Manualios.com

Sharp CD-BA300 Operation Manual

Sharp CD-BA300 Manual Online:

4, 2438 votes
Sharp CD-BA300 User Manual
Sharp CD-BA300 User Guide
Sharp CD-BA300 Online Manual

Text of Sharp CD-BA300 User Guide:

  • Sharp CD-BA300, 3 CAUTION All the safety and operating instructions should be read before the appliance is operated, and should be retained for future reference. Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. Improper use can result in potential electrical shock or fire hazards. In order not to defeat the safeguards, observe the following basic rules for its installation, use and servicing. 1 Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. 2 Fo

  • Sharp CD-BA300, 10 System Connections FM antenna Right speaker Left speaker AM loop antenna AC outlet (AC 120 V, 60 Hz) VCR, DVD, etc. Preparation for Use – System Connections – not supplied *BA300_P10_12 00.11.16, 2:48 PM10

  • 15 To confirm the time display: Press the CLOCK button. The time display will appear for about 5 seconds. Note: The “CLOCK” or time will flash at the push of the CLOCK button when the AC power supply is restored after a power failure or after unplugging the unit. Readjust the clock as follows. To readjust the clock: Perform “Setting the Clock” from the beginning. If the

  • Sharp CD-BA300, 16 Listening to a CD (CDs) 1 Press the ON/STAND-BY button to turn the power on. 2 Press the CD button. 3 Press the 7 7 7 7 7 OPEN/CLOSE button to open the disc tray. 4 Place the CD(s) on the disc tray, label side up. When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. ● CDs can be placed on any open position on the disc tray. ● Be sure to place 3" (8 cm) CD(s) in the middle of the disc positions. 5 Press the 77 77 7 OPEN/CLOSE button to close the disc tray. The music schedule will display only

  • Sharp CD-BA300, 25 You can record from TAPE 1 to TAPE 2. For recording use only normal tape. Do not use metal and CrO2 tapes. 1 Press the ON/STAND-BY button to turn the power on. 2 Load a prerecorded cassette into the TAPE 1 cassette compart- ment. Insert a blank tape into the TAPE 2 cassette compartment. It is recommended that the recording tape be the same length as the master tape. 3 Press the TAPE (1 VV VV V 2) button until “TAPE 1” appears in the display. 4 Press the REC PAUSE I6 I6 I6 I6 I6 ( I6I6 I6

  • Sharp CD-BA300, 17 7 Press the 0/R 0/R 0/R 0/R 0/R ( 0 R0 R 0 R0 R 0 R) button to start playback. ● Playback will begin from track 1 on the disc you have selected to play. After that disc finishes playing, the next disc will automatically play. ● When the last track on the third disc has finished playing, the CD player will stop automatically. ● When there is no CD in one of the disc 1 - 3 positions, that position will be skipped and the next CD will be played. To interrupt playback: Press the CD 6 button on the remote control. To resume playback from the same point, press the 0 R button. To stop playb

  • 8 Controls and Indicators (continued) ■ Remote control Reference page 01. Remote Control Transmitter .............................................................. 12 02. Disc Number Select Buttons .................................................16, 19, 24 03. CD Pause Button ............................................................................. 17 04. CD Memory Button.

  • Sharp CD-BA300, 20 Listening to the Radio 1 Press the ON/STAND-BY button to turn the power on. 2 Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). 3 Press the TUNING/TIME ( XX XX X or WW WW W) button to tune in to the desired station. Manual tuning: Press the TUNING/TIME button as many times as required to tune in to the desired station. Auto tuning: When the TUNING/TIME button is pressed for more than 0.5 seconds, scan- ning will start automatically and the tuner will stop at the first receivable broad- cast station. Notes: ● When radio interference occurs, auto scan tuning may stop automatically at that point. ● Auto scan tuning will skip weak signa

  • Sharp CD-BA300, 18 ■ Repeat Play All tracks on up to 3 discs, or a programmed sequence can be continuously repeated. To repeat all tracks on up to 3 discs: Press the 0/R (0 R) button twice. To repeat a desired track: Perform steps 1 - 4 in the “Programmed Play” section and then press the 0/R (0 R) button twice. To cancel repeat play: Press the 0/R (0 R) button again. “R” will go out. Repeat or Random Play Starting playback with a desired track ■ Random Play The tracks on the disc(s) can be played in random order automatically. Press the RANDOM button on the remote control to begin random play. To cancel random play: Press

  • Sharp CD-BA300, 6 Controls and Indicators ■ Front panel Reference page 01. Disc Tray........................................................................................... 16 02. Timer Set Indicator.......................................................................... 27 03. Power On/Stand-by Button ................................................13, 26, 30 04. Tape 2 Cassette Compartment ................................................. 22, 25 05. Tape 1 Cassette Compartment ................................................. 22, 25 06. Equalizer Mode Select Button ........................................................14 07. Volume Control............

  • Sharp CD-BA300, Printed in Malaysia B0012.HK CD-BA300 Mini Component System TINSE0337AWZZ SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 SHARP CORPORATION 9906 CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original con- tainer, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does

  • Sharp CD-BA300, 30 ■ If trouble occurs When this product is subjected to strong external interference (mechanical shock, ex- cessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is oper- ated incorrectly, it may malfunction. If such a problem occurs, do the following: 1. Set the unit to the stand-by mode and turn the power on again. 2. If the unit is not restored in step 1, unplug and plug in the unit, and then turn the power on. 3. If neither step 1 nor 2 does not restore the unit, do the following: ¡ Press the ON/STAND-BY button to enter the power stand-by mode. �

  • Sharp CD-BA300, 9 ■ Speaker system Speaker grilles are removable: Make sure nothing comes into contact with the speaker diaphragms when you remove the speaker grilles. Placing the speaker system: The left and right speakers have individual shapes. For best performance, place the speakers according to the illustration on the right. Bi-amp system: Each speaker unit has a built-in subwoofer (low frequency range) which is driven separately from the woofer and tweeter (mid-to-high frequency range). Two indepen- dent amplifiers which have individual frequency characteristics are used. By amplifying separately the tw

  • Sharp CD-BA300, 11 Connections (continued) ■ FM/AM loop antenna connection Connect the FM/AM loop antenna to the ANTENNA jack. ■ Connecting the AC power cord After checking all the connections have been made correctly, plug the AC power cord of this unit into the AC outlet. If you plug in the unit first, the unit will enter the demonstration mode (see page 13). Note: Unplug the unit if it will not be used for a prolonged period of time. ■ Speaker connection Main terminals: Connect the lower black wire to MAIN(-) terminal and the blue wire to the MAIN(+) terminal. Subwoofer terminals: Connect the upper black wire to the SUBWOOFER(-) terminal and the red wire

  • Sharp CD-BA300, 28 The connection cable is not included. Purchase a commercially available cable as shown below. Enhancing Your System To the line output jack Red White RCA cord (not supplied) VCR, DVD, etc. ■ Listening to the playback sounds from VCR, DVD, etc. 1 Use a connection cable to connect the VCR, DVD, etc. to the VIDEO/ AUX jacks. When using video equipment, connect the audio output to this unit and the video output to a television. 2 Press the ON/STAND-BY button to turn the power on. 3 Press the VIDEO/AUX button. 4 Play the connected equipment. Note: To prevent hum interference, place this unit away fr

  • 22 Listening to a Cassette Tape (TAPE 1 or TAPE 2) 1 Press the ON/STAND-BY button to turn the power on. 2 Open the cassette door by pushing the area marked “ 7 7 7 7 7 PUSH EJECT”. 3 Load the cassette into the TAPE 1 or TAPE 2 cassette compartment with the side to be played facing toward you. 4 Press the TAPE (1 VV VV V 2) button to select the cassette you want to listen to. 5 Press

  • Sharp CD-BA300, 23 Tape Recording – Recording from the Radio – 1 Tune in to the desired station. (See page 20.) 2 Load a cassette into the TAPE 2 cassette compartment with the side to be recorded on facing you. Wind past the leader of the tape, on which recording cannot be performed. 3 Press the REC PAUSE I6 I6 I6 I6 I6 ( I6I6 I6I6 I6) button. Recording will be paused. 4 Press the 0/R0/R 0/R0/R 0/R button on the main unit or the TAPE 2 0 0 0 0 0 button on the remote control to start recording. To interrupt recording: Press the REC PAUSE I6 (I6) button. To resume recording, press 0/R (TAPE 2 0) b

  • Sharp CD-BA300, 5 Precautions ■ General ● Please ensure that the equipment is positioned in a well ventilated area and ensure that there is as least 4" (10 cm) of free space along the sides, top and back of the unit. ● Use the unit on a firm, level surface free from vibration. ● Keep the unit away from direct sunlight, strong magnetic fields, excessive dust, humidity and elec- tronic/electrical equipment (home computers, fac- similes, etc.) which generates electrical noise. ● Do not place anything on top of the unit. ● Do not

  • 13 Brightened Dimmed General Control ■ Demonstration mode The first time the unit is plugged, the unit will enter the demonstration mode. You will see words scroll. To cancel the demonstration mode: When the unit is in the power stand-by mode (demonstration mode), press the X- BASS/DEMO button. The demonstration mode will be canceled and the display will disappear. To return to the demonstra

  • Sharp CD-BA300, 27 6 Press the TUNING/TIME ( W W W W W or XX XX X) button to specify the minute, then press the MEMORY/SET button. 7 The unit will enter the timer stand-by mode automatically. To cancel the timer playback/timer recording: Press the ON/STAND-BY button to turn the power on. 8 When the preset time is reached, playback or recording will start. The volume will increase gradually until it reaches the volume you were listen- ing at before your system enters the timer stand-by mode. 9 In timer playback: If you select CD or TAPE, the unit will enter the stand-by mode after the play- back. If you select TUNER or VIDEO/AUX, it will enter the stand-by mode on

  • Sharp CD-BA300, 19 Programmed Play 1 While in the stop mode, press one of the s s s s s 1 - s s s s s 3 buttons to select the de- sired disc. 2 Press the 55 55 5 3 3 3 3 3 PRESET XX XX X or W W W W W PRESET 2 4 2 4 2 4 2 4 2 4 button to select the desired track. You can also select a track by pressing the 3 / 5 3 / 5 3 / 5 3 / 5 3 / 5 or 2 / 4 2 / 4 2 / 4 2 / 4 2 / 4 button on the remote control. Selected disc number Selected track number 3 Press the MEMORY/SET (MEMORY) button to save the track number. When

  • Sharp CD-BA300, Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. CD-BA300 Mini Component System consisting of CD-BA300 (main unit) and CP-BA300 (speaker system). MINI COMPONENT SYSTEM MODEL CD-BA300 OPERATION MANUAL *BA300_P01 00.11.16, 2:46 PM2

  • Sharp CD-BA300, 29 Troubleshooting Chart Many potential “problems” can be resolved by the owner without calling a service tech- nician. If something is wrong with this product, check the following before calling your authorized SHARP dealer or service center. ■ Cassette deck Symptom ● Cannot record. ● Cannot record tracks with proper sound quality. ● Cannot erase completely. ● Sound skipping. ● Cannot hear treble. ● Sound fluctuation. ● Cannot remove the tape. Possible cause ● Is the erase-protecti

  • Sharp CD-BA300, 31 ■ Tuner Frequency range FM: 87.5-108 MHz AM: 530-1,720 kHz ■ Cassette deck Frequency response 50-14,000 Hz (Normal tape) Signal/noise ratio 55 dB (TAPE 1, playback) 50 dB (TAPE 2, recording/playback) Wow and flutter 0.25 % (WRMS) ■ Speaker Type 3-way type speaker system 2" (5 cm) Tweeter 5-1/4" (13 cm) Woofer 6-1/2" (16 cm) Subwoofer Maximum input power (Total) 250 W Rated input power (Total) 125 W Impedance 6 ohms Dimensions Width: 11-5/16" (287 mm) Height: 13" (330 mm) Depth: 11-1/

Related Products and Documents (Other):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Hotpoint Ariston ARGD 149 User manual manual hotpoint-ariston/argd-149-452.pdf 03 Jan 2024 84
2 Pioneer XV-HTD50 Service manual pioneer/xv-htd50-7S5.pdf 29 Nov 2023 113
3 ASL INTERCOM PS 10 Operation & user’s manual asl-intercom/ps-10-7K5.pdf 20 Dec 2023 3
4 Philips MX965 Specification philips/mx965-73Y.pdf 26 Sep 2023 2 0.35 Mb
5 Polar Electro A360 Getting started manual polar-electro/a360-T3Q.pdf 20 Oct 2023 2
6 Sony DR-EX12iP/BLK Specifications sony/dr-ex12ip-blk-WB6.pdf 25 Sep 2022 2 0.16 Mb

Similar Resources:

  • CABASSE

    SANTORIN 30 I -

    (5 pages)
    SANTORINnotice d’installation des caissons de gravessubwoofers operating instructionssubwoofers gebrauchsanweisung30 iwww.cabasse.comCab notice Sub-03 _v2:Cab notice Sub-03 13/11/09 12:58 Page1 …
  • AMX

    NXC-VOL4

    (2 pages)
    Installation GuideNXC-VOL4 Volume Card, 4 ChannelsNetLinx Control Cards and NetModulesNetLinx Control Cards can be installed in either the NXF CardFrame, NI-4000, or NetModules. This document provides basic specifications and wiring information for the NetLinx Control cards. For detailed information on the cards, refer to the NetLinx CardFrame, Control Cards …
  • LOKAR

    Throttle Pedal Assembly

    (2 pages)
    For Steel and Aluminum Pedals General Installation Notes: Please read these instructions completely before beginning the installation. Before beginning the installation, disconnect the negative battery cable and use wheel chocks to block the vehicle's wheels.Make sure the engine, transmission, body and frame are properly grounded. We recommend applying …
  • Arcam

    A80

    (60 pages)
    A 8 0P 8 0H A N D B O O K / M A N U E L / H A N D B U C H / H A N D L E I D I N GEnglishFrançaisDeutschArcam A80 and P80 ampliersAmplicateurs Arcam A80 et P80Arcam-Verstärker A80 und P80Arcam-versterkers A80 en P80Nederlands …
  • Sennheiser

    MZH 3040

    (2 pages)
    MZH 3015LMZH 3040LThe MZH 3015L and MZH 3040L are sturdy and elegant metal goosenecks with one flexible element for use with the ME 34, ME 35 and ME 36 microphone capsules. The LED light ring indicates an active microphone. The rugged, matte black goosenecks are fitted with a balanced floating XLR-5M connector, enabling the microphone to be powered from 12 - …
  • Weslo

    Aero A8

    (12 pages)
    ATTENTION Lisez toutes les précautions etles instructions contenues dansce manuel avant d’utiliser cetappareil. Gardez ce manuel pourvous y référer ultérieurement.Nº. du Modèle WLEMEX14830Nº. de Série Autocollantdu Numérode SérieQUESTIONS?En tant que fabricant nous nousengageons à satisfaire notreclientèle entièrement. Si vousavez des question …

Comments, Questions and Opinions: