Manualios.com

Godex EZ-1105 Operation & User’s Manual

Godex EZ-1105 Manual Online:

3.3, 732 votes
Godex EZ-1105 User Manual
Godex EZ-1105 User Guide
Godex EZ-1105 Online Manual

Text of Godex EZ-1105 User Guide:

  • Godex EZ-1105, 1. BARCODE PRINTER................................................................... 5 1-1. Printer Accessories......................................................................................................... 5 1-2. General Specifications.................................................................................................... 5 1-3. Communication Interface................................................................................................ 7 1-4. Printer Parts....................................................

  • Godex EZ-1105, 1-4. Printer Parts 2 1 3 4 5 6 1. Cover Open Button 2. Top Cover 3. Label Roll Core 4. Ribbon Rewind Wheel 5. Print Mechanism 6. Ribbon Core Holder (rewind) 2 1 4 5 3 1. LED Light 2. FEED Key 3. Locking Tenon (left/right) 4. Ribbon Observing Window 5. Print Head Pressure Adjustment Screw (left/right) EZ-1105 / EZ-1305 User’s Manual 8

  • Godex EZ-1105, 2-2. Label Installation 1. Open the top cover by pressing the Cover Open Buttons on both sides. 2. Place the label roll onto the Label Roll Core. 3. Press the locking tenons and then lift up the Printing Mechanism. 4. Feed the label through the two Label Guides to the Tear-off Bar. 5. Align the Label Guides to the edge of label. 【 Note 】 When adjusting the Label Guides, please move both Label Guides together at the same time. 6. Close the Printing Mechanism to complete the label installation. E

  • Godex EZ-1105, Safety Instructions Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben. 1. Die Geräte nicht der Feuchtigkeit aussetzen. 2. Bevor Sie die Geräte ans Stromnetz anschließen, vergewissern Sie Sich, dass die Spannung des Geräts mit der Netzspannung übereinstimmt. 3. Nehmen Sie das Gerät bei Überspannungen (Gewitter) vom Netz. Das Gerät könnte sonst Schaden nehmen. 4. Sollte versehentlich Flüssigkeit in das Gerät gelangen, so ziehen sofort den Netzstecker. Anderenfalls besteht die Gefahr eines lebensgefährlichen elektrischen Schlags. 5. Wartungs- und Reparaturarbeiten dürfen aus Sicherheitsgründen nur von autorisier

  • Godex EZ-1105, 1-3. Communication Interface USB Interface Connector Type : Type B PIN NO. 1 2 3 4 FUNCTION VBUS D- D+ GND Serial Interface (Optional) Serial Default Setting : 9600 baud rate、no parity、8 data bits、1 stop bit、XON/XOFF protocol and RTS/CTS。 RS232 HOUSING (9-pin to 9-pin) DB9 SOCKET DB9 PLUG --- 1 1 +5V,max 500mA RXD 2 2 TXD TXD 3 3 RXD DTR 4 4 N/C GND 5 5 GND DSR 6 6 RTS RTS 7 7 CTS

  • Godex EZ-1105, FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operati

  • Godex EZ-1105, 3-4. Self-Test page The Self-Test page helps user to figure out whether the printer is operating normally. Below are some general descriptions about the content of Self-Test page: EZXXXX : VX.XXX Serial port :96,N,8,1 int-usb sw setting: ext-USB 1 DRAM installed Image buffer size : 1500K 000 FORM(S) IN MEMORY 000 GRAPHIC (S) IN MEMORY 000 FONT(S) IN MEMORY 000 ASIAN FONT(S) IN MEMORY 000 DATABASE(S) IN MEMORY 000 TTF(S) IN MEMORY 2048K BYTES FREE MEMORY ^S4 ^H10 ^R000 ~R200 ^W10 ^Q48,3 Option : ^D0 ^O0 ^AD Reflective Sensor Value: 42_48 Voltage: 1.50 2.30 3.1

  • 3. Printer Setting 3-1. FEED Key After pressing the FEED key, printer will feed the media (according to media type) to the specified stop position. When printing with continuous media, pressing the FEED key will feed the media out to a certain length. When printing with labels, the printer will feed one label each time the FEED key is pressed. If the label is no

  • Godex EZ-1105, 12. Align the Bottom Cover to the hooks and reassemble it. 13. Tighten bottom case screws to complete the installation. Note: After the Ethernet module installation is completed, please send the "^XSET,USBETHERNET,1" printer command to printer for activating the Ethernet connection function. Please mind that USB port will be deactivated once the Ethernet connection function is activated. EZ-1105 / EZ-1305 User’s Manual 25

  • Godex EZ-1105, Safety Instructions Please read the following instructions seriously. 1. Keep the equipment away from humidity. 2. Before you connect the equipment to the power outlet, please check the voltage of the power source. 3. Disconnect the equipment from the voltage of the power source to prevent possible transient over voltage damage. 4. Don’t pour any liquid to the equipment to avoid electrical shock. 5. ONLY qualified service personnel for safety reason should open equipment. 6. Don’t repair or adjust energized

  • Godex EZ-1105, 5. Feed the ribbon from the Ribbon Supply Shaft. 6. Wrap the ribbon around the Printing Mechanism and stick the ribbon onto the rewind ribbon roll. 7. Rotate the Ribbon Rewind Wheel to make the ribbon tight and smooth. 8. Firmly close the Printing Mechanism to complete the installation. EZ-1105 / EZ-1305 User’s Manual 11

  • Godex EZ-1105, 2-4. PC Connection 1. Please make sure the printer is powered off. 2. Plug the power cable into the power socket on the wall, and then connect the other end of the cable to printer's power socket. 3. Connect the cable to the USB port on the printer and on the PC. 4. Turn on the PC and the printer, and then the printer’s LED light will shine. 【 Note 】 Please make sure the power switch is off before plugging the power cable into the printer. EZ-1105 / EZ-1305 User’s Manual 14

  • 4 6 3 2 1 5 1. Thermal Print Head 2. Label Guide 3. Platen Roller 4. Print Line Adjustment Gear 5. Ribbon Core Holder (supply) 6. Label Sensor 1. Fan-Fold Label Insert 2. Power Switch 3. Power Socket 4. USB Port 5. Ethernet Socket (Optional) 6. Serial Port / RS-232 (Optional) * The communication ports may vary depending on product types. EZ-1105 / EZ-1305 User’s M

  • Code Pages CODEPAGE 437, 850, 851, 852, 855, 857, 860, 861, 862, 863, 865, 866, 869, 737 WINDOWS 1250, 1251, 1252, 1253, 1254, 1255 Unicode (UTF8, UTF16) Graphics Resident graphic file types are BMP and PCX, other graphic formats are downloadable from the software Interfaces USB port (default on) Control Panel One Tri-color LED: Power (Green, Orange and

  • Godex EZ-1105, 6. Select connection port. 7. Enter the printer name and set printer sharing option. 8. A description page of printer settings will be displayed after all settings are completed. 9. Check if all printer settings are correct and then press Finish to start copying driver files. 10. Wait for file copying finished and complete the installation. 11. After the driver installation is complete, there should be a new printer model on Windows "Printer and Faxes" setting. EZ-1105 / EZ-1305 User’s Manual 16

  • Godex EZ-1105, 4. Accessory 4-1. RS-232 Module Installation 1 Module Connection Wire 2 RS-232 module 3 Secure Screw 4 RS-232 Back Panel Note: Please make sure that anti-static precautions are adopted during the installation. 1. Make sure the power is off and the power cable is unplugged. Place the printer onto a smooth surface and flip the whole printer unit upside down. 2. Unscrew bottom case screws as indicated in figure. 3. Push the places as the arrow pointed in figure with both hands. Then move the B

  • Godex EZ-1105, 2-5. Driver Installation 1. Insert the product CD to your computer’s CD Drive and find the "Windows Drives" folder. 2. Select the icon of driver file and click it to start the installation. 3. Follow the instruction on screen to keep the installation going. Then the Driver Wizard utility should run automatically. 4. Select "Install printer drivers". 5. Select printer model. EZ-1105 / EZ-1305 User’s Manual 15

  • 5-4. Troubleshooting Problem Recommended Solution Power on the printer, but the LED does not light up ♦ Check the power connector LED light turns red (power/status) after printing stops ♦ Check for software setting or program command errors ♦ Replace with suitable label or ribbon ♦ Check if label or ribbon is all out ♦ Check if label is

  • Godex EZ-1105, 5. Maintenance and Adjustment 5-1. Thermal Print Head Cleaning Unclear printouts may be caused by dusty print head, ribbon stain or label liner glue. Therefore when printing, it’s necessary to keep the top cover closed. Also, check and prevent paper/label from being stained or dusty to ensure print quality and to prolong the print head life. Print head cleaning instructions are as follows: 1. Power-off the printer. 2. Open the top cover. 3. Take out the ribbon. 4. Open the print head by pressing the locking tenons. 5. If on the print head (see blue

  • Godex EZ-1105, 3-8. Error Messages When an error happened during printing process, different LED light messages will be displayed. Users can diagnose the error situation according to the LED light. Frequency Quickly blinking Slowly blinking Steady Color Red light Orange light LED Light Description Solution Unable to detect the media. Please perform the Auto Sensing again. Media Out Replace with new label roll or ribbon roll. Media Error Media Jam Possible causes: card tags or paper fall into the gap behind the platen roller, can’t find

  • Godex EZ-1105, 3-6. Sensor Switch There are two types of sensor in printer: Reflective Sensor and See-through Sensor. Users can set one of them as active sensor. By default, the sensor setting is set on Auto-mode. However, sometimes the sensor may not be able to detect the label gap on special label materials. Then it would be necessary to change the sensor setting to other sensor. For example, when printing on labels with thick liner, colored liner or back graphics, the see-through sensor would need to be enabled since the reflective sensor may not work correctly. To switch between different sensors, please do as follows: 1. Make sure that

  • Godex EZ-1105, 8. Use long-nose pliers to loosen and remove the hexagonal screws on both sides of RS-232 module. 9. Align the RS-232 module to the RS-232 port and plug into it. 10. Tighten the hexagonal screws to fix the RS-232 module. 11. Plug the other end of Module Connection Wire into the socket on mainboard. 12. Align the hole of mainboard to the pillar and then turn the mainboard back to original position. Push the mainboard downward slightly to fix the mainboard with the hooks. 13. Align the Bottom Cover to the hooks and reassemble it. 14. Tighten bottom case screws to complete the installation.

  • Godex EZ-1105, 1. Barcode Printer 1-1. Printer Accessories After unpacking, please check the accessories that come with the package, and store appropriately.  Barcode printer  Power cord  Switching Power  USB Cable  Empty Ribbon Roll  Label Roll Core  Label Stop Plate  Quick Start Guide  CD (includes label editing software QLabel IV / Manuals) 1-2. General Specifications Model EZ-1105 EZ-1305 Print Method Thermal Transfer / Direct Thermal Resolution 203 dpi (8 dot/mm) 300 dpi (12 dot/mm) Print Speed 4 IPS (100 mm/s) 3 IPS (76.2 mm/s) Print Width 4.25” (

  • Godex EZ-1105, 4-2. Ethernet Module Installation 1 Ethernet Cable 1.8M 2 Ethernet module 3 Module Connection Wire 4 Ethernet Back Panel 5 Secure Screw 6 Hex Threaded Stand-off 7 Hex Threaded Stand-off Screw Note: Please make sure that anti-static precautions are adopted during the installation. 1. Make sure the power is off and the power cable is unplugged. Place the printer onto a smooth surface and flip the whole printer unit upside down. 2. Unscrew 3 bottom case screws as indicated i

  • Godex EZ-1105, 5-3. Print Line Adjustment To get better printing balance and quality, use print head adjusting gear to adjust the contacting surface between print head and label. 1. When turning print head adjusting gear counter-clockwise (as arrow 1 shows), print line would move in the direction where arrow A shows. 2. When turning print head adjusting gear clockwise (as arrow 2 shows), print line would move in the direction where arrow B shows. A B 1 2 EZ-1105 / EZ-1305 User’s Manual 27

  • Godex EZ-1105, 2. Printer Installation This printer model has the following print modes: Thermal Transfer (TT) When printing, ribbon must be installed to transfer the print contents onto the media. Direct Thermal (DT) When printing, no ribbon is necessary; it only requires direct thermal media. Please check the specific print mode, and then go into the Setting Mode after power on the printer。 2-1. Ribbon Installation 1. Place the printer on a horizontal surface and open the top cover by pressing the Cover Open Buttons on both sides. 2. Install the r

  • Godex EZ-1105, 7. Lift up the mainboard. Align the Hex Threaded Stand-off and Hex Threaded Stand-off Screw to each other and tighten as the figure showed. 8. Align the Ethernet module to the Ethernet port and plug into it. 9. Tighten the secure screw to fix Ethernet module onto the main board. 10. Connect one end of Module Connection Wire to the main board and the other end to the Ethernet module. 11. Align the hole of Ethernet module to the pillar and then turn the mainboard back to original position. Push the mainboard downward slightly to fix the mainboard with the hooks. EZ-1105 / EZ-1305 User’s Manual 24

More Instructions:

DOWNLOAD

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Frigidaire TGF320DWC Use & care manual frigidaire/tgf320dwc-33Y.pdf 11 Jan 2023 16
2 Homelite UT09523 Troubleshooting tips homelite/ut09523-2RL.pdf 10 Feb 2024 2 1.72 Mb
3 Toa A-901A Supplementary manual toa/a-901a-R9V.pdf 14 Jan 2023 1 0.06 Mb
4 Siemens SINAMICS G120D Operating instructions manual siemens/sinamics-g120d-9CA.pdf 24 Feb 2023 302
5 Lenovo ThinkCentre M75e Operation & user’s manual lenovo/thinkcentre-m75e-M5A.pdf 19 Jun 2022 84
6 Mitsubishi FX2N-64CL-M Operation & user’s manual mitsubishi/fx2n-64cl-m-693.pdf 29 Jan 2024 3

Similar Resources:

  • Canon

    IX 4000

    (8 pages)
    INSTALLATION MANUAL ON CISS FOR PRINTER CANON IX 4000/IP 4200 1 Installation Manual on Continuous ink supply system (CISS) For printer Canon IX 4000/ IP 4200 Thank you for using the “INKSYSTEM” Continuous ink supply system. It is the best device for an inkjet printer, and it will definitely decrease your printing costs. B …
  • Ioline

    FlexJet

    (4 pages)
    114140 NE 200th St. Woodinville, WA 980721.425.398.8282www.ioline.comInstall Ribbon Cable 3C FJEKit for # 109519, Procedure P/N 110623 Rev 0Step 1: Wire cutters, Phillips screw driver, 9/64” hex driver, 6 nylon zip ties and a grounding wrist strap.Step 2: The ribbon cable. Should come with the 6 nylon cable zip ties to attach to the carriage. Step 5 …
  • Samsung

    ML-4050N

    (6 pages)
    SAP Compatibility for the Samsung ML-4050N Printer WHITE PAPER SAP Compatibility for the Samsung ML-4050N Printer Introduction This white paper describes the testing methods used to verify the compatibility of the Samsung ML-4050N printer with SAP. SAP is at the heart of most enterprise operations, and these operations want to print with confidence. S …
  • Canon

    9500 Series

    (2 pages)
    Start HereEasy Setup InstructionsseriesPhoto Printer1 Unpack the PrinterCarefullyremove all items from the box.Remove the tapes from the printer.NOTE:·Ittakes about an hour to complete the setup of theprinter.·A USB cable is necessary to connect the printerwith your computer.2Power CordPIXMA Pro9500 seriesPrint HeadDocumentation andSoftware KitPIXMA Pro950 …
  • Xerox

    DocuColor 5252

    (22 pages)
    Finishing Solutions Planning Guide Supported Printers: • Xerox DocuColor 2045 / 2060 / 5252 / 6060 / 7000 / 8000 Digital Color Press • Xerox DocuPrint 75 / 90 & DocuTech 75 / 90 • Xerox Nuvera 100 / 120 Digital Production System July 13, 2005 Rev. E Xerox Document Binder 120-D (DB120-D) …
  • Durst

    Rho 351R

    (4 pages)
    Rho 351RRoll-to-roll UV-Inkjet PrinterThe high colour density of 2.25 D and the ability to underprint white or use it as a spot colour, enables both the printing of coloured media and the production of photo-quality backlits. The printing of backlits is automated by the special backlit function which applies double the ink coverage in one printing operation. …

Comments, Questions and Opinions: