Manualios.com

Siemens SIPART PS2 6DR50xx Manual 

Siemens SIPART PS2 6DR50xx Manual Online:

3.95, 2672 votes
Siemens SIPART PS2 6DR50xx User Manual
Siemens SIPART PS2 6DR50xx User Guide
Siemens SIPART PS2 6DR50xx Online Manual

Text of Siemens SIPART PS2 6DR50xx User Guide:

  • Siemens SIPART PS2 6DR50xx, Design and Functional Principle 16 SIP ART PS2 Manual A5E00074631--06 spond even when the power supply fails or the electronics are defec- tive. The actuator can also be blocked or driven to its final positions depend- ing on the configuration for example by an external event via a digital input (DI2) on the alarm module. If you require electrically independent limit value messages from the standard controller, you will have to use the SIA module with the slot initiators instead of the alarm module. Communication with the controller is possible via the optional HART interface. To be able to use

  • Preparing for Operation 62 SIP ART PS2 Manual A5E00074631--06 31 32 41 42 51 52 SIA module 6DR4004-8G + + + 1K21 10K <35 V 8.2 V 8.2 V Fault message Limit value A1 Limit value A2 Switching amplifier according to EN 60947-5-6 Figure 3-18 SIA module 6DR4004-8G, not Ex Mechnical limit switch module 31 32 41 42 51 52 Limit switch module 6DR4004-8K + + + 1K21 10K <

  • Siemens SIPART PS2 6DR50xx, Design and Functional Principle 21 SIP ART PS2 Manual A5E00074631--06 up down up down up down up down Safety position after power failure electrical pneumatic Down Down Up Up Down Up Y1 Y1 Y2 Y1 Y1 Y2 Y1 Y1 Y2 Y1 Y1 Y2 Open Closed Closed Closed Open Open Closed Open Last position (before power failure) Actuator type Positioning pressure Connection In part-turn actuators the direction of rotation counterclockwise looking onto the actuating shaft of the valve is usually defined as “Open”. Open Closed up down Open Closed OpenClosed OpenClosed Last position (before power failure) Figure 2-6 Pneumatic connection positioning

  • Siemens SIPART PS2 6DR50xx, Preparing for Operation 46 SIP ART PS2 Manual A5E00074631--06 Assembly of the screw-type gland with plastic hose S Unscrew the sinter bronze silencer from the exhaust air opening on the underside of the housing. S Screw the screw-type gland mentioned above into the exhaust air opening. S Mount the above mentioned plastic hose on the screw-type gland and check the good fit. S Fix the plastic hose with a cable strap to the fitting so that the open- ing faces downwards. S Make sure that the hose has no kinks and the exhaust air can flow out unhind

  • Siemens SIPART PS2 6DR50xx, Design and Functional Principle 19 SIP ART PS2 Manual A5E00074631--06 2.3.3 Pneumatic Connections The pneumatic connections are on the right hand side of the positioner (figure 2-4 and figure 2-5). 1 2 3 4 5 1 Actuating pressure Y1 in single- and double-acting actuators 2 Feedback shaft 3 Supply air P z 4 Actuating pressure Y2 in double-acting actuators 5 Exhaust air output E with silencer on the bottom of the instrument Figure 2-4 Pneumatic connection in normal version 1 2 3 4 5 6 7 1 Restrictor Y2 *) 5 Actuating pressure Y1 2 Restrictor Y1 6 Exhaust air output E 3 Actuating pres

  • Preparing for Operation 69 SIP ART PS2 Manual A5E00074631--06 + 0/4to20mA 6DR5210-Gxxx 6DR5220-Gxxx 6DR5211-Gxxx 2 3 4 5 6 7 8 9 10 A E *) *) Only for three-wire connection + 18 to 30 V U *) HAR Communicator J Hazardous area zone 2 Non-hazardous area Positioner Digital input 1 Figure 3-30 Three-/Four-wire connection, EEx n U H 61 62 61 62 I E I y module 6DR4004-

  • Siemens SIPART PS2 6DR50xx, Information for the Operator 5 SIP ART PS2 Manual A5E00074631--06 Information for the Operator Dear customer, Please read this manual before starting work! It contains important information and data which, when observed, ensure full availability of the equipment and save service costs. This simplifies handling of this control instrument considerably and provides accurate measuring results. You have purchased an instrument which can be installed in various configurations: S SIPART PS2 without Ex-protection in a metal- or plastic housing. S SIPART PS2 with EEx ia/ib-protection in a metal- or plastic hous-

  • Siemens SIPART PS2 6DR50xx, Operation 93 SIP ART PS2 Manual A5E00074631--06 The display of the positioner shows you the current potentiometer setting in the top line and “NOINIT” flashes in the second line. You can move the actuator with the decrement and increment key . In order to adapt the positioner to your actuator , you have to change to the Configuration menu. See also chapter 3.6, page 72 “Commissioning”. Output of alarms and position feedback is possible after successful init- ialization. To go to the Configuration menu, press the operation mode key

  • Siemens SIPART PS2 6DR50xx, Operation 95 SIP ART PS2 Manual A5E00074631--06 See chapter 4.5, page 122 for further information. . NOTE The respective operating mode (MAN or AUT) of the positioner is retai- ned when you switch to the diagnostic display, i.e. in automatic opera- tion the specified setpoint is still used for controlling and in manual operation the position last reached is retained. 4.4 Parameters All the parameters of the positioner are listed in this chapter. Figure 4-6 shows an overview of the parameters. The parameter name is shown once in plain text and once as it ap- pears in the display. The function of the parameter is described br

  • Siemens SIPART PS2 6DR50xx, Operation 118 SIP ART PS2 Manual A5E00074631--06 Monitoring of the upper temperature limit The current temperature in the positioner housing is measured by a sensor on the electronic circuit board. This parameter is for the three-level monitoring of the upper temperature limit. Temperature unit The temperature unit can be switched over by pressing the Greater Than or Smaller Than button between °C and °F. Another way of switching over is the H1.TUNIT parameter for monitoring the lower temperature limit. The selected unit applies to all temperature-related parameters. Threshold 1 First threshold for monitoring the upper temperature limit. The factory setting is 75

  • Siemens SIPART PS2 6DR50xx, Operation 122 SIP ART PS2 Manual A5E00074631--06 4.5 Diagnosis 4.5.1 Diagnostic display To access the diagnostic display in automatic or manual mode, press all three buttons for at least two seconds. This following table gives an overview of the values that can be displayed. The third column contains the term from which the abbreviation is derived, unless it is self-explaining. The structure of the diagnostic display is similar to that in “Configu- ration” mode: the upper line shows the diagnosis value, the lower line shows the number and abbreviation of the displayed value. Use the operating mode button to select the next diagnosis value. By pressing and holding the o

  • Siemens SIPART PS2 6DR50xx, Preparing for Operation 45 SIP ART PS2 Manual A5E00074631--06 Figure 3-5 Favorable and unfavorable installation positions If conditions oblige you to operate the positioner in a unfavorable installation position, you can take additional precautionary measures to prevent penetration by water. . NOTE Never clean the positioner with a high pressure water jet because the IP66 degree of protection is inadequate protection for this. The necessary additional measures to prevent penetration by water depend on the installation position chosen and you may additionally require: S scr

  • Siemens SIPART PS2 6DR50xx, Technical Data 149 SIP ART PS2 Manual A5E00074631--06 ■ Technical specifications SIPART PS2 Basic device without Ex protection Basic device with EEx-d protection (flameproof casing) Basic device with EEx ia/ib protection Basic device with EEx n protection Explosion protection to EN 50014, EN 50020 and EN 50021 Without EEx d II 2 G EEx d II C T6 EEx ia/ib II 2 G EEx ia/ib II C T6 EEx n II 3 G EEx nA L [L] II C T6 Mounting location Zone 1 Zone 1 Zone 2 Permissible ambient temperature for operation At ≤ -10 °C (+14 °F) the dis

  • Preparing for Operation 64 SIP ART PS2 Manual A5E00074631--06 + 18 to 30 V 6DR5210-xExxx 6DR5220-xExxx 6DR5211-xExxx 2 3 4 5 6 7 8 9 10 A E U *) Only for three-wire connection J 4to20mA EEx EEx + *) *) HART Communicator Hazardous area zone 1 or zone 2 Non-hazardous area Intrinsically safe power source Positioner Digital input 1 Figure 3-22 Three-/four-wire connection, EEx

  • Siemens SIPART PS2 6DR50xx, Information for the Operator SIP ART PS2 Manual A5E00074631--06 10 0.7 Delivery Notes The scope of delivery is listed on the dispatch papers accompanying the delivery in accordance with the valid contract of sale. When you open the packaging please observe the information on the packaging. Check that the delivery is complete and undamaged. If possible, compare the order number on the rating plates with the or- dering data. For the scope of delivery please see Chapter 7, page 153. 0.8 Standards and Regulations As far as

  • Design and Functional Principle 34 SIP ART PS2 Manual A5E00074631--06 9. Make all the electrical connections between the motherboard and the options with the ribbon cables provided and between the mo- therboard and potentiometers with the potentiometer cable. 10. Fix the enclosed module cover instead of the standard version with the two screws (1.1). 11. Select the plates which already exist on th

  • Siemens SIPART PS2 6DR50xx, Design and Functional Principle 27 SIP ART PS2 Manual A5E00074631--06 2.7 Installation of options modules 2.7.1 Instal la tion of opti ons module s in normal and intrinsi ca ll y safe versions The following option modules are available for the positioner in the standard and the intrinsically safe version: -- l y -module -- Alarm module -- SIA-module -- Mechanical limit switch module -- EMC filter module The installation of the options modules is described below: The option modules are secured by a asse

  • Siemens SIPART PS2 6DR50xx, Operation 98 SIP ART PS2 Manual A5E00074631--06 Normally adjustment of the first three following parameters is com- pletely sufficient to enable a positioner to be operated by an actuator. If you wish to become familiar with all details of the positioner, try out incrementally the effects of the remaining parameters by selective trials. . NOTE In particular if the positioner has previously been operated using a different actuator, it must always be reinitialized in order to restore the factory settings. Only in this way can the positioner matching process start from known conditions. The parameter “55.PRST” is provided for this purpose. This is also recommended if multiple paramet

  • Siemens SIPART PS2 6DR50xx, Care and Maintenance 145 SIP ART PS2 Manual A5E00074631--06 Service and Maintenance The positioner is largely maintenance-free. The positioners are fitted with filters in the pneumatic connections as protection against coarse particles of dirt. If the pneumatic energy supply contains particles of dirt, the filters may clog and impair the function of the positioner. In this case the filters can be cleaned as follows. Positioner in metal housing and explosion proof version 1. Switch off the pneumatic power supply and remove the pipes. 2. Remove the metal filters carefully from the holes and cl

Related Products and Documents (Automobile Parts):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Philips SWV2226 Specifications philips/swv2226-8I9.pdf 19 Nov 2022 2
2 Maytag MGD5700TQ Use and care manual maytag/mgd5700tq-WI1.pdf 19 Aug 2023 64
3 Sony MDR MDR 710LP Operating instructions sony/mdr-mdr-710lp-JB7.pdf 27 Dec 2022 2 0.13 Mb
4 NEC LT180 - LT 180 XGA DLP Projector Installation manual nec/lt180-lt-180-xga-dlp-projector-4J5.pdf 27 Nov 2023 7
5 ShelterLogic 26775 Assembly instructions manual shelterlogic/26775-M7J.pdf 16 Oct 2022 6
6 Eizo FC-2090C Specification eizo/fc-2090c-1B3.pdf 02 Nov 2022 2 0.24 Mb

Similar Resources:

  • Edelbrock

    66722

    (2 pages)
    Catalog #66722, 66723©2008 Edelbrock CorporationPage 1 of 2Brochure #63-66722Rev. 3/08 - AJ/mcTUBULAR EXHAUST SYSTEMFor 1998-1999 Chevrolet/Pontiac, Camaro/Firebird; Z-28,T/A, & Formula, 5.7L LS1 V8 (Dual Catalytic Converters)Catalog #66722, #66723INSTALLATION INSTRUCTIONSPlease study these instructions carefully before installing your new Tubular Exhau …
  • Kohler

    Command PRO CH750

    (88 pages)
    CH18-CH25, CH620-CH730, CH740, CH750Service Manual2 Safety3 Maintenance5 Specifi cations14 Tools and Aids17 Troubleshooting21 Air Cleaner/Intake22 Fuel System28 Governor System30 Lubrication System32 Electrical System48 Starter System57 Clutch59 Disassembly/Inspection and Service72 ReassemblyIMPORTANT: Read all safety precautions and instructions carefully …
  • Dakota Digital

    MCL-2002

    (12 pages)
    MAN# 650280:D MODEL MCL-2002 TANK MOUNT SPEEDOMETER/TACHOMETER *To avoid damage to motorcycle, please see Speedometer, Tachometer, and Status and Warning Indicators sections for details on locating VSS, Tachometer, and indicator wires for most motorcycle applications **For 2004+ HD utilizing the “Fat Bob” tank mount, please see our MCL-2004, it i …
  • Edelbrock

    47522

    (2 pages)
    ©2003 Edelbrock CorporationCatalog #47522Page 1 of 2Rev. 9/03Edelbrock One-Piece Pro-Flo HeaderFor 1994-1999 Acura Integra GS-RCatalog #47522INSTALLATION INSTRUCTIONSPlease study these instructions carefully before installing your new Pro-Flo Header. They provide general guidelines tobe studied and understood before you remove your stock system. Failure …
  • ATD Tools

    TURBO 350

    (2 pages)
    ATD 32248 / Page 1 of 2W140N10145 Fond Du Lac Ave.Germantown, WI 53022Phone: (262) 251-7777Email: [email protected] TURBO 350 FORWARD MANUAL (P/N: 32248)CAUTIONPlease read all of these instructions before proceeding with installation.is or any valvebody should only be installed by a qualied race transmission technic …
  • Edelbrock

    66042

    (2 pages)
    Catalog #66042 & #66043©2006 Edelbrock CorporationPage 1 of 2Brochure #63-66042Rev. 5/06 - DA/mc••PLEASE study these instructions carefully before installing your new Tubular Exhaust System (TES). If you have any questions, please contact ourTechnical Hotline at : 1-800-416-8628 from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at …

Comments, Questions and Opinions: