Fujitsu Solaris 10 Hardware Platform Manual

Text of Fujitsu Solaris 10 User Guide:

• Fujitsu Solaris 10, 24 ok 4. Search the device path to the secondary LAN port with a show-nets command from ok prompt of a client system. ok show-nets <Return> Example ok show-nets a) /pci@83,2000/FJSV,pwga@1 b) /pci@1f,4000/FJSV,pgsb@4 q) NO SELECTION Enter Selection, q to quit: 5. From ok prompt of a client system, please start a client system using the secondary LAN port. ok boot /pci@83,2000/FJSV,pwga@1 <Return> 6. Install the Solaris 4.3.2.6 Configuring VLAN interface 4.3.2.6.1 IEEE 802.1Q TagVLAN The outline about a VLAN interface and directions required in order to setup VLAN interfa

• Fujitsu Solaris 10, 1 Preface Solaris™ Operating System is described as Solaris in this manual. Purpose This manual provides notes necessary after installing the Solaris 10 on PRIMEPOWER. Intended Readers This manual is intended for system administrators who install Solaris™ Operating System (Solaris) and operate it. Readers are expected to have the basic knowledge of a system administrator. Organization This manual is organized as follows: z Chapter 1 Notes after the Installation This chapter describes post-installation notes. z Chapter 2 Backup

• Fujitsu Solaris 10, 5 7. Press the Eject button on the diskette drive unit, then eject the diskette. WARNING messages of se driver When a serial port receives a lot of data, such as when a large amount of text is pasted on a console screen connected to a serial port, the console message "seN: Buffer overrun" (N means an instance number of se driver) will be displayed and the data will be lost. This is because the user process cannot read data fast enough. The size of data pasted on a console screen should be 1024 bytes or less at a time. Speed of reception depends on each user process. 1.2.3 Notes on PCI cards How to install PCI cards T

• 26 protocol. z Since PRIMECLUSTER GLS 4.1A20 or previous version do not correspond to a VLAN interface, please do not use VLAN interface with those. PRIMECLUSTER GLS 4.1A30 or later (only Fast switching mode or NIC switching mode) can use VLAN interface. z VLAN function can be used only in Solaris 8, Solaris 9 or Solaris 10. z In the environment where PRIMECLUSTER has

• Fujitsu Solaris 10, 1 Chapter 1 Notes after the Installation This chapter describes the post-installation notes. 1.1 PRIMEPOWER - Specific Notes 1.1.1 Modifications of Solaris OS (Patches, PTF, Program Local Fix) Only the modifications (patches, PTF, Program Local Fix, etc.) for PRIMEPOWER provided by FUJITSU LIMITED can be applied to existing PRIMEPOWER systems running Solaris OS software. Do not use patches provided by Sun Microsystems, Inc. on the World Wide Web or those provided by other vendors. Also be careful that you do not apply modifications (patches, PTF, Program Local Fix

• 33 Limitations and known bugs No Recommended actions Remarks Solaris Live Upgrade is not supported with RAID-1(mirror) Custom Jumpstart installation for mirror volumes using a profile that has filesys keyword of both original and target disk, will fail and the following error message will be shown at first boot after the installation. met

• Fujitsu Solaris 10, 7 5. Restart the Solstice Enterprise Agent (SEA) daemon. # /etc/init.d/init.snmpdx start<Return> 1.2.5 Other notes and bug information For other notes and bug information during the system operation, refer to the following document: z "Solaris 10 Release Notes " 1.3 Unsupported Features The following features described in Solaris OS manuals are not supported. Table 1.1 Unsupported features No. Description Alternative method Reference manual 1 The Suspend-Resume features cannot be used with PRIMEPOWER. None "Solaris Common Desktop Environment: User's Guide" in "So

• Fujitsu Solaris 10, 16 Example /etc/hostname6.fjgi*: Define the unique hostname (This sample named giga-v6): addif giga-v6/120 up Note: If you defined the hostname in hostname.fjgi* file, see the section "4.3.1.2 Defining Hostname" for detailed information. 3. To use the GigabitEthernet as an VLAN interface: See "4.3.2.6 Configuring VLAN interface", and after defining VLAN name, proceed with above 1 or 2 procedure. 4.3.1.2 Defining Hostname Defining an IP address with a unique hostname. 1. To use secondary LAN port as an IPv4 interface: Edit IPv4 address and hostname into the /etc/hosts file. Example /etc/ho

• Fujitsu Solaris 10, 34 Limitations and known bugs No Recommended actions Remarks Follow these instructions to remove a package. (For example SUNWabc) 1) Re-install the package to system. # pkgadd SUNWabc 2) Find out path name of SMF service manifest in the package. # grep SUNWabc /var/sadm/install/contents | \ grep /var/svc/manifest | awk '{ print $1 }' | grep xml /var/svc/manifest/system/abc.xml 3) Run the following command. # svccfg -s smf/manifest delpg {$prp_mfst} $prp_mfst strings must be specified by removing first “/” srting of the manifest path name with all “/”

• Fujitsu Solaris 10, 32 Limitations and known bugs No Recommended actions Remarks For growfs(1M), the following patch is required to be installed. 120254-02 or later SunOS 5.10: ufs Patch 5 Install the above patches. Solaris 10 3/05 and 1/06 only When using any of the following PGX cards and monitors, the display monitor does not enter standby mode if you haven’t logged on from CDE (Common Desktop Environment). z PGX frame buffer (X3660A) z PGX64 frame buffer (X3768A/A-A) z Second monitor (X7128A/AA/AJ, X7128B) To use PGX32 frame buffer (X3668A/A-A, X3668B/B-A/B-B), the following patches are required to be installed. 1192

• Fujitsu Solaris 10, 37 Limitations and known bugs No Recommended actions Remarks A /noautoshutdown file might be created at first boot after Solaris 10 installation. If /noautoshutdown file exists power management and power saving could be disabled. 30 Check for and remove /noautoshutdown file if you need to enable power management and power saving features. Patch installation may fail with the following error message when the patch binary is located in /(root) directory. # patchadd xxxxxx-xx Assertion failed: *a_gzPath != ‘\0’, file zones.c, l

• Fujitsu Solaris 10, 10 If you are restoring, use the dd(1M) command after booting from the Solaris OS CD/DVD to restore the slice unit. - If you back up slice 0, it will only be possible to restore to a disk having the same physical properties (disk space, number of cylinders) as the original. - Disk partition information such as the size of each slice will not be backed up. You must record this information separately. d. To back up a disk unit, use the dd(1M) command after booting from the Solaris OS CD/DVD.

• 6 7. Enter the Open Boot Environment. Some of the manuals attached to the card may instruct "Reboot your machine", which means to enter the Open Boot Environment with the following command. # /usr/sbin/shutdown -y -g0 -i0 <Return> 8. When the OK prompt is displayed, boot the system with the following command. ok boot -r <Re

• Fujitsu Solaris 10, 20 Parameter Status Meaning flow_control Read only 0 : None (Not doing flow_control) 1 : LocSend (Can transmit pause frame only) 2 : Rem (Can receive pause frame only) 3 : Sym (Can receive and transmit pause frame) cardtype Read only 0 : SX(PW008GE4) 1 : T(PRIMEPOWER250/450 secondary LAN port, PW008GE5/PW008QG1) instance Read and write Instance Number adv_10fdx_cap Read and write Setting of 10Mbps/FullDuplex 0 : Invalid 1 : Valid (Default) adv_10hdx_cap Read and write Setting of 10Mbp/HalfDuplex 0 : Invalid 1 : Valid (Default) adv_100fdx_cap Read and write Setting of 100Mbps/

• Fujitsu Solaris 10, 3 Also, the following messages are stored many times in XSCF log, too. The error messages can be ignored safely. SCF> show-error-logs <Return> ***** No.01/32 Date = 2008/09/16 09:47:00 SysDamage = ALARM(STOP) FaultDetect = OBP FaultCode = 260000FF DetailInfo = [BOOTB]Boot Block error ReplaceParts= --- Syslog msg = Detected hardware error 30C97830 260000FF 08071523 3615FFFF 5B424F4F 54425D42 6F6F7420 426C6F63 6B206572 726F7200 00000000 00000000 00000000 00000000 00000000 00000000 1.2 Solaris OS - Notes and Bug Information 1.2.1 The order of instanc

• 31 Chapter 5 Precautions This chapter explains necessary precautions. 5.1 Limitations and known bugs for Solaris This chapter explains limitations and known bugs for Solaris. Table 5.1 Limitations and known bugs for Solaris Limitations and known bugs No Recommended actions Remarks The following patches are required to be installed in the following order after installatio

• Fujitsu Solaris 10, 21 Parameter Status Meaning lp_10hdx_cap Read only Setting of link-partner 10Mbps/HalfDuplex, when link up with AutoNegotiation. 0 : Invalid 1 : Valid lp_100fdx_cap Read only Setting of link-partner 100Mbps/FullDuplex, when link up with AutoNegotiation. 0 : Invalid 1 : Valid lp_100hdx_cap Read only Setting of link-partner 100Mbps/HalfDuplex, when link up with AutoNegotiation. 0 : Invalid 1 : Valid lp_1000fdx_cap Read only Setting of link-partner 1000Mbps/FullDuplex, when link up wit

• Fujitsu Solaris 10, 35 Limitations and known bugs No Recommended actions Remarks "Internet (IP) Address” in “Workstation information” of CDE environment is shown with a IPv6 unicast address as “::FFFF:***.***.***.***”. 20 This problem is solved by the following patch. 119284-01 or later CDE 1.6: sdtwsinfo patch Solaris 10 3/05 only During system shutdown, some messages similar to the following might be displayed on the console. syslogd: /var/opt/FJSVmadm/evh/evh_pipe: Broken pipe NFS fsinfo failed for server xxxx: error 5 (RPC: Timed out) 21 Ignore the message. It has no impact on the system. ifconfig(1M)

• Fujitsu Solaris 10, 11 ok boot -s <Return> 2. Backup the file system with the ufsdump(1M) command. Example: Backup to the "/dev/rmt/0." # ufsdump 0ucf /dev/rmt/0 / <Return> 2.2.2 Restore of File System Unit When restoring the file system unit, the Solaris OS is booted from the Solaris 10 CD1 or Solaris 10 DVD. After booting Solaris OS, mount the disk to be restored temporarily, and then restore the file system unit. Follow the procedures below to restore each file system. After restoring, reboot the system. If using a new disk or a disk previously used for other purposes, create a boot block after creating

• Fujitsu Solaris 10, i Contents Chapter 1 Notes after the Installation ...................................................................................................................1 1.1 PRIMEPOWER - Specific Notes.....................................................................................................................................1 1.1.1 Modifications of Solaris OS (Patches, PTF, Program Local Fix).............................................................................1 1.1.2 Changing the date and time..................................................................................................................

• Fujitsu Solaris 10, 2 All other products or company names mentioned in this document are claimed as trademark and trade names by their respective companies. March, 2005 October 2009 Sixth Edition Notes z This manual may not be copied by any means without the express written permission of FUJITSU LIMITED. z FUJITSU LIMITED reserves the right to make changes to this manual without prior notice. All Rights Reserved, Copyright © FUJITSU LIMITED 2005-2009 All Rights Reserved, Copyright © PFU LIMITED 2005-2009

• Fujitsu Solaris 10, 14 restore the slice unit. - If you back up slice 0, it will only be possible to restore to a disk having the same physical properties (such as disk space and a number of cylinders) as the original. - Disk partition information such as the size of each slice will not be backed up. You must record the information separately. d. To back up the disk unit, use the dd(1M) command after booting from the Solaris OS CD/DVD. If you are restoring, use the dd(1M) command after booting from the Solaris OS CD/DVD to restore the disk unit. - The procedure divides the disk unit for back up,

• Fujitsu Solaris 10, 9 Chapter 2 Backup and Restore of System Disk (PRIMEPOWER1/200/250/400/450/600/65 0/850) This chapter explains the procedures to backup/restore the disk (hereafter called, the system disk) containing the Solaris OS software. 2.1 Types of Backup Procedures Backup of the system disk requires that the disk and slices to be backed up not be in use. The system disk contains file systems (such as the root (/) file system) that cannot be unmounted. In backing up the system disk, special procedures are required. The following are s

• Fujitsu Solaris 10, Figure 4.1 Example of VLAN environment By using VLAN, traffic management of two or more networks by the single physical interface can be done. In order to create Figure 4.1 Example of VLAN environment, it is needed a VLAN setup (VLAN ID and Tagged/Untagged) of a switch. The vlan numbers fjgi interface can offer: - No TagVLAN - With TagVLAN PRIMEPOWER PRIMEPOWER To X.X.1.X To X.X.2.X To

• Fujitsu Solaris 10, 23 ok cd /pci@83,2000/FJSV,pwga@1 <Return> ok .prp <Return> role slave *1 duplex half *2 transfer-speed 0000000a *3 cabinet-name Cabinet#0 board-name Motherboard#1 assigned-addresses 83002810 00000000 00100000 00000000 00010000 82002830 00000000 00110000 00000000 00010000 *1: Appears only when slave-mode is set. *2: Appears only when half-duplex is set. *3: Appears only when transfer-speed is set. [10Mbps:0xa, 100Mbps:0x64] In the

Related Products and Documents (Software):

Comparable Devices:

Similar Resources:

• Yamaha mLAN mLAN Driver (16 pages) 1 Table of Contents mLAN Control Panel’s Manual ...................2 What is mLAN Control Panel? ........................................... 2Starting mLAN Control Panel............................................ 2mLAN Control Panel menu................................................ 3mLAN Control Panel window............................................ …

• Dell PowerVault MD3620i (292 pages) Dell PowerVault MD3600i andMD3620i Storage ArraysOwner’s ManualRegulatory Model: E03J Series and E04J SeriesRegulatory Type: E03J001 and E04J001book.book Page 1 Tuesday, September 27, 2011 3:13 PM …

• HP dc7700 Convertible Minitower P (29 pages) 12/16/2018 HP Compaq dc7700 Business PC - Removal and Replacement Procedures -- Small Form Factor (SFF) Chassis | HP® Customer Supporthttps://support.hp.com/us-en/product/hp-compaq-dc7700-small-form-factor-pc/3232029/document/c00862331#AbT11 1/29PRODUCT HOMEHP Compaq dc7700 Business PC - Removal and Replacement Procedures-- Small Form Factor (SFF) Chassis� …

• Lexmark T656 (119 pages) Card for IPDS and SCS/TNe IPDS Emulation User’s Guide Printers Multifunction Products • Lexmark C734, C736 • Lexmark E460dn, E460dw • Lexmark E462dtn • Lexmark T650, T652 • Lexmark T654 • Lexmark T656dne • Lexmark W850 • Lexmark X463de, X464de • Lexmark X466dte, X466dtwe • Lexmark X651de, X652de • Lexmark X …

• LevelOne CamCon FCS-1070 (3 pages) Day/Night Network CameraFCS-1070H/W Version: 1Product Overview The LevelOne Day/Night IP Network Camera is a powerful surveillance camera that connects easily with a wired Ethernet to provide high-quality video and audio to a control room or broadcast it to remote locations over the Internet. The FCS-1070 dual-Codec network camera with 2-way audio and ex …

• Lexmark MS610de (4 pages) Printing GuideLoading traysCAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability, load each tray separately. Keep all other traysclosed until needed.1 Pull the tray completely out.Note: Do not remove trays while a job prints or while Busy appears on the printer display. Doing so may cause a jam.2 Squeeze, and then slide the width guide tab …

Comments, Questions and Opinions: