Rattler 369D Owner's Manual
|
18 © 2003 directed electronics, inc. The after-market safety switch will have two wires coming off it. Take one of the wires (it does not matter which one) and strip back a ¾-inch section of the insulation off the wire. Crimp a ring terminal to the wire, and using a self tapping screw, drill the screw with the ring terminal to the same area as the ground wire. Solder the ot
Rattler 369D, 19 © 2003 directed electronics, inc. BLACK/WHITE wire on the secondary connector and cover the connection with electrical tape. The shut down toggle switch is designed to shut the remote start off in an emergency or to disable the remote start functions temporarily (i.e., for service on the vehicle). If your vehicle came with a factory neutral safety switch this switch needs to be installed in line with the black/ white wire, instead of soldering the black/ white wire to the factory neutral safety wire solder the black/ white wire to one side of the switch ( it does not matter which side) and solder the other side to the vehicle factory neutral safety switch. step 5 Parking ligh
Rattler 369D, 29 © 2003 directed electronics, inc. step 11 Testing the system Once steps 1-9 have been completed, the operation of the system can be tested. Place the two 30-amp fuses back into the relay satellite red wire fuse holders. Make sure that the vehicle is in park with the emer- gency brake on and the hood closed. Press twice on the remote control to initiate the remote start function. The parking lights should flash to confirm the remote start command has been received, The accessories and ignition should turn on followed by the starter cranking and the vehicle engine running. Pressing twice again will shut the engine off. ➜
Rattler 369D, 20 © 2003 directed electronics, inc. Using the web information on the vehicle, locate the suspected wire and place the red lead of the meter to a constant (+)12 volt source and secure it. Place the multi-meter in the DC position. Using the black lead of the meter, probe the wire. With the switch in the off position the meter will read 0.00 volts. While watching the meter, turn the switch to the parking light posi- tion. The meter will read between 10.00 volts and 13.00 volts. Once you have identif
Rattler 369D, 3 © 2003 directed electronics, inc. wwhhaatt iiss iinncclluuddeedd ➤ Control Module ➤ One 3-Button Transmitter ➤ 9-Pin Main H/1 Harness ➤ 5-Pin H/2 Secondary Harness ➤ 4-Pin External Relay ➤ HF+ External Receiver and Cable ➤ Shutdown Toggle Switch ➤ Dual-Relay Door Lock Module ➤ Plug-in Valet/Program Button iinnssttaallllaattiioonn ttoooollss ➤ Digital Multi-Meter ➤ Drill ➤ 9 /32 and 5 /16 Drill Bits ➤ Screwdrivers (Phillips and Flathead) ➤ Wire Stripper ➤ Solder Iron ➤ Electrical Tape ➤ Plier
Rattler 369D, 26 © 2003 directed electronics, inc. step 8 Factory Alarm Arm or Disarm Since most newer vehicles come equipped with a factory alarm system, it is necessary for the factory alarm to be armed/disarmed when unlocking the doors and disarmed while remote starting the vehicle. Locate the factory alarm arm/disarm wires using the web site vehicle information. Once the suspect wires are located, place the multi-meter’s red lead to a (+)12 volt constant source and secure it. Put the multi-meter in the DC position then probe the suspect wire wit
Rattler 369D, 34 © 2003 directed electronics, inc. go out indicating the change. 4. RReelleeaassee . The Program switch can now be released. You can advance from feature to feature by pressing and releasing the Valet/Program switch the number of times neces- sary to get from the feature you just programmed to the feature you wish to access. For example, if you just programmed the run time (Feature 3) and you next want to program parking lights (Feature 4) to constant, release the Valet/Program switch. Press and release it once to advance from Fe
Rattler 369D, 52 © 2003 directed electronics, inc. Was the Tach Learn successful? The LED must light solidly and brightly to indicate a successful learn. Make sure that there is a tach signal right at the purple/white tach input wire of the remote start. If not, recheck the connection to the vehicle’s tach wire and make sure the wire is not broken or shorted to ground leading to the remote start. ➤ The vehicle will start and run only for about 10 seconds. Is the remote start programmed for voltage sense? Try programming the unit for low voltage reference. If this does not work a tach wire should be used.
55 © 2003 directed electronics, inc. nnootteess _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _____________________________________________
Rattler 369D, 40 © 2003 directed electronics, inc. 5. Press and release the Program switch. The LED will now report the last system shutdown by flashing for one minute in the following grouped patterns: The factory settings are indicated in bold text in the table below. ttrraannssmmiitttteerr ffuunnccttiioonnss The receiver uses a computer-based learn routine to learn the transmitter buttons. This makes it possible to assign any specific transmitter button, or combination of buttons, to any receiver function. The transmitter initially comes programmed with the Standard Config
Rattler 369D, 51 © 2003 directed electronics, inc. after the remote start becomes active. If there is voltage present, skip to Step 4. If there is not voltage present, advance to Step 2. Check the 30A fuses. Make sure the purple starter wire is connected on the starter side of the optional starter kill relay. Does the vehicle have an immobilizer? Some immobilizer systems will not allow the vehicle to crank if active. Check connections. The two red heavy gauge input wires on the relay satellite should have solid connections. "T-taps", or "scotch locks" are not rec
43 © 2003 directed electronics, inc. keys in the ignition. The user must also have the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed Electronics, Inc. dealer in accordance with the Safety Check outlined in the product installation guide.
Rattler 369D, 27 © 2003 directed electronics, inc. When the correct wire has been found, solder the small GREEN/BLACK wire to the wire which activates in the unlock position when the key is turned. Connect the GREEN/WHITE wire to the wire which activates in the lock position when the key is turned. After these wires have been connected cover the connection with electrical tape. step 9 Immobilizer Bypass Modules Most newer vehicles have a factory engine immobilizer system designed to prevent any unauthorized use of the vehicle. These immobilizers will cut off power to the starter and the fuel supply preventing
Rattler 369D, 46 © 2003 directed electronics, inc. While the vehicle is running during remote start operation, the system will monitor the vehicle and will automatically shut down the engine if the system receives any of the following shut- down inputs: ■ The brake pedal is pressed. ■ The hood is opened. ■ The shutdown toggle switch is put into the ON position. ■ The pre-programmed run time has elapsed. ■ The button is pressed twice within 3 seconds. short-run/turbo Short run turbo mode keeps the engine running after arriving at you destination for a programmable period of 1, 3, 5 or 10 minutes. This allows the system’s timer to conveniently cool down the turbo
Rattler 369D, 5 © 2003 directed electronics, inc. your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. Please note that it is necessary to keep your proof of purchase. fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation.
4 © 2003 directed electronics, inc. iimmppoorrttaanntt iinnffoorrmmaattiioonn Congratulations on the purchase of your remote start keyless entry system. This system will allow convenient access to your vehicle with the push of a button, as well as remote start and other optional features. Properly installed, this system will provide years of trouble-free operation. Please take the time
22 © 2003 directed electronics, inc. Once the correct wire has been found, solder the small LIGHT GREEN wire off the main connector to it and cover the connec- tion with electrical tape. Repeat this process for the unlock wire but press the switch to the unlock position when testing. Once you have identified the correct wire, solder the LIGHT BLUE wire off the mai
Rattler 369D, 30 © 2003 directed electronics, inc. ttrraannssmmiitttteerr//rreecceeiivveerr lleeaarrnn rroouuttiinnee The system comes with one transmitter that has been taught to the receiver. The receiver can store up to 4 different transmitter codes in memory. Use the following learn routine and the infor- mation in the Features Menu to add transmitters to the system or to change button assignments if desired. The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequenc
Rattler 369D, 24 © 2003 directed electronics, inc. If the idle is too slow or too high, the system will shut down the engine to prevent damage. If the starter does not crank long enough to actually start the engine, it is possible to change the programming to extend the crank time. Refer to the Programming Options section of this guide. On some vehicles the electrical system has too low of a voltage variance for the remote start module to see. In this case the engine will not be protected from over cranking, over revolution, or under revolution of the engine. If this is the case, it will be
Rattler 369D, 10 © 2003 directed electronics, inc. iinnssttaallllaattiioonn Be sure to read this section thoroughly and view the Rattler Do- It-Yourself Installation Video in its entirety before starting the installation. Pay special attention to all warnings to prevent personal injury or damage to your vehicle. Visit our 24-hour technical Web site ( wwwwww..ddiiyyrraattttlleerr..ccoomm ) to get a vehicle-specific wiring guide prior to starting this installation. If at any time during the installation you are unable to answer your questions on the Web site, call 11--880000--887733--11331144 for live technical assistance. warn
Rattler 369D, 31 © 2003 directed electronics, inc. button two Channel 2 button three Remote Start + buttons one and two Timer mode + button one and three Short-Run/Turbo 3. TTrraannssmmiitt . While holding the Program switch, press the button on the transmitter that you would like to control the selected receiver channel. 4. RReelleeaassee . Once the code is learned, the Program switch can be released. CHANNEL NUMBER FUNCTION 1 Auto-Learn 2 Lock/Unlock 3 Channel 2 output 4 Remote Start 5 Turbo/Short Run 6 Timer Mode 7 Delete all Transmitters
Rattler 369D, 41 © 2003 directed electronics, inc. authorized dealer. Unless otherwise specified, the buttons used in all of the instructions in this manual correspond to a Standard Configuration transmitter. standard configuration BBuuttttoonn The door locking and unlocking functions are controlled by pressing . BBuuttttoonn The channel 2 output or trunk release is controlled by the button. BBuuttttoonn The remote start function of your system is controlled by pressing . BBuuttttoonnss + When simultaneously pressed these buttons control the timer mode. BBuuttttoonnss + When simultaneously presse
Rattler 369D, 25 © 2003 directed electronics, inc. Have a second person press the gas pedal to increase the RPMs and watch the meter display. When the RPMs increase the voltage should read between 1.5 volts and 2.9 volts. Once the correct tachometer wire has been identified, turn the vehicle off. Run the VIOLET/WHITE wire through the firewall along side the hood pin wire. Then run it into the engine compartment through the factory rubber grommet used for the hood pin. Using a sharp pointed object poke thru the hole in the grommet and attach the VIOLET
Rattler 369D, © 2003 directed electronics, inc. the vehicle starts in gear, cease remote start operation imme- diately and consult with the Dealer to fix the problem imme- diately. ➤ After the remote start module has been installed, test the remote start module in accordance with the Safety Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or properly reinstalled so that the vehicle does not start in gear. OP
SECO-LARM Enforcer SK-910R3-4Q Car Alarm Installation manual
Enforcer SK-910R3-4Q |
Directed Electronics Intelliguard 850 Car Alarm Owner's manual
Intelliguard 850 |
Viper Model 3002 Car Alarm Owner's manual
Model 3002 |
Avital AMX58 Car Alarm Owner's manual
AMX58 |
Clifford IntelliPage IntelliPage System Car Alarm Car Alarm Owner's manual
IntelliPage IntelliPage System Car Alarm |
Prestige Prestige Platinum 128-8122 Car Alarm Owner's manual
Prestige Platinum 128-8122 |
Viper 591XV Car Alarm Owner's manual
591XV |
Rattler 250 Car Alarm Owner's manual
250 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Arrow Group Industries | EH108-A | Owner's manual & assembly instructions | arrow-group-industries/eh108-a-5K5.pdf | 29 Sep 2022 | 32 | |
2 | Mitsubishi Electric | VS-50FD10U | Operation & user’s manual | mitsubishi-electric/vs-50fd10u-P24.pdf | 20 Jul 2022 | 16 | |
3 | GPX | R055B | Operation & user’s manual | gpx/r055b-1RV.pdf | 18 May 2023 | 6 | 0.91 Mb |
4 | Freedom9 | G2400 | Operation & user’s manual | freedom9/g2400-5VU.pdf | 03 Jul 2022 | 28 | 0.41 Mb |
5 | Philips | AD752 | Quick start manual | philips/ad752-94U.pdf | 02 Apr 2023 | 2 | |
6 | Samsung | PN51D440A5D | Operation & user’s manual | samsung/pn51d440a5d-21B.pdf | 23 Jun 2022 | 1 |
AstroStart
PATENTS PENDINGPATENT NO. CAN. 1.130.426PATENT NO. U.S. 4.345.554 193-113-221-A0REMOTE CONTROL ENGINE STARTERMODEL RS-113For all automatictransmission gas- anddiesel-poweredvehicles. (Carburetormodels require anoptional solenoid.)DO NOT INSTALL ONMANUALTRANSMISSIONVEHICLES.Made in Canada by:ASTROFLEX Inc.
…
RS-113(12 pages) |
Omega
COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT 2004DELUXE KEYLESS ENTRY & REMOTE STARTERFOR AUTOMATIC TRANSMISSION VEHICLES ONLYMARS-22Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT, INC. (the Company),are warranted to be free from defects in materials and workmanship under normal use. If a productsold by the Company proves to be defect …
MARS-22(20 pages) |
Mongoose
Two Way Car Alarm System MONGOOSE EMS 1.7R1ENGLISHUser’s GuideIntroductionThank you for purchasing our Car alarm system.Mongoose EMS 1.7R is a modern car security system, designed and manufactured to ensurethe highest level of security for your car and provide you with a number of convenience features.Please carefully read this manual and follow its instr …
EMS 1.7R(26 pages) |
Ultra Start
WWW.ULTRASTARTERS.COMFCC/ID NoticeThis device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may causeundesired operation.CAUTION: Changes or modifications not expressly approved b …
600 SERIES(4 pages) |
Black Widow Security
1INSTALLATION MANUAL3RP 5-BUTTON SERIESVEHICLE SECURITY SYSTEM WITH NETWORK INTERFACEBefore you begin the installation•Read the INSTRUCTIONS!• Always use a multi-meter when verifyingvehicle wiring.•Before mounting the product,verify withthe customer the desired location for the valetswitch and LED.•Protect the vehicle by using fendercovers.•Always …
BW 4150(12 pages) |
Ultra Start
WWW.ULTRASTARTERS.COM250025002500MINSTALLATION GUIDEAdvanced Remote Vehicle Starter & AlarmTECH SUPPORTWestern Canada 1 800 279-0636United States: 1 866 698-5872Eastern Canada. Bilingual Support: 1 800 268-0683 E-Mail Tech Support: [email protected] Our Web Site: www.ultrastarters.com
…
2500 SERIES(16 pages) |
Goldair Grill GBQ45GBQ45 (Grill ePDF Manual, #3Z7VKZ) GBQ45, 19 |
Yamata Sewing Machine FY750FY750 (Sewing Machine ePDF User Guide, #C69NM8) FY750, 51 |
Black Box PCI Card LH1390C-SC-R2LH1390C-SC-R2 Manual - VHB71U LH1390C-SC-R2, 16 |
Weed Eater Lawn Mower 403284PDF Manual (@5H8Y73), Weed Eater 403284 Lawn Mower (11/10/2023) 403284, 30 |
ASROCK Motherboard P55 EXTREMEASROCK P55 EXTREME User Guide (Doc Type: Motherboard Installation manual) P55 EXTREME, 15 |
Sony Camera Accessories VCL-2030 SCamera Accessories #DSOJZL VCL-2030 S, 2 |
Orion Telescope StarBlastStarBlast Instruction manual - X56I99 StarBlast, 5 |
EnGenius Network Router ECB-1220RNetwork Router #6P9DKX ECB-1220R, 69 |
Mega Lite Security Camera Axis Prime 1ORMega Lite Product Manual: Axis Prime 1OR PDF Operation & user’s manual - LW6529 Axis Prime 1OR, 16 |
Viola Systems Receiver H.264H.264 (Receiver ePDF User Manual, #5845JP) H.264, 112 |
Technika Clock Radio DAB-124Technika Clock Radio DAB-124 Owner's handbook manual DAB-124, 20 |
GE Security Security System SimonGE Security Simon User Manual (Doc Type: Security System Operation & user’s manual) Simon, 36 |