Manualios.com

Fujitsu FLASH-CAN-100 Operation & User’s Manual

  • FLASH-CAN-100 Power Supply
  • mahizLrORRP7I
  • Operation & User’s Manual
  • PDF / Adobe Acrobat Reader
  • 20

Fujitsu FLASH-CAN-100 Manual Online:

4.9, 2339 votes
Fujitsu FLASH-CAN-100 User Manual
Fujitsu FLASH-CAN-100 User Guide
Fujitsu FLASH-CAN-100 Online Manual

Text of Fujitsu FLASH-CAN-100 User Guide:

  • Change even page title here Revision History UG-900001-32 - 2 - © Fujitsu Microelectronics Europe GmbH Revision History Date Version Issue 07.12.98 V1.0 P14,P16 connected to JP7, JP8 (RS232 interface for MB90F594A) must be changed 07.12.98 V1.0 Jumper on JP10, JP9 Pin2+3 must be changed to Pin 1+2 to connect to UART1 07.12.98 V1.2 Silk-Plot: Version number m

  • Fujitsu FLASH-CAN-100, Change odd page title here Revision History © Fujitsu Microelectronics Europe GmbH - 3 - UG-900001-32 Date Version Issue 23.08.99 V2.2 Table 2. MB90F543 UART0 is wrong – it must be UART1 17.04.00 V2.3 Table 2 corrected now 17.04.00 V2.3 Chapter 1.1. Regarding connectivity problems added. FLASH-CAN-100P-M06 is available again 09.01.01 V2.4 Support added for MB90F42x series 25.01.01 V2.5 Support for MB90F546G/GS and MB90F548G/GS series added, Description of Connector JP11 added 19.09.01 V2.6 Support for MB90440G series added, new disclaimer added 05.10.01 V2.7 New disclai

  • Fujitsu FLASH-CAN-100, Change even page title here Warranty and Disclaimer UG-900001-32 - 4 - © Fujitsu Microelectronics Europe GmbH Warranty and Disclaimer To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts its warranties and its liability for the FLASH-CAN-100P-M06 Board and all its deliverables (eg. software include or header files, application examples, target boards, evaluation boards, engineering samples of IC’s etc.), its performance and any consequential damages, on the use of the Product in accor

  • Fujitsu FLASH-CAN-100, Change odd page title here Contents © Fujitsu Microelectronics Europe GmbH - 5 - UG-900001-32 Contents REVISION HISTORY............................................................................................................ 2 WARRANTY AND DISCLAIMER ......................................................................................... 4 CONTENTS .......................................................................................................................... 5 1 OVERVIEW................................................................................................................

  • Fujitsu FLASH-CAN-100, Change even page title here Chapter 1 Overview UG-900001-32 - 6 - © Fujitsu Microelectronics Europe GmbH 1 Overview 1.1 Abstract This user guide describes the basic features of the new FLASH-CAN-100P-M06/FLASH- CAN2-100P-M06 board. This board can be used with almost all our 16LX microcontroller series supporting the FPT-100P-M06 package. 1.2 Introduction The "Flash/CAN100"-board was developed in order to support customers and allow a fast software design start. Fujitsu emulators require

  • Fujitsu FLASH-CAN-100, Change odd page title here Chapter 2 Features © Fujitsu Microelectronics Europe GmbH - 7 - UG-900001-32 2 Features < a new 100-pin socket adapter for better connectivity < 7-14V unstabilized external DC power supply possible < 5V and 3.7V internal power supply available < two high-speed CAN drivers < one RS232 interface < two identical pin connectors for all MCU pins < optional sub-clock < RST, HST push-button < 8 User-LEDs < external reset via RS232 < Flash-Programming Software for PC’s The target board wi

  • Fujitsu FLASH-CAN-100, Change even page title here Chapter 3 Supported Microcontroller Series UG-900001-32 - 8 - © Fujitsu Microelectronics Europe GmbH 3 Supported Microcontroller Series The target board was designed to work with many microcontrollers from the F²MC-16LX family. As it allows the programming of blank flash devices and supports high speed CAN interfaces, this board is ideal as a test at design start. The following microcontroller series can be used with this board: < MB90420G = MB90V420G, MB90F428GA/GB/GC etc. < MB90435 = MB90V540, MB90F437, MB90F438, MB90F439 etc. < MB90440G = MB90V440G, MB90F443G

  • Fujitsu FLASH-CAN-100, Change odd page title here Chapter 4 Deliverables © Fujitsu Microelectronics Europe GmbH - 9 - UG-900001-32 4 Deliverables "FLASH-CAN-100P-M06"/"FLASH-CAN2-100P-M06" will be delivered with: < the Flash/CAN100 board itself < two 50pin socket connectors < power supply connector < MB90F598 - 128KB flash microcontroller < 11 Jumper < 1 socket adapter cover < documentation < Flash programming utility – floppy disc For software add-ons please contact your local technical support team for the latest software release or Flash-Programming tools.

  • Fujitsu FLASH-CAN-100, Change even page title here Chapter 5 Configuration of the Evaluation-Board UG-900001-32 - 10 - © Fujitsu Microelectronics Europe GmbH 5 Configuration of the Evaluation-Board The board is configured to work with the MB90F598 microcontroller. In order to set up the board follow these steps: 1. disconnect power supply disconnected ! 2. Set jumper JP1 to provide Vcc, i.e. 5V to the board 3. If case one is connecting this board to an emulator, it is recommended to set jumper JP2 in order to provide 3.7V to the internal core. 4. Please set the mode pins 1-3 on S3 ac

  • Fujitsu FLASH-CAN-100, Change odd page title here Chapter 5 Configuration of the Evaluation-Board © Fujitsu Microelectronics Europe GmbH - 11 - UG-900001-32 7. Select the appropriate UART interface for the microcontroller you are using by setting jumper JP7-JP10. 8. Please use 1:1 cable for PC-connection. Notes: < Pixx on the silk plot stands for Pinxx, i.e. the pin number. e.g. for the MB90F598, set JP10 and JP9 to connect Pin 1 and 2 in order use UART 1 < MB90425, MB90470, MB90480 and MB90580 series are not supported by jumpers. Please make handwired conne

  • Fujitsu FLASH-CAN-100, Change even page title here Chapter 5 Configuration of the Evaluation-Board UG-900001-32 - 12 - © Fujitsu Microelectronics Europe GmbH 5.1 Modifications for use with MB90470 / MB90480 series Some modifications have to be done in order to use the FLASH-CAN-100P Board together with a MCU of the MB90470 / MB90480 series: 1. Check that U6 is MAX3232CPE 2. Change R6 470 => 390 Ohm. Check that output voltage of U3 is 3.3V (JP2) 3. Disassemble C10 (100nF) 4. Connect J4- Pin 27 to JP10- Pin

  • Fujitsu FLASH-CAN-100, Change odd page title here Chapter 5 Configuration of the Evaluation-Board © Fujitsu Microelectronics Europe GmbH - 13 - UG-900001-32 5.1.1 Schematic of the modifications for MB90470 / MB90480

  • Fujitsu FLASH-CAN-100, Change even page title here Chapter 6 Using the Asynchronous Boot-Loader UG-900001-32 - 14 - © Fujitsu Microelectronics Europe GmbH 6 Using the Asynchronous Boot-Loader The asynchronous boot-loader SW from Fujitsu can be used to program a blank flash microcontroller. This tool is available on the floppy disc. The following additional steps to chapter 5 need to be taken to set up the hardware (power supply disconnected!): 1. Place the flash microcontroller in its socket (observe pin no. 1 position). 2. Set DIP switch (SW3) : 1,5,7,8 ON 2,3,4,6 OFF MB90470 / MB90480 series only: 1,5

  • Change odd page title here Chapter 7 Connectors © Fujitsu Microelectronics Europe GmbH - 15 - UG-900001-32 7 Connectors 7.1 Power connector (X1) The following figure shows the power connection jack X1. This connector is used to connect an external unregulated DC power supply voltage (9V-12V DC) to the evaluation board. Connector X1:

  • Change even page title here Chapter 7 Connectors UG-900001-32 - 16 - © Fujitsu Microelectronics Europe GmbH 7.4 UART (X4) One 9-pin D-Sub female connectors are used for the serial interface (UART). TXD is the transmit output, RXD is the receive input. The DTR signal can be used to generate a reset. Please use 1:1 cable for PC-connection. Connector X4:

  • Fujitsu FLASH-CAN-100, Change odd page title here Chapter 10 Related Products © Fujitsu Microelectronics Europe GmbH - 19 - UG-900001-32 10 Related Products < FLASH-CAN-100P-M06 Evaluation-board according to this user guide < MB2132-457 Probe cable for socket: Yamaichi IC149-100-x14-y5 Yamaichi: http://www.yamaichi.de < FLASH-CAN2-100P-M06 New Evaluation board according to this user guide < MB2132-464 Probe cable for socket: Tokyo Eletech: NQPack100rb / HQPack100rb179 Tokyo Eletech: http://www.tetc.co.jp/nq/e_nq_draw.htm < MB2141A/B Emulator debugger main unit < MB2145-507 Emulation POD < MB90Vxxx Evaluation chip (please refer to chapter 3) <

  • Fujitsu FLASH-CAN-100, Change even page title here Chapter 11 Information in the WWW UG-900001-32 - 20 - © Fujitsu Microelectronics Europe GmbH 11 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://www.fme.gsdc.de/gsdc.htm Memory products: Flash, SDRAM and FRAM http://www.fme.fujitsu.com/products/memory/index1.html Linear Products: Power Management, A/D and D/A Converters http://www.fme.fujitsu.com/products/linear/start.html Media Products: SAW filters, acoustic resonators and VCOs

Related Products and Documents (Power Supply):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 iHome iH36 Operation & user’s manual ihome/ih36-18S.pdf 29 Nov 2023 22
2 Parkinson Cowan CALOR Sonata 50 Owners and installation instructions parkinson-cowan/calor-sonata-50-1HW.pdf 16 Sep 2022 40 2.23 Mb
3 Hotpoint WMA62 Installation and user instructions manual hotpoint/wma62-M3P.pdf 05 Nov 2022 28 0.44 Mb
4 ZyXEL Communications Prestige 642 Operation & user’s manual zyxel-communications/prestige-642-P9M.pdf 24 Nov 2022 155 0.93 Mb
5 Life Fitness C7i Assembly instructions manual life-fitness/c7i-2XN.pdf 09 Dec 2023 9
6 BlueRhino GGC1643B Owner's manual bluerhino/ggc1643b-TET.pdf 21 Apr 2023 32

Similar Resources:

  • Trivum

    RP321

    (2 pages)
    Quick Installation GuideRP321AN: 301023Connection example:Connection examples with trivum Audio Extenders:🛒 All trivum products are available in our online shop www.trivum.comArticle Numbers:Technical DataRequired components for installation:• 24 V DC power supply, at least 4A (e.g. PS24/100 4.2A by trivum AN: 500023)• ethernet cable• network wit …
  • TekPower

    TP-3005D

    (10 pages)
    1CONTENTS: 1. SAFETY PRECAUTION AND PROCEDURES................................................................2 1.1 BEFORE USE.............................................................................................................................. 3 1.2 DURING USE......................................................................................... …
  • Sears

    200

    (8 pages)
    OPERATOR’S MANUAL®Ultra-Slim Travel Inverter 120 Converts 12V DC Power to 110V AC Household Electrical Power + USB (5V) CAUTION:Read all Safety Rules and Operating Instructions, and follow them with each use of this product.Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.Model No. 200.7152000-99-000860/0808 …
  • Datexel

    DAT 411

    (2 pages)
    Via monte Nero, 40/B – 21049 TRADATE (VA) ITALY Phone: +39 (0)331841070 Fax:+39 (0)331841950 - e-mail:[email protected] - www.datexel.itDouble output power supply unit DAT 411DAT 411GENERAL DESCRIPTIONThe power supply unit DAT 411 is designed to provide two not regulated isolated outputs to power the DATEXEL devices like transmitters and low current c …
  • DEV

    5071

    (69 pages)
    Customer Documentation DEV 5071 High Power DC Supply DEV Systemtechnik GmbH Grüner Weg 4A 61169 Friedberg GERMANY Tel: +49 6031 6975 100 Fax: +49 6031 6975 114 [email protected] www.dev-systemtechnik.com Revision: 2017-12-19 DEV 91-0073-C …
  • Eaton

    Eaton 9140

    (365 pages)
    Powerware SeriesEaton 9140 (9910-E82/E83) UPSInstallation Guide for IBM Applications®Guide d'Installation Onduleur pour Applications IBMUSV Installationsanleitung für IBM-AnwendungenGuida all'Installazione dell'UPS per le Applicazioni IBMGuía de Instalación del SIE para Aplicaciones de IBM® …

Comments, Questions and Opinions: