Panasonic NV-FJ710 Series Operating Instructions Manual

Text of Panasonic NV-FJ710 Series User Guide:

• Panasonic NV-FJ710 Series, 17 Playback 30 (min.) 240 (min.) 180 (min.) 120 (min.) 60 (min.) Counter display (normal playback mode) ≥ Repeatedly pressing this button changes the indication in the following order: To Stop Midway: Press the Stop button 9. To Play Back NTSC Video Cassettes on Your PAL TV (Quasi-NTSC Playback Function) This VCR allows playback of tapes recorded in the NTSC system on a normal PAL system TV with the same operations as usual. On some TVs, however, the playback picture may roll up or down. ≥ If your TV has a V-HOLD control or

• 22 To Programme with the ShowView Function The ShowView numbers assigned to each TV programme and published alongside the TV programme listings in newspapers and magazines make it extremely easy to set the VCR for timer recording. The duration of a timer recording programmed with ShowView number may be slightly longer than the actual duration of the TV programme. P

• Panasonic NV-FJ710 Series, 39 Advanced Operations Hint: ≥ If you select “RF” in step 3, “Satellite – Position” is set automatically and it is not possible to change the satellite programme position here. If you want to change it, refer to page 41. Note: ≥ If your satellite receiver is not included in the list of compatible satellite receivers, this VCR cannot control it. To Prepare the VCR for Remote-controlled Operation of the Satellite Receiver (Setting the Tuner Type) This VCR lets you change the programme position on the satellite receiver and programme timer recordings of satellite programmes—all with this VCR’s remote control. This is calle

• Panasonic NV-FJ710 Series, 25 Timer Recording To Cancel the Programming of a Timer Recording It is not possible to cancel a programming while the timer recording is being performed. ≥ Display the VCR picture on the TV. ≥ Set the VCR/TV switch P to “VCR”. 1 Press the PROG./CHECK button < to display the timer recording programmings on the TV screen. 2 Press the Cursor buttons (34) R to select the programming that you want to cancel. 3 Press the CANCEL button >. 4 Press the EXIT button S to exit the On Screen Display. Notes for Cancelling the Programming of a Timer Recording In some cases, for example as listed below, the programming of a timer recording remains stored in

• 10 Connecting and Preparations for a TV Equipped with the Q Link Function Connections and preparations for a TV equipped with the “Q Link”° 1 function and equipped with a 21-pin Scart socket. For the connections and preparations for a TV equipped with the “DATA LOGIC”° 2 , “Easy Link”° 3 , “Megalogic”° 4 or “SMARTLINK”° 5 function and with a 21-pin Scart socket, al

• 48 Other Convenient Functions (Various Settings) Settings for the Main Menu Item “Display” For Automatic Display of the Channel Guide on the TV Screen Each Time You Change the Programme Position 1 Press the MENU button U to display the Main menu on the TV screen. 2 Press the Cursor buttons (3421) R to select “Display”, “Channel Guide” and the entry field f

• Panasonic NV-FJ710 Series, 43 Various Settings 4 Press the Cursor buttons (3421) R to select the TV station whose subtitle Teletext page number you want to change. 5 Press the OK button T to display the Manual Tuning menu. 6 Press the Cursor buttons (3421) R to select the entry field for “Subtitles”. 7 Press the Numeric buttons 2 or the Cursor buttons (34) R to select the correct Teletext page number. 8 Press the OK button T to conclude the setting. 9 Press the EXIT button S to exit the On Screen Display. To Set the Subtitle Teletext Page Number When Recording a Satellite TV or Pay-TV Programme: The subtitle Teletext page numb

• Panasonic NV-FJ710 Series, 5 Before Use ∏ Remote Control∏ Operating Instructions ∏ Satellite Receiver List ∏ RF lead to connect VCR and TV 1 2 - - + + 3 Checking the Accessories/Preparing the Remote Control Inserting Remote Control Batteries 1 Slide off the battery cover. 2 Insert the batteries with the polarity (+ and -) correctly aligned. 3 Replace the battery cover. ≥ Do not heat or short-circuit the batteries. ≥ When you do not use the remote control for a long time, take out the batteries and store them in a cool, dry place. If the Sliding Cover of the Remote Control Become

• Panasonic NV-FJ710 Series, 29 Tape Library System 09 Press the Cursor buttons (34) R to select the desired category and then press the OK button T. 10 Press the MENU button U. 11 Press the OK button T. ≥ When you enter (or change) the title, the recording start time, which was displayed before, disappears. 12 Press the EXIT button S to exit the On Screen Display. 0 To Manually Enter or Editing a Title or Category If you press the LIBRARY button M when no cassette is inserted, operation steps 1 and 2 below are not necessary. In this case, start from operation step 3. 01 Press the MENU button U and then press the Curs

• Panasonic NV-FJ710 Series, 40 ≥ Some satellite receivers offer less than 99 channels. In this case, the number of the satellite channels that can be controlled from the VCR is the same. ≥ Some satellite receivers offer more than 99 satellite channels, but even in this case, only the satellite channels 1 through 99 can be controlled from the VCR. ≥ With some satellite receivers, it is necessary to wait a few seconds between selecting one channel and selecting another one with the remote control of the VCR. ≥ If the display on the satellite receiver does not indicate the channels, refer to its operating instructions and follow the procedure for displaying the channels. To Prepare th

• Panasonic NV-FJ710 Series, 24 To Change a Timer Recording Programming It is not possible to change a programming while the timer recording is being performed. ≥ Display the VCR picture on the TV. ≥ Set the VCR/TV switch P to “VCR”. 1 Press the PROG./CHECK button < to display the timer recording programmings on the TV screen. 2 Press the Cursor buttons (34) R to select the programming that you want to change. 3 Follow the operations below to change the programmed contents. To change the broadcasting station: Use the Channel buttons :. To change the date of the timer recording: Use the DATE button ;. To change the recording starting time: Use

• Panasonic NV-FJ710 Series, 4 VCR Operation When you want to operate the VCR, set the VCR/TV switch P to “VCR”. °2 Numeric buttons To select the programme positions (1–99) of the VCR. Example: 9: 19: To select the satellite programme positions Example: SAT 9: SAT19: SAT129: ≥ 3-digit programme positions can be selected with this remote control only in case of a satellite receiver that is marked with (° 1 ) on the enclosed list of compatible satellite receivers. To enter a ShowView number. To enter numbers for various settings. °A VCR 1/2 switch Set to the

• Panasonic NV-FJ710 Series, 28 To Check the Tape Library’s Contents by Cassette Number, Title, Category, or Recording Date If you press the LIBRARY button M when no cassette is inserted, operation steps 1 and 2 below are not necessary. In this case, start from operation step 3. 1 Press the MENU button U and then press the Cursor buttons (341) R to select “Tape Library” and “Library contents” in this order. 2 Press the OK button T. 3 Press the Channel buttons (red) :, DATE button (green) ;, ON button (yellow) G or OFF button (blue) F . Pressing the above buttons displays a list of the recorded programmes as

• 38 2 1 Connecting the VCR to a Satellite Receiver or Digital Receiver Satellite receiver here includes a digital receiver. The connection method differs depending on the type of your satellite receiver. For details about the connection, also read the satellite receiver’s operating instructions. If the Satellite Receiver is Equipped with a 21-pin Scart Socket If your s

• Panasonic NV-FJ710 Series, 7 Before Use As this equipment gets hot during use, operate it in a well ventilated place; do not install this equipment in a confined space such as a book case or similar unit. IMPORTANT Your attention is drawn to the fact that the recording of pre-recorded tapes or discs or other published or broadcast material may infringe copyright laws. WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. FOR YOUR SAFETY ª DO NOT REMOVE OUTER COVER. To prevent electric shock, do not remove cover.

• Panasonic NV-FJ710 Series, 33 Advanced Operations Assemble Editing The assemble editing function makes it easy to record the picture and sound of virtually any number of scenes or programmes in succession. Assemble editing from an external source, for example from a video movie camera, can be performed in the same way. Editing 5 When that point is reached, press the Pause/Slow button 7 again to start recording the new picture and sound from the playback unit. 6 To record (copy) additional scenes, press the Pause/ Slow button 7 to put this VCR in the recording pause mode and then perform steps 4 and 5 again. 7 At the point where y

• Panasonic NV-FJ710 Series, 6 Be sure to read the cautions carefully before you operate this VCR. Avoid sudden changes in temperature If the VCR is moved suddenly from a cold to a warm place, condensation may form on the tape surface and inside the VCR. If this happens, leave the VCR at room temperature for at least 1 hour before operating it. Avoid humidity and dust Do not use the VCR in very humid or dusty places. This may cause damage to its internal parts. Do not cover the ventilation holes The ventilation holes prevents excessive heat build-up inside

• Panasonic NV-FJ710 Series, 56 √ Recording Is Not Possible or Does Not Work Properly The symptom descriptions are given between quotation marks “”. “When recording is attempted, the 1 indication flashes.” ‘ A video cassette with a broken out erasure prevention tab is used. Use a cassette with an intact tab, or if you want to erase the previously recorded contents on the cassette, cover the tab hole with two layers of adhesive tape. “The playback picture of a recorded programme is distorted or no picture can b

• Panasonic NV-FJ710 Series, 11 Connecting and Setting Up Preset Download Function The Preset Download function automatically copies the tuning position of all available TV stations into the VCR’s memory when you connect the VCR using a fully-wired 21-pin Scart cable to a TV equipped with the Q Link function. To Simultaneously Set Up this VCR with a New TV Perform the following operation steps exactly as described to ensure that the Preset Download function works correctly. √ First of all, make sure that the VCR is switched off. 1 Switch the TV on. The TV starts to tune all available TV stations and to adjust the clock. (This is called A

• Panasonic NV-FJ710 Series, 41 Various Settings Tuning and Assigning the TV Stations Available in Your Area to the Programme Positions (Manual Tuning) This VCR has 99 programme positions that can be preset to receive TV stations. Usually, if you switch the VCR on for the first time after making the necessary connections, the VCR will start the Download or Auto Setup function automatically so that all available TV stations in the area can be received. However, if Auto Setup is not successful due to extraordinary transmission circumstances, or if you want to change the name of a TV station or change a TV station from its regular programme position to one o

• Panasonic NV-FJ710 Series, 55 Helpful Hints Before Requesting Service Before requesting service, please check the following points. √ On Screen Display Messages The error messages are given in brackets [ ]. [Please insert video tape!] ‘ You pressed the REC button J (REC/OTR button c), the DIRECT TV REC button 6, the Play button I, the Fast Forward button H or the Rewind button 8 when no cassette was inserted in the VCR. You pressed the TIMER REC button D when no cassette was inserted in the VCR with a timer recording programmed. Insert a video cassette. [Pl

• Panasonic NV-FJ710 Series, 20 To Manually Adjust the Audio Recording Level This VCR adjusts the recording level automatically to prevent sound distortion due to excessive peaks. However, if you want to manually adjust the audio recording level, perform the operation steps below before you start the actual recording. We recommend you to adjust the level so that it peaks at approximately i4 dB on the recording level indicator. 1 Before recording, press the AUDIO button ?. 2-a To adjust the left (L) and right (R) channels simultaneously: Press the Cursor buttons (21) R to adjust the audio recording level. 2-b To adjust the left (L) and right (R) channels individually, use either of the following two operation

• Panasonic NV-FJ710 Series, 35 Advanced Operations A.DUB A.DUB 1 2 3 5 6 Preparations ≥ Connect the audio equipment or a video movie camera to this VCR with an audio cable. ≥ Display the VCR picture on the TV. ≥ Insert the cassette on which the audio dubbing is to be performed, and make sure that its erasure prevention tab is not broken out. As soon as the cassette is inserted, the Cassette Number Check starts. Wait a few moments until it is completed. (See page 15.) ≥ Press the INPUT SELECT button 3 to select the AV Input (external input) “A1”, “A2” or “A3” according t

Related Products and Documents (Car Stereo System):

Comparable Devices:

Similar Resources:

• Panasonic CQ-C7413U? CQ-C7113U (38 pages) 2Safety InformationCQ-C7413U/C7113UWarningObserve the following warnings when usingthis unit.❑The driver should neither watch the display noroperate the system while driving.Watching the display or operating the system will distractthe driver from looking ahead of the vehicle and can causeaccidents. Always stop the vehicle in a safe location and usethe par …

• Pioneer DEH-P680MP - In-Dash CD/MP3 Player (152 pages) Operation ManualMode demploiMulti-CD control High power CD/MP3/WMA/AACplayer with FM/AM tunerSyntoniseur FM/AM et lecteur de CD/MP3/WMA/AAC, Puissance élevée, avec contrôleur pour lec-teur de CD à chargeurDEH-P680MPEnglish Français …

• Sony RC-202iPV (2 pages) 4-270-598-11(1)USB and Video connection cable for iPodInstructionsMode d’emploiInstruccionesAnleitungIstruzioniInstructiesИнструкцииІнструкції©2011 Sony Corporation Printed in ThailandAvis à l’attention des clients : les informations suivantes s’appliquent uniquement aux appareils vendus dans des pays qui appliquent les directiv …

• Blaupunkt Hamburg MP68 (35 pages) Hamburg MP68 7 648 012 310Operating and installation instructionsMode d’emploi et de montageInstrucciones de manejo e instalación Instruções de serviço e de montagem 操作及安裝手冊사용 및 장착 설명서사용 및 장착 설명서www.blaupunkt.comCar Radio CD MP3 WMA01BA_HamburgMP68us_gb.indd 101BA_HamburgMP68us_gb.indd 1 14.03.20 …

• Rockford Fosgate 3Sixty (6 pages) Set Up GuideFirst, before anything else you need to ensure the audio connections are correct and that you have tested and documented the maximum useable output voltage and volume position of the source unit, either aftermarket or OEM. It does not matter if you are connecting your signal outputs from the source unit to a the 3Sixty through high level or pream …

• Sony CDX-GT350MP - Fm/am Compact Disc Player (2 pages) CDX-GT350MPCDX-GT350MP CD Receiver The easy-to-read single line LCD display shows clock, station ID and track data when playing back your digital MP3/WMA filesfrom the internal CD drive. Front auxiliary input lets you connect almost any portable audio device to your car's sound system.1 Play CDs, CD-Rs, and CD-RWs, including discs loaded with digi …

Comments, Questions and Opinions: