Fujitsu IP-900E Hardware User's Manual

Text of Fujitsu IP-900E User Guide:

• Fujitsu IP-900E, Chapter 3 Operation Instructions IP-900E/IP-900D series 36 3.2 Device Settings and Operation ■Setup Procedure The setup procedure is shown below. See Software User’s Guide for the procedure of the software installation and the each setting. ■Web browser recommended The recommended web browser is as follow. - Internet Explorer 6.0 SP2 or later 3.2 Connect IP-900 and PC using UTP cable - Check if IP-900 is disconnected to user’s network. - Connect using UTP cable. - When connect through LAN port, the default IP address and subnet mas

• Fujitsu IP-900E, Chapter 2 Installation and Connection IP-900E/IP-900D series 24 2.2.2 Connection to power source IP-900E/IP-900D series operation requires a power supply of 100-240 VAC. Insert the power cord with the standard two-prong plug with ground into the inlet connector. The power cord is not supplied with the device. Procure it separately. Figure Power cord connection AC cord clamp Insert the AC cord clamp into the AC cord clamp hole and fix the power cord as

• Chapter 3 Operation Instructions IP-900E/IP-900D series 39 3.3.2 Log Click Log in the left frame of the browser to display the log information page in the right frame of the browser, where you can check alarm log information on the IP-900E/IP-900D series. Clicking in the right frame deletes all log information. * Up to 1,000 log items can be saved. Log items exceeding

• Fujitsu IP-900E, Chapter 2 Installation and Connection This chapter describes conditions for IP-900E/IP-900D series installation and explains how to connect it to peripheral devices. Figures described in this chapter are used IP-900E as a sample. 2.1 Installation Conditions······························································ 13 2.2 Power Supply System Connections ······································ 23 2.3 Audio and Vide

• Fujitsu IP-900E, Chapter 4 Cable specifications IP-900E/IP-900D series 51 or or or or or or 220V (Class I) IEC 60320-1 (IEC C-13) Rated 12A, 250V Comply with KSC3304. Type VCTF cross section area 1.25 (0.50 or 1.00 or 2.00) square mm 3-Conductors (Single phase;2-current carrying conductors & ground) Comply with KSC8305. Rated 12A, 250V Korea 220V (Class II) IEC 60320-1 (IEC C-13) Rated 3A, 250V Comply with KSC3304. Type VCTFK cross section area 1.25 (0.50 or 0.75 or 1.00 or 2.00) square mm 2-Conductors Comply with KSC8305. Rated 12A, 250V Note: *l. Be sure that the detachable proper Supply cord has the approval of the

• Fujitsu IP-900E, IP-900E/IP-900D series vi SAFETY PRECAUTIONS List of important warnings The table below contains a list of important warning indications. Work type Warning Normal use Possibility of electric shock and fire If an excessive heat, smoke, an abnormal odor or an unusual noise is coming from the device, immediately set its power switch to OFF and remove the power cord plug from the power receptacle. Then, contact a Fujitsu Service Center. This indicates a hazardous situation that could lead to fire and electric shock. Possibility of electric shock and fire If f

• Fujitsu IP-900E, Chapter 3 Operation Instructions IP-900E/IP-900D series 37 This section briefly explains the basic functions of the setup pages. 3.2.1 Maintenance page Clicking the Settings, Log or Software management menu in the left frame of the browser displays the corresponding device setting page so that you can set or display items. 3.2.2 Reboot Clicking the button displayed in the left frame of the browser reboots the device. When you click the button, the following dialog box shown below appears for confirmation. Click OK to reboot.

• Fujitsu IP-900E, Chapter 5 Troubleshooting IP-900E/IP-900D series 63 5.3.2 Change of maintenance parts (Maintenancer only) If there is no improvement of situation after checking and dealing with referring Section 5.1, “Help Information,” change the hardware following the procedure below. The maintenance unit of this product is the whole equipment. When failure, please change whole equipment for the change of the maintenance parts. Please refer Section 2.6, “CF card insertion and removal,” for the respective maintenance.

• Fujitsu IP-900E, IP-900E/IP-900D series vii Work type Warning Installation Possibility of electric shock and fire Do not install the device in the following places because using it there may cause a fire or electric shock: • Extremely dusty or dirty place • Wet or humid location • Hot location, such as a place where the device is exposed to direct sunlight or is near heating equipment • Near products (e.g., speakers) that generate a strong magnetic field • Location where the temperatur

• Fujitsu IP-900E, IP-900E/IP-900D series i USING IP-900E/IP-900D series SAFELY Handling of This Manual The manual contains important information regarding the safe use of IP-900E/IP-900D series. Read it thoroughly before operating this device. Make sure that users of the device read and understand thoroughly all safety precautions contained in the manual. Keep this manual in a safe and convenient location for quick reference. Fujitsu makes every effort to prevent users and bystanders from injury and to prevent property damage. To ensure no

• Chapter 5 Troubleshooting IP-900E/IP-900D series 55 5.1 Help Information If a problem is found in device operation, take recommended action described in the table below, according to the applicable conditions. If the action does not solve the problem, contact a service representative. Possibility of electric shock Contact your system administrator before checking the volt

• Fujitsu IP-900E, Chapter 1 Preparations This chapter describes the checks that are required before the start of IP-900E /IP-900D series operation. 1.1 Main Features ············································································ 3 1.2 Components··············································································· 4 1.3 Basic Application Examples ······················································· 5 1.4 Part Names ···

• Fujitsu IP-900E, Appendix IP-900E/IP-900D series 72 Name Specifications Remarks LAN interface [10BASE-T] System standard: IEEE802.3 Transmission clock: 10Mbit/s±10000ppm(±0.01%) Load impedance: 100Ω Transmission coding: Manchester coding [100BASE-TX] System standard: IEEE802.3u Transmission clock: 125 Mbit/s±5000ppm(±0.005%) Load impedance: 100Ω Transmission codin g : 4B5B Connector name 10/100 BASE RJ-45 Pin number Signal name Remarks 1 2 3 4 5 6 7 8 TD+ TD- RD+ N.C. N.C. RD- N.C. N.C. Trans. data+ Trans. data- Reciv. data+ - - Reciv. d

• Fujitsu IP-900E, Chapter 2 Installation and Connection IP-900E/IP-900D series 16 (6) Install the mounting fittings on IP-900E/IP-900D series using six same screws(M4). (7) Install IP-900E/IP-900D series on 19” rack using four screws (M5).

• Fujitsu IP-900E, Appendix IP-900E/IP-900D series 67 A.1 Appearance The appearance of IP-900E/IP-900D series is shown below. A.1 300 /ACT RDY PWR ALM IN DWN OPT 100M LINK RDY PWR ALM IN DWN OPT MNT FG /ACT 100M LINK LR 100-240V 210 42

• Fujitsu IP-900E, IP-900E/IP-900D series iii PREFACE Thank you for purchasing the IP-900E/IP-900D series. IP-900E/IP-900D series are the video transmission unit with the H.264 encoding technology which performs the high compression ratio, and transmits the SD (Standard Definition) /HD (High Definition) video and audio signals in real time through even the optical IP network like FTTH. (*1) IP-900E has functions that encodes SD/HD video signals from a SD/HD camera or similar device and distributes it across the networ

• Fujitsu IP-900E, Appendix IP-900E/IP-900D series 78 (1) Preparations 1) Check the system configuration Check the entire system configuration. 2) Check the units and cables to be connected to the device Check the units to be connected to the device, cables that have to be procured, and installation conditions. 3) Tools and measuring instruments necessary for work: • Digital multimeter • General-purpose tools (2) Environment check 1) Ambient air temperature, humidity and power supply M

• Glossary and Index Glossary ····························································································· 83 Index································································�

• Chapter 2 Installation and Connection IP-900E/IP-900D series 14 (2) Check all cables disconnected. (3) Connect the first device with the coupling fittings using six same screws (M4). (4) Connect the second device with the coupling fittings using six same screws (M4).

• Fujitsu IP-900E, Appendix IP-900E/IP-900D series 76 A.3 Preparations for Installation Work This section contains notes and describes check items for installation work. A.3.1 Scope of installation work For details about the scope of installation work, see Section 4.1, “Installation Preparations.” A.3.2 Unpacking and device check Unpack and check the device as follows: • During unpacking, carefully handle the device so as not to apply shock to it or damage its appearance. • Make sure that the device and accompanying package are n

• Fujitsu IP-900E, Appendix IP-900E/IP-900D series 74 (IP-900E only) Name Specifications Remarks HDMI input Signal format Input impedance Maximum length connector ：TMDS ：50 ohms ±10% ：-------- ：19PIN Type A Length of the attested HDMI cable is pretermission. The unattested cable can't be used. Connector name HDMI IN HDMI 19 pin Type A Pin number Signal name Remarks 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 TMDS DATA2 + TMDS DATA2 SHIELD TMDS DATA2 - TMDS D

• Fujitsu IP-900E, Appendix IP-900E/IP-900D series 73 Name Specifications Remarks Data interface (RS-232C) No. of CH Signal system Connection Bit rate Data length Parity Stop bit : 1 ch : Asynchronous : DTE : 1200, 2400, 4800，9600, 19200, 38400 bps :7/ 8 : NONE/ODD/EVEN : 1/2 RS-232C Connector name RS-232C D-sub 9 pin(male) Pin number Signal name Remarks 1 2 3 4 5 6 7 8 9 CD RD SD DTR (ER) SG DSR (DR) RTR (RS) CTS (CS) RI Carrier Detect Receive Data Send Data Da

• Fujitsu IP-900E, Chapter 4 Cable specifications IP-900E/IP-900D series 48 (6) RS-232C cable ○ ○ ○ ○ ○ ○ ○ ○ <External device side> Front view <IP-900E> （DTE） RS-232C DTE ○ <External device> (DTE) D-sub 9 pin (female) 01 02 03 04 05 06 07 08 09 ○ ○ ○ ○ ○ ○ ○ ○ ○ D-sub 9 pin (male) D-sub9 (female) #4-40 retainer screw SG DSR(DR) RTS(RS) CTS(CS) CD RD SD DTR(ER) RI SG DSR(DR) RTS(RS) CTS(CS) CD RD SD DTR(ER) RI ○ ○ ○ ○ ○ ○ ○ ○ <IP-900E> （DTE） RS-232C DCE ○ <External device> (DCE) D-sub 9 pin (female) 01 02 03 04 05 06 07 08 09 ○ ○ ○

• Fujitsu IP-900E, Glossary and Index IP-900E/IP-900D series 86 Index １ 1000BASE-T ................................................. 3, 29 100-240VAC.................................... 3, 26, 69, 73 100-240VAC power cord.................................. 50 100BASE-TX ......................................... 3, 29, 72 10BASE-T .............................................. 3, 29, 72 Ａ Alarm LED ..................................................... 6, 8 Alarm LED lamp .............................................. 61 Appearance..............

More Instructions:

Fujitsu IP-900E Hardware user's manual 15-04-2024 116

DOWNLOAD

Related Products and Documents (Network Hardware):

Comparable Devices:

Similar Resources:

• Security Camera King NVR-LT-128 (106 pages) 128ch NVR User's ManualNVR-LT-1283MPResolution1yr WarrantyThis is our highest end NVR and probably the highest end NVR on the market. With this NVR you can manage and record up to 128 IP cameras. Of course, all of our IP cameras are compatible, but you can also use other ONVIF compliant IP cameras with it. This NVR is in a 3U server case. It can hold up …

• HP MSA 2040 (2 pages) HP Chassis ReplacementInstructionsAbstractThis document details procedures for replacing a failedcontroller enclosure and drive enclosure chassis. Whenreplacing a chassis, all modular components are removedfrom the failed chassis and then installed in the replacementchassis.© Copyright 2009, 2013 Hewlett-Packard Development Company, L.P.Printed in the US*59 …

• Moxa Technologies AirWorks AWK-5222 (100 pages) Moxa AirWorks AWK-5222 User’s Manual First Edition, June 2009 www.moxa.com/product © 2009 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. …

• Cisco MX400 (5 pages) MX400 Installation GuideThis document describes how to install and set up the MX400 security appliance. Additional reference documents areavailable online at: www.meraki.com/library/products.MX400 OverviewThe Meraki MX400 is an enterprise security appliance designed for fordistributed networks that require remote administration. It is ideal fornetwork admini …

• Teledyne Lecroy PCI Express 5.0 M.2 M-Key Interposer (12 pages) Introduction The Teledyne LeCroy PCI Express 5.0 M.2 M-Key Interposer CrossSync PHY Capable, which is used with Summit T5 Protocol Analyzers, enables PCIe bus traffic between a system board or tablet and a M.2 connector on a PCIe M.2 device to be monitored, captured, and recorded for protocol analysis. The Gen5 M.2 Interposer (CrossSync PHY capable) wil …

• Cisco Nexus 93180LC-EX (12 pages) Installing the Switch Chassis•Safety, page 1•Installation Options with Racks and Cabinets, page 2•Airflow Considerations, page 2•Installation Guidelines, page 2•Unpacking and Inspecting the Switch, page 3•Installing the Switch, page 4•Grounding the Chassis, page 9•Starting the Switch, page 11SafetyBefore you install, operate, or service the s …

Comments, Questions and Opinions: