Sitecom WL-405 Manual 

Text of Sitecom WL-405 User Guide:

• 4. Appendix 4.1 Specification  Camera/Image:  Dual Mode: MPEG4 and Motion-JPEG Image Video  Multiple Profile: Output M-JPEG and MPEG4 at the same time  Multi-Area motion detection.  Fixed Focus Lens  Supports Up to 30 fps Video Frame Rate  Event Trigger: Mail & FTP  High Speed Hardware-Based Image Compression  Utility:  In

• 2.2.6 Scan If you have more than one camera configured, and you wish to switch the displaying image between cameras, you can click ‘Scan’ button to switch between all configured cameras. Click ‘Scan’ button once to activate scan function (scan icon will become blue ), click again to stop scanning (scan icon will become white ).

• Sitecom WL-405, 2.2.3 General Options You can set system-wide settings of this IP camera surveillance software in this menu. 2.2.3.1 'General Tab' All general settings like file storage directory and recording spaces can be set here. Item Description Data Directory Set the directory (folder) you wish to store the recorded video and captured image. You can click ‘Browse’ button to pick a directory in your hard disk. Free Recording Space Displays remaining storage space. Max Video File Size Defines the maxi

• Sitecom WL-405, The descriptions of every setting in motion detection menu will be given below: Item Description Region1 / Region2 / Region3 Check the box to enable / disable a certain motion detection area. Sensitivity Control the detection sensitivity of motion detection of respective motion detection region. When sensitivity is higher, small changes in image will cause IP camera to send a Email / FTP notification; if you received too much unwanted notification, try to set sensitivity to a lower value. Refresh

• Sitecom WL-405, 3.8 Wireless Settings If you wish to use wireless network instead of wired network connection, you have to set the wireless LAN parameters here. You can access this menu by clicking ‘Network Setup’ on the top of web management interface, and opening the 'Wireless Settings' tab. The descriptions of every setting in this menu will be given below: Item Description Self PinCode A random 8-digit code will be displayed here. If the wireless AP you wish to connect supports WPS-PIN, please input this code to the AP you wish to connect. This code changes every t

• Sitecom WL-405, When the Admin-utility is installed, it can be found in the start-menu, via “START > Programs > Internet Camera > IPCam Admin Utility” The Admin utility will detect all IP-camera's on your network. If the camera isn't detected, click the “Scan”-button.  Double-click on the IP-camera in the list, to open the camera web-interface in your default browser.  Select the IP-camera, and click “Config” to configure the network settings. A login dialog is shown. Enter the use

• Sitecom WL-405, 2.2.3.2 'E-Mail Settings tab' If you want to use motion detection function and wish to get an email that contains the image captured by the camera, please setup your email related parameters here first. Item Description E-Mail Subject Specify the subject of sending email. Recipient E-Mail Address Here lists all email addresses you set. New Click this button and you’ll be prompted to input the email address. Click ‘OK’ to save changes. Edit Select an email address from ‘Recipient E-Mail Address’ box, and click ‘Edit’ to edit the email address. Delete Delete selected email

• Sitecom WL-405, 2.2.7 Zoom-in / Zoom-out For cameras that support zoom-in / zoom-out function, you can use this function to see more objects that fall in the scope of camera’s view, or enlarge the image size of a certain object to see its detail. Please select a camera in video displaying area by clicking on its image, then click button to see more objects that fall in the scope of camera’s view, or click to enlarge the image size of a certain object to see its detail.

• Sitecom WL-405, 2.2 Viewer Utility The IP camera surveillance software provides various functions like video recording, after this software is installed, you can use your IP camera to safeguard your property. Please follow the following instructions to install the surveillance software. Select “Install Viewer-Utility” to start the installation of the viewer utility. Note: When the Viewer utility is installed, the ActiveX control for Internet Explorer is also installed.

• Sitecom WL-405, 2.2.2.2 Schedule Recording In this tab, you can setup scheduled video recording, so you can record the video captured by all cameras you have by a pre-defined schedule. Here are the descriptions of all setting items: Item Description Channel Select the channel number you wish to set. One Time Schedules You can specify the one-time schedule for selected camera; this schedule will be executed once only. New (One Time Schedules) Click this button and a new window will appear: Please specify the time duration of this one-time schedule (th

• Sitecom WL-405, Note: If you’re prompted by a windows security alert which asks you if you want to block ‘IPCamViewer’ program, please click ‘Unblock’ button, or IP camera surveillance software will not be able to function correctly. 2.2.2.1 'Camera' tab In this tab you can configure all cameras you wish to connect. Up to 16 cameras can be connected simultaneously: Here are the descriptions of all setting items: Item Description Channel Select the channel number you wish to set. Camera Search All cameras found on your local network will be displayed in ‘Camera Search’ box.

• Sitecom WL-405, storage spaces on Email and / or FTP server. Mail snapshot Select ‘Yes’ to send a picture to the Email address you specified in ‘E-Mail & FTP’ menu when a motion is detection, and select ‘No’ to disable this function. E-Mail Subject Set the subject of Email being sent here. This will help you to distinguish the Email sent by this IP camera from others. Send snapshot file to FTP Select ‘Yes’ to send a picture to the FTP server you specified in ‘E- Mail & FTP’ menu when a motion is detection, and select ‘No’

• Sitecom WL-405, Package Contents The following items should be included: If any of these items are damaged or missing, please contact your dealer immediately. 1. IP-Camera 2. Power Adapter 3. Ethernet Cable 4. Quick Installation Guide 5. Driver & Manual CDROM 6. Wall Mount

• 2.2.8 Snapshot You can take a snapshot of selected camera and save it to ‘Snapshot’ sub-folder of pre- defined data directory. Click the snapshot button once to take a snapshot; you can take as much snapshot as you want before hard disk is full. 2.2.9 Recording You can start video recording of selected camera manually by clicking ‘Start Recording’

• Sitecom WL-405, Description for LED indicators LED Power Link Status Remark Booting Flash Flash System Ready On Off LAN connected On On Data transferring On Quick Flash Activate WPS, push button for less than 5 sec. On Slow Flash The configuration should be finished within 120 sec., after that the Link Status LED will go back to the original status Reset to default, push button for longer than 10 sec. Quick Flash On 2 LEDs will turn off when reset to default is taken effect then system will start booting Power LED Link LED

• Sitecom WL-405, 3.12 Firmware Update The descriptions of every setting in this menu will be given below: Item Description Upgrade Firmware If you downloaded latest firmware file from our website, you can click ‘Browse’ button to pick the firmware file you wish to use. Then click ‘Upgrade’ button to start firmware upgrade procedure. It’s recommended to use wired Ethernet connection when you use this function, and DO NOT DISCONNECT OR CLOSE THE WEB BROWSER DURING UPGRADE! Reset Clear all settings in the camera. Please think again before you do this, and then click this button to reset all settings. NOTE: IP address will be reset to default value ‘192.168.0.23

• Sitecom WL-405, You can set to ‘Adhoc’ when you don’t have any wireless access point, but your computer has wireless network card. Set to ‘Infrastructure’ when you have wireless access point, and you have computers with wired network connection. Available Networks Here all wireless access points found by this IP camera are shown. Please note that sometimes, not all available access points will be displayed. If the access point you wish to connect to doesn't appear, you may have to click the ‘Refresh’ button. The descriptions of all fields is listed below: Conne

• 2.2.2.3 Motion Recording With this function activated, only motions captured by the camera will be recorded, so you don’t have to waste hard disk storage space on images you don’t need to pay attention to. Here are the descriptions of all setting items: Item Description Channel Select the channel number you wish to set. Enable Enable motion record functio

• Sitecom WL-405, Locate the IP Address of this IP Camera Connect your IP Cam by cable on your router open the admin utility, and click on the “Scan button” You will see the IP address of the IP Cam and the hostname. If the IP Cam isn’t connected to a router / DHCP server (see chapter 4.2)

• Sitecom WL-405, Select ‘Internet Protocol (TCP/IP)’, then click ‘Properties’. In ‘IP address’ field, please enter any IP address that begins with ‘192.168.0’, and ends with a value greater than 2 and less than 254 (You can use the example in the picture ‘192.168.0.239’). In Subnet mask field, please fill ‘255.255.255.0’. Please keep all other fields empty, and click ‘OK’.

• Sitecom WL-405, Camera Installation Please follow the following instructions to configure your IP camera:  Unpack the product package and check if anything is missing.  Insert the supplied LAN cable into the ‘LAN’ jack. You can skip this step if you’ll only use the wireless network.  Plug the power adapter into a wall socket, and connect the power connector to the power jack located at the back of the IP camera.  Connect your tripod to tripod connector or place the camera in a secure place, and point the camera to the place

• Sitecom WL-405, 2. Using the surveillance software When the CDROM is inserted into the CDROM player, the CD-Menu will automatically start. (If it isn't started automatically, go to 'My Computer' > 'X:' (where X: is the drive letter of the CDROM player) > open the 'Menu' folder > double click on 'CDMenu4.exe') 2.1 Admin utility The Admin-utility can be used to detect the camera on the network, and to easily change the cameras network-configuration. Select “Install Admin-Utility” in the CD- Menu, to start the installation.

• Sitecom WL-405, 3.7 Network Setup All network-related settings can be found in this menu, and you have to specify TCP/IP parameters in this menu if you want to change IP address, use PPPoE, Dynamic DNS, and activate UPnP function. You can access this menu by clicking ‘Network Setup’ on the top of web management interface, and opening the 'Network Settings' tab. 3.7.1 LAN You can define IP address and select the port number you wish to use here. The descriptions of every setting in this men

• Sitecom WL-405, Please note you must set a schedule that will be happened in the future, you can not set a schedule in the past. Edit You can modify a scheduled recording item. Select a schedule in ‘One Time Schedules’ list, and click ‘Edit’ button to edit the start and end time of this schedule. Delete Delete a selected schedule item. New (Weekly Schedules) Click this button and a new window will appear: You can define recording schedule that will be executed at the specified time of certain weekday(s) in a week. Please check all weekdays that applies, and set the start time in ‘From’

• Sitecom WL-405, 3.9 FTP and E-Mail Settings This IP camera is capable to send an Email or perform FTP upload with captured image, when a motion is detected. This is very convenient since IP camera will guard the environment automatically for you, and you don’t have to look at the monitor all the time. You can access this menu by clicking ‘Network Setup' on the top of web management interface, and opening the 'FTP and E-Mail settings' tab. 3.9.1 E-Mail settings These settings are used to send the captured picture via Email: Item Description Recipient E-Mail Address Input the email recipient’s Email address here. If you have mo

Related Products and Documents (IP Camera):

Comparable Devices:

Similar Resources:

• Panasonic OneHome BB-HCM311A (9 pages) HomeLogic LLC  100 Hoods Lane  Marblehead, MA 09145  Phone (781) 639-5155  Fax (781) 639-9677 OneHome Camera Integration Note Manufacturer: Panasonic Model Number(s): BB-HCM311A, BB-HCM331A, KX-HCM110A OneHome Versions: 3.0 (all builds), 4.0 ( …

• INSTEON 2864-232 (2 pages) Connect your camera to power and your router.Branchez votre caméra à une source d'alimentation C.A. et à votre routeur.1Mount the bracket using screws and wall anchors1Installez le support de fixation à l'aide des vis et des ancrages muraux.3Launch the Insteon app and select Add a Camera3Lancez l'application d'Insteon et choisissez l& …

• Kerbl 81890 (72 pages) IPCam Pet#81890(DE) Bedienungsanweisung(FR) Mode d’emploi(EN) Instructions for use(PL) Instrukcja obslugi(CS) Návod k obsluze(NL) Gebruiksaanwijzing(IT) Istruzioni per l’uso …

• Medion S49014 (210 pages) 07/2016WildkameraWildlife CameraCaméra de surveillance extérieur infrarougeWildcameraMEDION® S49014 (MD 87586)BedienungsanleitungUser ManualMode d‘emploiHandleiding …

• Edimax IC-3116W (3 pages) The Edimax IC-3116W 720p wireless network camera is a versatile monitoring device ideal for monitoring your home, shop or factory during the daytime or at night. With Edimax Plug-n-View technology, no complicated setup is required and you can easily connect the camera to the cloud and monitor remotely from a smartphone, tablet or laptop. Motion-trigg …

• Perenio PEIFC01 (10 pages) Doc Date: August 31, 2020 Version: 2.1.1 ©Perenio IoT spol s r.o. All Rights Reserved 1 Dear Customer, thank you for choosing Perenio® products! The Indoor Fixed Camera is specially designed for video surveillance and motion detection in the area of installation. It is used as part of the Perenio Smart Building Management System. The …

Comments, Questions and Opinions: