Manualios.com

Panasonic TX-47P500HM Service Manual

Panasonic TX-47P500HM Manual Online:

3.1, 1624 votes
Panasonic TX-47P500HM User Manual
Panasonic TX-47P500HM User Guide
Panasonic TX-47P500HM Online Manual

Text of Panasonic TX-47P500HM User Guide:

  • Panasonic TX-47P500HM, The convergence adjustment is set separately for each 50/100Hz/ 60/100Hz input (NTSC, PAL/ SECAM). The following explanation uses the PAL mode as an example, since the same procedure applies to the convergence adjustment for NTSC mode. When replacing the following Parts. IC7101 (EEP-ROM in Digital Convergence Circuit)L551 (Pincushion Coil)High Voltage Producing PartsOther Parts (If change the convergence) Create an Adjustment Sheet by tracing the following specifications in their actual size on transparent film or tracing paper.Then adjust the convergence. When replacing one of the CRT´s. 1. PAL (100i & 50p) 2. NTSC (120i & 60p) 3. 1080i Adjust the convergence for each of

  • Panasonic TX-47P500HM, 9.5. NTSC Tint Adjustment Preparation Picture Menu : Dynamic P-NR : ON C Temp : Standard Scan Mode : 100Hz (PAL) AI : ON Adjustment 1. Receive a Rainbow (NTSC 3.58Hz) pattern. 2. Connect an oscilloscope to TPLR1 on LR-Board. 3. Adjust Sub NTSC Tint so that the peak of level of waveform is similar to Fig. A. 4. Receive a Rainbow (NTSC 3.58Hz) pattern on both of Main and Sub picture. 5. Adjust Sub NTSC Tint 2 so that the peak of level of waveform is similar to Fig. B. 9.6. Sub Color Adjustment Preparation Picture Menu : Dynamic P-NR : ON C Temp : Standard Sca

  • Panasonic TX-47P500HM, 10.3.3.6. "B-LINEAR" adjustment Push the "TV/AV" buttons, and select the "B-LINEAR".Push the "Volume up/down" buttons, and adjust the "B-LINEAR". (Refer to Fig. C.) 10.3.3.7. "B-PIN (V)" adjustment Push the "TV/AV" buttons, and select the "B-PIN".Push the "Channel up/down" buttons, and adjust the "B-PIN (V)" (Refer to Fig. D.) 10.3.3.8. "B-PIN (H)" adjustment Push the "TV/AV" buttons, and select the "B-PIN".Push the "Volume up/down" buttons, and adjust the "B-PIN (H)". (Refer to Fig. E.) 10.3.3.9. "

  • Panasonic TX-47P500HM, 1.1. General Guide Lines 1. It is advisable to insert an isolation transformer in the AC supply before servicing a hot chassis. 2. When servicing, observe the original lead dress, especially the lead dress in the high voltage circuits. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 3. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers, shields, and isolation R-C combinations, are properly installed. 4. When the receiver is not to be used for a long period of time, u

  • Panasonic TX-47P500HM, Ref. No. Part No. Part Name & Description Pcs Remarks R454 ERJ6GEYJ123 M 12KOHM,J,1/10W 1 R455 ERG3FJS331D M 330 OHM, J, 3W 1 R456 ERJ6ENF9531 M9.53KOHM, 1/10W 1 R457 ERJ6ENF7151 M7.15KOHM, 1/10W 1 R458 ERJ6ENF3481 M3.48KOHM, 1/10W 1 R460 ERDS1FJ1R0 C 1 OHM, J,1/2W 1 R461 ERJ6GEYJ103 M 10KOHM,J,1/10W 1 R462 ERJ6GEYJ101 M 100 OHM,J,1/10W 1 R463 ERJ6GEYJ563 M 56KOHM,J,1/10W 1 R464 ERJ6GEYJ103 M 10KOHM,J,1/10W 1 R465 ERJ6GEYJ272 M 2.7KOHM,J,1/10W 1 R466 ERJ6GEYJ472 M 4.7KOHM,J,1/10W 1 R467 ERJ6GEY0R00 M 0 OHM,J,1/10W 1 R468 ERJ6GEYJ332 M 3.3KOHM,J,1/10W 1 R469 ERJ6GEYJ103 M 10

  • Panasonic TX-47P500HM, Procedure: 1. Cover the Red, Blue CRT lens, projecting Green only. 2. Adjust green centering magnet (DY) if the projected green horizontal/vertical line does not line up with the screen horizontal/vertical center line. 3. Cover the Green, Red CRT lens, projecting Blue only. 4. Repeat step 2. for blue. 5. Cover the Green, Blue CRT lens, projecting Red only. 6. Repeat step 2. for red. 7. Cover the Red, Blue CRT lens, projecting Green only. 8. Adjust green centering magnets until the center of the monoscope pattern line up with the screen center line. 9. Cover the Green, Red CRT lens, projecting Blue only. 10.

  • Panasonic TX-47P500HM, 12.3. DG-Board C500 C501 C503 C310 C505 C312 C507 Q310 Q311 C316 Q313 C317 C318 Q315 C319 Q317 Q318 Q319 C320 C708 C321 C709 C322 C323 C324 C325 Q321 Q322 C326 C327 D304 C328 C710 C329 R301 C711 R302 C712 C520 R304 Q711 Q329 Q713 R308 C330 C718 C331 IC301 R309 Q715 C334 Q330 IC304 C335 C336 IC306 C337 C338 IC308 R310 R311 R312 R313R314 IC310 IC311 Q725 C343 C344 C345 C347 IC318 C348 IC701 C733 R323 IC703 R900 Q730 R325 R901 R902 R326 C737 R327 R903 C350 C738 R904 Q735 R905 R329 C352 Q736 C353 Q737 Q738 Q739 C355 R715 C356 C358 C359 R333 R336 C746 R338 C748 R339 R722 C363 C367 R340 C750 C751 R729 C752

  • A Parts Location A-BOARD (FOIL SIDE) IC IC051 D-6 IC052 E-5 IC501 G-2 IC1104 C-4 IC1105 C-5 IC1108 A-1 IC1251 D-4 IC1252 B-4 IC1315 D-3 IC2001 E-4 IC2301 C-6 IC2302 A-3 IC2705 C-1 IC2706 A-1 IC2707 B-1 IC2708 C-2 IC2709 C-1 IC2710 F-4 IC3001 F-5 IC3002 G-3 IC3004 F-2 IC3005 F-2 IC7101 F-2 IC7102 D-1 IC7105 E-2 IC7108 F-2 IC7109 F-1 IC7110 E-2 TP7 F-6 TP8 E-6 TP9 E-3 TP10 E-3 TP11 C-5 TP12

  • 3.10. Disassembly For CRT Removal To facilitate CRT replacement, the complete CRT mounting chassis does not need to be removed. 1. Remove the Screen Frame Ass´y, Decorative Panel and the Bottom Rear Cover Ass´y. ( See Disassemble for Service ). 2. From the Rear side, remove the defective CRT´s anode lead from the Flyback Transformer block that is mounted s

  • Panasonic TX-47P500HM, Headphones: 3.5 mm Plug Aerial Impedance: 75 9 Unbalanced coaxial Video/Audio Terminals: AV1,2,3,4INS-Video in Y: 1.0 Vp-p 759 C: 0.3Vp-p 759 DVD (Y/P B /P R ) Video in 1Vp-p759 Audio in Approx. 0.5V 47k9 1 Safety Precautions 4 1.1. General Guide Lines 4 1.2. Leakage Current Cold Check 4 1.3. Leakage Current Hot Check (See Fig.1) 4 1.4. X-Radiation 4 2 Chassis Board Layout 5 3 Disassembly for Service 6 3.1. Disassembly Flowchart 6 3.2. Ornament Panel 7 3.3. Cabinet (Top) 7 3.4. Speaker Grille 7 3.5. Speaker Assエy 7 3.

  • Panasonic TX-47P500HM, 10.3. Coarse Convergence Adjustment mode 10.3.1. Green Coarse Convergence Adjustment 10.3.1.1. Reparation Push the "SOUND" button, and select the Green Adjustment mode.Push the "2" button, and select the "Border and Cross" pattern.Push the "MUTE" button, and select the "Green" colour. 10.3.1.2. "G-SIZE (V)" adjustment Push the "TV/AV" buttons, and select the "G-SIZE (V)".Push the "Channel up/down" buttons, and adjust the upper and lowe

  • Ref. No. Part No. Part Name & Description Pcs Remarks L1317 TALC168T6R8K CHIP INDUCTOR COIL 1 L1318,19 TALC325T4R7M CHIP INDUCTOR COIL 2 L1323,24 TALC325T4R7M CHIP INDUCTOR COIL 2 L1330 ELJPA330KB CHIP INDUCTOR 1 L1702,03 TALC325T4R7M CHIP INDUCTOR COIL 2 L1705,06 TALC325T4R7M CHIP INDUCTOR COIL 2 L1709-11 TALC325T4R7M CHIP INDUCTOR COIL 3 L1722 TALC168T8R2K CHIP INDUCTOR COIL

  • 3.6. Screen 1. Remove (14) screws. 3.7. Mirror 1. Remove (4) screws. 2. Remove (8) screws. 3.8. Rear Cover (Top) 1. Remove (4) screws. 2. Remove (2) screws. 3.9. Rear Cover (Bottom) 1. Remove (18) screws. 2. Remove (1) screws. 8 TX-47P500HM / TX-47P500HQ / TX-47P500HZ / TX-47P500X

  • Panasonic TX-47P500HM, Ref. No. Part No. Part Name & Description Pcs Remarks R2324-26 ERJ6GEY0R00 M 0 OHM,J,1/10W 3 R2327 ERJ6GEYJ103 M 10KOHM,J,1/10W 1 R2328 ERJ6GEYJ152 M 1.5KOHM,J,1/10W 1 R2330 ERDS2TJ101 C 100 OHM, J,1/4W 1 R2331 ERJ6GEYJ102 M 1KOHM,J,1/10W 1 R2333 ER0S2CKF4702 M 47KOHM, F,1/4W 1 EROS2CKF4702 R2335 ERJ6ENF6802 M 68KOHM, 1/10W 1 R2336 ERJ6GEYJ103 M 10KOHM,J,1/10W 1 R2337 ERJ6ENF1202 M 12KOHM, 1/10W 1 R2338,39 ERJ6GEYJ222 M 2.2KOHM,J,1/10W 2 R2340-42 ERJ6GEYJ103 M 10KOHM,J,1/10W 3 R2343 ERJ6GEY0R00 M 0 OHM,J,1/10W 1 R2344 ERJ6GEYJ103 M 10KOHM,J,1/10W 1 R2345 ERDS2TJ101 C 100 OHM, J,1/4W 1 R2346,47 ERJ6GEYJ223 M 22KOHM,J,1/10W 2 R2348 ERJ6GEYJ101 M 100 OHM,J,1/10W 1 R2349 ERJ6GEYJ223 M 2

  • Panasonic TX-47P500HM, 8.5. 525p Deflection Adjustment / Confirmation 8.5.1. V / H-Deflection confirmation 1. Receive 525p signal. 2. Confirm V / H-Deflection is normal. 8.5.2. H-Pos confirmation / Adjustment 1. Receive 525p signal. 2. Confirm H-Pos and if need, adjust H-Pos. 8.6. 625p Deflection Adjustment / Confirmation 8.6.1. V / H-Deflection confirmation 1. Receive 625p signal. 2. Confirm V / H-Deflection is normal 8.6.2. H-Pos confirmation / Adjustment 1. Receive 625p signal. 2. Confirm H-Pos and if need, adjust H-Pos. 22 TX-47P500HM / TX-47P500HQ / TX-47P500HZ / TX-47P500X

  • The Anode Lead 1. It inserts Anode lead tip in the back to FBT (the fly background transformer), and it makes turn on the right and it locks it. (Three insertion positions are free). 2. Secure a safe space distance from the circumference part by equal to or more than 10 millimeters. Attention 1. There is not sagging in Clamper -the D30 coupler pipe. 2. Drink

  • Panasonic TX-47P500HM, Ref. No. Part No. Part Name & Description Pcs Remarks R1083,84 ERDS2TJ101 C 100 OHM, J,1/4W 2 R1085 ERDS2TJ221 C 220 OHM, J,1/4W 1 R1101,02 ERJ3GEYJ562 M 5.6KOHM,J,1/16W 2 R1103 ERJ6GEYJ473 M 47KOHM,J,1/10W 1 R1104 ERJ6GEYJ101 M 100 OHM,J,1/10W 1 R1105 ERJ6GEYJ473 M 47KOHM,J,1/10W 1 R1106 ERJ3GEYJ472 M 4.7KOHM,J,1/16W 1 R1107 ERJ6GEYJ152 M 1.5KOHM,J,1/10W 1 R1108,09 ERJ6GEYJ272 M 2.7KOHM,J,1/10W 2 R1110 ERJ6GEYJ152 M 1.5KOHM,J,1/10W 1 R1111,12 TAJAAH0101JV M 100 OHM,J,1/16W 2 D0GB101JA006 R1113 ERJ3GEYJ103 M 10KOHM,J,1/16W 1 R1114 ERJ6GEYJ103 M 10KOHM,J,1/10W 1 R1115 ERJ6GEYJ101 M 100 OHM,J,1/10W 1 R1116 ERJ3GEYJ153 M 15KOHM,J,1/16W 1 R1117 ERJ3GEY

  • Panasonic TX-47P500HM, Ref. No. Part No. Part Name & Description Pcs Remarks C873 ECJ2VF1H104Z C 0.1UF, Z, 50V 1 C874 ECKCNA222MEB C 2200PF, M 1 C876 ECJ2VF1H223Z C 0.022UF, Z, 50V 1 C878 ECQU2A224MN P 0.22UF, M,250V 1 C880 ECA1EM472 E 4700UF, 25V 1 C883 ECA2WHG100 E 10UF, 450V 1 C884 ECQV1H104JM P 0.1UF, J, 50V 1 C885 ECKF1H101KB C 100PF, K, 50V 1 C886 ECCD3D270KGE C 27PF, K, 2KV 1 C888 ECKD3A392KBN C 3900PF, K, 1KV 1 C889 ECA1CM222 E 2200UF, 16V 1 C890 ECKD2H102KB2 C 1000PF, K,500V 1 C891 ECA1CM471 E 470UF, 16V 1 C893 ECKD3D681KBP C

Related Products and Documents (Projection TV):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Blanco BLANCODIAMOND 511-650 Specification sheet blanco/blancodiamond-511-650-24C.pdf 15 Sep 2023 1 0.28 Mb
2 Wolfgang Puck BDFR0060 Use & care manual wolfgang-puck/bdfr0060-2W4.pdf 09 Jun 2023 28 0.57 Mb
3 Omron C200HW-PRM21 Operation manuals omron/c200hw-prm21-16F.pdf 22 Mar 2024 126
4 Finishing Technologies Compact MINI Technical bulletin finishing-technologies/compact-mini-S66.pdf 19 Jul 2023 16
5 Honeywell RTH8580WF Operation & user’s manual honeywell/rth8580wf-63Y.pdf 22 May 2023 144 5.81 Mb
6 Royal Sovereign RBC-2100 Owner's manual royal-sovereign/rbc-2100-S68.pdf 20 Aug 2023 36 1.49 Mb

Similar Resources:

  • Philips

    Rear-Projection HDTV Monitor

    (8 pages)
    This section shows you how to make a basic TV connectionusing a cable TV or antenna signal.If you have cable TV service, you’ll simply connect the coaxialcable lead-in from the cable TV company to your TV. If you intendto connect a VHF/UHF antenna, you may need a 300- to 75-ohmadapter, which is not supplied with your TV. NOTE: You should be able to buy opt …
  • Samsung

    HL-R5688W - 56" Rear Projection TV

    (144 pages)
    Owner’s InstructionsHL-R5688WThis device is a Class B digital apparatus.Register your product at www.samsung.com/global/registerBP68-00489A-00(cover) 4/22/05 4:10 PM Page 3 …
  • Sony

    GRAND WEGA KDS-R60XBR2

    (2 pages)
    KDS-R60XBR2 60" Diagonal SXRD XBR Rear Projection Television Key FeaturesFull HD 1080 (1920 x 1080/0.61” SXRD chip) Picture Resolution WEGA Engine™ HD System DRC MF-V2.5Contrast Ratio up to 10000:1 with Advanced Iris functionATSC Integrated Tuner with CableCARD™ Slot HDMI™ (High Definition Multimedia Interface) x3 (1080p video) PC Input (D-S …
  • Epson

    Livingstation LS57P2

    (5 pages)
    About Your ManualThe instructions included with this TV are for your model of the Epson Livingstation, as well as the other models listed on the cover of the manual.The instructions refer to an external tuner, which is not included with the LS47P2C or LS57P2C. Otherwise, they are correct for your TV and describe how to operate it fully.À propos de votre man …
  • Sony

    KDP-51WS550 - 51" High Definition Projection Tv

    (285 pages)
    COLOR REAR VIDEO PROJECTION SERVICE MANUAL AX1 CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO.9-965-947-02KDP-51WS550 RM-Y192 US/CND SCC-M11CAKDP-57WS550 RM-Y192 US/CND SCC-M11AAKDP-65WS550 RM-Y192 US/CND SCC-M11BAHISTORY INFORMATION FOR THE FOLLOWING MANUAL:ORIGINAL MANUAL ISSUE DATE: 7/2003REVISION DATE REVISION TYPE …
  • Toshiba

    56HM195 - 56" Rear Projection TV

    (112 pages)
    (E) 56/62/72HM19556HM19562HM19572HM195Integrated High Definition DLP™ Projection TelevisionOWNER’S MANUAL© 2005 TOSHIBA CORPORATIONAll Rights ReservedOwner’s RecordThe model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this …

Comments, Questions and Opinions: