Manualios.com

Panasonic KXHGC200 - PCMCIA WIRELESS LAN Operating Instructions Manual

  • KXHGC200 - PCMCIA WIRELESS LAN Network Hardware
  • maK68Lu1FD6Ew
  • Operating Instructions Manual
  • PDF / Adobe Acrobat Reader
  • 80

Panasonic KXHGC200 - PCMCIA WIRELESS LAN Manual Online:

4.6, 946 votes
Panasonic KXHGC200 - PCMCIA WIRELESS LAN User Manual
Panasonic KXHGC200 - PCMCIA WIRELESS LAN User Guide
Panasonic KXHGC200 - PCMCIA WIRELESS LAN Online Manual

Text of Panasonic KXHGC200 - PCMCIA WIRELESS LAN User Guide:

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 69 For assistance, please call: 1-800-272-7033 Appendix Troubleshooting “ Problem When you insert KX-HGC200 to the PC card slot, the Install wizard screen is not displayed. The computer does not operate even if you insert KX-HGC200. You cannot install the KX-HGC200 device driver. The Network management web screen is not displayed. You cannot connect with the computer. You cannot connect with the Broadband Networking Gateway. Remedy ≥ The KX-HGC200 may not be inserted properly. Insert it again firmly to the end. ≥ The PC card socket may not be working properly. After checking its operation, insert

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 62 “ Using the Device Management Dialog Box Changing the channel (radio frequency) The KX-HGC200 is preset to communicate using the radio frequency channel 6 (2437 MHz). This preset channel can be changed to channel 1 (2412 MHz) or 11 (2462 MHz) by using the Channel Number pull-down menu. To communicate, all the nodes in a wireless network must be set the same radio frequency channel. Setting a computer to the Master Node The KX-HGC200 is preset to automatically assign a Master Node (p. 73) t

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 78 Index A Add A New Node . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Add New Hardware Wizard . . . . . . . . . . . . . . . . . . .29 Arrow mark . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 27 B Bandwidth Information . . . . . . . . . . . . . . . . . . . . . . .57 Broadband Networking Gateway . . . . . . . . . .6, 13, 15, 19, 22, 46, 64 Broadband Networking Gateway administration web screen . . . . . . . . . . . . . . . .13, 17 Broadband Networking Gateway firmware . . . . . .7, 14 C

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 51 For assistance, please call: 1-800-272-7033 Installation 7 Click [OK]. 8 Click [Yes] to restart the computer. ≥The computer restarts. The network protocol has been set up and now that all the installation steps for using the KX-HGC200 have been completed. To maintain your wireless network, the Network Manager software is available. For more details, refer to p. 54. While a computer is restarting, mind below notification. ≥If the KX-HGC200 has been installed to a computer, restarting may take about a few minutes. ≥To prevent a device from being damaged or broken, never turn off a computer while restarting. PQQX12925ZA 01.2.27 3:56 PM ページ 51

  • For product service ≥Panasonic Servicenters are listed in the servicenter directory. ≥Call 1-800-272-7033 for the location of an authorized servicenter. ≥After the limited warranty, please contact our Continued Services Technical Support Line at 1-900-555-PANA (1-900-555-7262). If you have difficulty reaching this number, it may be blocked by your phone company. Please contact yo

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, For Best Performance 3 For assistance, please call: 1-800-272-7033 Location of the units Communications are transmitted between the KX-HGC200s using wireless radio waves at 11Mbps data speed. For maximum performance, it is recommended that the KX-HGC200 be operated: ≥Metal or steel framework, such as refrigerators, can hinder radio communications. Open areas offer better performance. ≥If the KX-HGC200 is located near a microwave oven which is in use, communication may be interfered with. For maximum performance, operate the KX-HGC200 away from microwave ovens. ≥It is recommended that the KX-HGC200s be loca

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 26 “ Installing the KX-HGC200 to a Computer 4 In the PCMCIA socket list, confirm ? mark or ! mark is not followed by the PCMCIA socket. ≥If ? mark or ! mark is followed, device driver of the PC card socket is not properly installed. Refer to the manual of your computer and re-install the proper device driver first, then insert the KX-HGC200. 5 Click [Close]. 6 Click [OK] to close the window. To save the boot up time when the Ethernet adapter is attached or equipped to your computer If the Ethernet adapter that is attached or equipped to your computer works with the KX-HGC200 at the same time,

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, “ Setting up the Broadband Networking Gateway 22 Caution when initializing the Broadband Networking Gateway When the CLEAR SETTING button on the Broadband Networking Gateway is pressed, all the parameters that have been set to the Broadband Networking Gateway reset to the default setting. If the KX-HGC200 is inserted and the WIRELESS indicator of the Broadband Networking Gateway is turning green at that time, all the parameters (Node Name, Channel Number, FEC, Network Name and Network ID) reset to default settings also. If you want to preserve the parameters set to the KX-HGC200, first remove the KX-HGC200 from the Broadband Networking Gateway referring to “Removing the KX-HGC

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 77 For assistance, please call: 1-800-272-7033 Appendix ≥Environment—do not place the unit in a room where the temperature is less than 5oC (41oF) or greater than 35oC (95oF). Allow 10 cm (4q) clearance around the unit for proper ventilation. Avoid excessive smoke, dust, mechanical vibration, shock, or direct sunlight. ≥Medical—consult the manufacturer of any personal medical devices, such as pacemakers, to determine if they are adequately shielded from external RF (radio frequency) energy. (The unit operates in the frequency range of 2400MHz to 2483.5MHz and the power output level is 0.1 watt.) Do not use the unit in health care facilities if any reg

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 76 FCC and Other Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 9 Before Start For assistance, please call: 1-800-272-7033 Part Names Part names Indicators Panasonic Panasonic KX-HGC200 READY LINK PCMCIA Connector with 68 pins Arrow mark (p. 15, 27) LINK indicator READY indicator Note: ≥To prevent the KX-HGC200 from being damaged, never touch the PCMCIA connector. LED LINK READY Status Green Green (Blinking) Off Green Indicates ≥The KX-HGC200 is turned on and transmitting/receiving data to/from another KX-HGC200. ≥The KX-HGC200 is turned on and transmitting/receiving data to/from another KX-HGC200, but the data transmission status is not stable. ≥The KX-HGC200

  • 13 For assistance, please call: 1-800-272-7033 Installation Installing the KX-HGC200 in the Broadband Networking Gateway “ Confirming the Broadband Networking Gateway firmware version Depending on the firmware version of the Broadband Networking Gateway, it may not support the KX-HGC200. Before adding the Broadband Networking Gateway to your wireless network, ch

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 41 For assistance, please call: 1-800-272-7033 Installation “ The Network Manager software has been successfully installed. To add more computers to the wireless network, refer to pages from 25 and perform the installation of the computer. After the software has been installed, the Network Manager icon is located in the taskbar and shortcut leading to it is located on your desktop. Refer to p. 54 for more details about the Network Manager software. Shortcut to the Network Manager Network Manager icon in the taskbar (See below.) Icon Status The KX-HGC200 has not been inserted into t

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 2 Before Initial Use Thank you for purchasing the Panasonic 11 Mbps Wireless LAN PC Card. For your future reference Serial No. Date of purchase (found on the rear side of the unit) Name and address of dealer FOR OPERATION ASSISTANCE: –Call 1-800-272-7033 –Refer to the Panasonic world wide web site http://www.panasonic.com ≥Microsoft, Windows and Netmeeting are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. ≥Ethernet is a registered trademark of Xerox Corporation. ≥Whitecap™ is a trademark of ShareWave™, Inc. ≥Screen shots reprinted with permission from Microsoft Corporation. All other bra

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 23 For assistance, please call: 1-800-272-7033 Installation “ Helpful functions For checking the setup parameters or data-transmission status of the KX-HGC200, helpful functions are available on the Broadband Networking Gateway administration web screen. Checking the setup parameters 1 Click [Status] on the Broadband Networking Gateway administration web screen. 2 Check the Wireless section. Firmware Version Network ID (p. 10) Master Node IP Address (p. 73) Wireless Card State Current version of the firmware, written in the KX-HGC200 Flash

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, “ Installing the KX-HGC200 in the Broadband Networking Gateway 16 4 Turn on the Broadband Networking Gateway and other devices that are being used with it. ≥Make sure the READY indicator of the KX-HGC200 (p. 9) and the WIRELESS indicator of the Broadband Networking Gateway are lit. If not lit, refer to p. 13 and confirm the Broadband Networking Gateway firmware version. 5 Close the cover of the Broadband Networking Gateway. INTERNET ETHERNET HomePNA POWER KX-HGW200 WIRELESS LINK READY 11M p Wireless LAN PC Card KX-HGC200 WIRELESS indicator READY indicator LINK READY 11Mbp Wireless LAN PC Card KX-HGC200 PQQX12925ZA 01.2

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, “ 71 For assistance, please call: 1-800-272-7033 Appendix Problem You cannot share files and/or the printers. You cannot access the Internet. (When using the Broadband Networking Gateway) Remedy ≥ Check the LINK indicator of KX-HGC200. When the LINK indicator is turned off, the computer is not connected to the network. Check the connecting condition of the computer referring to the case of “You cannot connect with the computer.” (p. 69, 70). ≥ When the LINK indicator is turned on, check the following settings. ≥Computer which setting? ≥Sharing of files how? ≥Sharing of printers how? ≥ You may have not entered the password when starting up the Window

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, Installation Overview 10 4 important parameters to create a wireless network A wireless network can be created using the 4 parameters below which are programmed in the Flash-ROM of the KX-HGC200 or in a node*. Normally, you would only program the Network Name because the other parameters have been already set. However, for later customization, be sure to read about the parameters below. *Node: A device that is connected to the network and can communicate with other network devices. In this Operating Instructions, we use this word for the Broadband Networking Gateway or a c

  • 47 For assistance, please call: 1-800-272-7033 Installation “ 3 Select TCP/IP->Panasonic 11Mbps Wireless LAN PC Card and click [Properties]. 4 If the DHCP server function of the Broadband Networking Gateway is being used, click the IP Address tab and select Obtain an IP address automatically and click [OK]. Unless the DHCP server function of the Broadband Networking Gateway

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, “ 11 Before Start For assistance, please call: 1-800-272-7033 Network with the Broadband Networking Gateway KX-HGW100 HomePNA WIRELESS ETHERNET INTERNET POWER Internet Broadband Networking Gateway Cable/xDSL Modem KX-HGC200 KX-HGC200 KX-HGC200 Inserting the KX-HGC200 in the Broadband Networking Gateway (p. 15) Setting up from a wired computer (p. 17) Setting up from a wireless computer (p. 19) Inserting the KX-HGC200 into a computer (p. 27) Installing the device driver (p. 29) Installing the Network Manager (p. 38) Setting an IP address (p. 46) Requ

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 67 For assistance, please call: 1-800-272-7033 Appendix Uninstalling the KX-HGC200 Software “ The steps for uninstalling the KX-HGC200 software are performed using the uninstall software which was installed during the installation of the KX-HGC200 device driver. 1 Make sure the KX-HGC200 is not inserted in the PC card slot of the computer. 2 From the Start menu, point to Programs, point to Panasonic Wireless PC Card and click Uninstall. PQQX12925ZA 01.2.27 3:56 PM ページ 67

  • 39 For assistance, please call: 1-800-272-7033 Installation “ 3 Click [Next]. ≥If you want to specify a directory, clicking [Browse] will help you. ≥The Network Manager software will be installed to your computer. PQQX12925ZA 01.2.27 3:56 PM ページ 39

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 38 “ Installing the KX-HGC200 to a Computer Installing the Network Manager After the device driver has been installed to a computer, the computer restarts and the installation of the Network Manager software starts automatically. 1 Click [Next] and start the setup. ≥The Software License Agreement dialog box appears. 2 Click [Yes] after you have read all the contents and if you agree with the end user agreement on the dialog box. PQQX12925ZA 01.2.27 3:56 PM ページ 38

  • Panasonic KXHGC200 - PCMCIA WIRELESS LAN, 61 For assistance, please call: 1-800-272-7033 Network Manager Creating a new wireless network/ Joining another wireless network 1 Click [Change...] in the Change Network Name section. 2 Enter the name of the network to which you are moving and click [OK]. ≥The data setting field is not case-sensitive. ≥If you are creating a new wireless network near an existing wireless network, to prevent the radio frequency interference, be sure to set a different channel number (p. 62) from the existing network. 3 Click [OK]. “ About the network name To communicate with others in a wireless group, the same Network Name must be programmed into each computer. It is impossible to communicate with

  • 60 “ Using the Device Management Dialog Box Configuration tab Configuration tab allows you to use the following functions: Firmware Update* Change Network Name (p. 61) Modify Settings (p. 62) *Not available in current release. To modify the current settings of the wireless networking status: First, change each group of settings following the instructions on p. 62. To make new settin

Related Products and Documents (Network Hardware):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Sonoro MEISTERSTÜCK SO-610 Operating manual sonoro/meisterstuck-so-610-974.pdf 28 Sep 2022 334
2 Fanimation FP4820PW The Cumulos Owner's manual fanimation/fp4820pw-the-cumulos-82F.pdf 23 Aug 2023 31
3 GE Eterna EGR3001EPSS Specifications ge/eterna-egr3001epss-PWI.pdf 03 Jan 2024 2 0.37 Mb
4 Electro-Voice ZX Series ZX5-60PI Technical specifications electro-voice/zx-series-zx5-60pi-KX6.pdf 03 Jul 2022 4 0.55 Mb
5 Olympus VN 7000 Instructions olympus/vn-7000-P79.pdf 01 Apr 2023 2
6 Jenn-Air W10204447A Use and care manual jenn-air/w10204447a-DV5.pdf 15 Mar 2023 20

Similar Resources:

  • ICP DAS USA

    I-8431

    (8 pages)
    Copyright © 2011 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected] I-8431/I-8831/I-8431-80/I-8831-80 Quick Start Guide 1 Quick Start Guide for I-8431/I-8831/I-8431-80/I-8831-80 January 2011, Version 1.1 Congratulations on purchasing 8000 series PAC, I-8431/I-8831/I-8431-80/I-8831-80 - the most popular automation solution for remote moni …
  • OpenVox

    X204 Series

    (37 pages)
    X204 hybrid telephony card User Manual 1 OpenVox Communication Co. LTD. URL: www.openvox.cn OpenVox Communication Co.Ltd X204 Series User Manual Version: 1.0 …
  • Fortinet

    FortiGate FortiGate-1000A

    (2 pages)
    USBA2A1CONSOLEFront1 to 10InterfaceLCDControlButtonsRemoteManagementModem PortFiber-opticPorts A1 and A2(FortiGate-1000AFA2 only)Serial PortUSB (future)Power CableRack-Mount BracketsEthernet Cables:Orange - CrossoverGrey - Straight-throughDocumentationFortiGate-1000A / 1000AFA2QuickStart GuideCopyright 2005 Fortinet Incorporated. All rights reserved.Trademar …
  • Huawei

    OptiX RTN 910A

    (26 pages)
    HUAWEI TECHNOLOGIES CO., LTD.OptiX RTN 910A Radio Transmission System V100R010IDU Quick Installation Guide for Outdoor Cabinets(OMB Cabinets)Issue: 01Date: 2017-05-30 …
  • H3C

    H3C S7500E-X

    (290 pages)
    H3C S7500E-X Switch SeriesLayer 2 - LAN SwitchingConfiguration Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: S7500EX-CMW710-R7178 Document version: 6W100-20160118 …
  • Avaya

    VSP 8284XSQ-AC

    (2 pages)
    2Unpack the equipment and verify package contentConfirm that you have the following tools and cables: • Phillips #2 screwdriver • RJ-45 console port cable • ESD cableVirtual Services Platform8000 SeriesQuick Install GuideAvaya1. Avaya Virtual Services Platform (VSP) 8000 Series switch2. Rack-mounting hardware that includes: a. Rack-mount …

Comments, Questions and Opinions: