Fujitsu CW35 Series Operation & User’s Manual

Text of Fujitsu CW35 Series User Guide:

• Fujitsu CW35 Series, 2 20 Hardware Installation 2.5 Jumper Settings for the Audio Codec Jumper JP7 Enable/Disable Audio Codec This jumper is used to enable or disable the audio codec (AC97) on the system board. By default, the onboard audio codec is enabled. If you are using the AMR cards audio codec, set pins 2 and 3 to On. Please refer to the following table on how the jumper and the BIOS should be configured in different situations or system configurations. 3. If you are using the (1) Suspend to RAM, (2) Wake-On- Keyboard/Mouse and (3) Wake-On-LAN functions all at the same time, the 5VSB power source of your power supply must support a minimum of ≥ 1A.

• Fujitsu CW35 Series, 45 3 Award BIOS Setup Utility Halt On This category determines whether the system will stop if an error is detected during power up. The default setting is All Errors. No Errors The system boot will not stop for any errors detected. All Errors The system boot will stop whenever the BIOS detects a non-fatal error. All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors. All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors. All, But Disk/Key The system boot will not stop for a disk or keyboard error; it will stop for all other errors. Base Memory Displays the amount of base (or conventional) memory

• 2 30 Hardware Installation 2.9.7 IrDA Connector The system board is equipped with an IrDA connector for wireless connectivity between your computer and peripheral devices. The IRDA (Infrared Data Association) specification supports data transfers of 115K baud at a distance of 1 meter. Connect your IrDA cable to connector J1 on the system board. Set UART2 Mode Selec

• Fujitsu CW35 Series, 71 4 Supported Softwares 4.1.2 Using the DMI Utility The four menus located on top of the DMI Configuration Utility screen are Edit DMI, Add DMI, Load DMI File and Save DMI File. Use the ← or → (left or right) arrow keys to select a menu from the Menu bar. On the left side of the screen is a list of the system configuration items. Use the ↑ or ↓ (up or down) arrow keys to select an item. The commands at the bottom of the screen will allow you to navigate through the various setup menus. Edit DMI 1. Use the ← or → arrow keys to select the Edit DMI menu. 2. Highlight the i

• Fujitsu CW35 Series, 64 3 Award BIOS Setup Utility IRQ Resources This field is used to set each system interrupt to either Legacy ISA or PCI. PCI For devices compliant with the PCI bus architecture. Legacy ISA For devices compliant with the original PC AT bus specification. Memory Resources This field is used to select the reserved memory base and reserved memory length of any peripherals that require high memory. Reserved Memory Base The options are N/A, C800, CC00, D000, D400, D800 and DC00. Reserved Memory Length The options are 8K, 16K, 32K and 64K. PCI/VGA Palette Snoop This field determines whether the MPEG ISA/VESA VGA cards can work with PCI/VGA

• Fujitsu CW35 Series, Introduction 1 8 Onboard Audio Features  Supports Microsoft ® DirectSound  32-voice wavetable synthesis  AC97 supported with full duplex, independent sample rate con- verter for audio recording and playback  Downloadable sound (DLS) level-1 Compatibility  Microsoft PC 98 compliant  VESA Display Power Management Signaling (DPMS)  VESA DDC2B for Plug and Play monitors  PCI 2.2, AMR 1.0 and AC 97 compliant ATX Double Deck Ports (PC 99 color-coded connectors)  Two USB ports  One NS16C550A-compatible DB-9 serial port  One DB-15 VGA port  One SPP/ECP/EPP DB-25 parallel port  One mini-DIN-6 PS/2 mouse port  O

• Fujitsu CW35 Series, 2 26 Hardware Installation 2.9.2 PS/2 Mouse and PS/2 Keyboard Ports The system board is equipped with an onboard PS/2 mouse (CN1 - Green) and PS/2 keyboard (CN2 - Purple) ports located at the ATX double deck ports of the system board. The PS/2 mouse port uses IRQ12. If a mouse is not connected to this port, the system will reserve IRQ12 for other expansion cards. Warning: Make sure to turn off your computer prior to connecting or disconnect- ing a mouse or keyboard. Failure to do so may damage the system board. 2.9.3 Parallel Port The system board has a stan- dard printer port (CN4 - Burgundy) located at the ATX double deck p

• Fujitsu CW35 Series, 46 3 Award BIOS Setup Utility 3.1.2 Advanced BIOS Features The Advanced BIOS Features allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference. The settings on the screen are for reference only. Your version may not be identical to this one. Virus Warning This category protects the boot sector and partition table of your hard disk drive. When this item is enabled,

• Fujitsu CW35 Series, Copyright This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders. This publication is provided for informational purposes only. The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the r

• Fujitsu CW35 Series, 42 3 Award BIOS Setup Utility 3.1 The Basic Input/Output System The Basic Input/Output System (BIOS) is a program that takes care of the basic level of communication between the processor and peripherals. In addition, the BIOS also contains codes for various advanced features found in this system board. This chapter explains the Setup Utility for the Award BIOS. After you power up the system, the BIOS message appears on the screen and the memory count begins. After the memory test, the following message will appear on the screen: Press DEL to enter setup If the message disappears before you respond, restart the system or press the Reset button. You may also

• 51 3 Award BIOS Setup Utility SDRAM RAS Precharge Time If there is insufficient number of cycles for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain data. System BIOS Cacheable When this option is enabled, accesses to the system BIOS ROM addressed at F0000H-FFFFFH are cached, provided that the cache controlle

• Fujitsu CW35 Series, Introduction 1 6 1.1 Features and Specifications 1.1.1 Features Chipset  Intel ® 810-E (CW35-E) Intel ® 810 DC-100 (CW35-D) Intel ® 810 (CW35-S) Intel ® 810-L (CW35-L) Processor The system board is equipped with Socket 370 for installing an Intel Celeron TM processor that is packaged in PPGA (Plastic Pin Grid Array). It is also equipped with a switching voltage regulator that automatically detects 1.30V to 2.05V.  Future Pentium ® III FCPGA 133MHz FSB processor (CW35-E)  Future Pentium ® III FCPGA 100MHz FSB processor  Celeron TM PPGA (300A-533MHz) 66MHz FSB processor System Memory  16MB to 256MB/512MB memory using unbuffered DIMMs with 64M

• Fujitsu CW35 Series, C 84 Troubleshooting Hard Drive Hard disk failure. 1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS. 2. If the system is configured with two hard drives, make sure the bootable (first) hard drive is configured as Master and the second hard drive is configured as Slave. The master hard drive must have an active/bootable partition. Excessively long formatting period. 1. If your hard drive takes an excessively long period of time to format, it is likely a cable connection problem. However, if

• 58 3 Award BIOS Setup Utility PWR Lost Resume State Keep Off When power returns after an AC power failure, the systems power is off. You must press the Power button to power-on the system. Turn On When power returns after an AC power failure, the system will automatically power-on. Last State When power returns after an AC power failure, the system will return to

• Fujitsu CW35 Series, 44 3 Award BIOS Setup Utility IDE Primary/Secondary Master/Slave If you wish to define your own drive type manually, select Manual. The drive type information should be included in the documentation from your hard disk vendor. If you select Auto, the BIOS will auto-detect the HDD & CD-ROM drive at the POST stage and show the IDE for the HDD & CD-ROM drive. If a hard disk has not been installed, select None. Capacity Displays the approximate capacity of the disk drive. Usually the size is slightly greater than the size of a formatted disk given by a disk checking program. Access Mode For hard drives larger than 528M

• Fujitsu CW35 Series, 2 Hardware Installation 29 The system board supports Enhanced IDE or ATA-2, ATA/33 or ATA/66 hard drives. We recommend that you use hard drives from the same manufacturer. In a few cases, drives from two different manufacturers will not function properly when used together. The problem lies in the hard drives, not the system board. Important: If you encountered problems while using an ATAPI CD-ROM drive that is set in Master mode, please set the CD-ROM drive to Slave mode. Some ATAPI CD-ROMs may not be recognized and ca

• Fujitsu CW35 Series, 73 4 Supported Softwares 4.2 Hardware Doctor Utility The system board comes with the Hardware Doctor utility contained in the provided CD. This utility is capable of monitoring the systems health conditions and allows you to manually set a range (Highest and Lowest Limit) to the items being monitored. If the settings/ values are over or under the set range, a warning message will pop- up. The utility can also be configured so that a beeping alarm will sound whenever an error occurs. We recommend that you use the Default Setting which is the ideal setting that would keep the system in good working condition

• Fujitsu CW35 Series, 49 3 Award BIOS Setup Utility OS Select for DRAM > 64MB This item allows you to access the memory that is over 64MB in OS/2. The options are: Non-OS2 and OS2. HDD S.M.A.R.T. Capability The system board supports SMART (Self-Monitoring, Analysis and Reporting Technology) hard drives. SMART is a reliability prediction technology for ATA/IDE and SCSI drives. The drive will provide sufficient notice to the system or user to backup data prior to the drives failure. The default is Disabled. If you are using hard drives that support S.M.A.R.T.

• Fujitsu CW35 Series, 54 3 Award BIOS Setup Utility Auto The BIOS will automatically set the system according to your hard disk drives timing. 0-4 You can select a mode that matches your hard disk drives timing. Caution: Do not use the wrong setting or you will have drive errors. IDE Primary Master/Slave UDMA and IDE Secondary Master/ Slave UDMA These categories allow you to set the Ultra DMA in use. When Auto is selected, the BIOS will select the best available option after checking your hard drive or CD-ROM. Auto The BIOS will automatically detect the settings for you. Disabled The BIOS will not detect these categories. USB Control

• Fujitsu CW35 Series, 2 Hardware Installation 21 Nomenclature BIOS - AC97 Audio : Refers to the AC97 Audio field in the Integrated Peripherals submenu. BIOS - AC97 Modem : Refers to the AC97 Modem field in the Integrated Peripherals submenu. Onboard audio (primary) No card in AMR or PCI/ISA slot JP7: enable BIOS - AC97 Audio: auto + = 1. Primary audio riser in AMR slot JP7: disable BIOS - AC97 Audio: auto = 2. Onboard audio (primary) Secondary audio riser in AMR slot JP7: enable BIOS - AC97 Audio

• Fujitsu CW35 Series, 50 3 Award BIOS Setup Utility 3.1.3 Advanced Chipset Features This section gives you functions to configure the system based on the specific features of the chipset. The chipset manages bus speeds and access to system memory resources. These items should not be altered unless necessary. The default settings have been chosen because they provide the best operating conditions for your system. The only time you might consider making any changes would be if you discovered some incompatibility or that data was being lost while using your syste

• Fujitsu CW35 Series, 2 38 Hardware Installation 2.9.19 DIMM/PCI Standby Power LED DIMM Standby Power LED This LED will light when the system is in the power-on or Suspend mode. It will not light when the system is in the Soft-Off state. PCI Standby Power LED This LED will light when the system is in the power-on, Soft-Off or Suspend mode. 3.3VSB Standby for PCI (jumper J18) The default setting of jumper J18 is On. It provides 3.3VSB Standby power to the PCI slots. If you are using a PCI modem card that does not comply to the PCI 2.2 specification, please set this jumper to Off. The PCI Standby Power LEDs light will subsequently turn off. Important: Lighted LEDs serve as a reminder that you

• Fujitsu CW35 Series, 52 3 Award BIOS Setup Utility Onboard Display Cache Setting The fields in this section are selectable only when you are using the CW35-E or CW35-D system board. CAS# Latency This field is used to select the local memory clock periods. The options are 2 and 3. Paging Mode Control This field is used to select the paging mode control. The options are Open and Close. RAS-to-CAS Override This field is used to select the display cache clock periods control. The options are by CAS# LT and Override(2). RAS# Timing This field controls RAS# active to Protegra, and ref

• Fujitsu CW35 Series, 2 Hardware Installation 41 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 HD-LED (Primary/Secondary IDE LED) G-LED (Green LED) ATX-SW (ATX power switch) G-SW (Green switch) RESET (Reset switch) SPEAKER (Speaker connector) KEYLOCK (Power/Standby LED and Keylock connector) Pin Assignment HDD LED Power HDD N. C. Green LED Power Green N. C. PWRBT Ground N. C. SMI Ground N. C. H/W Reset Ground N. C. Speaker Data N. C. Ground Speaker Power N. C. LED Power (+) N.C. LED Power (-) or Standby Signal Keylock Ground Use pins 21-23 for the Power/ Standby LED. S1 (POS - Power On Suspend) state, it will blink every second. When the

Related Products and Documents (Motherboard):

Comparable Devices:

Similar Resources:

• Dell OptiPlex GX270 (106 pages) www.dell.com | support.euro.dell.comDell™ OptiPlex™ SystemsSetup and Quick Reference GuideGuide de configuration et de référence rapideSetup- und SchnellreferenzhandbuchGuida di installazione e consultazione rapidaGuía de instalación y de referencia rápidaKurulum ve Hızlı Başvuru KılavuzuModels DHS, DHP, and DHM …

• Intersil ISL72813SEHEV1Z (17 pages) 1ISL72813SEHEV1Z Evaluation Board User GuideDescriptionThe ISL72813SEHEV1Z evaluation board was designed to provide a quick and easy method for evaluating the ISL72813SEH, 32-channel driver circuit IC. This device is a unique IC. To use this evaluation board properly requires a thorough knowledge of the operation of the IC. Refer to the ISL72813SEH datasheet …

• ASROCK N68-S3 FX (154 pages) 11111ASRock N68-GS3 FX / N68-S3 FX MotherboardEnglishEnglishEnglishEnglishEnglishCopyright Notice:Copyright Notice:Copyright Notice:Copyright Notice:Copyright Notice:No part of this installation guide may be reproduced, transcribed, transmitted, or trans-lated in any language, in any form or by any means, except duplication of documen-tation by the purchas …

• Texas Instruments TPS54336AEVM-010 (20 pages) 1SLVUB77–July 2017Submit Documentation FeedbackCopyright © 2017, Texas Instruments IncorporatedTPS54336AEVM-010 3-A Regulator Evaluation ModuleUser's GuideSLVUB77–July 2017TPS54336AEVM-010 3-A Regulator Evaluation ModuleThis user's guide contains background information for the TPS54336A as well as support documentationfor the TPS54336AEVM-010 …

• ASROCK PV530-ITX (94 pages) 11111ASRock PV530-ITX MotherboardEnglishEnglishEnglishEnglishEnglishCopyright Notice:Copyright Notice:Copyright Notice:Copyright Notice:Copyright Notice:No part of this installation guide may be reproduced, transcribed, transmitted, or trans-lated in any language, in any form or by any means, except duplication of documen-tation by the purchaser for backup …

• MSI MS-7140 (80 pages) i FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequ …

Comments, Questions and Opinions: