Manualios.com

Fujitsu XG700 - Switch Operation & User’s Manual

Fujitsu XG700 - Switch Manual Online:

4.35, 955 votes
Fujitsu XG700 - Switch User Manual
Fujitsu XG700 - Switch User Guide
Fujitsu XG700 - Switch Online Manual

Text of Fujitsu XG700 - Switch User Guide:

  • Fujitsu XG700 - Switch, XG700 User's Guide 163/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 % Can't set mrouter on a port which belongs to an aggregation port. Explanation A port which configures a link aggregation cannot be specified for port. Solution Review the specified port number and reissue the command. When setting for the aggregation group specify agg-port. Example Set aggregation group 1 as a multicast router port: xg(config)# ip snooping vlan 2 mrouter agg-port 1 5.14.6 ip snooping vlan group-member-interval Function Sets an vali

  • Fujitsu XG700 - Switch, XG700 User's Guide 224/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 6.3 Updating Firmware The XG700 can hold two versions of firmware. If you perform a firmware update, the inactive firmware will be updated. The XG700 automatically uses the new firmware (updated version) during reboot after the firmware update. If it fails to start the new firmware for some reason, it automatically uses the old version (the one that has not been updated). If you have problems with the new version, you can manually select the old version. First, we describes the procedures for updating firmware.  Preparing the TFTP Ser

  • XG700 User's Guide 121/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.9.10 port-security Function Sets port security by the source MAC address. When port security is enabled, register the MAC address to permit using the "bridge mac-address-table" command. Use the no form to disable port security. Prompt xg(config-if)#,

  • XG700 User's Guide 222/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 6.1.3.3 Verifying XG700 Status Change To verify changes in the XG700 status, review INFO log messages. Enter the "show log " command in the operator EXEC mode or in the administrator EXEC mode. For the meaning of messages, refer to "List of

  • Fujitsu XG700 - Switch, XG700 User's Guide 48/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 4.9.1 Registering Group Members Upon reception of an IGMP Report message, the XG700 registers a multicast MAC address with the MAC address table for the port that received the IGMP Report message and the port to which a multicast router is connected. The following figure shows the relationship between the registered IP multicast address and the multicast MAC address. MAC addresses that are registered with IGMP snooping a

  • Fujitsu XG700 - Switch, XG700 User's Guide 245/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 Message IDSeverity Message/Explanation/Solution S4503 WARNING Received BPDU on PortFast enable port. shutting down %1$. Explanation A BPDU was received on a Port Fast-enabled port.  [[Inserted string]]%1$: Name of the port that received the BPDU Solution Review the connection port. P4504 WARNING Invalid "Forward delay time" relationship 2*(%1$ - 1) >= %2$. Explanation The setting of STP Forward Delay is invalid. �

  • Fujitsu XG700 - Switch, XG700 User's Guide 75/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 % OFFSET '%1$' is invalid Explanation The specification of OFFSET is incorrect. [[Inserted string]]%2$: incorrect parameter value is displayed. Solution Correct the error of the parameter, and execute it again. % Parameter '%1$' is too long Explanation Specification of the parameter is too long. [[Inserted string]]%1$: incorrect parameter value is displayed. Solution Correct the error of the parameter, and exe

  • Fujitsu XG700 - Switch, XG700 User's Guide 28/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 4.1.5 Storm Control The XG700 discards broadcast frames when the number of received broadcast frames is over a given threshold to prevent unnecessary waste of bandwidth due to retained broad cast frames on the network. This function is called "Storm Control". For each port, it is possible to configure storm control. When broadcast frames are discarded by Storm Control, error logs are output, after which storm control logging is disabled. To re-enabled logging, violations must be cleared with "clear violation". To configure Storm Control, carry out the following

  • Fujitsu XG700 - Switch, XG700 User's Guide 251/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 A.3 Message Format for Forwarding syslog The logs output from the XG700 can be forwarded to your syslog server. The XG700 forwards logs in a message format that conforms to the RFC3164 The BSD Syslog Protocol. The format the XG700 uses to forward a syslog message to the syslog server is shown below. Format of syslog message in XG700 Description Format of syslog message in RFC3164 Priority Priority string PRI part Priority Time Time at which the message is generated (MM:DD:HH:MM:SS)

  • Fujitsu XG700 - Switch, XG700 User's Guide 130/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 Output form (in detailed display) xg# show spanning-tree detail Spanning Tree Information 2005/08/22-12:12:15 =============================================================================== Switch Information for Spanning Tree --------------------------------------------------------------- Spanning Tree : {Enable | Disable} Root Switch Priority: 32768 Root Switch ID : 8000.0080.17C2.0511 Root Path Cost : 6 Root Port : port-1 Switch Priority : 32769 Switch ID :

  • XG700 User's Guide 199/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006  Rising Threshold Indicates the threshold upper limit (or the rising threshold).  Rising Event Indicates a number of the event to be notified if the value obtained has exceeded the threshold limit.  Falling Threshold Indicates the threshold lower limit (or the fall

  • XG700 User's Guide 206/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.18.2 show system information Function Displays the operation status of the XG700. Prompt xg> or xg# Command syntax show system information Command type Operation management command Output format xg# show system information System Information 2005/08/22-21:06:11 =======

  • Fujitsu XG700 - Switch, XG700 User's Guide 215/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 % Checksum error: %1$ in FlashROM Explanation An error has occurred during writing of flash ROM data. [[Inserted string]]%1$: Firmware configuration module Solution Retry firmware updating. If the error recurs, contact to the maintenance support personnel. % %1$ in SRAM is invalid. Explanation Inconsistency of non-volatile (SRAM) memory data was found due to amended firmware updating or others. [[Inserted string]]%1$: Abnormal memory contents Solution Restart the system using the “reset” command. Then, retry firmware updating. If the error recurs, contact to the maintenance

  • Fujitsu XG700 - Switch, XG700 User's Guide 195/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.16.3 snmp-server contact Function Sets the installation location of the XG700. Use the no form to return to the default setup. Prompt xg(config)# Command syntax snmp-server contact SYSTEM-CONTACT no snmp-server contact Parameter  SYSTEM-CONTACT Specifies the installation location of the XG700. The location name can be up to 255 alphanumeric characters. Command type Configuration command Default None Message % SYSTEM-LOCATION is too long. Explanation The location name specified by "SYSTEM-LOCATION" has exceeded the limit length.

  • XG700 User's Guide 47/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 4.9 IGMP Snooping IP multicast is often used to distribute multimedia data, including video and voice, over a network. A general layer 2 switch floods multicast frames, causing absorption of unnecessary network bandwidth. A layer 3 switch that supports Internet Group Management Protocol (IGMP

  • Fujitsu XG700 - Switch, XG700 User's Guide 228/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 Chapter 7 Troubleshooting This chapter describes how to solve problems you encounter when using the XG700.

  • Fujitsu XG700 - Switch, XG700 User's Guide 204/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.18 System Operation Display Commands This section explains about the command to display the system operation status. 5.18.1 show system status Function Displays the hardware operation status. For the explanation and actions taken of each item, see the "Verifying Hardware Status ". Prompt xg> or xg# Command syntax show system status Command type Operation management command Output format xg11# show system status System Status Informat

  • Fujitsu XG700 - Switch, XG700 User's Guide 211/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.19.4 save maintenance Function Stores the current system status data as the maintenance information in the non-volatile memory. Prompt xg# Command syntax save maintenance Command type Operation management command 5.19.5 show maintenance Function Displays the maintenance information. Prompt xg# Command syntax show maintenance Command type Operation management command Output format (if "current" is specified) xg# show maintenance Maintenance Information 2005/08/22-20:58:17 ======================

  • Fujitsu XG700 - Switch, XG700 User's Guide 249/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 Message IDSeverity Message/Explanation/Solution S7627 ERROR firm-update: failed (verification error: rootfs). Explanation An error has occurred while updating firmware. Solution Reattempt the update process. If the message is displayed repeatedly, note the message contents and contact your XG700 sales representative. S7628 ERROR firm-update: failed (writing to FlashROM error: EL). Explanation An error has occurred while updating firmware.

  • Fujitsu XG700 - Switch, XG700 User's Guide 210/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 Example Display 10 entries of the latest INFO log: xg# show log info latest 10 5.19.3 log send Function Transfers the system log from the system equipment to the remote host. Prompt xg(config)# Command syntax log send HOST { info | warning | error | critical } [ { udp | tcp } ] no log send Parameter  HOST Specifies the host name, domain name or IP address of the destination of system logs. When specifying the host name or the domain name, you must set the DNS server or register the host nam

  • Fujitsu XG700 - Switch, XG700 User's Guide 148/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.11.5 user-vlan-protocol-id Function The VLAN tag protocol ID (VPID or TPID) used for VLAN tag identification can be changed to the user-defined value of each port. The standard VLAN tag protocol ID has been defined to 0x8100 in IEEE 802.1Q. However, you can use the standard tag of IEEE 802.1Q as the multiple-tag VLAN which has been encapsulated with the user-defined VPID (or TPID) tag (*). *: Similar functions are called as Stacked VLAN, Nested VLAN, VLAN tunneling and 802.1Q in 802.1Q.  For the frame format, see the TPID (Tag Protocol Identi

  • Fujitsu XG700 - Switch, XG700 User's Guide 94/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 Example Display the content of all MAC address tables. xg# show bridge mac-address-table Mac Address Table Information 2005/08/22-12:12:15 =================================================================== Static Mac-address Table ------------------------------------------------------------------- Mac-address Vlan-id Destination-port -------------- -------- -------------------- 0001.123a.4321 vlan-1 port 2 0002.123a.4321 vlan-1 port 4 0003.123a.4321 vlan-3 filter ef01.123a.4321 vlan-3

  • Fujitsu XG700 - Switch, XG700 User's Guide 25/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 Chapter 4 Functions and Procedures for Setting Functions This chapter describes the functions of the XG700 and how to set the functions. Refer to "Operating Environment for CLI " for details on using CLI. Refer to "Command Reference" for details on commands.

  • Fujitsu XG700 - Switch, XG700 User's Guide 16/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 2.2 Using the CLI 2.2.1 How to Enter Commands  Command Entry Format Separate each command, subcommand and argument with a single space. <command> <subcommand> <argument 1> <argument 2> ... (" " indicates a space.) xg(config)# management-interface ip 192.168.1.10/24 default-gw 192.168.1.150 xg(config)# management-interface dns-server 192.168.1.150  Characters that ca

  • Fujitsu XG700 - Switch, XG700 User's Guide 56/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.1 About Command Reference This section describes how to read command references. 5.1.1 Command System The following is the system of commands provided in the XG700: Item Function Management LAN Interface Configuration commands They are used to set items related to management LAN interface. Serial/telnet configuration commands They are used to set items related to serial and telnet connections. System Basic Operation commands They are necessary for system operation such as system time setting and password setting, and file operation. Configurat

  • Fujitsu XG700 - Switch, XG700 User's Guide 136/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.10.7 spanning-tree forward-time Function The forward delay time of Spanning Tree is the time required in each state when the ports transit to forwarding state. The no form of is used to return to the default setup. Prompt xg(config)# Command syntax spanning-tree forward-time <4-30> no spanning-tree forward-time Parameter  forward-time <4-30> Sets the forward delay time of Spanning Tree in units of seconds. Values can be set in the range of 4 to 30 seconds. Command type Configuration command Def

  • XG700 User's Guide 76/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.4.15 ping Function Checks if communication with the specified host is possible by sending ICMP Echo Request packet to the specified host from the manage LAN interface of the XG700 and receiving ICMP Echo Reply packet. Prompt xg>, or xg# Command syntax ping HOST [ count <1-100> ] Pa

  • Fujitsu XG700 - Switch, XG700 User's Guide 201/266 A ll Rights Reserved, Copyright (C) PFU LIMITED 2005-2006 5.17.3 rmon alarm Function Sets RMON alarms. Up to 30 entries can be set. Use the no form to delete the information you have set. Prompt xg(config)# Command syntax rmon alarm INDEX VARIABLE interval VALUE {absolute | delta} rising-threshold VALUE [EVENT-NUM] falling-threshold VALUE [EVENT-NUM] [owner OWNERNAME] no rmon alarm INDEX Parameter  INDEX Specifies an entry index of the RMON alarm within the range of 1 to 65535.  VARIABLE

More Instructions:

DOWNLOAD

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 PYLE Audio PHPW2 Operation & user’s manual pyle-audio/phpw2-JP4.pdf 29 Dec 2022 1
2 GeoSafari Talking Globe Instruction manual geosafari/talking-globe-533.pdf 21 Jul 2023 11
3 Sanyo MDF-5386SC Specifications sanyo/mdf-5386sc-NV5.pdf 09 Apr 2023 2 0.52 Mb
4 Echo HC-150 Operator's manual echo/hc-150-55H.pdf 22 May 2023 64 2.28 Mb
5 Ray display Pico Projector Operation & user’s manual ray-display/pico-projector-X34.pdf 01 Dec 2023 18
6 Craftsman 151.30382 Operating manual craftsman/15130382-ZT5.pdf 25 May 2023 27

Similar Resources:

  • Pentagram

    NEsT 16P Compact

    (28 pages)
    2007-05-16 INDEX INTRODUCTION..................................................................................................... EN - 2 DEVICE EXTERNAL LOOK................................................................................... EN - 3 DEVICE OPERATION ............................................................................................ …
  • EAST COAST

    A/B Switch

    (3 pages)
    A/B Switch, Installation Guide Manual PT# 262008 Rev- EAST COAST DATACOM, INC., 245 Gus Hipp Blvd., STE 3, Rockledge FL 32955 TEL: (321) 637-9922 FAX: (321) 637-9980 www.ecdata.com DESCRIPTION The A/B Switch allows secure and safe switching between computer or data ports. The unit supports switching 4-wires of user data traffic from th …
  • Cross Technologies

    1582-10M

    (14 pages)
    Instruction Manual Model 1582-10M Protection Switch January 2009 Rev O MENUEXECUTEMODEL 1582SWITCHCROSS TECHNOLOGIES INC.REMOTECH11POWER2CH2ALARMSOUTPUT = CH1AUTOData, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be reproduced or duplicated without the prior permission of …
  • Parker

    116942-01 Series

    (2 pages)
    1Bulletin HY11-5715-703Parker Hannifin CorporationHydraulics GroupHY11-5715-703 Stellungsschalter 116942-43.indd CM 10.09.15InstallationInstallationshinweiseTechnische DatenAnschlussplanAnschlussplanEndschalterEndschalterPositionskontrollschalterSerie 116942-01, 116943-01Die werkseitige Einstellung des Positions-Kontrollschal-ters darf nicht verändert werd …
  • H3C

    S5830V2 series

    (22 pages)
    H3C S5830V2 & S5820V2 Switch SeriesMCE Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release2108 Document version: 6W101-20120531 …
  • Planet

    FNSW-4800

    (18 pages)
    TrademarksCopyright  PLANET Technology Corp. 2005.Contents subject to revision without prior notice.PLANET is a registered trademark of PLANET Technology Corp. All other trade-marks belong to their respective owners.DisclaimerPLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warran …

Comments, Questions and Opinions: