Manualios.com

GE NetworX NX-7002 Installation Manual

GE NetworX NX-7002 Manual Online:

4.8, 2555 votes
GE NetworX NX-7002 User Manual
GE NetworX NX-7002 User Guide
GE NetworX NX-7002 Online Manual

Text of GE NetworX NX-7002 User Guide:

  • GE NetworX NX-7002, LOC PG DESCRIPTION DEFAULT PROGRAMMING DATA DEVICE STATUS FLAGS (read only) Segment 1 1 On = Communication with GSM modem OK 2 On = SIM card PIN is OK 3 On = Logged in to the GSM network 4 On = Sending SMS 5 On = Using GSM audio connection 6 On = Using GSM CSD connection 7 On = Connected to GPRS network 8 On = SIM card PUK code required Segment 2 1 On = Battery voltage failure 2 On = GSM PSU voltage failure 3 On = Bus voltage failure 4 On = Communication channel failure 5 On = U/D session in progress 6 On = U/D session starting 7 On = Reporting in progress 8 On = Good RSSI Level Segment 3 1 On = Max reports in 24h li

  • GE NetworX NX-7002, www.gesecurity.com EMEA Distribution is a division of GE Security EMEA bvba COPYRIGHT ©2005 © GE Security EMEA bvba. All rights reserved. GE Security EMEA bvba grants the right to reprint this manual for internal use only. GE Security EMEA bvba reserves the right to change information without notice. NX-7002 Installation manual Page 39 09/02/05

  • GE NetworX NX-7002, LOCATION 144 TCP/IP 2 LINE NUMBER (4 segments) See location 141. LOCATION 145 SMS 1 ACCOUNT NUMBER (8 segments) The SIA account number used for SMS reporting. SIA account numbers are 6 digits long. Enter the first digit of the SIM PIN code in segment 3 (segment 1 and 2 are not used). Press * to move to the next segment. Continue in this way until all digits are programmed. LOCATION 146 SMS 2 ACCOUNT NUMBER (8 segments) See location 145. LOCATION 147 – LOCATION 153 RESERVED LOCATION 154 ACCOUNT NUMBER FOR PARTITION 1 (8 segments) The account code sent when partition 1 is reported.

  • GE NetworX NX-7002, GENERAL INFORMATION The NX-7002 is the GPRS module that can be added to the NetworX range of panels (NX-8- EUR, NX-6-EUR and NX-4-EUR). The NX-7002 GPRS module features include: • Wireless event reporting. • Six programmable report destinations. • Selectable reportable events from eight partitions. • Compatible with PSTN or ISDN reporting. • PSTN/ISDN as backup. • SIA and Contact ID reporting over GPRS, towards Osborne-Hoffman OH2000 TPC/IP receiver. • SIA reporting with optional area modifiers using SMS messages. • The control panel can use GSM in addition to PSTN

  • GE NetworX NX-7002, LOC PG DESCRIPTION DEFAULT PROGRAMMING DATA EVENT SELECTION FOR REPORT CONTROL 4 (BY PARTITION) Segment 1 Alarms and Restores 0-0-0-0-0-0-0-0 Segment 2 Open/Close 0-0-0-0-0-0-0-0 Segment 3 Bypass 0-0-0-0-0-0-0-0 Segment 4 Zone Trouble 0-0-0-0-0-0-0-0 Segment 5 Power Trouble (AC Failure / Low Batt.) 0-0-0-0-0-0-0-0 Segment 6 Siren & Telephone Fault 0-0-0-0-0-0-0-0 Segment 7 Test Reports 0-0-0-0-0-0-0-0 Segment 8 Program, Download, & Log Full 0-0-0-0-0-0-0-0 Segment 9 Tampers (zones and box) 0-0-0-0-0-0-0-0 Segment 10 Short Circuit 0-0-0-0-0-0-0-0 Segment 11 Sensor Lost 0-0-0-0-0-0-0-0 Segment 12 Sensor

  • LOCATION 4 EVENT SELECTION FOR REPORT CONTROL 1 BY PARTITION (16 segments, feature selection data) All events for report control 1 are enabled by default. Select the partition(s) to include in the event report. Enabled events are formatted into one or more messages according to pre- configured settings and sent to the selected report destination

  • GE NetworX NX-7002, NX-7002 LAYOUT AND DESCRIPTION 9 8 1 2 3 4 1 1 11 10 7 5 7 6 DESCRIPTION 1 Future use (VVMIQ) 2 SIM card holder 3 GPRS modem 4 Connect antenna to this connector 5 Header for software upgrade 6 Connect to battery 7 Connect main panel battery leads to these connectors 8 Audio tap connector (CON5) If the NX-7002 uses the voice channel for event reporting, the special audio cable (included) needs to be stuffed between this connector of the NX-7002 and the Audio Tap connector of the control panel. 9 Keypad bus terminals 10

  • LOCATION 164 SMS 1 FORMAT (1 segment) The communicator format used to transmit to the SMS 1 report destination from the NX-7002 GPRS module. Consult the instructions for your central station receiver to determine which format is compatible. SIA reporting over SMS can be set to one of three modes: DATA FORMAT 0 SIA Separate Events 1 SIA Combined Events 2 SIA with Area M

  • GE NetworX NX-7002, PROGRAMMING THE LOCATIONS LOCATION 0 MODULE MODE OF OPERATION FEATURE SELECTION (8 segments) This location contains the system characteristics. Segment 1 1 = Enable site initiated downloading (*98 from a keypad) 2 = Enable remote initiated downloading This setting enables the PC to dial into the NX-7002. It is dependent on other settings (segment 3, 5 and 6). 3 = Remote initiated download must be from known source If enabled, program the phone number of the PC in location 168. 4 = Enable remote download at test time This setting configures the NX-7002 to automatic

  • GE NetworX NX-7002, LOCATION 165 SMS 2 PHONE NUMBER (20 segments) See location 163. LOCATION 166 SMS 2 FORMAT (1 segment) See location 164. Note: By default, not more than 20 SMS messages will be transmitted in a 24 hour time period. If needed, this number can be changed (see location 162 segment 3). LOCATION 167 SMS SERVICE CENTRE NUMBER (20 segments) This number is mandatory when SMS reporting is used. Usually the SIM card automatically dials this number. “14” indicates the end of the phone number. Program “11” to insert “*” in

  • NX-7002 FOR PRIMARY OR BACKUP REPORTING NX-7002 for primary reporting The NX-7002 can be configured to be the primary transmitter. In this case, the NX-7002 acts as the main alarm reporting device. If the NX-7002 fails, for example, if there is no GSM coverage or there is jamming, if the network of the provider is down or there are technical problem

  • GE NetworX NX-7002, LOCATION 174 DEVICE STATUS FLAGS (2 segments) This location contains specific status information of the GSM/GPRS module. If the option is ”On”, the status condition is true. Segment 1 1 = On: Communication with GSM modem OK 2 = On: SIM card PIN is OK 3 = On: Logged in to the GSM network 4 = On: Sending SMS 5 = On: Using GSM audio connection 6 = On: Using GSM CSD connection 7 = On: Connected to GPRS network 8 = On: SIM card PUK code required Segment 2 1 = On: Battery voltage failure The NX-7002 measure

  • GE NetworX NX-7002, Enrolling the SIM card on the GSM network • Insert the SIM card. See Inserting the SIM card for more information. • Power up the NX-7002 GPRS module. • Enter programming mode. See Programming he NX-7002 GPRS module for more information. • Press 78# to select the module. • Press 169# to enter the GSM SIM PIN code location. • Enter the first digit of the SIM PIN code. Press * to move to the next segment. Continue in this way until all digits are programmed. Press # to save the changes and exit the location. • Exit programming mode. The SIM is automatically enrolled on the GMS network. Note: Each time you exit programming mode, the mo

  • GE NetworX NX-7002, APPENDIX 2: OPERATOR ID CODES This appendix provides a list of operator codes and the associated operator name. Operator name Network name ID code On mobile phone Belgium Proximus Belgacom Mobile Proximus 20601 BEL PROXIMUS Mobistar Mobistar 20610 B Mobistar Base Base 20620 Base Denmark TDC Mobil A/S TDC Mobil 23801 DK TDC Sonofon SONOFON 23802 SONO Hi3G Denmark ApS 3 DK 23806 3 DK Telia A/S Denmark TELIA DK 23820 TELIA Orange A/S Orange 23830 Orange France Orange France Orange F 20801 F-FT SFR SFR 20810 SFR Bouygues Telecom Bouygues Telecom 20820 BOUYGTEL Germany T-Mobile Deutschland GmbH D1 26201 TMO D Vodafone

  • LOCATION 12 EVENT SELECTION FOR REPORT CONTROL 3 BY PARTITION (16 segments, feature selection data) All events for report control 3 are disabled by default. See location 4. LOCATION 13 DESTINATION SELECTION FOR REPORT CONTROL 4 (1 segment) This location contains the report destination for report control 4. See location 1. LOCATION 14 BACKUP DESTINATION S

  • GE NetworX NX-7002, SIM card PUK code See PUK code SMS Short Message Service. SMS is a service for sending short text messages to mobile phones (see locations 1, 145, 163, 164, 167). Transparent mode Data is transferred directly from one modem to another modem (see location 0 segment 1). NX-7002 Installation manual Page 6 09/02/05

  • GE NetworX NX-7002, LOC PG DESCRIPTION DEFAULT PROGRAMMING DATA 154 20 Account number partition 1 0-0-0-0-0-0-0-0 155 20 Account number partition 2 0-0-0-0-0-0-0-0 156 20 Account number partition 3 0-0-0-0-0-0-0-0 157 20 Account number partition 4 0-0-0-0-0-0-0-0 158 20 Account number partition 5 0-0-0-0-0-0-0-0 159 20 Account number partition 6 0-0-0-0-0-0-0-0 160 20 Account number partition 7 0-0-0-0-0-0-0-0 161 20 Account number partition 8 0-0-0-0-0-0-0-0 TIMERS AND COUNTERS Segment 1 Max Number of network attempts 8 Segment 2 Report attempts for Fail To Communicate 4 Segment 3 Maximum rep

  • GE NetworX NX-7002, APPENDIX 1: REPORTING FIXED CODES IN CONTACT-ID AND SIA The table below lists the event codes sent for the following reports (if enabled) when using Contact ID or SIA formats. REPORT CONTACT ID SIA MANUAL TEST 601 RX AUTOTEST 602 RP OPEN (User Number) 401 OP CLOSE (User Number) 401 CL CANCEL (User Number) 406 OC DOWNLOAD COMPLETE 412 RS START PROGRAM 627 LB END PROGRAM 628 LX RECENT CLOSE (User Number) 401 CR EXIT ERROR (User Number) 457 EE EVENT LOG FULL

  • GE NetworX NX-7002, Operator name Network name ID code On mobile phone Spain Vodafone Espana S.A. Vodafone 21401 E VODAF Retevision Movil S.A AMENA 21403 RET MOV, E 03, AMENA Telefonica Moviles Espana S.A. MOVISTAR 21407 MSTAR Sweden TeliaSonera Mobile TELIA MOBILE 24001 TELIA HI3G Access AB 3 24002 3 Tele 2 AB COMVIQ 24007 IQ Vodafone Sverige AB Vodafone 24008 voda SE Swefour AB Swefour AB 24010 Spring United Kingdom O2 (UK) Limited O2 23410 O2 -UK Vodafone Ltd Vodafone 23415 Voda Hutchison 3G UK Ltd 3 23420 3 UK T-Mobile (UK) Limited T-Mobile

  • GE NetworX NX-7002, INSTALLATION GUIDELINES • Avoid installing the module: - Where temperatures exceed 49°C or fall below 0°C. - In the immediate vicinity of electronic equipment. - In humid rooms. The module is not hermetically sealed and excess moisture on the circuit board can eventually cause an electrical fault. • Keep the antenna within 2 m of the panel. • Before permanently mounting the module, test it at the intended location to ensure that the remote alarm receiver can receiv

  • GE NetworX NX-7002, PROGRAMMING HE NX-7002 GPRS MODULE Programming the NX-7002 via the LED keypad ENTERING THE PROGRAM MODE To enter the program mode, press [*]-[8]. At this time, the five function LED’s (Stay, Chime, Exit, Bypass and Cancel) will begin to flash. Next, enter the “Go To Program Code” (factory default is [9]-[7]-[1]-[3]). If the “Go To Program Code” is valid, the “Service” LED will flash and the five function LED’s will illuminate steady. You are now in the program mode

Related Products and Documents (Cell Phone):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Chauvet Colorado 1-Quad Tour Quick reference manual chauvet/colorado-1-quad-tour-L3N.pdf 06 Jul 2023 22
2 LG Motion 4G MS770 Owner's manual lg/motion-4g-ms770-Q14.pdf 07 Apr 2023 385
3 HTC Windows Mobile 6 Software Warranty statement htc/windows-mobile-6-software-PRQ.pdf 08 Jul 2022 79
4 Comdial ExecuTech 2000 Operation & user’s manual comdial/executech-2000-V28.pdf 07 Sep 2023 63
5 Bellman & Symfon Visit Operation & user’s manual bellman-symfon/visit-N51.pdf 16 Mar 2024 3
6 Alpine CDA-9885 Owner's manual alpine/cda-9885-RDF.pdf 16 Jun 2023 118 7.23 Mb

Similar Resources:

  • LG

    exalt LTE

    (2 pages)
    Key Functions1. Home Screen Displays messages, indicator icons, and active functions.2. Left soft key Allows you to select the command at the lower left area ofthe display screen.3. Speakerphone key Allows you to enable or disable the speakerphonemode. (Speakerphone available only while on call).4. Send key Allows you to make and answer calls. Press from st …
  • Motorola

    Moto e5 cruise

    (2 pages)
    Getting to know your moto e5 cruiseLet’s get started. We’ll guide you through startup and tell you where to find more information about your phone and its great features.Quick Start GuideAPRTUE37311:3573VolumeFlashHeadsetSpeakerMicrophoneMicro USB/ChargerPowerSIM & microSD Card SlotsFront CameraPhone setupInserting the battery, nano SIM card, and mi …
  • Just5

    Freedom C100

    (2 pages)
    INSERT SIM CARDThe phone is a Dual SIM mobile phone allowing you to use the facility of two networks.To insert USIM/SIM card(s):1. Switch off the mobile phone and remove the rear cover and battery.2. Insert the USIM/SIM card correctly in the card slot(s).3. Finally insert the battery and put the rear cover back on, check it is pressed correctly. Turn the dev …
  • Zte

    Blade V2 (A476)

    (10 pages)
    1 ZTE Blade V2 (A476) Quick Start Guide ZTE Australia is on Facebook , Google+, Twitter and Instagram Copyright © 2015 by ZTE Corporation. AU Ver 1.0 Oct. 2015 Front camera Display Options key Home key Back key Back camera Volume keys Flashlight Power key Microphone Card tray Headset jack Noise-reduction MIC Speaker Ea …
  • TCL

    PLEX T780H

    (97 pages)
    For more information on how to use the phone, please go to tcl.com and download the complete user manual. Moreover, on the website, you can also find answers to frequently asked questions. …
  • Samsung

    STH-N275

    (61 pages)
    NNeed to checkQ107, Q106NReplace dome S/WNNeed to checkQ107, Q106NNeed to replaceMemory(U202)NNeed to check neighbor partNeed to check OSC320,Y201 & neighbor partSAMSUNG Proprietary-Contents may change without notice1-11. Trouble Shooting1. Baseband Section1-1. Program No RunningPress END KeyYYYYYYON_SW=HVBAT>3.2VVCTCXO_IN=14.4MHz32K_XIN=32.768 kHZMe …

Comments, Questions and Opinions: