Godex DT2 Operation & User’s Manual

Text of Godex DT2 User Guide:

• Godex DT2, 33 DT2 / DT4 series User Manual 6-3. Labels with black marks If you are using black-mark label stock that has the printer's maximum feed width, the printer may not recognise the black marks because they are outside the sensor range. When using label stock with black marks, you should therefore observe the following restrictions: DT2 For 60 mm wide label stock, the black marks should have the following positions and sizes:  A > 13.1 mm high  B < 5mm high  C > 8.1 mm high DT4 For 118 mm wide label stock, the black marks should have the following positions and sizes:  A > 10.05 mm high  B

• Godex DT2, 12 DT2 / DT4 series User Manual 2-3. Connecting the printer to the host computer 1. Please make sure that the printer is switched off. 2. Connect the power cord to the power supply and to the AC adapter, then connect the adapter to the printer. 3. Connect the printer with the host computer via the USB port or serial port. 4. Switch on the printer. The LED indicator should light up.

• Godex DT2, 25 DT2 / DT4 series User Manual Firmware Download On “Firmware Download” tab, the current version of printer firmware will be showed on the screen. If you need to update the printer firmware, just specify the file location of firmware file and press “Start Download Firmware” button. The printer firmware then can be updated remotely. In addition to the firmware update, you can press “Recover To Factory Settings” button to restore the printer configurations back to factory default.

• Godex DT2, 32 DT2 / DT4 series User Manual 6. Maintenance and adjustment 6-1. Cleaning the print head Dirt on the print head or ribbon, or glue residue from the label liner may result in inadequate print quality. The printer cover must therefore always be closed. Keeping dirt and dust away from the paper or labels ensures a good print quality and a longer lifespan of the print head. Here is how you clean the print head: 1. Switch off the printer. 2. Open the printer cover. 3. To remove any label residue or other dirt from the print head (see blue arrow), please use a soft lint-free cloth dipped in alcohol. 【 Note 1 】 The print head s

• Godex DT2, DT2 / DT4 series User Manual 1. BARCODE PRINTER ........................................................................................ 1 1-1. Box content .........................................................................................................................1 1-2. Specifications ......................................................................................................................1 1-3. Getting to know your printer ............................................................................................7

• Godex DT2, 20 DT2 / DT4 series User Manual IP Setting The IP Setting tab can change the printer name, Port number, Gateway setting and the password for configuring the printer. You can also set the printer’s IP address ether by DHCP or by Static IP. You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. 【 Note 】 To fully benefit from the NetSetting software, you should be familiar with basic networking principles. Please contact your network administrator for related network setting information.

• Godex DT2, 31 DT2 / DT4 series User Manual 8. Close the cover on the bottom of the printer (DT2: and secure it with the screw). 9. Place the printer the right way up again. In the next step, load the label stock. 10. Follow the instructions in Section 2-1. 11. Pass the start of the label roll through the cutter and press the FEED button to finish.

• Godex DT2, DT2 / DT4 series User Manual Safety instructions Please read the following instructions carefully. 1. Keep the equipment away from humidity. 2. Before you connect the equipment to the power outlet, please check the voltage of the power source. 3. Make sure the printer is off before plugging the power connector into the power jack. 4. It is recommended that you connect the printer to a surge protector to prevent possible transient overvoltage damage. 5. Be careful not to get liquid on the equipment to avoid electrical shock. 6. For safety and warranty reasons, ONLY qualif

• Godex DT2, 11 DT2 / DT4 series User Manual 2-2. Installing the label roll holder 1. Pull the label roll holder out as far as it will go. 2. Fold out the label supply hub as shown in the illustration. 3. Now rotate the label roll holder to return the label supply hub to its original position. Press down the label supply hub until it clicks into place. A. To load label stock with a 1" core, the locking notch must be at the top of the label supply hub. B. To load label stock with a 1.5" core, the locking notch must be at the bottom of the label s

• 1 DT2 / DT4 series User Manual 1. Barcode printer 1-1. Box content Please check that all of the following items are included with your printer:  Barcode printer  Power cord  AC adapter  USB cable  Label stock  Quick reference guide  CD (with QLabel label software / user manual) DT2 series

• Godex DT2, 9 DT2 / DT4 series User Manual 2. Printer setup 2-1. Loading the label roll 1. Place the printer on a flat surface and open the printer cover. 2. Release the label supply hub. 3. Lift the label roll holder and pull it out as far as possible. 4. Install the label roll on the label supply hub. 5. Now press the label roll holder down until it clicks into place. 6. Return the label roll holder to its original position.

