GE Monogram ZDI15 Installation Instructions Manual

Text of GE Monogram ZDI15 User Guide:

• GE Monogram ZDI15, Installation instructions • BEFORE YOU BEGIN: Read these instructions completely and carefuJJy. • iMPORTANT: Save these instructions for local inspector's use. • iMPORTANT: Observe all governing codes and ordinances. Note to Installer - Be sure to leave these instructions with the Consumer. • Note to Consumer - Keep these instructions with your Owner's Manual for future reference. WARNING: This appliance must be properly grounded. Failure to do so can result in death, fire, or electrical shock. See "Power Supply

• GE Monogram ZDI15, Design information MODELS AVAILABLE ZDI15, ZDIS15 The icemaker may be installed below a countertop or Available in black, white and stainless steel, used free-standing. CUTOUT & PRODUCT DiMENSiONS "16-1/2" with a 3/4" thick custom panel 34" min. Adjustable to 34-1/2" Cutout dimensions shown allow for a full door swing. Additional Clearances: • The installation of a 3/4"thick custom panel will require an additional 1-1/2"wide filler strip on the hinge side. The filler strip will act as a spacer between the icemaker case and an adjacent cabinet. The filler strip will prevent interference with the icemaker door swing when it is i

• Installation instructions ADVANCE PLANNING CAUTION: Duetoexcessive weight, TWO PEOPLEARE REQUIRED TO MOVE AND iNSTALL THiS ICEMAKER. Failure to do so can result in back or other injury. IVliSE EN GARDE : A cause de son poids eleve;JL FAUT DEUX PERSONNES POUR DEPLACER ET iNSTALLER CETTEMACHINE _, OLA_0NS. Le non-respect de ces instructions peut causer des biessures au do

• GE Monogram ZDI15, Installation instructions POWER SUPPLY WARNING: (Please read carefully). FORPERSONAL SAFETY,THIS APPLIANCE MUST BE PROPERLYGROUNDED. Failure to follow these instructions can result in death, fire, or electrical shock. AVERTISSEMENT : (S'ilvous lisez avec soin).POURVOTRE SI_CURITI_,CETAPPAREIL DOlT f:TRE CORRECTEMENTMIS A LA TERRE.Le non-respect de ces instructions peut causer la mort, un incendie ou un choc electrique. Do not use an extension cord or adapter plug with this appliance. Follow National Electrical Code or prevailing local codes and ordinances.

• GE Monogram ZDI15, InstalJation instructions WATER SUPPLY * A cold water supply is required for icemaker operation. The water pressure must be between 30 and 120p.s.i. Water SupplyShould Enter FromBack Wall In ShadedArea. * Route GE SmartConnect TM Kit or 1/4" O.D. copper tubing between house cold water line and the water connection location. The water line should be long enough to extend to the back of the icemaker. Allow enough to accommodate moving unit forward for service. NOTE: The only GEapproved plastic tubing is supplied

• GE Monogram ZDI15, Installation instructions CONNECT WATER SUPPLY * The water line should be flushed to clear any foreign material before connecting to the icemaker. * Connect the water line to the water supply tube outside of the rear access cover. Water @Supply // I Line o Copper Tubing: * Use a standard plumbing female connector or union for 1/4" copper tubing that can be purchased locally. Coupling (NotS@plied) Nut (Supplied) \ Lineto Icemal(er Ferrule (NotSupplied) \ Nut (Supplied) GE SmartConnect'=Tubing: * Insert the molded end of the tubing intothe icemaker connection. Tighten the compression nut until it is j

• GE Monogram ZDI15, Installation instructions REVERSE THE DOOR SWING (cont.} Reverse the hinges: • Using a flat putty knife, remove the screw hole plugs opposite the door hinges, top and bottom. Set aside. • Remove the two screws holding top hinge. • Turn the hinge upside down, with the hinge pin pointing up. Reinstall the hinge on the opposite side at the bottom of the door. Remove the bottom hinge. Turn the hinge upside down and install on the opposite side atthe top. • Push screw hole plug buttons (supplied) into the original screw holes. Remove the top hinge pin. Place plastic hinge sleeve on the bottom hinge and position the door onto the pin. • Place plastic hinge sleeve in

• GE Monogram ZDI15, Installation instructions for ZIP75WW, ZIP75BB Kit • BEFORE YOU BEGIN: Read these instructions completely and carefuJJy. • iMPORTANT: Save these instructions for local inspector's use. • iMPORTANT: Observe all governing codes and ordinances. • Note to Instafler- Be sure to leave these instructions with the Consumer. • Note to Consumer - Keep these instructions with your Owner's Manual for future reference. WARNING: Disconnect electrical power supply to icemaker before installing front panel. Do not operate icemaker while installing p

• GE Monogram ZDI15, Installation instructions for ZIP75WW, ZIP75BB Kit TO THE iCE MACHINE STEP 2 REMOVE HANDLE AND NAMEPLATE • Remove the door handle by removing the two top mounting screws. Set screws aside, Discard handle. • The Monogram nameplate is held in place with adhesive. Remove the nameplate. STEP 3 MARK MOUNTING SCREW LOCATIONS • Align and hold the side trim pieces against the icemaker door and mark screw locations on the sides. • Drill 1/8" pilot holes into the door sides of the icemaker. STEP 4 SECURE CUSTOM HANDLE TO CUSTOM PANEL. (SKIP THIS STEP IF YOU ARE USING THE SUPPLIED HANDLE) A

• GE Monogram ZDI15, Pub.No.49-60016-4 ] ] PartNo.197D2522PO01 2217409 02-06JR Printedin tl_eUnitedStates NOTE:While performing installations described in this book, safety glasses or goggles should be worn. o oo ]l))F ,_lO?tO_'Yaltt [0(:(1[ ,_(_-Uit:( _ i?t 30_tT (/?'('(/, c(l[I l ._00. 444. l,_4 _. ) NOTE: I vodu(:l inll)rov(*nlenl is a continuing endeavor al ( enel-al Ele(lri(. Thel-et_n-e, malel-ials, al)l)earal_(e and Sl)e(ifi(aliol_S _11(_ stl|)i(..1 lo (hange wilhoul noli(e. Monogram: GECol_sumer& Industria / GEAppliancos Gotle_] Electric _mpang Louisdlle, KY40225 go com ©2000 GE Compmly

More Instructions:

	GE Monogram ZDI15 Installation instructions manual 20-09-2023 12	DOWNLOAD
	GE Monogram ZDI15 Owner's manual 01-08-2022 16	DOWNLOAD
	GE Monogram ZDI15 Owner's manual 21-07-2022 16	DOWNLOAD
	GE Monogram ZDI15 Installation instructions manual 16-06-2023 12	DOWNLOAD

Related Products and Documents (Ice Maker):

Comparable Devices:

Similar Resources:

• Whirlpool CHCH8AE (8 pages) IMPORTANT INSTALLATION INSTRUCTIONS for MALFUNCTION LIGHT. “ON-OFF-CLEAN” SWITCH BEHIND NAMEPLATE Whirlpoo CORPORATII Electrical Supply 115208/230 V. 3-Wire 60 Hz-l Ph. NOTICE: ICE STORAGE BIN SUPPLIED SEPARATELY. It is essential that a suitable ice storage bin of durable construction be used with the ice cube maker and that th …

• Ice-O-Matic EMF 2306 (2 pages) ®EMF 2306 SeriesFlake ICE MakerEMF 2306 on a B100 BinICE-O-Matic®is the Best ICE Making Solution for: Hard Water, Food Safety and Tight Spaces✓ Produces up to 2624 lbs. (1193 Kgs.)* of ICE per day✓ Constructed from sturdy, corrosion-resistant 300 series stainless steel ✓ Only 26 inches tall✓ Available with an air-or water-or remote-cooled condenser …

• Mellerware ICE MASTER ICM001BKA (6 pages) Register onlineNever lose your receipteNemakes life easierICE MASTERblack icemaker, Model:100WICM001BKABullet shaped ice cubesProduction capacity: 12kg/24HrsViewing window_IM.indd 1 5/22/2014 3:57:32 PM …

• Icematic F 80 C (33 pages) Cod. 71503496/0- Rev. 001 - 04/2008I NOSTRI IMPIANTI SONO CONFORMI ALLA DIRETTIVA 73/23 CEE - 89/336SERVICE MANUALELECTRONIC MODULARFLAKERS AND SUPERFLAKERSF 80 CF 125 CF 120F 200SF 300SF 500SFN 1000Gas R134a - R 404aNEW PC BOARD VERSION …

• Frigidaire FGHS2655PF6B (2 pages) SERVICE DATA SHEETA01461102ICE & WATER - AUTOMATIC DEFROSTSIDE BY SIDE - R134a CAUTIONAll electrical parts and wiring must be shielded from torch flame. DO NOT allow torch to touch insulation; it will char at 200°F and flash ignite (burn) at 500°F. Excessive heat will distort the plastic liner.DIAGNOSTIC MODEActivate: Press ^ and V temperature pads …

• Avanti PIM25SS (22 pages) ICE MAKER/MAQUINA DE HACER HIELO INSTRUCTION MANUAL/MANUAL DE INSTRUCCIONES Model Number / No. de Modelo: PIM25SS BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. La sección en español empieza en la página 15. Avanti has a policy of continuous improvement on its products and reserves the right to change mat …

Comments, Questions and Opinions: