Sharp PN-655RU Operation Manual
|
Sharp PN-655RU, 35 E ENGLISH Example: VOLM0030 VOLM 30 (“ ” indicates a space.) * Be sure to input 4 characters for the parameter. Pad with spaces if necessary. Wrong: VOLM30 Right: VOLM 30 (“ ” indicates a space. “ ” is the return code (0D H , 0A H or 0D H ).) When inputting a negative value, specify a numerical value in three digits. Example: AUTR-009 To use the six-digit command (MPOS), use a six-digit numerical value without spaces in between. Example: MPOS010097 If a command has “R” listed for “DIRECTION” in the “RS-232C command table” on page 42, the current value can be returned by using “?” as the parameter. Example: 1. If an ID number has not been
Sharp PN-655RU, 28 F MODE SELECT 3 <MODE SÉLECTION 3> [PIP MODES] <PIP MODE> (Voir à la page 29) Règle la méthode d’affi chage. OFF ····················Affi che un seul écran. PIP ······················Affi che un écran annexe incrusté dans un écran principal. PbyP ···················Affi che un écran principal et un écran annexe sur une ligne. PbyP2 ·················Affi che un écran principal qui mesure 1 280 pixels dans la plus longue direction et un écran annexe sur une ligne. [PIP SIZE] R�
Sharp PN-655RU, 19 F FRANÇAIS Mise sous tension et hors tension Attention • Mettez sous tension le moniteur d’abord avant de mettre sous tension le PC ou l’équipement de lecture. Mise sous tension de l’interrupteur principal Interrupteur principal Lorsque l’interrupteur principal est mis hors tension, le moniteur ne peut pas être mis sous tension en utilisant le bouton POWER (d’alimentation) sur la télécommande. Mise sous/hors tension Appuyez sur le bouton POWER pour la mise sous/hors tension. INPUT Diode d’alimentation Power sur “On”: La diode d’alimentation s’allume en vert. Power sur “Off”: L
Sharp PN-655RU, 40 E Controlling the Monitor with a PC <Response format in Advanced operation > When a command has been executed correctly • Response when no ID number has been set A response is returned when execution of the pertinent command is fi nished. • Response when an ID number has been set When a command has not been executed correctly* • Response when no ID number has been set • Response when an ID number has been set * This is returned when there is no such command, or when the command cannot be used in the current state of the monitor. * If c
Sharp PN-655RU, 22 E Switching the screen size (When the input mode is COMPONENT/VIDEO) Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE ZOOM 1 ZOOM 2 DotbyDot NORMAL Displays the entire image of the aspect ratio of 4:3 without changing the aspect ratio. An image with a 4:3 aspect ratio is stretched to fill the entire screen. Use this size if ZOOM 1 cuts off the subtitles. An image with a 4:3 aspect ratio is enlarged to fill the entire screen without changing the aspect ratio. The edges of the image may be cut off. Displays the dots of the input signals as the cor
20 E Basic Operation Generally the monitor is operated using the remote control unit. INPUT (Input mode selection) The input mode selection menu is displayed. Press or to select the input terminal, and press to change the terminal. * If the remote control unit is not available, you can select the input terminal by pressing the input switch on the monitor with a poi
9 E ENGLISH POWER button (See page 19.) MUTE button (See page 20.) DISPLAY button (See page 21.) MODE button (See page 21.) VOL +/- buttons (See page 20.) BRIGHT +/- buttons (See page 20.) INPUT button (See page 20.) Signal transmitter MENU button (See page 23.) SIZE button (See page 20.) Cursor control ( / / / ) buttons (See page 23.) Part Names
Sharp PN-655RU, 44 F Réglage de l’image (ANALOG) Fonction de la commande Commande Direction Paramètre Réponse Contenu de la commande/de la réponse * ADJUSTMENT <AJUST> AUTO ASNC W 1 Non CLOCK <HEURE> CLCK WR 0 - 255 0 - 255 PHASE PHSE WR 0 - 255 0 - 255 POSITION ECRAN HPOS WR 0 - 255 0 - 255 Règle la position dans la direction la plus longue. VPOS WR 0 - 255 0 - 255 Règle la position dans la direction la plus courte. RESET ARST W 1 GAIN CONTROL <CTRL. LUMINOSIT> AUTO AGIN W 1 Non BLACK LEVEL <NIVEAU NOIR> BLVL WR 0 - 31 0 - 31 Oui CONTRAST <CONTRASTE> CONT WR 0 - 31 0 - 31 WHITE BALANCE <BALANCE COU
Sharp PN-655RU, 21 E ENGLISH Switching the screen size Switching the screen size (When the input mode is DIGITAL/ANALOG) Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE ZOOM 1 ZOOM 2 DotbyDot NORMAL An image with a 4:3 aspect ratio is enlarged to fill the entire screen without changing the aspect ratio. The edges of the image may be cut off. Displays image so it fills the entire screen. Use this size if ZOOM 1 cuts off the subtitles. Displays image so it fills the screen without changi
Sharp PN-655RU, 35 F FRANÇAIS Exemple : VOLM0030 VOLM 30 (“ ” indique un espace.) * Veillez à entrer 4 caractères pour le paramètre. Ajoutez des espaces si c’est nécessaire. Erreur : VOLM30 Exact : VOLM 30 (“ ” indique un espace. “ ” est le code retour (0D H , 0A H ou 0D H ).) Lors de la saisie d’une valeur négative en entrée, spécifi ez une valeur numérique par un nombre à trois chiffres. Exemple : AUTR-009 Pour utiliser la commande à six chiffres (MPOS), utilisez une valeur numérique à six chiffres sans espaces entre les chiffres. Exemple : MPOS010097 Si dans une commande “R” apparaît dans
Sharp PN-655RU, 43 E ENGLISH Picture Adjustment (DIGITAL) Control item Command Direction Parameter Reply Control/Response contents * WHITE BALANCE THRU CTMP WR 00 Yes PRESET 1 - 15 1 - 15 USER 99 99 R-CONTRAST CRTR WR 0 - 255 0 - 255 G-CONTRAST CRTG WR 0 - 255 0 - 255 B-CONTRAST CRTB WR 0 - 255 0 - 255 GAMMA GAMM WR 0 - 2 0 - 2 0:1.8, 1:2.2, 2:2.4 Yes GAIN CONTROL BLACK LEVEL BLVL WR 0 - 60 0 - 60 Yes CONTRAST CONT WR 0 - 60 0 - 60 INPUT RESOLUTION RESOLUTION CHECK PXCK R - Returns current resolution in the form of hhh, vvv. No ENLARGE E
Sharp PN-655RU, 51 E ENGLISH No. 1 2 3 4 5 6 7 8 9 10 11 12 Function TMDS data 2- TMDS data 2+ TMDS data 2/4 shield N.C. N.C. DDC clock DDC data N.C. TMDS data 1- TMDS data 1+ TMDS data 1/3 shield N.C. No. 13 14 15 16 17 18 19 20 21 22 23 24 Function N.C. +5 V GND Hot-plug detection TMDS data 0- TMDS data 0+ TMDS data 0/5 shield N.C. N.C. TMDS clock shield TMDS clock+ TMDS clock- PC digital RGB input terminal pins (DVI-D 24 pin) PC analog RGB input terminal pins (Mini D-sub 15 pin) No. 1 2 3 4 5 Function N.C. Transmitted data Received data Data terminal rea
Sharp PN-655RU, 48 E Warning when temperature rises • When the internal temperature of the monitor rises excessively, the brightness of the backlight decreases automatically in order to prevent high-temperature-related problems. When this occurs, “TEMPERATURE” is displayed on the screen and the Power LED fl ashes red and green alternately. • If the internal temperature rises further, the monitor automatically enters standby mode. (The Power LED continues fl ashing red and green alternately.) Solution: • If the monitor enters standby mode du
Sharp PN-655RU, 41 E ENGLISH If execution of the command is taking some time IWTA Return code (0D H , 0A H ) When the following commands are used, “WAIT” is returned. In this case, a value will be returned if you wait a while. Do not send any command during this period. No ID number is attached to WAIT response. • Commands which return WAIT: - When repeater control is used - When an IDSL or IDLK command is used - When one of the following commands is used: RSET, INPS, ASNC, WIDE, EMAG, EPOS, PXSL, POWR, AGIN, MWIN, MWIP, MWPP. When control via RS-232C is locked (to prevent
Sharp PN-655RU, 36 E Controlling the Monitor with a PC Advanced operation This section explains commands for daisy chain connection. The basic communication procedure is the same as in the “Basic operation” section. <ID numbers> You can assign a unique ID number to each monitor (see page 27). This allows you to control a particular monitor in a daisy chain of monitors. You can assign ID numbers either from the menu screen (using the remote control) or from the PC using RS-232C cable. [Example] ID number: 1 ID number: 2 ID number: 3 ID number: 4 PC If monitors are conn
6 F Table des matières Introduction INFORMATION IMPORTANTE .................................................................................1 CHER CLIENT ...........................................................................................................3 PRÉCAUTIONS DE SÉCURITÉ ................................................................................3 CONSEILS ET MESURES DE
34 F Commande du moniteur par un PC Raccordement d’une série de moniteurs à un seul PC...... Fonctions avancées Connectez le câble direct RS-232C entre le port COM du PC (connecteur RS-232C) et la borne d’entrée RS-232C du premier moniteur. Puis connectez le câble direct RS-232C à la borne de sortie RS-232C du premier moniteur et à la borne d’entrée RS
Sharp PN-655RU, 1 F FRANÇAIS INFORMATION IMPORTANTE PN-655RU MONITEUR LCD FRANÇAIS IMPORTANT : Pour faciliter la déclaration de perte ou de vol, veuillez noter les numéros de modèle et de série de l’appareil dans l’espace prévu à cet effet. Vous trouverez ces numéros au dos de l’appareil. N° de modèle : N° de série : ÉTATS-UNIS SEULEMENT AVERTISSEMENT: POUR RÉDUIRE LE RISQUE D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, NE PAS EXPOSER CE PRODUIT À LA PLUIE OU À LA POUSSIÈRE. RISQUE DE DÉCHA
Sharp PN-655RU, 40 F <Format des réponses dans les fonctions avancées > Lorsqu’une commande a été exécutée correctement • Réponse quand aucun numéro d’identifi cation n’a été affecté Une réponse est renvoyée lorsque l’exécution de la commande pertinente est terminée. • Réponse quand un numéro d’identifi cation a été affecté Lorsqu’une commande n’a pas été exécutée correctement* • Réponse quand aucun numéro d’identifi cation n’a été affecté • Réponse quand un numéro d’identifi cation a été affecté * Ce message est renvoyé quant une telle commande n’existe pas, ou quand
Sharp PN-655RU, 32 F Initialisation (Restauration)/Réglage des restrictions des fonctions Vous pouvez restaurer le contraste, la qualité de l’image et d’autres réglages en leurs valeurs préréglées à la sortie d’usine, spécifi er si les diodes d’alimentation s’allument, et permettre la commande via RS-232C (voir à la page 33) parmi d’autres fonctions. 1. Après avoir appuyé sur pendant environ 5 secondes, appuyez sur , , , et sur dans cet ordre. L’écran FUNCTION 1 va apparaître. ALL RESET ADJUSTMENT LOCK OSD DISPLAY LED RS-232C OFF OFF OFF LOCKED ALL RESET 1 2 ON ON UNLOCKED FUNCTION 1 2. Sélec
Sharp PN-655RU, 52 E Unit: inch [mm] Dimensional Drawings Note that the values shown are approximate values. Opening width (31- 3 /4 [807]) 34- 5 /16 [871] Opening height (56- 3 /8 [1432]) 61- 7 /8 [1572] 5- 7 /8 [150] 1 /4 [6] 1- 9 /16 [40] 1- 9 /16 [40] 59- 7 /16 [1509] 17- 5 /16 [440] 39- 1 /2 [1003] 36- 5 /16 [923] 25- 9 /16 [650] Screw holes for mounting brackets When mounting the monitor, read the manual of the brackets or stand for their mounting procedure. The screw holes for mounting brackets (M10 x 4 holes) are provided on the rear of the monitor. Note that scre
Sharp LC 42D43U - 42" LCD TV Flat Panel TV Operation manual
LC 42D43U - 42" LCD TV |
Sharp AQUOS Z41G460184301A Flat Panel TV Operation manual
AQUOS Z41G460184301A |
Sharp AQUOS D65U Series Flat Panel TV Specification sheet
AQUOS D65U Series |
Sharp AQUOS LC-60E88UN Flat Panel TV Operation manual
AQUOS LC-60E88UN |
Sharp LC-30HV6U Flat Panel TV Operation manual
LC-30HV6U |
Sharp LC-42BD80U Flat Panel TV Operation manual
LC-42BD80U |
Sharp Aquos LC-32D59U Flat Panel TV Operation manual
Aquos LC-32D59U |
Sharp Aquos LC 32GD9E Flat Panel TV Operation manual
Aquos LC 32GD9E |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Dell | Alienware 14 | Specifications | dell/alienware-14-3W9.pdf | 08 May 2023 | 1 | 2.68 Mb |
2 | Yamaha | C-6 | Owner's manual | yamaha/c-6-5S7.pdf | 25 Apr 2023 | 12 | 1.83 Mb |
3 | IPUX | ICS1330 | Installation manual | ipux/ics1330-EV8.pdf | 17 Jul 2022 | 67 | |
4 | Directed Electronics | 259D | Operation & user’s manual | directed-electronics/259d-Y5D.pdf | 28 Dec 2023 | 49 | 1.04 Mb |
5 | Polaris | Hawkeye 2x4 | Owner's manual | polaris/hawkeye-2x4-5X2.pdf | 21 Sep 2022 | 134 | |
6 | Ferris | IS1500Z | Operator's manual | ferris/is1500z-Y5G.pdf | 19 Feb 2024 | 52 |
Toshiba
LEADING THE WAY IN HOME ENTERTAINMENT INNOVATION46XV645U1080p Full HD LCD TVwith ClearFrame™ 120HzLEADING THE WAY IN HOME ENTERTAINMENT INNOVATION46XV645U 46.0” diagonal 1080p HD LCD TV with ClearFrame™ 120HzPRELIMINARYADVANTAGE• 1080p Full HD CineSpeed™ Display• ClearFrame™ 120Hz with 5:5 Pull-Down Option• 50,000:1 Dynamic Contrast Rati …
46XV645(2 pages) |
Philips
55PFL7705DV55PFL7705D46PFL7705DV46PFL7705D40PFL7705DV40PFL7705DMODEL NUMBER SERIAL NUMBERPHILIPS WIRELESS MEDIACONNECT KEY CODELea esta manual antes de usar el productoRegister your product and get support atwww.philips.com/welcomeEN User Manual FR Manuel d’Utilisation ES Manual del Usuario EN: For further assistance, call the customer support service i …
40PFL7705D(48 pages) |
Toshiba
47HL16747” Diagonal REGZA™LCD TVPRELIMINARY1080p Full HD Display - With Full HD, there’s no need to scale down a 1080 signal. With twice the pixel resolution of 720p HDmodels, Full HD creates the pinnacle in picture quality.ColorBurst™ - ColorBurst™ significantly increases the LCD color space to reproduce 90%+ of the NTSC Color Gamut.By utilizing p …
47HL167 - 47" LCD TV(2 pages) |
Samsung
PLASMA DISPLAYFP-T5084FP-T6374Owner’s InstructionsRegister your product at www.samsung.com/global/registerRecord your Model and Serial number here for future reference.▪ Model _______________ ▪ Serial No. _______________BN68-01094P-00Eng.indb 1 2007-04-13 ¿ÀÈÄ 5:30:41
…
FPT5084 - 50" Plasma TV(83 pages) |
Sony
LCD DIGITAL COLOR TELEVISION SERVICE MANUAL FIX2 CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION 9-883-764-04KDL-40VL130 RM-YD014 US KDL-52W3000 RM-YD017 US/CNDKDL-52WL130 RM-YD017 USKDL-52WL135 RM-YD014 USHISTORY INFORMATION FOR THE FOLLOWING MANUAL:ORIGINAL MANUAL ISSUE DATE: 8/2007☛:UPDATED ITEMREVISION DATE SUBJECT 8/2007 No revis …
KDL-40VL130(188 pages) |
Seiki
1Composite Video Input 2Demodulation:8VSB,64QAM,256QAMSupport HDMI 1.3 HDCP 1.1USB Supports File Format MPEG-1/-2,MP3,JPEGOSD Language 3 options of English/French/SpanishAnalog&Digital TV Tuner181 channel1920 x 1080 @ 120HzRCA Output(Red, White)NAHeadphone: Stereo Mini 131360 x 768 @ 120HzAudioMaximum Audio OutputUSB1280 x 1024 @ 120HzElectronics4S-Video …
LC-55TD5(1 pages) |
Orima Kitchen Appliances ORS 222Kitchen Appliances #C4434R ORS 222, 9 |
SCAN Stove 68-16SCAN 68-16 Guide (Doc Type: Stove Assembly and instruction manual) 68-16, 40 |
Yamaha Electronic Keyboard PSS-140PSS-140 Owner's manual - UZ8GNQ PSS-140, 31 |
DECKED Automobile Accessories MG3Automobile Accessories Installation instructions manual (DECKED MG3) MG3, 19 |
Eduard Toy F6F-3F6F-3 Quick start manual - 8VO7OC F6F-3, 8 |
LevelOne Switch OfficeCon GSW-0841Switch Specifications (LevelOne OfficeCon GSW-0841) OfficeCon GSW-0841, 3 |
Rolls Stereo Receiver ADB3bUser Guide: Rolls ADB3b (N8PXB4, Upd.03rd Nov 2023) ADB3b, 1 |
Epson All in One Printer CX7000F - Stylus Color InkjetEpson All in One Printer CX7000F - Stylus Color Inkjet Supplement CX7000F - Stylus Color Inkjet, 1 |
Barska Safes DX SeriesManual: Barska DX Series (MLMLP7, Upd.27th Feb 2024) DX Series, 2 |
Hotpoint Oven BS43B/1Oven Operating instructions manual (Hotpoint BS43B/1) BS43B/1, 12 |
Acer Desktop Altos G5450#3141D4 Altos G5450: Acer Desktop Owner Documentation Altos G5450, 150 |
Sunricher Remote Control SR-1009XXSunricher SR-1009XX User Guide (Doc Type: Remote Control Operation & user’s manual) SR-1009XX, 2 |