Manualios.com

Panasonic WJSX350 - MATRIX SWITCHER Operating Instructions Manual

  • WJSX350 - MATRIX SWITCHER Matrix Switcher
  • maK68Lu1FD6Ew
  • Operating Instructions Manual
  • PDF / Adobe Acrobat Reader
  • 68

Panasonic WJSX350 - MATRIX SWITCHER Manual Online:

3.25, 1797 votes
Panasonic WJSX350 - MATRIX SWITCHER User Manual
Panasonic WJSX350 - MATRIX SWITCHER User Guide
Panasonic WJSX350 - MATRIX SWITCHER Online Manual

Text of Panasonic WJSX350 - MATRIX SWITCHER User Guide:

  • Panasonic WJSX350 - MATRIX SWITCHER, -59- 3. Press the AUX 1/WIPER (AUX 2/DEF) OFF button, while SHIFT is in Off position (Indicator light off), to turn off the user’s auxiliary switch in the Receiver. 12. Control History Mode This function enables display of camera pictures that have previously been controlled on the selected moni- tor. Up to ten (10) spot and preset position controls can be memorized and displayed by simply pressing the HIS- TORY BACK or HISTORY FWD button. 1. Select the monitor whose history is to be displayed. Refer to Monitor Selection on page 50. 2. Press the HISTORY BA

  • Panasonic WJSX350 - MATRIX SWITCHER, -50- OPERATING PROCEDURES 321 654 987 FWDBACK CAM 0 MON SETESC HISTORY LOGIN 321 654 987 FWDBACK CAM 0 MON SETESC HISTORY Before starting the following procedures, all system components should be turned on. 1. Log-in 1. Turn on the power switches of all system compo- nents. 2. Select the registered Operator Number (up to 15) by pressing the Numeric buttons, then press the CAM (SET) button. The initial factory setting is 1. The LOGIN indicator blinks when the selected reg- istered number is correct. See page 39 for details on registering Passwo

  • Panasonic WJSX350 - MATRIX SWITCHER, -42- 5. RS485 CAM COM. (RS485 Camera Site Communication) This table is used to set the Communication Parameters between the RS485 Port installed in the Matrix Switcher and the Camera Site. Move the cursor to RS485 CAM COM. on the SYSTEM menu by moving the Joystick Controller, then press the CAM (SET) button to display the RS485 CAM COM. menu as shown below. 6. EXT TIMING (External Timing) This table permits the sequence dwell time on the selected monitor to be synchronized with the time lapse mode set in the associated Time Lapse VTR. Move the cursor to the EXT TIMING on the SYSTEM menu by moving the Joystick Controller, then press the CAM (S

  • Panasonic WJSX350 - MATRIX SWITCHER, -47- @ C A M – P O S I S E T @ @ @ S E T C - P M A X = 9 9 6 @ P A G E C O U N T = 1 0 0 @ P R O G. C L E A R = S E T C A M – P O S I S E T ( P A G E = 0 0 1 ) CAM PRE C – P CAM PRE C – P 0 1 0 1 0 0 1 0 1 6 3 0 0 6 0 1 0 2 0 0 2 0 1 6 4 0 0 7 0 1 0 3 0 0 3 0 2 0 1 0 0 8 0 1 0 5 0 0 4 0 2 0 2 0 0 9 0 1 0 6 0 0 5 0 2 0 3 0 1 0 3. Repeat the above procedure until the title for a selected camera is completed. 4. If a wrong character is selected, press the

  • Panasonic WJSX350 - MATRIX SWITCHER, MODEL AUTO-PAN RANDOM-1 RANDOM-2 WV-7220D *b *b *b WV-7225 *b *b *b WV-CSR400 Available Not available Not available WV-CSR600 Available Not available Not available WV-BSR300 Available Not available Not available -53- While the ALT indicator is on, selecting a Camera Position Number by pressing the Numeric buttons also activates the camera to move to the desired position. Note: To be able to use the above function, the Preset Position Number must be registered with the Camera Number. Refer to the Camera Position Set on page 47 for the registration procedures. 5-5. Pan/Tilt Control (Auto/Random Panning) The functions described below are available wit

  • Panasonic WJSX350 - MATRIX SWITCHER, -23- Note: Be sure to confirm the switch number before setting, as these switches are not arranged in numerical order on the board. The switch arrangement on the board, from right to left, is as follows: SW7 (Reset Out 1), SW9 (Reset Out 3), SW8 (Reset Out 2), SW10(Reset Out 4), SW11 (Reset Out 5), SW13 (Reset Out7), SW12 (Reset Out 6), and SW14(Reset Out 8). 6. After setting the switches, secure them by tighten- ing the screws shown above. ● Mounting in the Rack 1. Remove the four rubber feet by removing the four screws from the bottom of the Matrix Switcher. Cautions: • Do not block the ventilation opening or slots in the co

  • Panasonic WJSX350 - MATRIX SWITCHER, -1- CONTENTS PREFACE ................................................................................................................................................................................ 2 FEATURES .............................................................................................................................................................................. 2 PRECAUTIONS ....................................................................................................................................................................... 3 HOW TO USE THIS MANUAL .....................................................................

  • -38- O P E R A T O R L E V E L T A B L E R E G I S T R A T I O N L E V E L T A B L E ( 1 ) 1 2 3 S E T U P M E N U P R O G R A M • O P E R A T O R • •  S Y S T E M • • A L L R E S E T

  • The serial number of this product may be found on the left of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. The lightning flash with arrowhead sym- bol, within an equilateral triangle, is interned to alert the u

  • Panasonic WJSX350 - MATRIX SWITCHER, -57- 9-5. White Balance Mode 1. Select the desired monitor and camera. Refer to Monitor Selection and Camera Selection on pages 50 and 51. 2. Select 9 by pressing the Numeric button, then press the FUNCTION button to toggle the White Balance between ATW and AWC. Notes: The above function is available when the camera function 1 is assigned to [7][8][9]. 9-6. Back Light Compensation (BLC) Mode 1. Select the desired monitor and camera. Refer to Monitor Selection and Camera Selection on pages 50 and 51. 2. Select a number (1-9) to be assigned by pressing the Numeric button, then press the FUNCTION but- ton to togg

  • Panasonic WJSX350 - MATRIX SWITCHER, -52- LEFT RIGHT UP DOWN 3. If Pan/Tilt control needs fine adjustment, move the Joystick Controller while pressing the PAUSE but- ton. 5-2. Pan/Tilt Control (Preset Position Operation) The following function requires the use of a camera with preset panning capability, such as the Panasonic WV- CSR600 series. 1. Select the desired monitor and camera. Refer to Monitor Selection and Camera Selection on pages 50 and 51. 2. Select the preset number by pressing the Numeric buttons. 3. Press the PRESET POSI button to activate the camera to move to the preset position. 5. Pan/Tilt Control 5-1. Pan/Tilt Cont

  • -54- 6-2. Defroster Control 1. Select the desired monitor and camera. Refer to Monitor Selection and Camera Selection on pages 50 and 51. 2. Press the AUX 2/DEF ON button, while SHIFT is in On position (Indicator light On), to turn on the Housing Defroster. To turn off the Defroster, press the AUX 2/DEF OFF button while SHIFT is in On position (Indicator light On). 7

  • Panasonic WJSX350 - MATRIX SWITCHER, -56- 321 654 987 FWDBACK CAM 0 MON SETESC HISTORY 7.MAY.98 12:34:56 C32 M2 CU3 3RD FLOOR P64 T32 ROOM 306 FUNCTION 321 654 987 FWDBACK CAM 0 MON SETESC HISTORY 7.MAY.98 12:34:56 C32 M2 CU3 3RD FLOOR P64 T32 ROOB 306 FUNCTION 9. Camera Function Control The camera functions (Electronic Shutter, Electronic Sensitivity Up, ALC/MANUAL, AGC, White Balance, BLC, Site Alarm, Camera Power, Camera Preset Sequence, Refresh Position) can be remote controlled on the Switcher’s front panel. Control operation should be performed with the monitoring camera picture on the selected monitor. The following functions are available only when the specified cameras with the des

  • Panasonic WJSX350 - MATRIX SWITCHER, -45- 3. UP LOAD MODE This table is used to upload camera setup data from the Matrix Switcher’s memory to each camera. Move the cursor to UP LOAD MODE on the DATA LOAD menu by moving the Joystick Controller, then press the CAM (SET) button to display the UP LOAD MODE menu as shown below. D O W N L O A D S E L. M O D E C 0 1 • C 0 9 • C 1 7 • C 2 5 • C 0 2 • C 1 0 • C 1 8 • C 2 6 • C 0 3 • C 1 1 • C 1 9 • C 2 7 • C 0 4 • C 1 2 • C 2 0

  • Panasonic WJSX350 - MATRIX SWITCHER, -39- Cautions: • To prevent unauthorized access, be sure to change the Password preset at the factory. • If an operator's level for access to the item “SETUP MENU” or “OPERATOR” on the LEVEL TABLE has not been registered, that operator will not be allowed access to the SETUP MENU a second time. 5. Move the cursor to the OPERATOR parameter by moving the Joystick Controller, then press the CAM (SET) button to display the table for the selected operator shown below. R E G I S T R A T I O N O P E R A T O

  • Panasonic WJSX350 - MATRIX SWITCHER, -3- • Refer all work related to the installation of this product to qualified service personnel or system installers. • Do not block the ventilation opening or slots on the cover. To prevent the appliance from overheating, place the appliance at least 5 cm (2 inches) away from the wall. • Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the power off immediately and contact quali- fied service personnel for service. • Do not attempt to disassemble the appliance. To prevent electric s

  • Panasonic WJSX350 - MATRIX SWITCHER, -12- 9-1. Level Setting Operator access to various setup functions and system operations is determined by the operator's level. There are three (3) separate levels available (Level 1 is the highest). 9-2. Priority Setting When two or more operators attempt to perform the same function at the same time, the operator with the highest priority is allowed to perform the function while the lower priority operators’ attempts are denied. There are eight (8) priority levels available in this sys- tem. 9-3. Password All operators have a five digit long password assigned to them. 9-4. Operator Limits

  • Panasonic WJSX350 - MATRIX SWITCHER, -6- FEATURES OF THE MATRIX SWITCHER Shown below is an example of a basic system of the WJ-SX350 Matrix Switcher. LOGIN BUSY PROHIBITED STATUS ALARM ALARM SEQUENCE ACK/RESET OPERATE ALL RESET RECALL CAM MENU SET UP PAUSE BACK SEQ FWD SEQ −1 CAM DEC DEC +1 CAM INC 321 654 987 FWD ALT SHIFT AUTO FOCUS FUNCTION ON OFF PRESET POSI CAM POSI BACK CAM 0 MON SETESC HISTORY AUTO PAN RANDM PAN AUX 1 WIPER AUX 2 DEF IRIS CLOSE NEAR FAR OPEN IRIS RESET FOCUS TELE WIDE LEFT UP DOWN ZOOM MATRIX SWITCHER WJ-SX350 CAMERA SITE CONTROL Video Data RS-485 Up to 32 Cameras 32-Alarm Input System Controller (M

  • Panasonic WJSX350 - MATRIX SWITCHER, -41- P C C O M. B A U D R A T E 1 9 2 0 0 D A T A B I T 8 P A R I T Y C H E C K N O N E S T O P B I T 1 X O N / X O F F O F F W A I T T I M E O F F C A M P O R T S E L E C T CAM CAM CAM CAM 0 1 1 0 9 2 1 7 1 2 5 2 0 2 1 1 0 2 1 8 1 2 6 2 0 3 1 1 1 2 1 9 2 2 7 2 0 4 1 1 2 2 2 0 1 2 8 2

  • -64- General Power Supply: 220 - 240 V AC 50 Hz Power Consumption: 45 W Max. Number of Camera Inputs: 32 Max. Number of Monitor Outputs: 8 Max. Number of Alarm Inputs: 32 (37-pin D-Sub Connector) Max. Number of Alarm Outputs: 8 (25-pin D-Sub Connector) x2 Max. Number of System Controllers: 4 (WV-CU350) RS-232C Port: 9-pin D-Sub Connector RS-485 Terminal: Half Duplex (A,

  • -34- 4. ALARM EVENT Select ALARM EVENT from the PROGRAM MENU, then press the CAM (SET) button. The ALARM EVENT menu appears on the monitor. As shown below, the ALARM EVENT menu allows access to five items: MODE SELECT, MODE (1,2,3) SETUP and MODE SCHEDULE. To select an item from the ALARM EVENT menu: 1. Move the cursor to the desired item by moving the Joystick Controller. 2. Press

  • Panasonic WJSX350 - MATRIX SWITCHER, -31- 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 T – S E Q N O. 0 1 ( S T E P = 2 5 – 3 2 ) < < S T E P = 2 5 2 6 2 7 2 8 > > C A M 2 5 2 6 2 7 2 8 P R E ( A U X ) 0 1 – – 0 2 – – D W E L L 0 3 0 2 0 1 0 5 < < S T E P = 2 9 3 0 3 1 3 2 > > C A M 2 9 3 0 3 1 3 2 P R E ( A U X ) – – 0 2 0 5 – – D W E L L 0 3 0 2 0 1 0 5 3. Move th

  • Panasonic WJSX350 - MATRIX SWITCHER, -48- F U N C T I O N K E Y M O D E F 1 – F 3 : S H U T T E R F 4 – F 6 : C A M F U N C T I O N 1 F 7 – F 8 : R C V F U N C T I O N F 1 : S H U T T E R O N / O F F F 2 : S H U T T E R D E C F 3 : S H U T T E R I N C ■ FUNCTION KEY MODE This table is used to programme and edit the camera functions by assigning a 1-digit number to each func- tion. The function can then be called up by simply pressing the respective Nume

  • Panasonic WJSX350 - MATRIX SWITCHER, -35- 1. Move the cursor to the ALARM MODE parameter by moving the Joystick Controller, then select the desired alarm mode by pressing the +1CAM INC or –1CAM DEC button. 2. Move the cursor to the INPUT SITE parameter by moving the Joystick Controller, then select Camera Site Alarm input On or Off by pressing the +1CAM INC or –1CAM DEC button. 3. Move the cursor to the INPUT BOARD parameter by moving the Joystick Controller, then select Interface Alarm input On or Off by pressing the +1CAM INC or –1CAM DEC

  • Panasonic WJSX350 - MATRIX SWITCHER, -8- Note: The desired camera selection may not be avail- able due to one of the following reasons: 1. The operator is not allowed access to the desired camera because the Operator Registration has lim- ited the operator's access to certain cameras. At this time PROHIBITED Indicator light up. See page 11 for more details. 2. The desired camera is currently selected by anoth- er operator who has a higher operator priority, and therefore, control over that camera. In this case, the BUSY Indicator lights up. 3. Camera Control The selected camera (if applicable) can be contr

Related Products and Documents (Matrix Switcher):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Panasonic KX-TCD515NL Operating instructions manual panasonic/kx-tcd515nl-13W.pdf 29 Nov 2023 102 4.67 Mb
2 Kyocera KM-1530 Instruction handbook manual kyocera/km-1530-1R1.pdf 17 Feb 2024 86
3 Peavey Ecoustic Operation & user’s manual peavey/ecoustic-8F8.pdf 08 Apr 2023 8 0.83 Mb
4 Zenith D60WLCD - 60" LCD Projection HDTV-Ready TV Installation and operating manual, warranty zenith/d60wlcd-60-lcd-projection-hdtv-ready-tv-13B.pdf 14 Feb 2023 60 1.39 Mb
5 LG 8575 Manual del propietario lg/8575-14D.pdf 26 Aug 2022 199
6 ASROCK H81M Operation & user’s manual asrock/h81m-Z4L.pdf 08 Dec 2023 87 20.57 Mb

Similar Resources:

  • Kramer

    88DEE

    (2 pages)
    © www.kramerelectronics.com 2008 LASSEN 88DEE 8x8 LASSEN SDI™ 8 SERIES ROUTING SWITCHERS LASSEN SDI 88 SERIES SERIES SDI VIDEO WITH 2 CHANNELS OF AES AUDIO. DESCRIPTION The Lassen 8 series are high performance routing switchers for SDI (SMPTE 259) and HD-SDI (SMPTE 292) video signals. These units come in a compact 2U (3.5”) frame and can be ordered …
  • AVGear

    AVG-UHMS88

    (31 pages)
    AVG-UHMS88 Features  Supports HDMI 1.4, 4Kx2K& 1080p 3D  HDCP1.4 compatible, supports manual HDCP management and auto-detection  Transmits 4Kx2K signal for 8m via the HDMI port, 40m via HDBT port  Audio source selectable via RS232 command  8 HDBaseT outputs, for transmission up to 70m at 1080p and 40m at 4Kx2K on a single CAT5e/6 …
  • Kramer

    VP-778

    (4 pages)
    VP-778 Quick Start (P/N: 2900-300445QS REV 1) P/N: 2900- 300445QS Rev: 1 Scan for full manual VP-778 Quick Start Guide This guide helps you install and use your VP-778 for the first time. Go to www.kramerav.com/downloads/VP-778 to download the latest user manual and check if firmware upgrades are available. Step 1: Check what’s in the box VP-778 Pr …
  • foxunhd

    FX-MX48IR-70

    (14 pages)
    Operating Instructionswww.foxunhd.comFX-MX48IR-70HDMI Matrix&4x4Group(HDMI&HDBaseT)Dear CustomerThank you for purchasing this product. For optimum performance and safety, please read theseinstructions carefully before connecting, operating or adjusting this product. Please keep this manual forfuture reference.ABLE OF CONTENTSFeatureSpecificationsPack …
  • KVM-TEC

    Smartline SVX1

    (8 pages)
    KVM-TEC SVX1 Ver. 1.4 kvm-tec electronic gmbh – 2522 Oberwaltersdorf – Kulturstrasse 1 – Austria Tel +43-2253 / 81912 – Fax +43 2253 819 12 99 – Email [email protected] - 1 www.kvm-te c.com Art.Nr: 6501 Smartline SVX1 …
  • Shinybow USA

    SB-4144TB

    (15 pages)
    INSTRUCTION MANUAL MODEL : SB-4144TB4X4 VGA-Audio Matrix Switcher VGA-Audio Matrix Switcher VGA-Audio Matrix Switcher SeriesThank you for purchasing the SB-4144TB VGA-Audio Matrix Switcher. You will fi nd this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this switcher.MULTIMEDIA …

Comments, Questions and Opinions: