Furuno GP-80 Installation Manual

Text of Furuno GP-80 User Guide:

• Furuno GP-80, 5. INITIAL SETTINGS 13 DATA 1 output setting 1) Press [MENU] [9] and [3]. The DATA 1, 3 OUTPUT SETUP menu appears. Talker ID GP LC DE Output Data (00-90 sec)84% 1. AAM:00 APA:00 APB:01 BOD:00 2. BWC:00 BWW:00 GGA:01 GLL:00 3. RMB:01 RMC:01 VTG:01 WCV:00 4. WINC:00 WPL:00 XTE:00 ZDA:01 5. GNS:00 ZTG:000 Rnn:00 RTE:00 DATA3. Log Pulse 400ppm DATA 1, 3 OUTPUT SETUP MENU : Escape ENT : Enter 200ppm Settings shown here are default settings. This line appears only when LOG is selected by internal jumper wires. Data Fmt. V1.5 IECV2.0 Figure 5-1 DATA 1, 3 OUTPUT SETUP menu 2) Press ! or " to select Data Fmt. 3) Press # or $ to selec

• Furuno GP-80, 6. OPTIONAL DGPS 22 7) Press ! or " to select First Bit. 8) Press # or $ to select first bit; MSB or LSB. 9) Press " to select Parity. 10) Press # or $ to select parity bit; EVEN, ODD or NONE. 11) Press " to select Stop Bit. 12) Press # or $ to select stop bit; 1 or 2. 13) Press " to select Band Rate. 14) Press # or $ to select band rate; 4800 or 9600. 15) Press the [MENU ESC] key.

• Furuno GP-80, 5. INITIAL SETTINGS 12 AGFPA: Autopilot information from FURUNO autopilot equipments Port Input Output DATA1 DATA2 NMEA 0183 Ver. 1.5 /2.0 AGFPA , DBT, DPT, MTW, TLL IEC 61162-1/NMEA 0183 Ver.1.5/ Ver.2.0 AAM, APA, APB, BOD, BWC, BWR, BWW, GGA, GLL, GNS, RMB, RMC, VTG, WCV, WNC, WNR, WPL, XTE, ZDA, ZLZ, ZTG, Rnn, RTE, DTM LOG PULSE DATA3 External MOB Same as the data output form “DATA1” General data DATA4 DGPS or general data (Selected by menu) IEC 61162-1/NMEA 0183 Ver.1.5/ Ver.2.0 AAM, APA, APB, BOD, BWC, B

• 5. INITIAL SETTINGS 15 Setting DATA 4 to Data Output 1) Press [MENU] [9] and [5]. The DATA 4 I/O SETUP menu appears. DATA 4 I/O SETUP 1/2 To Next Page ENT : Enter MENU : Escape Appears only when external DGPS receiver is used. DATA 4. Level RS232C RS422 Data Out Com. DGPS : Select Figure 5-3 DATA 4 I/O SETUP menu 2) Press ! or " to select Level

• Furuno GP-80, 5. INITIAL SETTINGS 9 83 21 Error rate of connection data Beacon signal status Reference station status DGPS signal strength This value is between 1 and 84. The higher the value, the stronger the signal. If a noise appears at reception band width, the value becomes bigger. This value is between 1 to 22. The higher the value, the better the reception of beacon signal. When this value is less than 20, the error is included in the correction data. In this time, position fixing is done by using past position data. When the ship is in the service area of a beacon station, this v

• 7 5. INITIAL SETTINGS Checking Operation 1. Turn on the GP-80. 2. Confirm that "OK" and "BEACON RCVR INSTALLED" are display on the self-test display. Confirm that "BEACON RCVR INSTALLED" is displayed when DGPS function is provided. BEACON RCVR INSTALLED DATA #3: LOG PULSE OUTPUT PROGRAM MEMORY =OK SRAM =OK =OK Internal Bat

• Furuno GP-80, INSTALLATION MANUAL GPS NAVIGATOR GP-80 1. EQUIPMENT LIST ............................................................................................ 1 2. DISPLAY UNIT .................................................................................................. 2 3. ANTENNA UNIT................................................................................................ 3 4. WIRING ............................................................................................................. 5 5. INITIAL SETTINGS .........................................

• Furuno GP-80, 5. INITIAL SETTINGS 8 5. Press the [NU/CU ENT] key. 6. Press the [MENU ESC] key. Manual DGPS setup Enter four digit ID number, frequency and baud rate of station, referring to the DGPS list in the GP-80 operator's manual. 1. Press [MENU ESC] [9] and [7] to display the DGPS SETUP menu. 2. Press ! or " to select DGPS MODE and press # to select On. 3. Press ! or " to select Ref. Station. 4. Press $ to select Man. 5. Enter four digit ID number. You can clear an entry by the [CLEAR] key. If the number entered is invalid, the buzzer sounds and the message "INVALID

• Furuno GP-80, 3 3. ANTENNA UNIT Mounting Install the antenna unit referring to the installation diagram on page D-4. When selecting a mounting location for the antenna unit, keep in mind the following points. • Select a location out of the radar beam. The radar beam will obstruct or prevent reception of the GPS satellite signal. • Be sure the location offers a clean line-of-sight to satellite. Objects within line-of-sight to a satellite, for example, a mast or funnel, block reception and cause prolonged acquiring time or interruption of position fix. • Mount the

• 5. INITIAL SETTINGS 16 Setting DATA 4 to “COM.” (general data) Waypoints and Routes data can be received from a personal computer, through the DATA 4 port. 1) Press [MENU] [9] and [5]. 2) Press ! or " to select Level. 3) Press # or $ to select level of personal computer; RS232C or RS422. 4) Press the [ENT] key. 5) Press $ to select Com

• Furuno GP-80, SAFETY INSTRUCTIONS WARNING Do not work inside the equipment unless totally familiar with electrical circuits. Hazardous voltage which can cause electrical shock, burn or serious injury exists inside the equipment. Turn off the power at the mains switchboard before beginning the installation. Post a sign near the switch to indicate it should not be turned on while the equip- ment is being installed. Fire, electrical shock or serious injury can result if the power is left on or is applied while the equipment is being installed. Ground the equipment to prevent electrical shock and mutual interference. Confirm that the

• Furuno GP-80, ＰＡＣＫＩＮＧ　ＬＩＳＴ ＰＡＣＫＩＮＧ　ＬＩＳＴＰＡＣＫＩＮＧ　ＬＩＳＴ ＰＡＣＫＩＮＧ　ＬＩＳＴ 20AM-X-9851 -10 GP-80-**-0/0-HK GP-80-**-0/0-HKGP-80-**-0/0-HK GP-80-**-0/0-HK N A M E O U T L I N E DESCRIPTION/CODE № Q'TY 1/1 ユニット ユニットユニット ユニット UNIT UNITUNIT UNIT 空中線部 ANTENNA UNIT GPA-017S 000-040-537 1 (*1) ** 空中線部 ANTENNA UNIT GPA-018S 000-041-462 1 (*1) 空中線部 ANTENNA UNIT GPA-019S 000-142-545 1 (*1) 受信演算部 DISPLAY UNIT GPR-020-E-N 000-040-542 1 ** 予備品 予備品予備品 予備品 SPARE PARTS SPARE PARTSSPARE PARTS SPARE PARTS SP20-00500 SP20-00500SP20-00500

• Furuno GP-80, 21 6. OPTIONAL DGPS Beacon Receiver Set GR-80 GP-80 GR-80 DATA DATA4 NP Board JP3 Open TD-A TD-B RD-A RD-B GND RD-A RD-B TD-A TD-B GND 1 2 3 4 5 6 7 4 3 2 1 7 RS-422* RS-422 * This connection is required for L/L Auto mode of GR-80. Whip Antenna Preamp unit (with 15 m cable) WHT BLK YEL GRN BLU P P When the GP-80 is connected with Beacon Receiver GR-80, do the setting as follows. Signal level RS-422 *1 First Bit LSB Parity Bit NONE Stop Bit 1 Communication Speed 4800 or 9600 *1 *1: Coincide with the setting of the Beac

• CODE NO. CODE NO.CODE NO. CODE NO. TYPE TYPETYPE TYPE 略  図 OUTLINE 名  称 NAME 数量 Q'TY 用途／備考 REMARKS 番 号 NO. 型名／規格 DESCRIPTIONS 1/1 -1 INSTALLATION MATERIALS 工事材料表 工事材料表工事材料表 工事材料表 GP-80,GP-90,SC-55,GP-3500/F       GP-1850,GP-1650,FA-100,GP-1640/F     SC-60/120,G

• Furuno GP-80, 3. ANTENNA UNIT 4 How to attach the N-P-8DFB connector Outer Sheath Armor Inner Sheath Shield Remove outer sheath and armor by the dimensions shown left. Expose inner sheath and shield by the dimensions shown left. Cut off insulator and core by 10mm. Twist shield end. Clip on clamp nut, gasket and clamp as shown left. Fold back shield over clamp and trim. Cut aluminum foil at four places, 90° from one another. Fold back aluminum foil onto shield and trim. Expose the insulator by 1mm. Expose the core by 5mm. Slip the pin onto the conductor. Solder them together through the hole on t

• Furuno GP-80, 1 A 34 B C 2 Ｆ ＦＦ ＦＵ ＵＵ ＵＲ ＲＲ ＲＵ ＵＵ ＵＮ ＮＮ ＮＯ ＯＯ ＯＥ ＥＥ ＥＬ ＬＬ ＬＥ ＥＥ ＥＣ ＣＣ ＣＴ ＴＴ ＴＲ ＲＲ ＲＩ ＩＩ ＩＣ ＣＣ ＣＣ ＣＣ ＣＯ ＯＯ Ｏ． ．． ．， ，， ，Ｌ ＬＬ ＬＴ ＴＴ ＴＤ ＤＤ Ｄ． ．． ． TNC-P-3 TNC-PS-3D-15, 15m, φ5.3 NJ-TP-3DXV-1 1m, φ5.3 GND (+) (-) 1 2 MJ-A2SPFD 1 2 GPS J12 ANT J1 アカ RED クロ BLK FUSE 2A 整流器 RECTIFIER PR-62 *1 DPYC-1.5 1φ,50/60Hz 100/

• Furuno GP-80, 5 4. WIRING The figure below shows the connection of cables on rear of display unit. Ground the receiver to prevent loss of sensitivity and mutual interference. CAUTION Rear of Display Unit Ground External Equipment FUSE 2A Black Red DATA 1 DATA 3 DATA 4 DATA 2 INPUT 10.2~31.2VDC Antenna Unit GPA-018S GPA-017S 20cm GPA-019S ANT + – Connection of cables on display unit

• Furuno GP-80, 5. INITIAL SETTINGS 19 "DATA2" Port ! IEC 61162-1/NMEA 0183 Ver. 1.5/Ver. 2.0 Output • Output Schematic Diagram (Talker) 1 J7 2 3 4 5 6 DATA2 TD-A TD-B FL10 20P8147 MJ-A6SRMD FL9 16 17 18 U35 SN75ALS172 • Output Drive Capability Max. 10mA • IEC 61162-1 output is subject to the standard IEC 61162-1 First edition 1995-11. • Output Sentence is described on page 8 and 9. Each sentence is output at the interval entered. ! NMEA 0183 Input • Input Schematic Diagram (L

• Furuno GP-80, 5. INITIAL SETTINGS 18 Interface Documentation "DATA1" Port ! IEC 61162-1/NMEA 0183 Ver. 1.5 Output • Output Schematic Diagram (Talker) 1 2 6 6 7 8 DATA 1 J5 TD-A TD-B FL14 FL13 MJ-A6SRMD 20P8147 U35 SN75ALS172 • Output Drive Capability Max. 10mA • IEC 61162-1 output subject to the standard of IEC 61162-1 First edition 1995-11. • Output Sentence is described on page 8 and 9. Each sentence is output at the interval entered. ! NMEA 0183 Input • Input Schematic Diagram (Listener) 1 J5 2 3 4 5 6 RD-H RD-

• Furuno GP-80, 5. INITIAL SETTINGS 14 DATA 2 output setting 1) Press [MENU] [9] and [4]. The DATA 2 OUTPUT SETUP menu appears. 183/V2.0 Talker ID GP LC DE Output Data (00-90 sec)80% DATA2 OUTPUT SETUP MENU : Escape ENT : Enter NMEA Fmt. 183/V1.5 : Select Setting shown here are default settings. 1. AAM:00 APA:00 APB:04 BOD:00 2. BWC:00 BWR:00 BWW:00 GGA:00 3. GLL:01 RMB:01 RMC:01 VTG:01 4. WCV:00 WNC:00 WNR:00 WPL:10 5. XTE:00 ZDA:01 GNS:00 ZTG:00 Figure 5-2 DATA 2 OUTPUT SETUP menu 2) Follow the procedure for setting DATA 1 output. DATA 3 output setting The DATA 3 can output NMEA 0183 (V1.5/V2.0) /IEC 61162-1 data or log pulse by selecting inner jumper wire. For NMEA

More Instructions:

	Furuno GP-80 Installation manual 14-09-2022 12	DOWNLOAD
	Furuno GP-80 Operator's manual 10-04-2024 2	DOWNLOAD
	Furuno GP-80 Operator's manual 26-11-2023 119	DOWNLOAD
	Furuno GP-80 Operator's manual 27-09-2023 103	DOWNLOAD

Related Products and Documents (GPS):

Comparable Devices:

Similar Resources:

• EverMore GT-800 (9 pages) GT-800 User’s Manual EverMore Technology, Inc. 2F, No.7, R&D Road 1, Science-Based Industrial Park, Hsinchu, Taiwan, 300, R.O.C. http://www.emt.com.tw Page 1 GT-800 GeoTagger User’ s Manual Date: August, 2007 Version: 2.2 All Rights Reserved …

• Sanav GS-818 (79 pages) SANAV GS-818 GPS/GSM/GPRS Vehicle Tracker User Manual Revision: 1.6.0 Revision Date: 2011/12/10 December 2011 1.6.0 Copyright © 2011 San Jose Technology, Inc. All Rights Reserved. This document contains information that is the property of SANAV. This document may not be copied, reproduced, re …

• The GPS Stick USB GPS Receiver (5 pages) USB® GPS Receiver 54 channels Built-in AGPS Function User’s Manual www.TheGPSStick.com GPS Stickit’n GO! 1 …

• Blaupunkt TRAVELPILOT FREESTYLER (104 pages) Navigation Radio CDwww.blaupunkt.comThe GPS antenna must be positionedoptimally to enable precise navigationwithout a speed signal.Please observe particularly theinstallation note in point 3.2 on page 97and the installation test on page 90.Operating and installation instructions 0 Umschlag EX_gb 12.04.2005, 14:12 Uhr1 …

• RUPTELA FM-Tco4 HCV (4 pages) www.ruptela.com [email protected] | +370 5 2045030 1 FM-Tco4/FM-Pro4 Quick Start Guide Q FM-Tco4 HCV FM-Tco4 LCV FM-Pro4 Make sure that you have: • A computer with Windows 7/8/10 • An internet connection (or a predownloaded Device Center) • A USB A to USB mini (Type B) cable • Tools for installation and wire connection: a screwdriver, a pa …

• Pioneer AVIC-F90BT (57 pages) INSTALLATION MANUALMANUEL D’INSTALLATIONFLASH MEMORY MULTIMEDIA AV NAVIGATIONRECEIVERRECEPTEU R AV MULTIMEDIA A MEMOIRE FLASHAVEC SYSTE ME DE NAVIGATIONAVIC-F90BTEnglish Français …

Comments, Questions and Opinions: