GE FTP 1000 - Security Concord LCD Touchpad Installation Manual

Text of GE FTP 1000 - Security Concord LCD Touchpad User Guide:

• Copyright Copyright © 2005, GE Security Inc. All rights reserved. This document may not be copied or otherwise reproduced, in whole or in part, except as specifically permitted under US and international copyright law, without the prior written consent from GE. Document number/revision: 466-2231A (December 2005). Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT

• GE FTP 1000 - Security Concord LCD Touchpad, 1 Preface This is the GE FTP-1000 Installation Manual for model 600-1020. This document includes an overview of the product and detailed instructions explaining: • how to install the touchpad; and • how to program the touchpad. There is also information describing how to contact technical support if you have questions or concerns. To use this document effectively, you should have the following minimum qualifications: • a basic knowledge of security systems and components; and • a basic knowledge of electrical wiring and low-voltage electrical connections. Read these instructions and all ancillary documentation entirely before installing or

• GE FTP 1000 - Security Concord LCD Touchpad, FTP-1000 Installation Manual 2 Product overview The FTP-1000 lets you control the operation of compatible security systems (see Table 4 on page 10). The large display provides easy to read messages to indicate the current status of the system. The touchpad includes police, fire, and auxiliary panic buttons that can be activated anytime. A built-in speaker provides alarm, status, and button-press sounds. A swing-down door reveals a label with basic system operating commands. The door can be removed by simply opening it past its stop point. The door can also be reattached later

• GE FTP 1000 - Security Concord LCD Touchpad, 3 Installation Use the following instructions to install and wire your touchpad. Guidelines • Mount the touchpad in an environmentally controlled area (32 to 120°F or 0 to 49°C). • When mounting the touchpad, allow at least 3 inches below it for the swing-down cover. • Do not exceed the maximum available power. See the panel installation instructions for maximum available power. • Table 1 describes the power used by the touchpad. • Table 2 describes the maximum wire lengths allowed between the touchpad and the panel. Mounting plate installation To install the mounting plate, do the following: 1.

• GE FTP 1000 - Security Concord LCD Touchpad, FTP-1000 Installation Manual 4 2. For wall mounting, place the mounting plate on the wall and mark the mounting holes (see Figure 2). Be sure to leave a 3-inch clearance below for the touchpad door to open. Figure 2. Mounting hole locations 3. Insert anchors into the wall at the marked locations where studs are not present. 4. Align the mounting plate holes with the wall or gang box screw holes and secure the back plate using the screws provided. Note: Do not overtighten screws or the mounting plate may bind and prevent the touchpad from mounting properly. 5. For wall-mount installations, cut a hole in the wall behind the mounting plate

• GE FTP 1000 - Security Concord LCD Touchpad, 5 Figure 3. Touchpad wiring connections Attaching the touchpad to the mounting plate Align the tabs at the top of the mounting plate with the slots on the touchpad and swing the touchpad bottom toward the mounting plate. Gently tighten the screw into the bottom of the touchpad. Power-up and bus communication After making all wiring connections from the touchpad to the panel, you are ready to power up the panel and verify correct communication between the touchpad and the panel. Upon power-up, the panel scans the bus for connected devices and automatically learns the unit number of each bus device. Note: If you plan to install systems with no alphanumeric touchpads, we recommend that

• FTP-1000 Installation Manual 6 Testing Use the following procedures to test the touchpad for display function, button function, and system operation. Test touchpad display function Press and hold the 4, 5, and 6 buttons together for about three seconds, then release them. The touchpad cycles though all text messages, then returns to the time display. Test button function To test the button functio

• GE FTP 1000 - Security Concord LCD Touchpad, 7 Adjusting display brightness You can adjust the background lighting (provided by yellow LEDs) of each touchpad individually to help compensate for lighting conditions at the touchpad location. The brightness adjustment lightens or darkens the display background and button lighting. Adjust display background brightness To adjust display background brightness, do the following: 1. Enter user programming mode by pressing 9 + system master code. The display shows SYSTEM MENU, then TIME - dATE. 2. Press A or B until the display shows OPTIONS, then press #. The display shows dOWnLd ON. 3. Press A or B until the display shows BRIgHT 2 (default setting). 4. Enter a setting from 0 (LEDs of

• GE FTP 1000 - Security Concord LCD Touchpad, FTP-1000 Installation Manual 8 Changing chime and trouble beep tones The frequency (pitch) of chime and trouble beep tones from each touchpad can be adjusted to a more desirable or distinct tone, and to compensate for hearing impaired persons. Note: Chime and trouble beep tones sound (using the default frequency) during, or within 15 seconds of any button activity at that specific touchpad. Change status tone pitch To change the status tone pitch, do the following: 1. Press and hold the * and 0 buttons together until you hear a steady tone, then release the buttons. 2. Press and hold 1 to lower the pitch or press and hold 2 to r

• GE FTP 1000 - Security Concord LCD Touchpad, 9 Troubleshooting The following describes what to do if the touchpad does not operate correctly. • The touchpad doesn’t power up (no display and no beeps when buttons are pressed). 1. Check for correct wiring connections at touchpad and panel terminals. 2. Make sure that the panel battery is connected correctly and that the panel transformer is plugged in. 3. Make sure panel transformer is not plugged into an electrical outlet controlled by a switch. Relocate the transformer to an unswitched outlet location, if necessary. • The touchpad display appears blank, but beeps sound when

• GE FTP 1000 - Security Concord LCD Touchpad, FTP-1000 Installation Manual 10 Appendix A Specifications and notices Note: See specific panel installation instructions for complete UL installation requirements for the system you are installing. Radio interferance information to the user If this equipment causes harmful interferance to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interferance by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the affected equipment and the

Related Products and Documents (Monitor):

Comparable Devices:

Similar Resources:

• Christie I Series (9 pages) Coolant Refill Instruction Sheet 1 of 9020-100686-01 Rev. 1 (03-2011) Coolant RefillInstruction SheetINTRODUCTIONThe following procedure should be performed whenever the coolant system needs to be refilled. NOTICE: Never allow the pump to run dry to avoid damaging it.KITS REQUIRED• #003-001837-xx Coolant Refill Kit (includes JeffCool E105 jug of coolant, …

• KUSSMAUL 091-84-DS (7 pages) INSTRUCTION MANUALKUSSMAUL ELECTRONICS CO., INC.170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796FILE: 091-84.P65 date: 06-02-99TEL: in NY 631-567-0314 TOLL FREE: 800-346-0857 FAX: 631-567-5826ENGINE IDLER MODULEPART OF A HIGH IDLE SYSTEM3 YEAR WARRANTYENGINE IDLERMODEL #091-84-005VOLTGAE MONITORMODEL #091-84-004 …

• Bender LIM2000plus LIM2000-1 (12 pages) TGH 1337 Edition 01/06Operating Manual LIM2000plus™Line Isolation Monitor LIM2000-1 LIM2000-1CB LIM2000-3CB …

• Samsung HP-S4253 (144 pages) Owner’s InstructionsHP-S4253HP-S5053This device is a Class B digital apparatus.Register your product at www.samsung.com/global/registerBN68-00991B-00Eng(001,144) 2/1/06 9:23 AM Page 3 …

• PureAire 99174 (45 pages) PureAire CO2 Monitor Instruction Manual Part Number 99174 CO2 range 0-50,000ppm 1140 Ensell Road Lake Zurich, Illinois 60047 Phone: 847-726-6000 Fax: 847-726-6051 Toll-Free: 888-788-8050 pureairemonitoring.com …

• MCO Home MH9-CO2-WD (4 pages) www.mcohome.com User ManualMCOHome Technology Co., Ltd 1 CCOO22 MMoonniittoorr MH9-CO2-WD Introduction MCOHome CO2 Monitor is an air quality detector which compatible with Z-Wave technology, it is mainly used to monitor CO2 concentration in industrial, agricultural, and residence environment, while monitoring the indoor temperature, humidity and VOC ( …

Comments, Questions and Opinions: