Sharp XG-P560W - WXGA DLP Projector Setup Manual
|
Sharp XG-P560W - WXGA DLP Projector, -45 Video Wall Projection Setting up the Video Wall Projection Basic Following is an example of how to build a 2 X 2 video wall using 4 projectors. Projector 1 Projector 2 Projector 3 Projector 4 COMPUTER/COMPONENT1 terminal RGB cable RGB cable RGB cable RGB cable MONITOR OUT (FOR COMPUTER/ COMPONENT1,2) terminal COMPUTER/COMPONENT1 terminal COMPUTER/COMPONENT1 terminal COMPUTER/COMPONENT1 terminal MONITOR OUT (FOR COMPUTER/ COMPONENT1,2) terminal MONITOR OUT (FOR COMPUTER/ COMPONENT1,2) terminal Computer
Sharp XG-P560W - WXGA DLP Projector, -26 Controlling the Projector via LAN Controlling the Projector Using Internet Explorer (Version 5.0 or later) Complete connections to external equipment before starting the operation. (See pages 24- 27 of the projector’s operation manual.) Complete the AC cord connection. (See page 28 of the projector’s operation manual.) Note • When connecting the projector to the LAN, use a commercially available LAN cable (UTP cable, Category 5, cross-over type). When connecting the projector to a hub, use a straight-through cable. 1 Start Internet Explorer (version 5.0 or later) on the computer. 2 Enter “http://” followed by the projector IP address set by the procedure on page 25 follo
Sharp XG-P560W - WXGA DLP Projector, -2 For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. Note • The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult. • For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtain
Sharp XG-P560W - WXGA DLP Projector, -5 Fixed Wide Lens (AN-P8EX) F2.5, f=11.6 mm 16:10 Signal Input (Normal Mode) The formula for picture size and projection distance [m/cm] L (m) = 0.01744 χ H1 (cm) = – 0.96916 χ H2 (cm) = – 0.37689 χ W (cm) = ±0.23691 χ [Feet/inches] L (ft) = 0.01744 χ / 0.3048 H1 (in) = – 0.96916 χ / 2.54 H2 (in) = – 0.37689 χ / 2.54 W (in) = ±0.23691 χ / 2.54 χ : Picture size (diag.) (in/cm) L: Projection distance (m/ft) H1: Lower distance from the lens center to the bottom of the image (cm/in) H2: Upper distance from the lens center to the bottom of the image (cm/in) W: Distance from the lens center to the
Sharp XG-P560W - WXGA DLP Projector, -56 Troubleshooting \ Ta ke the following steps for checking the network settings for the computer. 1. Open a command prompt. • In the case of Windows ® 2000: click “start” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order. • In the case of Windows ® XP, Windows Vista ® : click “start” ➔ “All Programs” ➔ “Accessories” ➔ “Command Prompt” in order. 2. After launching the command prompt, enter the command “ipconfig”, and press the “Enter” key. Note • Communication may not be established even after carrying out the network settings for the comp
Sharp XG-P560W - WXGA DLP Projector, -39 Controlling the Projector Using RS-232C or Telnet Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) It is possible to confirm that a network connection between the projector and a computer etc. is work- ing normally. 11 11 1 Enter “5” and press the “Enter” key. 22 22 2 Enter IP address of device to be tested and press the “Enter” key. Display entered IP address (*1). Display test result (*2). Note • If the “Enter” key is pressed without entering an IP address, the Ping Test IP address used previ- ously is entered. • If there is a fault with the connection, “Error: No answer” is displ
Sharp XG-P560W - WXGA DLP Projector, -14 Computer control A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, commercially available) to the projector. (See page 27 of the projector’s operation manual for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit Data length: 8 bits Flow control: None *Set the projector’s baud rate to the same rate as used by the computer. Basic format Commands from the computer are sent in the following order: command, paramete
-34 Controlling the Projector Using RS-232C or Telnet View Setting Detail List ([V]View All Setting) 11 11 1 Enter “v” and press the “Enter” key. Display all setting values(*). Enter number or symbol of item to be selected on the SETUP MENU. When setting, input the details to be set. Setting is carried out one item at a time, and saved at the end. ▼S
Sharp XG-P560W - WXGA DLP Projector, -16 CONTROL CONTENTS Power ON Standby mode (or 40-second startup time) COMMAND PARAMETER RETURN OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ER
Sharp XG-P560W - WXGA DLP Projector, -32 Setting the Projector Using RS-232C or Telnet When Connecting Using Telnet 1 Click “start” from the Windows ® desk- top and select “Run”. 2 Enter “telnet 192.168.150.2” in the text box that opens up. (If the IP address of the projector is 192.168.150.2.) 3 Click the “OK” button. 4 “User Name:” is displayed. Input the user name and press the “Enter” key. • If a user name has not yet been set, just press the “Enter” key. 5 “Password:” is displayed. Input the password a
Sharp XG-P560W - WXGA DLP Projector, -18 CONTROL CONTENTS Power ON Standby mode (or 40-second startup time) COMMAND PARAMETER RETURN OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK
Sharp XG-P560W - WXGA DLP Projector, -36 Controlling the Projector Using RS-232C or Telnet IP Address Setting ([1]IP Address) Setting of IP address. 11 11 1 Enter “1” and press the “Enter” key. 22 22 2 Enter numerical value to be set and press the “Enter” key. Display IP address after change (*). Subnet Mask Setting ([2]Subnet Mask) Setting subnet mask. 11 11 1 Enter “2” and press the “Enter” key. 22 22 2 Enter numerical value to be set and press the “Enter” key. Display subnet mask after change (*). The setting procedure for e
Sharp XG-P560W - WXGA DLP Projector, -53 1 Click “Start” – “All Programs” – “Accessories” – “Communica- tions” – “HyperTerminal”. • If you do not have HyperTerminal in- stalled, see the operation manual of your computer. • Depending on the settings of your com- puter, you may be required to enter your area code and other details. Enter the information as required. 2 Enter a name in the “Name” field, and click “OK”. 3 If you are required to enter the area code, enter it in the “Area code” field. From the “C
Sharp XG-P560W - WXGA DLP Projector, -37 Controlling the Projector Using RS-232C or Telnet Password Setting ([5]Password) Carrying out security protection using password. 11 11 1 Enter “5” and press the “Enter” key. 22 22 2 Enter password and press the “Enter” key. Display set password (*). Note • Password can be up to 8 characters. • You can input the characters below : a-z, A-Z, 0-9, -, _ • In the default state, the password is not set. RS-232C Baud Rate Set- ting ([6]RS-232C Baud Rate) Setting of baud rate for RS-232C (COMPUTER and PROJECTOR) terminals. 11 11 1 Enter “6” and press the “Enter” key. 22 22 2 Select and enter the number 0, 1 or 2 and press the “Enter” ke
-38 Controlling the Projector Using RS-232C or Telnet Disconnecting All Connec- tions ([D]Disconnect All) It is possible to disconnect all the TCP/IP connec- tions currently recognized by the projector. Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force the Ready status back by carrying out this disconnection.
Sharp XG-P560W - WXGA DLP Projector, -27 Confirming the Projector Status (Status) On this screen, you can confirm the projector status. You can confirm the following items : •• •• • MAC Address •• •• • Power •• •• • Condition •• •• • Lamp Timer 1 •• •• • Lamp Timer 2 •• •• • Lamp Life 1 •• •• • Lamp Life 2 •• •• • Input •• •• • Signal Info •• •• • Serial Number Note • If you click the “Refresh” button before the screen is displayed completely, an error message (“Server Busy Error”) will be dis- played. Wait for a moment an
Sharp XG-P560W - WXGA DLP Projector, -44 Video Wall Projection Info • Before setting up the video wall projection, install Internet Explorer (version 5.0 or later). • Video wall is not compatible with resolutions higher than SXGA. • Image quality may deteriorate when picture signals are input through multiple projectors with an RGB cable or an RCA cable in a daisy chain connection. Usually, a costly image-processing device is required to set up a video wall projection. This projector has built-in video wall capability that doesn’t require additional equipment.
-6 Fixed Wide Lens (AN-P12EX) F2.5, f=17.1 mm 16:10 Signal Input (Normal Mode) The formula for picture size and projection distance [m/cm] L (m) = 0.02619 χ H1 (cm) = – 0.96916 χ H2 (cm) = – 0.37689 χ W (cm) = ±0.23691 χ [Feet/inches] L (ft) = 0.02619 χ / 0.3048 H1 (in) = – 0.96916 χ / 2.54 H2 (in) = – 0.37689 χ / 2.54 W (in) = ±0.23691 χ / 2.5
-10 Tele-zoom Lens (AN-P45EZ) F2.5, f=62.1-97.8 mm Note • Allow a margin of error in the value in the diagrams above. • When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates that the bottom of the image is below the lens center. 16:10 Signal Input (Normal Mode) The formula for picture size and projection distance [m/cm] L1 (m) = 0.09821
Sharp XG-P560W - WXGA DLP Projector, -28 Controlling the Projector via LAN Setting and Adjusting the Projector (Settings & Adjustments) Example: “Picture” screen display for COMPUTER1 On these screens, you can make projector settings or adjustments. You can set or adjust the following items : Setting the Security (Network – Security) On this screen, you can make settings relat- ing to security. After clicking the “ Apply ” button, the set val- ues appear. Confirm that the values are set properly, and then click the “ Confirm ” button. Note • After setting items, wait for 10 seconds and then re-access. • User Name and Password can be up to
Sharp XG-P560W - WXGA DLP Projector, -13 Specifications of wired remote control input •• •• • ø3.5 mm minijack •• •• • External: GND •• •• • Internal: +3.3V Function and transmission codes Wired Remote Control Terminal Specifications C1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 C2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 C3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 C4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 C5 C6 0 0 0 1 0 1 0 1 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 1 0 0 0 1 0 1 0 0 0 C7 1 1 0 0 1 1 1 0 1 1 0 1 1 1 0 1 1 C8 0 0 1 1 0 0 1 1 0
Sharp XG-P560W - WXGA DLP Projector, -7 Wide-zoom Lens (AN-P15EZ) F2.5, f=21.2-25.8 mm 16:10 Signal Input (Normal Mode) The formula for picture size and projection distance [m/cm] L1 (m) = 0.03274 χ L2 (m) = 0.0392 χ H1 (cm) = – 1.56815 χ H2 (cm) = 0.2221 χ W (cm) = ±0.75379 χ [Feet/inches] L1 (ft) = 0.03274 χ / 0.3048 L2 (ft) = 0.0392 χ / 0.3048 H1 (in) = – 1.56815 χ / 2.54 H2 (in) = 0.2221 χ / 2.54 W (in) = ±0.75379 χ / 2.54 χ : Picture size (diag.) (in/cm) L1: Minimum projection distance (m/ft) L2: Maximum projection distance (m/ft) H1: Lower distance from the lens center to the bottom of the image (cm/in) H2: Upper distance from the lens center to the bottom of the image (cm/in)
Sharp XG-P560W - WXGA DLP Projector, -12 Connecting Pin Assignments RS-232C Terminal: D-sub 9 pin male connector Pin No. Signal Name I/O Reference 1 Not connected 2RDReceive Data Input Connected to internal circuit 3SDSend Data Output Connected to internal circuit 4 Not connected 5SGSignal Ground Connected to internal circuit 6 Not connected 7RSRequest to Send Connected to CS in internal circuit 8CSClear to Send Connected to RS in internal circuit 9 Not connected RS-232C Cable recommended connection: D-sub 9-pin female connector Pin No. Signal Pin No. Signal 1CD 1 CD 2RD 2 RD 3SD 3 SD 4ER 4 ER 5SG 5 SG 6DR 6 DR 7RS 7 RS 8CS 8 CS 9CI 9 CI Note • Depending on the controlling device used, i
Sharp XG-P560W - WXGA DLP Projector, -24 Setting up the Projector Network Environment 3. Setting up a Network Connection for the Projector Settings for such items as the projector’s IP address and subnet mask are compatible with the existing network. Set each item on the projector as follows. (See page 64 of the projector’s operation manual for setting.) DHCP Client : OFF IP Address : 192.168.150.002 Subnet Mask : 255.255.255.000 1 Start Internet Explorer (version 5.0 or later) on the computer, and enter “http://192.168.150.2/” in “Address”, and then press the “Enter” key. 2 If a user
Sharp XG-C435X-L Projector Operation manual
XG-C435X-L |
Sharp AN-C41MZ Projector Installation manual
AN-C41MZ |
Sharp Conference Series XG-PH80W-N Projector Operation manual
Conference Series XG-PH80W-N |
Sharp XG-C335X - Notevision XGA LCD Projector Projector Specification sheet
XG-C335X - Notevision XGA LCD Projector |
Sharp AN-PH10EX Projector Operation manual
AN-PH10EX |
Sharp XG-3850E Projector Operation manual
XG-3850E |
Sharp PG-D2510X Projector Specification sheet
PG-D2510X |
Sharp Notevision XG-C465X Projector Operation manual
Notevision XG-C465X |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Asus | EEE PAD ME171 | Operation & user’s manual | asus/eee-pad-me171-1E1.pdf | 26 Nov 2023 | 26 | 2.41 Mb |
2 | Sole Fitness | Treadmill | Owner's manual | sole-fitness/treadmill-CQ6.pdf | 13 Dec 2023 | 34 | |
3 | Philips | AJ1000B | Specifications | philips/aj1000b-DP4.pdf | 26 Jan 2024 | 3 | 1.37 Mb |
4 | Gembird | CHM-02 | Operation & user’s manual | gembird/chm-02-BF6.pdf | 28 Jun 2023 | 38 | 1.1 Mb |
5 | LG | ARNU24GSCL2 | Owner's manual | lg/arnu24gscl2-28I.pdf | 15 Feb 2024 | 109 | |
6 | Xerox | WorkCentre 7132 | Setup manual | xerox/workcentre-7132-9M2.pdf | 07 Aug 2023 | 10 | 0.08 Mb |
Sanyo
Multimedia ProjectorSERVICE MANUALPRODUCT CODE 1 122 340 20 (KE6AL)1 122 341 20 (LE6AL)1 122 341 22 (LE6CL)Original VersionREFERENCE NO. SM5110792-00FILE NO.Model No. PLC-XP57LU.S.A., Canada, Europe, Asia, Africa,(Projection lens is optional.)Chassis No. KE6-XP57L00NOTE: Match the Chassis No. on the unit’sback cover with the Chassis No. in theService Manua …
PLC-XP57L(122 pages) |
Epson
EPSON EMP-505 SpecificationsModel EMP-505Projection SystemRGB Liquid Crystal Shutter ProjectionSystemProjection Method Front / Rear / Ceiling MountSpecification of Main PartsLCD Size Driving Method Pixel Number Native Resolution Aspect Ratio Pixel ArrangementProjection Lens Type F-number Focal Length Zoom Ratio Len …
EMP-505(3 pages) |
Sony
LSPX-W14-535-453-11(1)L:\Atsugi\HPJ\4535453111\4535453111LSPXW1SY\100BCO.fmmasterpage:Ba ckCover© 2014 Sony CorporationPrinted in JapanOperating InstructionsBefore operating the unit, please read this manual thoroughly and retain it for future reference.LSPX-W1LSPX-W14-535-453-11(2)L:\Atsugi\HPJ\4535453112\4535453112LSPXW1SY\010COV.fmmasterpage:Ba ckCover4- …
LSPX-W1(91 pages) |
ETC
Adjusting the C-clampThe C-clamp attaches the fixture to the mounting pipe and allows you to adjust theposition of the fixture once it is mounted.1. Tightly fasten the C-clamp to the yoke with the yoke bolt and lock washerprovided.2. Place the C-clamp on mounting pipe, then tighten the pipe bolt to secure it.3. Loosen the C-clamp pan screw and rotate the yok …
Source Four LED Series(4 pages) |
Ricoh
ご使用の前に/USB機能プロジェクター取扱説明書(日本国内用)形名IPSiO PJ X3241N IPSiO PJ WX3231N●このたびはリコープロジェクターをお買い上げいただきまして、まことにありがとうございます。●お求めのリコープロジェクターを正しく使っていただ …
PJ X3241N(206 pages) |
3M
May 2007 • 78-6970-9470-0-D • Copyright © 2007, 3M Company. All Rights Reserved.Operator and Product Safety GuideGuía para el operadorBetriebsanleitungGuide de l’utilisateurⱞ᛭ᱲ⧜ᤛꭲ녯ꯪꕋꯢオペレーターズ ガイドGuida dell’operatoreDigital Media System800 Series
…
DMS800 - Digital Media System 800 XGA DLP Projector(32 pages) |
Whirlpool Dryer BYCD3722W0Dryer Use and care manual (Whirlpool BYCD3722W0) BYCD3722W0, 19 |
Nortel Answering Machine P0857846Answering Machine #ZZA835 P0857846, 187 |
Bernafon Hearing Aid NevaraHearing Aid PDF User manual manual Nevara, 52 |
McIntosh Amplifier mc 50Amplifier PDF Owner's manual mc 50, 23 |
Philips Headphone SBCHN110#P8NF48: SBCHN110 Headphone Instructions for use SBCHN110, 1 |
Cooper Security Transmitter 4601-50PDF User Guide (@33O6A5), Cooper Security 4601-50 Transmitter (Saturday 14-10-2023) 4601-50, 4 |
Bryston Crossover 10BBryston Crossover Owner's manual (File: bryston-10b-crossover-12, Wednesday 22-11-2023) 10B, 12 |
Hitachi Projector CP-SX1350Hitachi CP-SX1350 Guide (Doc Type: Projector Technical user's manual) CP-SX1350, 16 |
Sony Laptop VGN-TZ350N/BPDF User Guide (@JC24TO), Sony VGN-TZ350N/B Laptop (13.10.2023) VGN-TZ350N/B, 2 |
Logitech Headsets G933 Artemis SpectrumG933 Artemis Spectrum (Headsets ePDF User Guide, #AT74U8) G933 Artemis Spectrum, 87 |
Boston Speakers i-DS3 plusSpeakers PDF Owner's manual i-DS3 plus, 9 |
Aztech Modem ADSL USB ModemAztech ADSL USB Modem Manual (Easy start manual), @Z6H688 ADSL USB Modem, 10 |