• 15 DT2 / DT4 series User Manual 3. Operator panel 3-1. FEED button When you press the FEED button, the printer moves the label to the defined stop position. If you are using continuous labels, pressing the FEED button will move label stock until you release the button again. If you are using individual labels, pressing the FEED button will move only one label. If the label does

• Godex DT2, 26 DT2 / DT4 series User Manual 5. Accessories 5-1. Installing the label dispenser 1 Label dispenser 2 Screws (set of 2) 【 Note1 】 Remember to switch off the printer before installing the label dispenser. 【 Note 2 】 A label liner thickness of 0.006 mm ± 10% and a weight of 65 g/m 2 ± 6% are recommended. 【 Note3 】 The label dispenser will take labels up to a max. width of 110 mm (DT4) or 54 mm (DT2). 1. Place the printer on a flat surface and open the printer cover. 2. Remove the front cover.

• Godex DT2, 13 DT2 / DT4 series User Manual 2-4. Installing the driver 1. Insert the product CD in the CD/DVD drive of the host computer and open the "Windows Drivers" folder on the CD. 2. Execute the file with the same icon as the file selected in the illustration on the right. 3. Follow the instructions in the installation wizard. 4. Select "Install printer drivers" to start with the driver installation. 5. Specify your printer model and continue with the installation.

• 28 DT2 / DT4 series User Manual 10. Open the dispenser by folding it out. 11. Load the labels, following the instructions in Section 2-1. 12. Remove the first label and pass the label liner over the roller and the tear-off plate. 【 Note 】 The label stock should be at least 25 mm high. 【 Suggestion 】 When using the label dispenser,

• Godex DT2, 14 DT2 / DT4 series User Manual 6. Specify the port used to connect the printer to the host computer. 7. Enter a printer name. The printer will be listed under this name in the "Printers and Faxes" folder. 8. Specify whether or not you want to share the printer with other network users and assign the printer a share name. 9. When you have configured all the settings, a summary of the printer settings is displayed, which you should check. 10. If all settings are correct, click Finish to start copying the driver files. 11. Once copying is complete, the new printer

• Godex DT2, 16 DT2 / DT4 series User Manual 3-4. Self test The self-test function helps you find out whether the printer is functioning normally. The printer prints the following test page: 【 Note 】 For more information about advance settings, such as “Sensor switch” or “Dump Mode”, please refer to Programmer’s manual.

• Godex DT2, 2 DT2 / DT4 series User Manual Resident Fonts Bitmap fonts: 6, 8, 10, 12, 14, 18, 24, 30, 16X26 and OCR A & B Bitmap fonts 90°, 180°, 270° rotatable, single characters 90°, 180°, 270° rotatable Bitmap fonts 8 times expandable in horizontal and vertical directions Scalable fonts 90°, 180°, 270° rotatable Download Fonts Bitmap fonts 90°, 180°, 270° rotatable, single characters 90°, 180°, 270° rotatable Asian fonts 90°, 180°, 270° rotatable and 8 times expandable in

• Godex DT2, 5 DT2 / DT4 series User Manual Model DT4x Print Method Direct Thermal Resolution 203 dpi (8 dots/mm) Print Speed 7 IPS (177 mm/s) Print Width 4.25” (108 mm) Print Length Min. 0.16” (4 mm)** ; Max. 68” (1727 mm) Processor 32 Bit RISC CPU Memory 8MB Flash (4MB for user storage); 16MB SDRAM Sensor Type Adjustable reflective sensor. Fixed transmissive sensor, central aligned Media Types: Continuous form, gap labels, black mark sensing, and punched hole; label length set by auto sensing or programming. Width: 1” (25.4 mm) Min. - 4.64” (118 mm) Max. Thi

• Godex DT2, 7 DT2 / DT4 series User Manual 1-3. Getting to know your printer 1. LED indicator 2. FEED function button 3. Printer cover 4. On/off switch 5. Release buttons 1. Print head release lever 2. Label roll holder 3. Print mechanism 4. Label supply hub 5. Label guides 6. Front cover 2 4 1 5 3 1 2 3 6 5 4

• Godex DT2, 21 DT2 / DT4 series User Manual Alert Path Setting NetSetting will send the alert messages to designated mail account when the error happened on printer. The alert messages are sent by SMTP (Simple Mail Transfer Protocol) or SNMP (Simple Network Management Protocol). You can set or change the configurations of SMTP and SNMP on this “Alert Path Setting” tab. You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.

• Godex DT2, 23 DT2 / DT4 series User Manual Printer Configuration Set or change the configurations of connected printer. Most of key settings for the printer operation can be done by this setting page. You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.

• Godex DT2, 19 DT2 / DT4 series User Manual 4-2. The interface of NetSetting Click the NetSetting icon to start the program; you will see the start page as below. The start page will display the basic information of connected printer and your PC. Click the magnifier icon to search the Godex printers which are connected via Ethernet port in you network environment. Once a connected Godex printer is detected, it will be listed on the start page. There are six tabs on the top of interface which can configure different types of network setti

• 24 DT2 / DT4 series User Manual User Command The “User Command” tab provides a communication interface for operator to control the printer. Input printer commands in "Input Command" window and press “Send Command” button, the commands will be sent to the printer. For some commands that will return response message, the message will be di

• Godex DT2, 30 DT2 / DT4 series User Manual 3. Pass the cutter cable through the opening as shown in the illustration. 4. Fit the label cutter in the recess provided. DT4 DT2 5. Turn the printer upside down and tighten the screws to secure the cutter. 5. Turn the printer upside down and remove the screw that secures the cover on the bottom of the printer. 6. Open the cover on the bottom of the printer to access the motherboar d . 6. Tighten the screws to secure the label cutter. 7. Connect the cutter to the motherboard

• Godex DT2, 3 DT2 / DT4 series User Manual Model DT2x Print Method Direct Thermal Resolution 203 dpi (8 dot/mm) Print Speed 7 IPS (177 mm/s) Print Width 2.12” (54 mm) Print Length Min. 0.16” (4 mm)** ; Max. 68” (1727 mm) Processor 32 Bit RISC CPU Memory 4MB Flash (2MB for user storage) ; 16MB SDRAM Sensor Type Adjustable reflective sensor. Fixed transmissive sensor, central aligned Media Continuous form, black mark sensing, and punched hole; label length set by auto sensing or programming Width: 0.6” (15 mm) Min. - 2.36” (60 mm) Max. Thickness: 0.003” (0.06 mm) Min. -

More Instructions:

	Godex DT2 Operation & user’s manual 09-10-2022 39	DOWNLOAD
	Godex DT2 Operation & user’s manual 26-07-2023 35	DOWNLOAD

Related Products and Documents (Printer):

Comparable Devices:

Similar Resources:

• Atexco X (66 pages) Model X High Speed Sublimation printer 1 Model X High Speed Sublimation printer User manual Ver 1.0 Hangzhou Honghua Digital Technology Stock Co., Ltd. Address: 3911 Binsheng Road, Binjiang District, Hangzhou Postal Code (PC): 310052 TEL：+86-0571-88866678 FAX：+86-0571-88852900 E-Mail：[email protected] Website：w …

• Canon CR-206 (44 pages) 1更换步骤更换步骤交換手順書交換手順書Replacement ProcedureReplacement ProcedureProcédure de remplacementProcédure de remplacementErsetzenErsetzenProcedura di sostituzioneProcedura di sostituzioneProcedimiento de sustituciónProcedimiento de sustituciónProcedimento de substituiçãoProcedimento de substituição更換程序更換程序교 …

• Ricoh FW770 (92 pages) FW770Operating InstructionsZfbh010e.epsRead this manual carefully before you use this product and keep it handy for futurereference.For safety, please follow the instructions in this manual. …

• DataCard CE870 (130 pages) Datacard® CE870™ Instant Issuance SystemInstallation and Administrator’s GuideJanuary 2017Part No. 527263-001, Rev. H …

• Canon iP4500 - PIXMA Color Inkjet Printer (54 pages) iP4500 SIMPLIFIED SERVICE MANUAL 1. PRODUCT LIST 2. PRODUCT SPECIFICATIONS 3. ERROR DISPLAY 4. REPAIR 5. SERVICE MODE 6. SERVICE POLICY QY8-13BI-000 Rev. 00 July 12, 2007 Canon Inc. …

• Epson 84PLUS (9 pages) Message Broadcasting 1Message BroadcastingMessage Broadcasting is a plug-in for EasyMP Monitor. Administrators can use the plug-in to send messages or announcements to one or more projectors or all the projectors on the network. You can send messages manually, or use the Timer function in EasyMP Monitor to have messages sent automatically.You can use Message …

Comments, Questions and Opinions: