GE 1018959 Operating Manual

Text of GE 1018959 User Guide:

• 3 WEB INTERFACE 3.1 INTRODUCTION The SNMP/Web adapters provide a web interface by implementing an embedded web server. This interface allows to configure the adapter in order to monitor and manage the UPS. 3.1.1 Supported browsers The use of non-standard / deprecated HTML tags has been avoided in order to guarantee compatibility with the most commonly used

• 5.3 DNS CONFIGURATION DNS configuration affects the SNMP/Web adapter ability to resolve symbolic hostnames to IP addresses, and may impact other functionality (such as e-mail sending, for example): The SNMP/Web adapters can be configured to automatically obtain DNS server address (e.g. Primary and Secondary DNS server as specified in the DHCP response). This is the d

• Setting the boot-method to manual has the side effect that manual-dns is also set to ON. Mind that the reverse is not true (setting boot-method to DHCP does not forced manual-dns to OFF). However, if the boot method is set through the quick network configuration menu, setting the boot-method to DHCP will also force manual-dns to OFF. Unlike network setti

• GE 1018959, On the console interface inject the ssl-fingerprint command. Below is a sample output of the ssl- fingerprint command: GEDE> ssl-fingerprint MD5 Fingerprint=8F:A1:CE:8B:B3:04:E7:07:90:6D:02:77:6F:EE:9E:22 SHA1 Fingerprint=F5:D2:CA:27:BF:DA:98:31:39:6F:18:8C:C5:9C:BC:6C:D3:62:15:AC It can be seen that the thumbprint shown by the web browser (with thumbprint algorithm shown as sha1) matches the SHA1 fingerprint as shown by the ssl-fingerprint command. Furthermore, the SNMP/Web adapters are provided with two different certificates: the server certificate and t

• GE 1018959, • Most SSH clients display the host key fingerprint at the start of the session. Make sure the fingerprint shown matches the SNMP/Web adapter fingerprint (see Encryption section for details on figuring out the SSH fingerprint) • A login window should then be available in a few seconds. The default username (login) and password are ge and ge 2.1.3 Log-on User authentication requires inputting the username and password. Remember that: • Both username and password are case-sensitive, and are always specified in lower case •

• GE 1018959, 2.2.10 UPS command group The UPS command group allows monitoring and configuration of the managed UPS system. Command Parameters Description upsinfo (*) Show detailed UPS information upstest (*) Start/Stop UPS tests upscontrol (*) Control the UPS (1-ph/SP versions ONLY) upsconfig (*) Configure UPS parameters attacheddevice [device] Set UPS attached device [device] Device which is powered/protected by the UPS NOTE: Maximum length 63 chars. If this parameter contain blanks or special characters it shall be specified in between double quotation marks (“...”) alarmdelay [time] Set a

• GE 1018959, GE Digital Energy Power Quality Operating Manual Digital Energy™ SNMP / WEB ADAPTER P/N 1018959 3-ph SNMP/Web plug-in adapter P/N 1019070 1-ph SNMP/Web plug-in adapter P/N 23954 SP SNMP/Web plug-in adapter P/N 1019071 1-ph SNMP/Web external adapter GE Consumer & Industrial SA General Electric Company CH – 6595 Riazzino (Locarno) Switzerland T +41 (0)91 / 850 51 51 F +41 (0)91 / 850 51 44 www.gedigitalenergy.com GE imagination at work

• GE 1018959, Finally, a 3-ph system featuring the PMAD functionality will also show the following: Parameter Name Description Power factor The present output power factor. A positive value indicates an inductive load; while a negative value indicateS a capacitive load. Note: the power factor cannot be reliably determined in low load conditions. In this case, the value will not be available (N/A) Peak current The output peak current Share current In a parallel system ideally all the UPS are requested to contribute to the

• GE 1018959, 4.3 GE MIB OBJECTS GE provides private MIBs, which enhance the UPS information available over SNMP interface. These MIBs are only supported on 3-ph SNMP/Web plug-in adapter. Two different version of the GE private MIB exist: • GE Single MIB : to be used for monitoring of a 3-ph UPS is single unit configuration • GE Parallel MIB : to be used for monitoring of a 3-ph parallel UPS system The MIB structure is shown in the following picture. The geGenericUPS group provides information on the unit in stand-alone configuration or on the overall sys

• GE 1018959, 1 INTRODUCTION 1.1 FEATURES Each SNMP/Web adapter provides the following features: • 10/100 Mpbs connection speed • Use of DHCP / BOOTP or manual configuration for the TCP/IP network settings • SNMP Agent • Web server • Console interface • UPS status / alarms / readings, alarm logging over different interfaces • Digital outputs (open-collector outputs for relay drive) – 1-ph plug-in version only • SNMP Traps and E-mail notification upon UPS alarm • Multi-server network shutdown • Modbus TCP slave (license

• GE 1018959, Modifications reserved Page 2/69 OPM_CNT_SNM_BAS_CRD_1GB_V014.doc Operating Manual SNMP/Web Adapter Model: 3-ph SNMP/Web plug-in adapter 1-ph SNMP/Web plug-in adapter SP SNMP/Web plug-in adapter 1-ph SNMP/Web external adapter Date of issue: 06.Jul.2010 File name: OPM_CNT_SNM_BAS_CRD_V014 Revision: 1.4 Identification No. P/N 1018959 P/N 1019070 P/N 23954 P/N 1019071 Up-dating Revision Concerns Date 1.0 First Issue 15.02.2008 1.1 Updated for the 3-ph and SP SNMP/Web plug-in adapters 13.05.2008 1.2 Updated following the introduction of the RCCMD functionality 05.12.2008 1.3 Introd

• GE 1018959, 1 3 Rear View 6 7 • 1 – RJ45 Connector Ethernet connection, 10Base-T or 100Base-TX • 2 – LEDs Ref. specific section • 3 – RS-232 port Local console connection (115200-N-8-1) • 4 – Reset button HW reset • 6 – Power-in AC adapter connection • 7 – UPS port RS-232 connection to the UPS LEDs The various front panel LEDs have the following meaning: • LAN / Netlink Status Meaning Off No LAN connection detected On LAN connection established, no communication Blink LAN c

• 1-ph SNMP/Web plug-in adapter (P/N 1019070) Reset RS-232 UTP 10/100 Active LAN Contact interface UPS Reset RS-232 UTP 10/100 Active LAN Contact interface UPS Front Panel – User Interface anual SNMP/Web Adapter • 1 – RJ45 Connector Ethernet connection, 10Base-T or 100Base-TX • 2 – LEDs Ref. specific section • 3 – RS-232 port Local con

• Output Frequency 50.0 Hertz: exponent –8 (F8h), mantissa 12’800 (00 32 00h), coded value F8 00 32 00 F8 00 32 00 00 32 00 h = 12800mantissa F8 h = -8exponent 2 12800 x 2 -8 = 50.0 Output Power 1370 Watts: exponent 0 (integer value), mantissa 1’370 (05 5Ah), coded value 00 00 05 5A 00 00 05 5A 00

• GE 1018959, 3.3.2 Battery page The Battery page shows the following information. Parameter Name Description Battery Status The current status of the battery: 1 – unknown 2 – normal The remaining run-time on batteries is greater than the UPS low battery time (ref. UPS Config page) 3 – low The remaining run-time is less than or equal the UPS low battery time (ref. UPS Config page) 4 – depleted The battery would be unable to sustain the load, if mains power is lost Seconds On Battery T

• GE 1018959, 2.2.4 User command group The user command group is available only to the supervisor user, the only user who can perform user management. Command Parameters Description supername [name] Change supervisor login name [name] New supervisor username NOTE: By default, the superuser is the only configured user with username and password set to ge and ge. showuser Show user settings adduser [user] [http] [telnet] [ftp] [access] Add a user [user] username for the new user [telnet] 1 – access allowed / 0 – not allowed [http] 1 – access allowed / 0 – not allowed [ftp] 1 – access allowed / 0 – not allowed [access] ‘ro’ – read-only / ‘rw�

• GE 1018959, 3.6 SNMP SECTION The SNMP section deals with SNMP and trap configuration. 3.6.1 SNMP settings page The most relevant SNMP settings are the following: Parameter Name Description Port Number Set SNMP server listening port. Default port is 161. Get Community Defines the community name for receiving SNMP information (GET). The get community name controls access to the SNMP Agent – the community in the request must match the getcommunity parameter. The default value is public. Set Community Defines the community name for writing SNMP information (SET). The set community name controls access to the SNMP Agent – the community in the request must match the setcommu

• GE 1018959, 8.3.2 SSL Certificates HTTPS is not a protocol itself, but it actually refers to HTTP communication over SSL (Secure Sockets Layer) connection. HTTPS uses public-key cryptography to protect the communication. With HTTPS, the server sends back its identification in the form of a digital certificate. The certificate usually contains the server name, the trusted certificate authority (CA), and the server's public encryption key. The server certificate includes a digital signature from a certification authority. Each browser is normally equipped with a set of CA root certificates of commercial authoritie

• GE 1018959, 2.2.9 Trap command group The trap command group allows to configure the trap sending functionality. With SNMP traps various systems can be notified in case of UPS events and alarms. Command Parameters Description showtrap Show detailed trap configuration sendtrap on | off Enable/disable send trap [RFC1628] function on Trap sending enabled off Trap sending disabled sendgetrap on | off Enable/disable send trap [GE-MIB] function on Trap sending enabled off Trap sending disabled NOTE: 3-ph version ONLY addtraptgt [X.X.X.X] v1 | v2 [community] [port] Add a trap address [X.X.X.X] IP-address of the trap target v1 | v2 SN

• GE 1018959, The fingerprint may be checked against the information provided by the SNMP/Web adapter to confirm to SSH server identity. On the console interface inject the ssh-fingerprint command. Below is a sample output of the ssh-fingerprint command: GEDE> ssh-fingerprint 1024 6e:07:31:58:16:91:ae:2e:43:6f:03:64:94:57:55:6d ssh_host_rsa_key.pub 1024 06:97:69:97:cd:93:1b:b6:29:ca:34:e5:8c:35:7c:6e ssh_host_dsa_key.pub 1024 d1:9b:50:13:b3:e3:98:8e:8c:76:49:14:be:21:ed:b3 ssh_host_key.pub The output can be interpreted as follows: Key SSH version Cryptography algorithm ssh_host_rsa_key.pub v2 RSA ssh_host_dsa_key.pub v2 DSA ssh_host_key.pub v1

• GE 1018959, 1.3 ARCHITECTURE ARCHITECTURE DIAGRAM UPS Windows Linux UNIX Ethernet Local console NOTE : only required for configuration UTP 1:1 RS232 10/100 Mbit/s Contact i/f (1-ph plug-in version only) 1.4 SAFETY All maintenance and service work should be performed by qualified service personnel only. Please read carefully the Installation Manual before installing or operating the adapters. For more information on the UPS system, please refer to the applica

• GE 1018959, 7.2.1 Register addressing In a parallel 3-ph UPS system, the various UPS in the system can be addressed by using a particular register address encoding yyXyy, where X represents the UPS ID in the system: 0 - UPS1; 1 - UPS2; 2 - UPS3; 3 - UPS4; 4 - UPS5; 5 - UPS6; 6 - UPS7; 7 - UPS8; 8 - System The System UPS is a virtual UPS that reports alarms, status and measures for the entire UPS system. For stand-alone 3-ph UPS and for 1-ph UPS only one set is available, that is 0 – UPS 1. 7.2.2 Data Types The UPS status and measures are available in different data types. Data types exceeding the 16-bit register len

• GE 1018959, 8.4 CUSTOMER RESPONSIBILITY As shown above, the SNMP/Web adapters implement advanced security features. Nevertheless, achieving complete security protection requires the introduction of a comprehensive security program. This section lists some good practices in network security that customers are recommended to adopt. 8.4.1 Physical security Most of the security features would prove useless if physical access to the equipment is uncontrolled. In fact, physical access is probably the major security hazard for a site. This problem may

More Instructions:

	GE 1018959 Installation manual 27-12-2022 24	DOWNLOAD
	GE 1018959 Operating manual 05-02-2024 58	DOWNLOAD

Related Products and Documents (Computer Accessories):

Comparable Devices:

Similar Resources:

• Connect IT CI-1118 (12 pages) WIRELESS KEYBOARD AND MOUSE SETKABELLOSES SET TASTATUR & MAUSBEZPRZEWODOWY ZESTAW KLAWIATURY I MYSZYBEZDRÁTOVÝ SET KLÁVESNICE A MYŠIBEZDRÔTOVÝ SET KLÁVESNICE A MYŠICI-1118 • CKM-7500-CS • CKM-7510-CSENDEPLCZSKUSER MANUALBENUTZERHANDBUCHPODRĘCZNIK UŻYTKOWNIKAUŽIVATELSKÝ MANUÁLUŽÍVATEĽSKÝ MANUÁLWIRELESS KEYBOARD AND MOUSE SETKABELLOSE …

• NEC N8101-616F (6 pages) 855-910997-616-00 Keep this manual carefully along with the product N8101-616F Xeon Processor Kit User’s Guide The User's Guide is intended to allow you to install and use the Xeon Processor Kit. N8101-616F correctly and safely. Read this manual thoroughly before handling the Kit. In addition, refer to this guide whenever you want to know how t …

• Samsung ES55 (82 pages) This Quick Start Manual has been specially designed to guide you through the basic functions and features of your device. Please read the Quick Start Manual and User Manual carefully to ensure safe and correct use.Quick Start ManualES55For more information, refer to the User Manual included on the supplied CD-ROM.ENG / FRE / TUR / T.CHI / IND / ARA / THA / …

• Lenovo 6019 (506 pages) Machine Types 6019, 6062, 6064, 6065, 6066, 6071, 6072, 6073,6076, 6077, 6078, 6087, 6088, 6089, 9011, 9014, 9071,9089, 9162, 9181, 9182, 9196, 9303, 93256067,ThinkCentreHardware Maintenance Manual …

• Fortinet 5003A (26 pages) FortiSwitch-5003A System GuidePreliminary-01-30000-77803-20080917FortiSwitch-5003ASystem GuideA detailed guide to the FortiSwitch-5003A system. This FortiSwitch-5003A System Guide describes the FortiSwitch-5003A hardware features, how to install the FortiSwitch-5003A board in a FortiGate-5000 series chassis, and how to configure the FortiSwitch-5003A system. …

• NetComm Powerline series (2 pages) 1. Connect one end of the supplied Ethernet cable into a LAN Ethernet port of your modem/router. Connect the other end of the cable into one of your Powerline Adapters.2. Connect the Powerline Adapter to a wall power socket 3. Connect one end of the other supplied Ethernet cable into an Ethernet port of the device you want to connect to the Internet ( …

Comments, Questions and Opinions: