Manualios.com

Fujitsu D3081 Technical Manual

Fujitsu D3081 Manual Online:

3.95, 2876 votes
Fujitsu D3081 User Manual
Fujitsu D3081 User Guide
Fujitsu D3081 Online Manual

Text of Fujitsu D3081 User Guide:

  • Fujitsu D3081, 12 Technical Manual D3081, D3131, D3082 (RX900 S1) Important information V CAUTION! ● Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. There is a danger of burns! ● Transmission lines to peripheral devices must be adequately shielded. ● Ethernet cabling has to comply with EN 50173 and EN 50174-1/2 standards or ISO/IEC 11801 standard respectively. The minimum requirement is a Category 5 shielded cable for 10/100 Ethernet, or Category 5e for Gigabit Ethernet. ● Never connect or disconnect data transmission lines during a storm (risk of lig

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 51 Features Figure 13 shows the indicators on the baseboard where the individual indicators are named in table 14. Pos. Connector Pos. Connector A PCI Riser H Chassis ID board B I/O board I Operator panel C PCIe slots on the baseboard J Power distribution board D Trusted Platform Module (TPM) K Front video connector E USB Flash Module (UFM) L Front USB connector F FAN M SATA optical disk drive G CPU Memory Riser Table 13: Onboard connectors baseboard D3081

  • D3081, D3131, D3082 (RX900 S1) Technical Manual 59 Features Pos. Indicator Function Description A Activity LAN link/transfer (1 GB system LAN) Steady green signal: LAN connection exists. Remains dark: no LAN connection exists. Flashes green: LAN transfer takes place. B 10/100/1000 LAN speed (1 GB system LAN) Steady yellow signal: LAN transfer rate of 1 Gbit/s. Steady green signal: LAN tra

  • Fujitsu D3081, Technical Manual D3081, D3131, D3082 (RX900 S1) Contents 3.7 Connectors and indicators . . . . . . . . . . . . . . . . . . . 49 3.7.1 Onboard connectors and indicators . . . . . . . . . . . . . . . . 50 3.7.1.1 Baseboard D3081 . . . . . . . . . . . . . . . . . . . . . . 50 3.7.1.2 CPU Memory Riser (CPUMEMR) D3131 . . . . . . . . . . . 53 3.7.1.3 PCI Riser (PCIR) D3082 . . . . . . . . . . . . . . . . . . . 54 3.7.1.4 I/O board . . . . . . . . . . . . . . . . . . . . . . . . . .

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 15 Important information 2.3 Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account. This saves resources and thus reduces the harm done to the environment. Further information can be found at: – http://ts.fujitsu.com/products/standard_servers/ind

  • D3081, D3131, D3082 (RX900 S1) Technical Manual 57 Features 3.7.3 External connectors and indicators 3.7.3.1 Baseboard D3081 Figure 18 shows the external connectors and indicators on the baseboard where the individual connectors and indicators are named in table 18. The LAN indicators are explained in table 19. Figure 18: External connectors of the baseboard D3081 Pos.

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 27 Features 3.2.1.3 QPI topology The server uses an interconnect "Intel® QuickPath Interconnect (QPI)" for the connection between the CPUs and CPU I/O Hubs (IOH). Each CPU has 4 QPI ports and the IOH has 2 QPI ports. Figure 3 shows the QPI topology where the numbers (0, 1; 0, 1, 2, 3) indicate the QPI port number of the CPU/IOH. Figure 3: QPI topology Initially, the RX900 S1 can be configured with 4, 6, or 8 CPUMEMRs and each CPUMEMR includes one CPU. If one of the CPUs is removed, the system uses all of the remaining CPUs that form a consistent QPI topology. If removing one CPU would result in an unsupported configuratio

  • 24 Technical Manual D3081, D3131, D3082 (RX900 S1) Features 3.2.1.1 DIMM slot population order CPUMEMRs are populated in four steps. In each step, four DIMM memory modules are added. At least four DIMM memory modules must be installed on CPUMEMR #1 and #2. CPUMEMRs #3 to #8 can be left empty. Ta ble 3 shows the DIMM slot population order for an individual CPUMEMR

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 55 Features 3.7.1.4 I/O board Figure 16 shows the onboard connector on the I/O board. Figure 16: Onboard connector on the I/0 board 3.7.2 Onboard DIP switch Figure 17 shows the position of the DIP switch where the DIP switch settings are named in table 17. I Default setting: Switches 1 to 4 are set to Off. Pos. Connector A 1x USB connector C A

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 25 Features Figure 2: DIMM slot population order for an individual CPUMEMR 3.2.1.2 DIMM slot population rules for mixed DIMM RANK Basic configuration rules for populating the two slots associated with the same DDR3 channel are: ● The slot with the lower sequence number is populated first. ● 1RANK- and 2RANK-DIMM memory modules can be inserted in both slots. ● 4RANK-DIMM memory modules must be installed in the slot with the lower sequence number or in both slots. B1C 1D 1E 1F 1G 1H 1A 1B B 2C 2D 2E 2F 2G 2H 2A 2B #A#B #C #D C I C I C I C I C J C J C J C J C K C L

  • Fujitsu D3081, Technical Manual D3081, D3131, D3082 (RX900 S1) These uses include control of nuclear reactions in nuclear power plants, automatic airplane flight control, air traffic control, traffic control in mass transport systems, medical devices for life support, and missile guidance control in weapons systems (hereafter, "high safety use"). Customers should not use this product for high safety use unless measures are in place for ensuring the level of safety demanded of such use. Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in th

  • 48 Technical Manual D3081, D3131, D3082 (RX900 S1) Features 3.5 Screen resolutions The screen resolution that applies to the internal graphics controller depends on the operating system in use, see table 12. 3.6 Temperature / System monitoring Temperature and system monitoring aims to reliably protect the hardware from overheating and to provide information on th

  • Fujitsu D3081, 50 Technical Manual D3081, D3131, D3082 (RX900 S1) Features 3.7.1 Onboard connectors and indicators 3.7.1.1 Baseboard D3081 Figure 12 shows the onboard connectors on the baseboard where the individual connectors are named in table 13. Figure 12: Onboard connectors baseboard D3081      $#! "         D C A C B C C C D C E C F C G C H C I C J C K C L C M

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 61 Features 3.7.3.2 I/O board Figure 20 shows the external connectors on the I/O board where the individual connectors and indicators are named in table 20. Figure 20: External connectors on the I/O board The serial connector COM1 can be used as default interface or to communicate with the iRMC S2. Pos. Connector A4x USB BSerial COM1 C Video Table 20: External connectors on the I/O board C A C C C B

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 47 Features PCIe slot #13 #4 IOH #4 not recognized IOH #4 not recognized Max 2 1 PCIe slot #14 2 PCIe slot #15 3 PCIe slot #16 4 PCIe slot #17 5 Sum Max 16 Max 16 Max 16 Device / slot I/O Hub I/O space block (4 KB each) Remark 4 CPUs 6 CPUs 8 CPUs Assign order Table 11: I/O space assignment for 4, 6, and 8 CPU configurations

  • Fujitsu D3081, 32 Technical Manual D3081, D3131, D3082 (RX900 S1) Features Figure 7: Memory mirroring in a 6 or 8 CPUMEMR configuration On both CPUMEMRs of the mirroring pair, the size of the DIMMs must be the same within the following groups of memory modules, see figure 5: ● DIMM# (1B, 1D, 1F, 1H) ● DIMM# (1A, 1C, 1E, 1G) ● DIMM# (2B, 2D, 2F, 2H) ● DIMM# (2A, 2C, 2E, 2G) Scenarios for memory mirroring interruption If failed or disabled DIMM memory modules are detected, the impact on the mirroring configuration is: 1. A group of DIMM memor

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 63 4 Replacing the lithium battery To allow permanent saving of the system information, a lithium battery is installed which supplies the CMOS memory with power. If the battery voltage is too low or the battery is empty, a corresponding error message is displayed. The lithium battery must then be replaced. The replacement procedure is explained in the "PRIMERGY RX900 S1 Server Maintenance Manual".

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 41 Features *1) The SAS RAID controller shall not be installed in PCIe slot #1 to #7 on the PCI Riser when a BBU is connected because of limited length of the BBU cable. *2) The Quad LAN card consumes twice as much I/O space as a standard expansion card because it includes a bridge within the card. If you install this card into slot#1 or slot#2, no I/O resource will be assigned to the onboard GbE controller. Chipset IOH#3 IOH#4 Bus scan order 12 11 10 9 17 16 15 14 13 I/O space assigning order within

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 37 Features 3.3.1 PCI interrupt assignment The BIOS assigns the PCI interrupts automatically. Further settings are not possible. 3.3.2 PCIe slot to CPUMEMR assignment Figure 10 shows the assignment of PCIe slots to the 4 I/O Hubs and the 4 - 8 CPUMEMRs. I Before adding an expansion card, check carefully whether this PCIe slot is supported with the CPUMEMR configuration of the individual server. Pos. Slot no. Description Hot-plug A PCI Riser (PCIR) C #5 PCI Express 2.0 (x4), 1/2 length, x8 connec

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 39 Features CPU population order CPU - IOH mapping Connected devices Remark 4 CPUs 6 CPUs 8 CPUs CPU No. IOH No. CPU#1 x x x #1 or #2 #1 ICH10 PCIe #5 to BMC CPU#2 x x x BMC (VGA) GbE#1, GbE#2, GbE#3, 10GbE#1 PCIe slot #8 Modular RAID PCIe slot #1 PCI Riser PCIe slot #2 PCI Riser CPU#3 x x x #3 or #4 #2 PCIe slot #5 PCI Riser; Gen2x4 CPU#4 x x x PCIe slot #3 PCI Riser PCIe slot #4 PCI Riser PCIe slot #6 PCI Riser PCIe slot #7 PCI Riser CPU#5 x x #5 or #6 #3 PCIe slot #

  • 54 Technical Manual D3081, D3131, D3082 (RX900 S1) Features 3.7.1.3 PCI Riser (PCIR) D3082 Figure 15 shows the onboard connectors and indicators on the PCIR where the individual connectors and indicators are named in table 16. Figure 15: Onboard connectors and indicators PCIR D3082 Pos. Connector Pos. Indicator A PCIe slots C PCIe CSS B PCIR D CSS button Table 16: Onboard

  • Fujitsu D3081, 58 Technical Manual D3081, D3131, D3082 (RX900 S1) Features The system is equipped with one Dual 10 GB Ethernet Controller type Intel 82599. In addition, three Dual 1 GB Ethernet Controller type Intel 82576 NS (system LAN) are installed supporting transmission rates of 10 Mbit/s, 100 Mbit/s, and (only for system LAN) 1 Gbit/s. The 1Gb Ethernet LAN controllers support WoL functionality by means of Magic Packet™. It is also possible to boot a system without its own boot hard disk via LAN. PXE is supported for this. The separate management LAN connector is used as a management interface (iRMC S2) and is prepared for operation with

  • Fujitsu D3081, D3081, D3131, D3082 (RX900 S1) Technical Manual 43 Features *1) WinPE does not require I/O space but some drivers require I/O space for loading properly. *2) When both Legacy OPROM and EFI driver are available, the BIOS loads the EFI driver and the Legacy service is provided by the CSM module, that is the Legacy OPROM is not loaded. 3.4.2 I/O space limitation The I/O space is limited to 64 KB. Each PCI Bridge assigns its I/O space in several blocks of 4 KB. ICH10 requires 1-block for Legacy support. Au

Related Products and Documents (Motherboard):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Accel Hobby Katana EP Instruction manual accel-hobby/katana-ep-655.pdf 14 Jul 2022 9
2 LockUP LockUp M Operating manual lockup/lockup-m-2Z9.pdf 01 Sep 2023 4
3 Johnson Controls VA-9070 Series Installation instructions johnson-controls/va-9070-series-894.pdf 18 Sep 2023 2
4 Kyocera FS-C1020MFP Quick installation manual kyocera/fs-c1020mfp-8GS.pdf 15 Oct 2022 2
5 Kewtech KEW337 Instruction manual kewtech/kew337-96B.pdf 05 Dec 2022 2
6 Omron M5-I Instruction manual omron/m5-i-TNV.pdf 27 Jun 2023 14

Similar Resources:

  • AXIOMTEK

    ETM831 Series

    (2 pages)
    ETM831 Series Quick Installation Guide ©Copyright 2009 AXIOMTEK Co., Ltd. Version A1 November 2009 Printed in Taiwan 9418G831000E 4 Figure 2: ETM831 Thermal Solution Design Guide Please refer to the ETM831 Series Product Information CD for the complete User’s Manual, drivers and utilities. User’s Manual and related documents are Acrobat PDF format …
  • QDI

    P5I945P

    (55 pages)
    NoticeThe information in this document is subject tochange in order to improve reliability, design, orfunction without prior notice and does not repre-sent a commitment on the part of this company.In no event will we be liable for direct, indirect,special, incidental, or consequential damagesarising out of the use or the possibility of suchdamages.All tradem …
  • Global American

    2808060

    (69 pages)
    User’s Manual 2808060 Mini-ITX Mainboard Version 1.0, October 2008 …
  • Analog Devices

    EVAL-AD7492SDZ

    (24 pages)
    EVAL-AD7492SDZ User Guide UG-371 One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluation Board for the AD7492 1.25 MSPS, 16 mW Internal REF and CLK, 12-Bit Parallel ADC PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | …
  • Texas Instruments

    TPS25940XEVM-635

    (17 pages)
    User's GuideSLVUA44–June 2014TPS25940XEVM-635: Evaluation Module for TPS25940XThis user’s guide describes the evaluation module (EVM) for the Texas instruments TPS25940X devices.TPS25940X devices are eFuse with true reverse blocking for power mux that operates from 2.7 V to 18 V,the device has integrated back-to-back FETs with programmable undervolt …
  • Erone

    SEL2641R433-P4P

    (16 pages)
    SEL2641R433-P4P Radioprogrammatore 400W PlusRadioprogrammer 400W PlusRécepteur séquentiel 400W PlusFunkmotorsteuerung 400W PlusManuale d’installazione ed uso - Italiano ............Pag. 4Use and installation Manual - English .................Pag. 7Notices d’installation et utilisation - Français .....Pag. 10Pag. 13Bedienungsanleitung - Deutsch .... …

Comments, Questions and Opinions: