Manualios.com

Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC Installation Manual

  • BARRACUDA 4LP ST32171N/W/WC/WD/DC DVD Recorder
  • ma1LlVAvNUg7Y
  • Installation Manual
  • PDF / Adobe Acrobat Reader
  • 52

Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC Manual Online:

3.05, 2974 votes
Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC User Manual
Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC User Guide
Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC Online Manual

Text of Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC User Guide:

  • Barracuda 4LP Installation Guide, Rev. B 9 SeaBOARD ® SeaBOARD is a computer bulletin board system (BBS) that con- tains information about Seagate’s disc and tape drive products and is available 24 hours daily. Set your communications soft- ware to eight data bits, no parity, and one stop bit (8-N-1). Sea- BOARD phone numbers are listed in the following table. Se

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, Barracuda 4LP Installation Guide, Rev. B 23 [1] “X” means up to 6 or the maximum allowable number of devices on the SCSI bus. See Table 4 and system documentation. Figure 3c. Multiple drive connection to host adapter Host Adapter PCB Pin 1 (check your adapter for Pin 1 location) SCSI ID X (or last drive) [1] SCSI ID 1 SCSI ID 0 SCSI ID 7 Additional SCSI devices “N” Model Drive

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, Barracuda 4LP Installation Guide, Rev. B 31 defined in IEC 950. Figure 5 provides the pin information for the DC power connector. To connect the DC power cable to the drive, simply insert the cable end into the drive’s DC power connector. 4. Schließen Sie das SCSI-Kabel an den SCSI-Steckverbinder des Laufwerkes an. Das Kabel darf nicht gedehnt oder gedrückt werden und es darf den Luftstrom zur Kühlung des Systems nicht behindern. Das Laufwerk wird über einen 4-poligen, neben dem SCSI- Anschluß befestigten Steckverbinder mit Gleichstrom ver- sorgt. Der Ausgang eines Netzteils muß SELV (safety extra low voltage) nach IEC 950 entsprechen. Abbildung 5 zeigt die Steckerbelegung für den

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 40 Barracuda 4LP Installation Guide, Rev. B W/WD drives W/WD drives sectionSetting the SCSI ID jumpers Use the J6 jumper block to set the SCSI ID (Figure 11). To change the SCSI ID, install jumpers on the appropriate pins as shown in the illustration. Optional connections to switching cir- cuits in host equipment are provided on J1 auxiliary to set the SCSI ID (see Figure 12). Figure 11. Setting the SCSI ID on model W/WD drives A 2 A 3 A 1 A 0 SCSI ID = 0 (default) SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 Reserved L E D R E S SCSI ID =

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, Barracuda 4LP Installation Guide, Rev. B 13 Table 1. Drive characteristics Interface UltraSCSI [1] Capacity Formatted [2] Unformatted ST34371 4.35 Gbyte [2] 5.31 Gbyte ST32171 2.16 Gbyte [2] 2.65 Gbyte ST34571 4.55 Gbyte [2] 5.54 Gbyte ST32271 2.26 Gbyte [2] 2.77 Gbyte Recording Cylinders (user) 5,178 Read/write data heads ST32171/ST32271 5 ST34371/ST34571 10 Access time [3] Average read 9.4 msec Average write 10.4 msec Disk rotation RPM 7,200 r/min Average latency 4.17 msec Internal transfer rate (variable with zone) ST32171/ST34371 80–122 Mbits/sec ST32271/ST3

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 30 Barracuda 4LP Installation Guide, Rev. B 1. Befestigen Sie das Laufwerk mit vier 6-32-UNC-Schrauben am Gehäuse des Host-Systems. Die beiden Seiten des Laufwerkes sind mit jeweils zwei Befestigungslöchern versehen, die Unterseite des Laufwerkes weist vier weitere Befestigungslöcher auf. Gemessen von der Außenfläche des Gehäuses dürfen die Schrauben maximal 3,81 mm in die Befestigungslöcher des Gehüuses hineinragen. Die Schrauben müssen gleich- mäßig, jedoch nicht zu fest, angezogen werden. Wenn sich eine Schraube nic

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, Barracuda 4LP Installation Guide, Rev. B 29 Mounting the drive and connecting cables Do not touch the connector pins or any components on the con- trol board without observing static-discharge precautions. Always handle the drive by the frame only. The drive may be mounted in any orientation (horizontally, verti- cally, and any combination thereof); however, you must ensure that the drive receives adequate air flow for cooling. 1. Mount the drive to the host system’s chassis using four 6-32 UNC screws. Two mounting holes are in eac

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, Contents Preface ........................................................................................1 Electrostatic discharge protection................................................1 Important safety information and precautions..............................2 Wichtige Sicherheitshinweise ......................................................4 European Union Compliance.......................................................7 Technical support services...........................................................8 General description....................................................................12 Initial setup

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, Barracuda 4LP Installation Guide, Rev. B 1 Preface This manual contains information for users of the Seagate® Barracuda 4LP SCSI disc drives. It provides support services, performance specifications, and initial setup information. Addi- tional information is available in the Barracuda 4LP Product Manual (part number 77767491). Contact your Seagate sales representative if you need to order this publication. Electrostatic discharge protection Caution. Removal of circuit boards by personnel not perform- ing depot repair will damage components and may void the warranty. All drive electronic assemblies are sensitive to static electric

  • Barracuda 4LP Installation Guide, Rev. B 11 Before calling, note your system configuration and drive model number (ST xxxx ). There are several technical support phone numbers available for various Seagate products. SeaTDD ™ 408-944-9121 Using a telecommunications device for the deaf (TDD), you can send questions or comments 24 hours daily and exchange mes- sages with a technical support

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, Barracuda 4LP Installation Guide, Rev. B 27 Kühlung des Systems Die Gehäusekonstruktion muß eine ausreichende Kühlung des Laufwerkes gewährleisten. Die Umgebungstemperatur darf maximal 50°C betragen. Die Produkthandbuch Barracuda 4LP (Dokument 77767491) enthalten Anweisungen zur Beurteilung der Luftstromkonstruk- tion. Die Beurteilung muß sicherstellen, daß sich die Gehäuse- temperatur bestimmter kritischer Komponenten bei Laufwerkbetrieb innerhalb zugelassener Grenzen hält. Wir empfehlen, das Laufwerk so zu orientieren oder den Luft- stro

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 32 Barracuda 4LP Installation Guide, Rev. B Note. Signal ground on the power control board (PCB) and the head and disc assembly (HDA) are connected together in this drive and you cannot separate them. The equipment in which you have mounted the drive is connected directly to the HDA and PCB without electrically isolating shock mounts. Maximizing the conductive contact area between HDA ground and system ground may reduce radiated emissions. If you do not want the system chassis to be connected to the HDA/PCB ground, you must provide a nonconductive (electrically isolating) method of mounting the drive in the host system. This may increase radiated emissions and is the s

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, Barracuda 4LP Installation Guide, Rev. B 7 magnetische Strahlung sind für Designer von Untersystemen auf Anfrage von der Seagate-Sicherheitsabteilung erhältlich. European Union Compliance If this model has the CE Marking, it complies with the European Union requirements of the Electromagnetic Compatibility Direc- tive 89/336/EEC of 03 May 1989 as amended by Directive 92/ 31/EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993. Seagate uses an independent laboratory to confirm compliance to the above directives. Th

  • 10 Barracuda 4LP Installation Guide, Rev. B Seagate Technology FAX services SeaFAX ® You can use a touch-tone telephone to access Seagate’s auto- mated FAX system to receive technical support information by return FAX. This service is available 24 hours daily. Seagate technical support FAX You can FAX questions or comments to technical support spe- cialists 24 hours daily. R

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 46 Barracuda 4LP Installation Guide, Rev. B WC/DC drives Applicable jumper options Option jumpers are available as illustrated below. Figure 16. Jumper options Enable parity check of SCSI bus. Disable parity check. Parity Check option Write protect = Off  (enables writing) Write protect = On  (disables writing) Write Protect option The host system has complete  control over motor start functions. Do  not install a jumper on these pins. Delay Motor Start option The host system has complete  control over motor start functions. Do  not install a jumper on these pins. Enable Motor Start option  T E  D

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 20 Barracuda 4LP Installation Guide, Rev. B For information about how to terminate your drive, refer to the appropriate drive-specific section. Figure 2. SCSI bus termination Terminator power You usually will not need to change this option and can normally leave the drive configured as it was shipped from the factory. For information about how to change the terminator power option on your drive, refer to the appropriate drive-specific section. I/O circuits and data path widths • “WD” and “DC” models use differential I/O circuits. You cannot mix these models with single-ended models (“N,” “W,” “WC”) on the same SCSI bus. The circuits are incompatible with each other

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 38 Barracuda 4LP Installation Guide, Rev. B N drives Terminator power There are three possible terminator power (TP) configurations for “N” model drives (see Figure 9). You will not normally need to change this option and can leave the drive configured as it was shipped from the factory. Figure 9. Setting terminator power jumpers Term. Power to SCSI Bus Term. Power from Drive (default) “N” model drives  T E  D S  M E  W P  P D R E S  T P  T P Term. Power from SCSI Bus Position A SCSI I/O Connector DC Power Connector J2 Drive Front J6 J1 J2 Jumper Type (enlarged to show detail) Pin 1 J2

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 44 Barracuda 4LP Installation Guide, Rev. B W/WD drives Other applicable jumper options Other option jumpers are available as illustrated below. Figure 15. Additional jumper options Enable parity check of  SCSI bus. Disable parity check. J2 Pin 1 Reserved Parity Check option Write protect = Off  (enables writing. Write protect = On  (disables writing). Write Protect option Disable the Delay Motor  Start option. Motor start delay equal  to the SCSI ID multiplied  by 12 seconds. For  example, if the SCSI  ID = 2, the drive starts  in 24 seconds. Delay Motor Start option  (vali

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, •••••••••••••••••••••••••• •••••••••••••••••••••••••• •••••••••••••••••••••••••• •••••••••••••••••••••••••• •••••••••••••••••••••••••• •••••••••••••••••••••••••• Barracuda 4LP Disc Drive ST34371N/W/WC/WD/DC ST32171N/W/WC/WD/DC ST34571N/W/WC/WD/DC ST32271N/W/WC/WD/DC Installation Guide •••••••••••••••••

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, Barracuda 4LP Installation Guide, Rev. B 15 Table 2b. DC power requirements (Amps) [1] Measured with an average reading DC ammeter. Instanta- neous +12V current peaks will exceed these values. [2] A –10% droop is permissible during initial start of the spindle but must return to ±5% before reaching 7,200 RPM. The ±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the drive is able to accept selection by the host initiator. [3] See the +12V current profile in the Barracuda 4LP Product Manual (publication number 77767491). [4] This condition occurs when the Motor Start option is enabled and the drive has not yet re

  • Barracuda 4LP Installation Guide, Rev. B 41 W/WD drives Figure 12. Using J1-Auxillary connector for model “W” and “WD” drive alternate ID select and LED connection J1-DC Power J1 68 Pin SCSI I/O Connector Drive HDA Rear SCSI ID = 8 SCSI ID = 9 SCSI ID = 10 SCSI ID = 11 SCSI ID = 12 SCSI ID = 13 SCSI ID = 14 SCSI ID = 15 A not used 3 A 2 A

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 42 Barracuda 4LP Installation Guide, Rev. B W/WD drives Terminating the drive “W” model drives are terminated with permanently mounted IC active terminators. If you install one of these drives and it is not on the end of the SCSI bus, disable the terminators by removing the jumper “TE” from pins 15 and 16 of connector J2. If you install the drive on the end of the SCSI bus, enable termination by installing a jumper on pins 15 and 16 of connector J2 (see Figure 13). Note. Use active (ANSI SCSI-2

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 34 Barracuda 4LP Installation Guide, Rev. B Figure 6. Mounting configuration dimensions A F D E L [1] [3] B G [1] Mounting holes three on each side, 6-32 UNC.  Max screw length into side of drive 0.15 in.  (3.81 mm). Screw tightening torque 6.0 in-lb  (.675 NM) max with minimum thread  engagement of 0.12 in. (3.05 mm).  [2] Mounting holes four on bottom, 6-32 UNC.  Max screw length into bottom of drive 0.20 in.  (5.08 mm). Screw tightening torque 6.0 in-lb  (.675 NM) max with minimum thread  engageme

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 24 Barracuda 4LP Installation Guide, Rev. B [1] Do not mix “W” and “WD” model drives on the daisy chain. [2] “X” means up to 15 or the maximum allowable number of devices on the SCSI bus. See Table 4 and system documentation. [3] External terminator. Figure 3d. Multiple-drive connection to host adapter Host Adapter PCB Pin 1 (check your adapter for Pin 1 location) “W” Model Drive [1] “WD” Model Drive [1] SCSI ID 1 SCSI ID 0 SCSI ID 7 SCSI ID X (or last drive) [2] Additional SCSI devices [3]

  • Seagate BARRACUDA 4LP ST32171N/W/WC/WD/DC, 8 Barracuda 4LP Installation Guide, Rev. B Technical support services If you need assistance installing your drive, consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If you need additional assistance with your Seagate ® drive or other Seagate products, use one of the Seagate technical sup- port services listed below. SeaFONE ® at 1-800-SEAGATE (1-800-732-4283) Seagate’s 800 number allows toll-free access to automated self- help services, providing answers to commonly asked questions, troubleshooting tips, and s

Related Products and Documents (DVD Recorder):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Withings Body Cardio Quick installation manual withings/body-cardio-B6V.pdf 02 Jul 2022 12
2 Disc Makers Reflex4 Quick start manual disc-makers/reflex4-2L8.pdf 01 Sep 2023 2 0.23 Mb
3 Lectrosonics AM8 Operating instructions and owner's manual lectrosonics/am8-883.pdf 06 Jan 2024 28
4 IBM 19K4206PT1 Operation & user’s manual ibm/19k4206pt1-6A8.pdf 30 Dec 2022 10
5 SPT SK-1715 Instruction manual spt/sk-1715-3J6.pdf 02 Jul 2022 6 0.08 Mb
6 LG KE970 Service manual lg/ke970-OXI.pdf 04 Apr 2023 160

Similar Resources:

  • Pioneer

    DVR-940HX-S

    (172 pages)
    Operating InstructionsDiscover the benefits of registering your product online at www.pioneer.co.uk (www.pioneer-eur.com)DVR-940HX-SDVR-545HX-SDVD RECORDERDVD RECORDEROperating Instructions<VRB1456-A>Printed in UKK002_A_EnPublished by Pioneer Corporation.Copyright © 2006 Pioneer Corporation.All rights reserved.PIONEER CORPORATION4-1, Meguro 1-Chome, M …
  • Sony

    BDP-BX110

    (1 pages)
    LIMITED WARRANTY (U.S. Only)Sony Electronics Inc. (“Sony”) warrants this product against defects in material or workmanship for the timeperiods and as set forth below when purchased directly from Sony or a Sony Retailer. Pursuant to this LimitedWarranty, Sony will, at its option, (i) repair the product using new or refurbished parts or (ii) replace the p …
  • Panasonic

    DMR ES15 - DIGA DVD Recorder

    (52 pages)
    RQT8317-LOperating InstructionsDVD RecorderDMR-ES15Model No. GN GC GCA GCSFor Australia and N.Z.Getting startedRecordingPlaying backEditingCopyingConvenient functionsReferenceDear customerThank you for purchasing this product. For optimum performance and safety, please read these instructions carefully.Before connecting, operating or adjusting this product, …
  • LG

    RHT497H

    (44 pages)
    Freeview+ DVD Recorder with HDDUSER MANUALRHT497H/RHT498H/RHT499HAs an ENERGY STAR® Partner, LG has determined that this productor product models meet theENERGY STAR® guidelines forenergy efficiency.ENERGY STAR® is a U.S. registered mark.LG RHT49X instructions.indd 1LG RHT49X instructions.indd 1 2009-03-04  3:50:122009-03-04  3:50:12 …
  • Pioneer

    DVR-541H-S

    (140 pages)
    <VRB1414-A>Printed in ChinaDVD RecorderDVR-640H-SDVR-541H-SDVR-340H-SOperating InstructionsDVD RECORDEROperating InstructionsK002_A_EnPublished by Pioneer Corporation.Copyright © 2006 Pioneer Corporation.All rights reserved.PIONEER CORPORATION4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, JapanPIONEER ELECTRONICS (USA) INC.P.O. BOX 1540, Long Beach, …
  • Internatonal Taretronics

    PD-II Series

    (58 pages)
    www.SteamPoweredRadio.ComTECHNICAL MANUAL PD-II S'ERliES CARTRIDGE RECORDER AND REPRODUCER 1nTe.RnAr1onAL TAPETROn1ICS CORPORATIOn 2425 South Main Street Bloomi;ngton, Illinois 61701 Telephone : 309-828-11381 …

Comments, Questions and Opinions: