 Fujitsu Technology Solutions Connecting external devices to the parallel or serial port If your device has parallel and serial ports, you can connect external devices to these ports (such as a printer or modem). ► Connect the data cable to the external device. ► Depending on the device, connect the data cable to the parallel port or the serial port . For an exact description of how to connect external devices to the corresponding port, please see the external device documentation. i Port settings You can change the port settings (e.g. address, interrupt) in the BIOS Setup. Device drivers The devices connected to t

  • System expansions Fujitsu Technology Solutions 49 ► Push the slot cover into the slot in the direction of the arrow. Ensure that the point of the slot cover engages on the outside of the board bracket. ► Fold up the retaining bracket so that it engages. ! For cooling, protection against fire, and in order to comply with EMC (electromagnetic

  • Fujitsu ESPRIMO E5635, System expansions 38 Fujitsu Technology Solutions Opening the casing ► Switch off the device. The device must not be in the energy-saving mode! ! Please take note of the safety information in the " Important notes" chapter. Pull the power plug out of the mains outlet! ► Remove all cables from the casing. ► Place the casing in a convenient working position. On devices with main power switch ► Turn the key in the direction of the arrow to unlock the casing (see " Mechanical casing lock (optional)“). a 2 3 1 1 2 3 1 ► Press the two locking catches (1), hold them pressed and slide the upper casing in the direction

  • System expansions Fujitsu Technology Solutions 59 Installing a drive ► Take the new drive out of its packaging. ► Adjust the required settings on the drive (if necessary, on already-installed drives as well). ► Press the EasyChange rails into the provided holes. ► Push the accessible drive into the casing until the EasyChange rails engage. ► Plug the data and th

  • Fujitsu ESPRIMO E5635, System expansions Fujitsu Technology Solutions 51 Installing and removing optional ports An additional port (serial or parallel) can be installed in a rear slot cover plate like a board. For an exact description of how to connect external devices to ports, refer to the documentation for the external device. Installing an additional serial port ► Open the casing (see "Opening the casing"). 2 5 4 3 1 ► Press on the locking lever in the direction of the arrow (1), unhook it and swing it up in the direction of the arrow (2). ► Remove the rear slot cover plate from the slot (3). ! Do not dispose of the cover pl

  • Fujitsu Technology Solutions Contents Your ESPRIMO E... ............................................................................................................................. 1 Notational conventions ......................................................................................................................... 2 Important notes ..............

  • Fujitsu ESPRIMO E5635, System expansions Fujitsu Technology Solutions 73 Extensions to the mainboard The description of how to upgrade the main memory and/or processor is contained in the manual for the mainboard. ► Open the casing (see " Opening the casing"). ► Fold up the drive cage (see " Folding up the drive cage"). Upgrading main memory ► Upgrade the memory according to the description in the manual for the mainboard. ► Fold down the drive cage (see " Folding down the drive cage").

  • Fujitsu ESPRIMO E5635, Preparing for use Fujitsu Technology Solutions 9 Vertical operating position Proceed as follows to operate the device in the vertical operating position: ► If necessary, disconnect the cables. ► Position the casing vertically so that the ON/OFF switch is located at the bottom. ► Pull off the foil from the rubber / plastic feet that you will find in the accessories package. 57 mm 6 mm 37 mm 1 1 1 1 ► Glue the rubber/plastic feet (1) on the casing wall. In order to ensure that the device is stable, the position of the rubber/plastic feet must correspond to the given dimensions. ► Place the unit on the rubbe

  • Fujitsu ESPRIMO E5635, Preparing for use Fujitsu Technology Solutions 21 Switching on the device (without the main power switch) ► Press the ON/OFF switch on the front of the device. The power-on indicator lights green and the device starts up. Installing the software ► During installation, follow the on-screen instructions. ► Consult the manual for the operating system if there is anything unclear about the requested input data. i You will find further information about the system, drivers, utilities and updates on the "Drivers & Utilities" CD.

  • Fujitsu ESPRIMO E5635, System expansions 40 Fujitsu Technology Solutions Installing and removing the cross-piece ► Open the casing (see "Opening the casing"). Removing the cross-piece a ► Lift off the cross-piece upward at the marking (a) in the direction of the arrow. Installing the cross-piece a ► Insert the cross-piece into its guide lugs (a) on the front of the casing at an angle from above. ► Press the cross-piece downward in the direction of the arrow until it rests on the casing and engages. ► Close the casing (see

  • Fujitsu ESPRIMO E5635, Operation 24 Fujitsu Technology Solutions Switching off the device ► Shut down the operating system properly. For Windows: select Shut Down from the Start menu. ► If the operating system does not automatically switch the device into an energy-saving mode or switch it off, press the ON/OFF switch. The device then consumes a minimum amount of energy. ! The ON/OFF switch does not disconnect the device from the mains voltage. To completely disconnect the mains voltage, remove the power plug from the socket. ► If necessary, switch the monitor off (see the operating manual for the monitor).

  • Fujitsu ESPRIMO E5635, Troubleshooting and tips 34 Fujitsu Technology Solutions Wrong monitor has been set under Window XP ► Restart the device. ► Press F8 while the system is booting. Either the Windows Advanced Start Options menu or the menu for selecting the operating system appears. ► If the menu for selecting the operating system appears, press F8 . ► Select Safe Mode or Safe Mode with Network. ► Set the correct values for the attached monitor as described in the operating manual of the monitor by selecting Start - Settings - Control Panel - Display and then the Appearance, Themes,

  • Preparing for use 12 Fujitsu Technology Solutions Connecting the monitor i Depending on the device configuration level, the monitor ports of the mainboard (1) may be covered and without function. In this case, only use the external monitor ports of the display adapters in one of the module slots (2). 4 3 1 2 1 = Monitor ports of the mainboard 2 = Ext

  • Fujitsu ESPRIMO E5635, System expansions 46 Fujitsu Technology Solutions Installing board in bracket ► Make the required settings for the board. ! Do not dispose of the slot cover. For cooling, protection against fire and in order to comply with EMC regulations, you must refit the slot cover if you remove the board. ► Press on the retaining bracket in the direction of the arrow and fold it down. ► Pull the slot cover out of the slot in the direction of the arrow.

  • Fujitsu ESPRIMO E5635, System expansions 66 Fujitsu Technology Solutions 2 1 3 ► Fold down the power supply in the direction of the arrow (1) until the power supply engages. ► Press on the locking lug (2) of the drive cage and then fold the drive cage with light pressure in the direction of the arrow (3) until the lever engages. Make sure that the cables are not kinked or pinched. ► Connect the power supply connector. ► Replace the cross piece (see " Installing the cross-piece"). ► Close the casing (see " Closing the casing"). i It may be necessary to modify the entry for the drive in the BIOS Setup.

  • Fujitsu ESPRIMO E5635, Preparing for use 8 Fujitsu Technology Solutions Setting up the device ! When installing your device, give consideration to the safety notes in the "Safety" manual. Only install the device in the operating positions for which it is intended. We recommend that you place your device on a surface with good anti-slip qualities. In view of the multitude of different finishes and varnishes used on furniture, it is possible that the rubber / plastic feet will mark the surface they stand on. Do not expose the device to extreme environmental conditions (see " Technical data"). Protect the device from dust, humidity, and heat. When installing the workstati

  • Fujitsu ESPRIMO E5635, Preparing for use Fujitsu Technology Solutions 11 Ports provided by the device The connections are located on the front and back of the device. The ports available on your device depend on the configuration level you have selected. The standard ports are marked with the symbols shown below (or similar). Exact details of the position of the ports are supplied in the manuals for the boards. Keyboard port, purple PS/2 mouse port, green 1 Serial port 1, teal or turquoise 2 Serial port 2, teal or turquoise Monitor port, blue Parall

  • Fujitsu ESPRIMO E5635, System expansions Fujitsu Technology Solutions 55 Installing and removing drives In the standard model the device may be equipped with the following drives: ● one accessible 3 ½ inch drive (floppy drive) ● one non-accessible 3 1/2 inch drive (hard disk) ● one accessible 5 ¼ inch drive (e.g. DVD or CD ROM drive) or: ● two non-accessible 3 ½ inch drive (hard disk) ● one accessible 5 ¼ inch drive (e.g. DVD or CD ROM drive) "Accessible drives" are e.g. DVD or CD ROM drives, into which a data carrier can be ins

  • Fujitsu ESPRIMO E5635, Fujitsu Technology Solutions 7 Preparing for use ! Please take note of the safety information in the " Important notes" chapter. Unpacking and checking the delivery It is recommended not to throw away the original packaging material! It may be required for reshipment at some later date. ► Unpack all the individual parts. ► Check the delivery for damage incurred during transportation. ► Check whether the delivery agrees with the details in the delivery note. Should you discover that the deliver

  • Fujitsu ESPRIMO E5635, Troubleshooting and tips Fujitsu Technology Solutions 33 The screen stays blank If your screen remains blank this may be due to the following: Monitor is switched off ► Switch your monitor on. Power saving has been activated (screen is blank) ► Press any key on the keyboard. or ► Deactivate the screen saver. If necessary, enter the appropriate password. Brightness control is set to dark ► Adjust the brightness control. For detailed information, please refer to the operating manual supplied with y

  • Fujitsu ESPRIMO E5635, System expansions Fujitsu Technology Solutions 75 Replacing lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced. For 0-Watt devices: As an interim solution, the device can be started using the emergency on button at the rear, see chapter " Switching on a device when the lithium battery is disch

More Instructions:

DOWNLOAD

Related Products and Documents (Desktop):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Memorex MX4107 Operation & user’s manual memorex/mx4107-J5Q.pdf 23 Oct 2023 17
2 Makita 6911D Instruction manual makita/6911d-Y6Y.pdf 03 Mar 2023 16
3 Manitowoc GR1200A Installation instructions manual manitowoc/gr1200a-4EH.pdf 31 Aug 2022 16
4 OV Solutions ovc-3bvirsf Operation & user’s manual ov-solutions/ovc-3bvirsf-Q44.pdf 28 Aug 2022 69
5 Kramer VS-88A Operation & user’s manual kramer/vs-88a-5SL.pdf 08 Nov 2022 37
6 Bamboo QJ18 Operation & user’s manual bamboo/qj18-Z27.pdf 21 Feb 2024 6

Similar Resources:

  • HP

    Brio 71xx

    (16 pages)
    installation guideinstallationshandbuchguide d’installationguía de instalaciónléase este primeroguida di installazionewww.hp.com/go/pcaccessorieshp IDE hard disk drivefront.fm Page 1 Friday, August 10, 2001 2:36 PM …
  • HP

    D7171A - NetServer - LPr

    (2 pages)
    System BoardBCabinetAHP NetServer LH 3 and LH 3r Technical Reference Card1.2.3.4.5.6.7.8.9.Boot OrderIDE CD-ROMFloppy DriveEmbedded SCSIPCI 6PCI 5PCI 4PCI 3PCI 2PCI 11.2.3.4.5.6.7.8.9.10.11.Default Boot OrderIDE CD-ROM DriveFlexible Disk DriveEmbedded SCSIPCI 8PCI 7PCI 6PCI 5PCI 4PCI 3PCI 2ISA / PCI 1DIMM InstallationDSystem SwitchesCMonitorSerial BSerial AP …
  • Sony

    PCV-RZ50C VAIO User Guide (primary manual)

    (245 pages)
    Welcome Thank you for purchasing a Sony VAIO® computer! Your new computer is a superb blend of high technology and easy-to-usefunctionality. The information provided here is designed to help you to become familiar with the hardware and softwareprograms included with your system. View the Electronic Flyer, which provides updates and supplemental informati …
  • Unitech

    PA600

    (11 pages)
    Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.PA600 Rugged Enterprise PDAQuick Reference Guide 400577G RevBunitech unitech unitech is a member of Oracle Embedded Software Licens-ing Program …
  • Casio

    Cassiopeia E-200

    (65 pages)
    Pocket PCUser’s GuideYour Pocket PC 2002 comes with a Hardware Manual in addition tothis Pocket PC User’s Guide. Be sure to read the Hardware Manualfirst.Before using your Pocket PC for the first time,carefully read theSafety Precautions in the Hardware Manual.Keep this Pocket PC User’s Guide on hand for reference wheneverusing your Pocket PC.E …
  • NEC

    C SERIES

    (26 pages)
    User’s ManualC Series ShadowSenseTMTouchMultiSync C751Q SSTMultiSync C861Q SSTMultiSync C981Q SSTMONITOR MODEL: C751Q SST, C861Q SST, C981Q SSTPlease find your model name on the label on rear side of the monitor. …

Comments, Questions and Opinions: