Manualios.com

Panasonic KX-TG2227S Operating Instructions Manual

Panasonic KX-TG2227S Manual Online:

4.6, 2795 votes
Panasonic KX-TG2227S User Manual
Panasonic KX-TG2227S User Guide
Panasonic KX-TG2227S Online Manual

Text of Panasonic KX-TG2227S User Guide:

  • Panasonic KX-TG2227S, Preparation Cordless Telephone Answering System Useful Information 2.4GHz Digital Cordless Answering system Model No. KX-TG2227S Pulse-or-tone dialing capability Operating Instructions Charge the battery for about 15 hours before initial use. PLEASE READ BEFORE USE AND SAVE. Panasonic World Wide Web address: http://www.panasonic.com for customers in the USA or Puerto Rico

  • Panasonic KX-TG2227S, 8 Base unit display The clock needs adjusting (p. 18). Your greeting or memo message was not recorded correctly. Record it again (p. 15, 33). The unit is in the answering system programming mode. The speaker volume level is set to “5”. You can select: —9 levels (0–8) are available while using the answering system (p. 15, 29). —8 levels (1–8) are available while using the intercom (p. 25). 12 messages have been recorded. FULL Memory is full. Erase some, or all, of the messages (p. 32). The recording time is set to “Greeting only” (p. 19). (The display is blank.) Display

  • Panasonic KX-TG2227S, 10 Settings Battery Charge Place the handset on the base unit and charge for about 15 hours before initial use. •The IN USE/CHARGE/HOLD indicator lights and a beep sounds. Installing the Battery in the Handset IN USE/CHARGE/HOLD Indicator OR Insert the battery into the handset as shown (#), matching the correct polarity. Press the battery down until it places into the compartment ($). When finished, close the cover. 2 1

  • Panasonic KX-TG2227S, 12 Dialing Mode You can program the dialing mode using the handset near the base unit. If you have touch tone service, set to TONE. If rotary or pulse service is used, set to PULSE. Your phone comes from the factory set to TONE. Make sure the unit is not being used and the handset is lifted off the base unit. 1 Press (PROGRAM). •The TALK/MUTE indicator flashes. 2 Press á. 3 To select PULSE, press (#) twice. OR To select TONE, press (*) twice. 4 Press (PROGRAM). •A beep sounds. •You can exit the programming mode anytime by pre

  • Panasonic KX-TG2227S, For product service •Call 1-800-211-PANA(7262) for the location of an authorized servicenter. •Panasonic’s e-mail address for customer inquiries: [email protected] for customers in the USA or Puerto Rico ONLY When you ship the product •Carefully pack your unit, preferably in the original carton. •Attach a letter, detailing the symptom, to the outside of the carton. Symptom •Send the unit to an authorized servicenter, prepaid and adequately insured. •Do not send your unit to the Panasonic Consumer Electronics Company listed on the back cover or to ex

  • Make sure the unit is not being used and the handset is lifted off the base unit. 1 Press (PROGRAM). •The TALK/MUTE indicator flashes. 2 Press (FLASH/CALL!WAIT/PLAYBACK). •“P” is displayed on the base unit. 3 Press (5). •The current setting is displayed on the base unit. 1: 1 minute 2: 2 minutes 3: 3 minutes Blank: Greeting only 4 Press (1), (2), (3) or (0) to select the recordi

  • 55 Useful Information For assistance, please call: 1-800-211-PANA(7262) CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits a

  • Panasonic KX-TG2227S, 25 Cordless Telephone For assistance, please call: 1-800-211-PANA(7262) Intercom A 2-way intercom is possible between the handset and the base unit. Paging the base unit from the handset 1 Handset: Press (HOLD/INTERCOM). Talk to the paged party after the beeps. •The INTERCOM/2WAY REC indicator lights. 2 Base unit: When the other party’s voice is heard, answer using the MIC. 3 To end the intercom, press (OFF) on the handset. OR Press (LOCATOR/INTERCOM) on the base unit. Paging the handset from the base unit (Handset locator) Using this feat

  • Panasonic KX-TG2227S, 34 Remote Operation from a Touch Tone Phone You can operate the answering system from any touch tone phone. A synthesized voice menu will guide you on how to operate the unit (p. 36). •To skip the voice menu and operate the unit directly, see page 38. Summary of remote operation Call your unit from a touch tone phone. Enter your remote code (p. 35) during or after the greeting message. •The number of new messages is heard. After 3 seconds, the voice menu will start (p. 36). Follow the menu or enter the direct commands (p. 38). To end remote operation, hang up. •The messages are saved. •The unit will announ

  • Panasonic KX-TG2227S, 43 Useful Information For assistance, please call: 1-800-211-PANA(7262) 4 Connect the telephone line cord. Mount the unit, then slide down. •Raise the antenna. •Fasten the telephone line cord to prevent it from being disconnected. 5 To charge the handset battery: Fix the charge contacts (#) and insert the hook to the handset hole ($). •The IN USE/CHARGE/HOLD indicator lights. 2 1 Hook Hole Hooks OR

  • 28 Automatic Answering Operation When the unit answers a call, a greeting message is played and the caller’s message is recorded. •The total recording time (including greeting message) is about 15 minutes. If messages are recorded in noisy rooms, the time may be shortened by up to 3 minutes. •A maximum of 64 messages (including greeting message) can be recorded. Setting the Unit to An

  • Panasonic KX-TG2227S, 37 Answering System For assistance, please call: 1-800-211-PANA(7262) All Message Playback All recorded messages are played back. At the end of the last message, “End of final message” is heard. The unit will announce the remaining recording time if it is less than 5 minutes. New Message Playback Only new messages are played back. At the end of the last message, “End of final message” is heard. The unit will announce the remaining recording time if it is less than 5 minutes. Recording a Memo Message You can leave a personal message. 1. Talk after you hear “Please leave your message”. 2. Wh

  • Panasonic KX-TG2227S, 14 Ringer Pattern You can select the handset ringer pattern out of 6 patterns. When an incoming call is being received, the unit rings in the selected pattern. Make sure the unit is not being used and the handset is lifted off the base unit. 1 Press Ü or á. •The unit rings at the current setting. •If you set the ringer volume to OFF, the unit will not ring. 2 Within 5 seconds, select the desired ringer pattern by pressing Ü or á. •Each time you press the button, the ringer pattern will change and ring. Ringer Volume You can program the handset ringer volume to HIGH, LOW or OFF. If set to OFF, the handset will not ring. Your phone comes fr

  • Panasonic KX-TG2227S, 42 Wall Mounting This unit can be mounted on a wall phone plate. 2 Connect the AC adaptor. 3 Tuck the telephone line cord inside the wall mounting adaptor, then push it in the direction of the arrow. •The word “UP” should face upward. 1 Push the hook and turn it around. Turn the hook until a click is heard. To Power Outlet

  • Panasonic KX-TG2227S, 9 Preparation For assistance, please call: 1-800-211-PANA(7262) Settings Connections • USE ONLY WITH Panasonic AC ADAPTOR PQLV1 (Order No. PQLV1Z). •The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) •To connect a standard telephone on the same line, see page 46. Single-Line Telephone Jack (RJ11C) Telephone Line Cord AC Adaptor Raise the antenna. Fasten the AC adaptor cord to prevent it from being disconnected. Power Outlet (AC 120 V, 60 Hz) Hook

  • Panasonic KX-TG2227S, 24 Speed Dialer Storing Phone Numbers You can store up to 10 phone numbers in the handset. The dialing buttons ((0) to (9)) function as memory stations. Make sure the unit is not being used and the handset is lifted off the base unit. 1 Press (PROGRAM). •The TALK/MUTE indicator flashes. 2 Enter a phone number up to 22 digits. •If you misdial, press (OFF) to end storing and start again from step 1. 3 Press á. 4 Press a memory station number ((0) to (9)). •A beep sounds. •To store other numbers, repeat steps 1 through 4. •If a pause is required for dialing, press (REDIAL/PAUSE) w

  • Panasonic KX-TG2227S, 17 Preparation For assistance, please call: 1-800-211-PANA(7262) Programming Summary for Answering System You can program the following functions using the handset near the base unit. See the corresponding pages for function details. Make sure the unit is not being used and the handset is lifted off the base unit. •You can exit the programming mode any time by pressing (OFF). •If you do not press any buttons for 60 seconds, the unit will exit the programming mode. Press (PROGRAM). Press (FLASH/CALL!WAIT/PLAY

  • 7 Preparation For assistance, please call: 1-800-211-PANA(7262) IN U N US E / SE/ C H CHARGE / E/ V O L VOLU M E UME MIC S K IP SKIPR E P E A T REPEAT ERASE M E M O MEMO S L O W SLOW T A L K TALK GREETING STOP KX-TGKX-TG 22572257 H O L D HOLD IN USE/CHARGE/HOLD Indicator (p. 10, 22) (LOCATOR/INTERCOM) Button (p. 25) Antenna (p. 3, 9) Display (p. 8) Charge Contacts (p. 1

  • Panasonic KX-TG2227S, 31 Answering System For assistance, please call: 1-800-211-PANA(7262) From the Handset If someone else is in the room and you want to listen to the recorded messages privately, you can use the handset. 1 Handset: Press (FLASH/CALL!WAIT/PLAYBACK). •The number of new messages is heard on the handset. 2 Base unit: To listen to messages: Press (MESSAGE!PLAYBACK/SLOW!TALK). When you have new messages: the unit announces the number of new messages and only new messages are played back. When you have no new messages: the unit announces “No new messages. All message playback” and plays back all messages. When you have no messages: the unit announces “No mes

  • Panasonic KX-TG2227S, Make sure the unit is not being used and the handset is lifted off the base unit. 1 Press (PROGRAM). •The TALK/MUTE indicator flashes. 2 Press (FLASH/CALL!WAIT/PLAYBACK). •“P” is displayed on the base unit. 3 Press (0). •“Set time” is announced from the base unit. If previously adjusted, the day/time will be heard. 4 Enter the current time (hour and minute) using a 4-digit number. (Ex. To set 9:30, enter “0930”.) •The 2 digits of the entered number is displayed. 5 Press (*) to select “AM” or “PM”. Press (#) repeatedly to set the day. 6 Press (PROGRAM). •The base unit announces the day/time. The clock starts working. •If

  • Panasonic KX-TG2227S, Location of Controls 6 Handset CH A U T O AUTO CALL L W A WAIT PAUSEUSE ALL L MSG NEW W MSG TONETONE STOP A N ANS S O FF OFF ANS S ON SK IP KIP REP E PEAT PLAY BACKAY BACK 9 8 3 2 1 6 5 4 7 0 ININTERCOM SP - PHONE HOLD REDIAL FL ASH H T A L K / M U T E R E C H A R G E IN T E R C O M / 2 W A Y R E C RINGERRINGER MUTE 2WAY REC PROGRAM Antenna (MUTE) Button (p. 26) (2WAYÒREC) Button (p. 33) (OFF) Button (p. 12, 17, 21, 25 , 40 ) (HOLD/INTERCOM) Button (p. 22, 25) (REDIAL/PAUSE) Button (p. 22, 27) (TONE) Button (p. 26) (FLASH/CALL!WAIT/PLAYBACK) Button (p. 17, 26, 27, 31, 35, 40) Navigator Key ( , , , ) ( p. 12, 22,

  • Panasonic KX-TG2227S, 47 Useful Information For assistance, please call: 1-800-211-PANA(7262) Problem An alarm tone sounds. Static, sound cuts in/out, fades. Interference from other electrical units. The unit does not ring. You cannot store a phone number in memory. While storing a phone number, the unit starts to ring. You cannot make a call with the handset. You cannot page the handset. Remedy •You are too far from the base unit. Move closer and try again. •Place the handset on the base unit and try again. •Plug in the AC adaptor. •Raise the base unit antenna. •Locate the handset and the base unit away from other electrical appliances (p.

  • Panasonic KX-TG2227S, 51 Useful Information For assistance, please call: 1-800-211-PANA(7262) Problem You cannot program items such as the dialing mode. Previously programmed information is erased. The RECHARGE indicator flashes or the unit beeps intermittently. You charged the battery fully, but the RECHARGE indicator flashes. The IN USE/CHARGE/HOLD indicator light does not go out after the battery has been charged. If you cannot solve your problem Remedy •Programming is not possible while the unit is in the talk or intercom mode, or while the answering system is in use

  • Panasonic KX-TG2227S, 16 To check the recorded greeting message Press (GREETING). To erase the recorded greeting message Press (GREETING) \ Press (ERASE) while the message is being played. •The unit will answer a call with a pre-recorded greeting. Pre-recorded greeting message If you do not record a greeting message (p. 15), one of two messages will be played when a call is received, depending on the caller’s recording time (p. 19). To check the pre-recorded greeting, press (GREETING). •A pre-recorded greeting will be played as follows: ■ When the recording time is set to “1 minute”, “2 min

Related Products and Documents (Telephone):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Kyocera TASKalfa 620 Operation manual kyocera/taskalfa-620-MBL.pdf 13 Jan 2023 176
2 Toshiba FT-8939 Service manual toshiba/ft-8939-IXO.pdf 06 May 2023 62
3 NEC ElectraElite IPK Operation & user’s manual nec/electraelite-ipk-N28.pdf 06 Feb 2024 39
4 Zte Boost MAX Operation & user’s manual zte/boost-max-ZJM.pdf 13 Jan 2024 169
5 Conair 208RC Instruction & styling manual conair/208rc-MJM.pdf 02 Jul 2023 30 1.38 Mb
6 Honeywell CT3395 Installation instructions addendum honeywell/ct3395-973.pdf 04 Aug 2022 1 0.1 Mb

Similar Resources:

  • VTech

    i6772

    (45 pages)
    Felicitaciones por su compra de esteproducto VTech¿NECESITA AYUDA?Nuestros representantes están aquí paraayudarle con cualquier pregunta que tengaacerca de la operación de este producto,de los accesorios disponibles, y cualquierotro asunto relacionado.Llame gratis al teléfono:1-800-595-9511En el Canadá, llame alteléfono:1-800-267-7377o visite nuestro …
  • Broadview

    OfficeSuite

    (36 pages)
    Administrator User GuideCONTACT SUPPORT1-888-623-VOIPO[email protected]://community.broadviewnet.comOceSuite® Phone PUTTING ALL YOUR OFFICESUITE® FEATURES TO USE TO BE MORE EFFICIENT …
  • Valcom

    V2001A

    (2 pages)
    ONE ZONE ENHANCED INTEGRATED PAGE CONTROLMODEL V-2001ADESCRIPTION:A telephone-compatible one-zone, one-way page control unit with integrated single and warble tonegenerator, power supply, and background music input.POWER REQUIREMENT1 Amp at 120 VacINPUTS/OUTPUTSInput Impedance: 600 ohmsMusic Source Impedance: 8 to 600 ohmsMusic Input Level: -10 dBm nomina …
  • NEC

    XEN TOPAZ MULTILINE TELEPHONE

    (6 pages)
    Multiline Telephone User Guide Nothing contained in this manual shall be deemed to be, and this manual does not constitute, a warranty of, or representation with respect to, any of the equipment covered. This manual is subject to change without notice and NEC Business Solutions Ltd has no obligation to provide any updates or corr …
  • Talkaphone

    VOIP-500 Series

    (6 pages)
    VOIP-500 Series Emergency Phone Quick Installation Guide Copyright 2010 Talk-A-Phone Co. All rights reserved. Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 1 of 6 Phone 773.539.1100 • Fax 773.539.1241 • [email protected] • www.talkaphone.com All prices and specifications are subject to change without no …
  • Bizfon

    680

    (1 pages)
    Forward callsEnable/Disable AfterHours AnsweringDo Not DisturbSet Speed DialRe-record your greetingRe-record your nameChange your passwordSet number of ringsTo use the Bizfon 680from outside the office:!!!!Dial your company’snumber.Press * during thegreeting.Enter your extension andpassword.Use any Bizfon 680 MainMenu function.Bizfon 680Bizfon 680Personal …

Comments, Questions and Opinions: