Grundig HDTV 1000 T Assembly Instructions Manual

Text of Grundig HDTV 1000 T User Guide:

• Grundig HDTV 1000 T, - 39 - - 39 - Guard interval In this menu item you set the relation of the duration of the user symbols to the duration of the guard intervals to be transmitted. A high guard interval, e.g. “G1/4” causes a low output data rate. For cable networks the setting “G1/32” is adequate. • Use the ▶ ◀ / buttons to place the cursor under “ G… ”. • Set the guard interval required using the buttons (“G1/4”, “G1/8”, “G1/16”, “G1/32”). • Press the button. —> The “Setting the transmitter identification” – “COFDM TPS” menu is activated. Setting the transmit

• Grundig HDTV 1000 T, - 42 - - 42 - Network Information Table (NIT) • To switch NIT on/off (“on”/ ”off”) press the buttons. • Press the ▶ button to activate NIT (“Make”). —> All active …- COFDM cassettes must be set and ready for reception. —> The NIT of all …- COFDM cassettes are switched on. —> The cassette fetches all the information (output fre- quencies, output data rates, etc.) it needs from all the …- COFDM cassettes in order to generate the NIT. This process may take a few seconds. Then the NIT is generated, added and sent to all �

• Grundig HDTV 1000 T, - 21 - - 21 - • If you do not want to do ASI settings, press the button. —> The “Selecting the channel strip” – “LINE” menu is activated (page 23). • To set the ASI parameters press the button. —> The “Setting the ASI transfer rate” – “ASI RATE” menu is activated. Setting the ASI transfer rate In this menu you set the output transfer rate for the ASI com- ponent connected. For this setting please take the required information from the documentation (technical data) of the ASI component to be connected. • Use the ▶ ◀ / buttons to place the cursor under the digits to be set for the transfer rate then use the but

• Grundig HDTV 1000 T, - 49 - - 49 - Further possible terms displayed: “ RA ” – Radio channel type “0” – The currently selected station is encrypted. • Use the ▶ ◀ / buttons to call up the stations in sequential order which are to be decoded, then use to decrypt (“X”) or not to decrypt them (“0”). • Save changes and activate the station filter: Press the button. —> The filter is activated. The display shows the “Configuring the CA module” – “CA” menu. • Press the button. —> The “Setting the

• Grundig HDTV 1000 T, - 20 - - 20 - Selecting the input signal path In this menu you define the signal path of the input transport streams. Menu setting “A+ASI = 1 B+ASI = 2” (s. chap. 2.4.1.1, page 6). Menu setting “A+B+ASI = 1 ASI = 2” (s. chap. 2.4.1.2, page 7). • Use the buttons to select the signal path wished. • Press the button. —> The “Selecting the output signal path” – “OUTROUTE” menu is activated. Selecting the output signal path In this menu you define the signal path of the output transport streams. Menu setting “ASI => ASI” (s. chap. 2.4.2.1, page 7). Menu setting �

• Grundig HDTV 1000 T, - 48 - - 48 - • Use the buttons to select the function desired. • To set the CA module use the ▶ ◀ / and buttons. • All settings are saved by pressing the M button. —> You will be returned to the “Configuring the CA module” – “CA” menu item. —> By pressing the button you can cancel the settings in the menu of the CA module and are re- turned to the “Configuring the CA module” – “CA” menu. • Press the ▶ button. —> The “Setting the station filter” – “Edit” menu is acti- vated. Setting the station filter In this menu you select the stations wished from the encoded data stream, wh

• Grundig HDTV 1000 T, Grundig SAT SystEms GSS Grundig SAT Systems GmbH Beuthener Strasse 43 D-90471 Nuremberg Phone: +49 (0) 911 / 703 8877 Fax: +49 (0) 911 / 703 9210 E-mail: [email protected] Internet: http://www.gss.tv Assembly Instructions Assembly Instructions English A A CLASS CLASS KLASSE KLASSE HDTV 1000 T Head-End Digital Modulator HDTV / COFDM

• Grundig HDTV 1000 T, - 30 - - 30 - Setting the station filter The default setting for the station filter is “off”. In this menu you define the stations received to be transmitted. If stations are activated the output data rate increases. If the station filter is switched off (factory default) all stations of the transport stream passes the station filter. As soon as the station filter is activated all stations are inactive and can be added to the transport stream selectively. The figure of the menu below is dependent on the setting of the “Selecting the input signal path” menu (page 20). The menu shows the setting ”A+B+ASI = 1 ASI = 2”. With this setting t

• - 17 - - 17 - Bx 4A 8k C7/8 COFDM-MODE G1/32 ▶ ◀ / 2 … 8k C1/2 … C7/8 G1/4 … G 1/32 Bx 4A CELL 0x0000 COFDM TPS off ▶ ◀ / 0x0000 … 0xFFFF on / off  M  Bx 4A 34363 (32502) STUFFING Bx 4A Null Packets FAILURE Null Packets … Single Carrier Bx 4A off NIT => Make ▶ on / off Make Bx 4A PID 0x0000 DROP off Bx 4A 0xDE00 CAT-ID off ▶ ◀

• - 25 - - 25 - • Use the ▶ ◀ / buttons to place the cursor under the digit to be set for the frequency display then use to set the output frequency wished. Switching the modulator off or on • To switch off the modulator place the cursor under “on” using the ▶ button and switch “off” the modulator of the channel strip using the buttons. �

• Grundig HDTV 1000 T, - 23 - - 23 - Selecting the channel strip • By pressing ◀ select channel strip “A” (“Line A”) or select channel strip “B” (“Line B”) by pressing the ▶ button . —> The “Selecting channel / frequency setting” – “OUTPUT” menu is activated. Selecting channel / frequency setting In this menu, you can choose the channel or frequen cy set- ting for the adjustment of the HF output. The channel setting covers the range of channels C5 … C12 and C21 … C69, the frequency setting covers the range from 42.0 MHz to 860.0 MHz. Th

• Grundig HDTV 1000 T, - 19 - - 19 - 5.4 Programming the cassette —> Pressing the button for longer than 2 seconds cancels the pro- gramming procedure. This takes you back to the program item “Selecting the cassette” from any menu. Any entries that have not been saved are reset to the previous settings. —> Entries in the menus can be saved by pressing the M key. You are taken back to the “Selecting the cassette” menu item. • Switch on the head-end station —> The display shows the software version (e.g. V 38) —>

• Grundig HDTV 1000 T, - 18 - - 18 - 5.3.2 Channel strip “A” with CA module Bx 4A Menu <= CA => Edit *) Die angezeigte Information ist abhängig vom verwendeten CA-Modul. The information displayed is dependent on the CA module used. Bx 4A 01/03 Information *) MENU Bx 4A TV X . . . . 04/09 S X – entschlüsselt decrypted 0 – verschlüsselt encrypted X / 0 nächster Service next service Bx 4A PID Check CA on ▶ ◀ on / off M ▶ ◀ / ! Bx 4A Menu <= CA => Edit Bx 4A Supply CA 5.0 V 3.3 V / 5.0 V Page 16 Page 16

• Grundig HDTV 1000 T, - 29 - - 29 - 2 This value shows the difference between the quality of the input signal and the threshold of the tuner at this type of modulation. At a value lower than “5” picture dropouts can oc- cur. 3 If “OK” is shown, the signal to noise ratio is ok. If a value < 5 is shown under 2 the display changes from “OK” to “??”. In this case test the input signal. —> In addition to the indicator in the display, there is also a status LED which indicates the quality of the

• Grundig HDTV 1000 T, - 34 - - 34 - COFDM parameters The tables below show the dependence of the transmittable net data rate on the settings of the COFDM parameters. The conversion of the net data rate into the gross data rate displayed in the ”Stuffing” menu is made according to the following formula: : 204 x net data rate Gross data rate = 188 Net data rate [kbit/s] at a bandwidth of 8 MHz Guard interval Modulation Code rate 1 / 4 1 / 8 1 / 16 1 / 32 QPSK 1 / 2 4976 5529 5855 6032 2 / 3 6635 7373 7806 8043 3 / 4 7465 8294 8782 9048 5 / 6 8294 9216 9758 10053 7 / 8 8709 9676 10246 10556 16 Q AM 1 / 2 9953 11059 1170

• Grundig HDTV 1000 T, - 38 - - 38 - • Use ▶ ◀ / to place the cursor under “POS”. • Use to set the spectral position to “NEG”. • Press the button. —> The “Setting the transmission parameters ” – “COFDM-MODE” menu is activated. Setting the transmission parameters In this menu you can set the transmission modes, the code rate and the guard interval. Transmission mode In this menu item you set the quantity of carriers: 2k mode: 1512 carrier for user data (total 1705 carriers) 4k mode: 3024 carrier for user data (total 3410 carriers) 8k mode: 6048 carrier for user data (total 6817 carriers) —> The standard modes for DVB-T are 2k and 8k.

• Grundig HDTV 1000 T, - 15 - - 15 - 5.3 Programming procedure 5.3.1 Channel strips “A” (without CA module) and “B” Bx 4A Channel OUTPUT Channel / Freq. Bx 4A C21 OUTPUT on on / off ▶ ◀ / Bx 4 Line A <= LINE => Line B Line A / Line B  BE–Remote please wait … V 38 Box 4 V 1 DVBS2-TPM COFDM – – – Box 1A C5-12,S3-24 TWIN-SAT C07 Bx 1A C5-12,S3-24 TWIN-SAT C07 Böx 4 C5-12,S3-24 TWIN-SAT C07 Bx 5A BD3 DVBT-DVBT C09 + t > 10 s Bx 4 A+B+ASI=1 INROUTE ASI=2 A+ASI=1 B+ASI=2 A+B+ASI=1 ASI=2 1=>ASI ASI=>MA 2=>ASI ASI=>MB ASI=>ASI  Bx 4 1=>ASI OUTROUTE ASI=>MA Bx 4 108000 KBits ASI RATE 188 / 204 positiv

• Grundig HDTV 1000 T, - 37 - - 37 - Setting the output signal In this menu, you can set the bandwidth, the carrier modulation and the spectral position of the output signal. Bandwidth of the output signal To transmit the output signal in the channel range of C21 to C69 a bandwidth of 8 MHz can be used. In the channel range of C5 to C12 a bandwidth of ≤ 7 MHz must be set. If frequency setting is selected you can set the bandwidth dependent on the frequency of the neighbouring-channel. • Use to set the bandwidth of the ou

• Grundig HDTV 1000 T, - 45 - - 45 - Saving settings • Press the M button. —> Returning to “Selecting the cassette” menu via con- nection A (page 19). —> The settings are saved. —> If functions of the TPS module are activated, their sta- tus is shown in the second line of the menu: “M” – Station filter is switched on. “N” – NIT is activated. “C” – Network/operator identification CAT is activated. —> By pressing the button, you will be returned to the menu item “Selecting the channel stri

• - 16 - - 16 - Bx 4A 27500 SYMBOL DVB-S Bx 4A 11836 -1.8 FREQ CN 12 ▶ ◀ / ▶ ◀ / ▶ ◀ / Bx 4A 0 dB LEVEL Bx 4A 10600 MHz LNB 0 … -10 dB Bx 4A 12.0 dB C/N (+ 9.6) OK Anzeige: Signalqualität Display: Signal quality ▶ ◀ / DVB-S / DVB-S 2 … Bx 4A Filter PROGRAM off 01/10Bx 4A TV + Das Erste Bx 4A Filter PROGRAM on on / off Programme entfernen / hinz

• Grundig HDTV 1000 T, - 11 - - 11 - • Insert the required number of F terminals in the openings provided in the head-end station or in the 19 ” cabinet. —> F terminals are not included in the scope of delivery. Tighten the nuts of the F terminals until the teeth on the lock washers put under have penetrated the exterior coating and a good connection is made between the housing / 19” cabinet and F terminals. 3.3 Connecting the cassette • Connect “ SAT input A ” 2 (channel strip “A”) and “ SAT input B ” 1 (channel strip “B”) to the respective outputs of the SAT IF input distributors. • Connect the ASI sockets 4 and 5. —> The LAN socket 3 is

• Grundig HDTV 1000 T, - 28 - - 28 - If a question mark “?” appears in the second line of the dis- play, there is no input signal present. In this case check the configuration of the antenna system and head-end station as well as the preceding settings of the cassette. • Use ▶ ◀ / to position the cursor under the digit of the frequency displayed to be set. • Press to set the respective digit of the input fre- quency needed. • Repeat the procedure by the quantity of the digits to be set. • Set the frequency offset shown in the display (e.g. “– 1.8”) to less than 1

• Grundig HDTV 1000 T, - 43 - - 43 - Network/operator identification In this menu, you can change the network/operator identifi- cation (CAT-ID – Conditional Access Table - Identification), for example of the visAvision transponder (Eutelsat 8° West). CAT is not to be changed: • Press the button. —> The “Deleting a PID” – “DROP” menu is activated (page 44). Changing the CAT: The network operator e.g. requires that you set the operator ID of the visAvision transponder to “2”. • Use the ▶ ◀ / buttons to position the cursor under the digit to be set. • Use to change the operator ID from “0xDE00�

• Grundig HDTV 1000 T, - 44 - - 44 - Deleting a PID In this menu a PID of the transport stream can be deleted. • Use the ▶ ◀ / buttons to place the cursor under the re- spective digit of the hexadecimal number of the PID to be deleted (“0x0000”) and set the hexadecimal number using . • Use the ▶ button to set the cursor under “ off ” and delete the PID using the buttons ( “ on ” ). • Press the button. —> The “Renaming a PID” – “REMAP” menu is activated. Renaming a PID In this menu you can allocate a new address to a PID retain- ing the compl

• - 8 - - 8 - 2.4.2.3 Menu setting “2 => ASI ASI => MB” Transport stream 1 is made available via modulator “A”, transport stream 2 via the ASI output and the transport stream from the ASI input “TS ASI” via modula- tor “B” (MB). 2.4.3 General The cassette is equipped with two channel strips (“ A ” and “ B ”). The channel strips consist of the d

• - 13 - - 13 - 4 The control panel at a glance 4.1 Menu items Program the cassette using the buttons on the control unit of the head-end station. The two-line display of the control unit then shows the menus. The parameters and functions to be set are underlined. Use the key to select the following main menu items: – Input signal path – Output sig

Related Products and Documents (Modulator):

Comparable Devices:

Similar Resources:

• Koheron CTL200-0 (3 pages) CTL200-0 User GuideNoteThis guide describes the information that is specific to the screw terminal version of the CTL200. Please refer tothe CTL200 user guide for general information on the CTL200.Terminal block connectionsLD+ / LD-: Laser anode / cathode pins. If possible, use a short twisted cable to connect your laser. TheCTL200-0 is compatible with float …

• Cirrus Logic CS5374 (44 pages) Copyright  Cirrus Logic, Inc. 2010(All Rights Reserved)Preliminary Product InformationThis document contains information for a new product. Cirrus Logic reserves the right to modify this product without notice.http://www.cirrus.comDual High-performance Amplifier & ΔΣ ModulatorFeatures High Input Impedance Differential Amplifier• Ultra-low input …

• Moog MF Chorus (2 pages) RATE - Specifies the rate at which the LFO (Low Frequency Oscillator) modulates the analog delay time. Slower settings are ideal for large classic sweeps, while faster settings create spinning, rotary and film projector effects. ECHO ROOMTIME - Minimum position is perfect for vibrato and bright chorus, while mid position shifts the tone to a deep choral mot …

• Marmitek MEGAVIDEO 55 (56 pages) AVIDEO 55MEGAVIDEO55TMUSER MANUAL 3GEBRAUCHSANLEITUNG 11GUIDE UTILISATEUR 19MODO DE EMPLEO 28MANUALE D’ISTRUZIONI 36GEBRUIKSAANWIJZING 4420168 / 20061212 • MEGAVIDEO55™ ALL RIGHTS RESERVED MARMITEK © 2007 …

• axing basic-line AVM 3-00 (4 pages) HerstellerAXING AG Gewerbehaus Moskau 8262 RamsenEWR-KontaktadresseBechler GmbHAm Rebberg 44 78239 RielasingenStand 2018-10-08Technische Verbesserungen, Änderungen im Design, Druckfehler und Irrtümer vorbehalten.Sicherheitshinweise:  Die Installation des Geräts und Reparaturen am Gerät sind ausschließlich vom Fachmann unter Beachtung der geltenden VD …

• Lumantek VENTUS F1 (37 pages) LUMANTEK Co., Ltd http://www.lumantek.com Head Oce : # 1208, Woolim Lion’s Valley II, 680 Gasan-Dong, Geuncheon-Gu, SEOUL, KOREA (150-803)TEL : +82-2-2027-2400 / FAX: +82-2-2027-2409 / e-Mail : [email protected] OPERATION MANUAL[Stand Alone Type Modulator]>>First EditionDAB / DAB+DTMBAWGNVENTUS F1 …

Comments, Questions and Opinions: