Philips CMP200 Operation & User’s Manual

Text of Philips CMP200 User Guide:

• Philips CMP200, 3 English EN Contents 1 Important 4 Safety 4 Notice 4 2 Yourcarpoweramplier 5 Introduction 5 What’s in the box 5 Overview of the main unit 5 3 Installation 7 Installation 7 Connect speakers 7 Connect car audio 8 Connect power 9 4 Useyourpoweramplier 10 Select crossover frequency mode 10 Adjust frequency 10 Adjust input level 10 Adjust bass boost 10 About the protector indicator 11 Replace fuse 11 5 Product information 12 6 Troubleshooting 13

• Philips CMP200, 4 Any changes or modications made to this device that are not expressly approved by Philips Consumer Lifestyle may void the user’s authority to operate the equipment. 2009 © Koninklijke Philips Electronics N.V. All rights reserved. Specications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. 1 Important Safety Read and understand all instructions • before you use the apparatus. If damage is caused by failure to follow in

• Philips CMP200, 5 Overview of the main unit a OUTPUT L/R Connect additional amplier for • additional speakers. b INPUT L/R Connect car audio with RCA cable.• c HI INPUT Connect car audio with the supplied • high input connector. d INPUT LEVEL Adjust input level (0.3V to 6V).• e PROTECT Lights in red when the PROTECTOR • is activated. f POWER Light in blue when power is turned on.• g FREQ Adjust frequency of HPF or LPF from • 30Hz to 400Hz. h HPF/OFF/LPF Select High-pass-lter (HPF), Low-• pass-lter(LPF) or OFF (at) mode. i BASS BOOST Boost the frequencies at around • 45Hz to a maximum of 12dB. a lk j bc dfeghi RL 2 Your car power amplifier Congratula

• Philips CMP200, 7 Connect speakers Note Use speakers with an impedance of 2 to 8 ohm • (4 to 8 ohm when used as a bridged amplier). Match the “left”, “right”, “+” and “-” terminals • correctly. Revised polarity may degrade sound quality. Option 1: Mono bridged mode: connect 1 speaker Option 2: Stereo mode: connect 2 speakers Option 3: Tri-mode: connect 3 speakers RL 4 ohm speaker RL 4 ohm speaker 4 ohm speaker 8 ohm speaker RL 4 ohm speaker 4 ohm speaker 3 Installation Installation You can mount the amplier either u

• Philips CMP200, 8 Connect car audio Option 1: High level input connection Connect the amplier to your car audio with the supplied High level input connector. Option 2: Line input connection Connect the amplier to the car audio with an RCA cable (not supplied) Option 3: Line output connection Connect the amplier to another amplier. Car audio unit White / Black White Grey Grey / Black Left speaker Right speaker LINE OUT Car audio unit EN

• 9 Connect power 1 Make the power connection as illustrated below: Connect the ground wire from the car to the • GND socket. Connect the remote wire from the car audio to the • REM socket. √ With this connection, you can turn on/off the amplier with the car audio. Connect the power wire from the car battery to the• +12V socket. Tip If your car audio does not have remote outp

• Philips CMP200, 10 1 Rotate FREQ to select frequency. Adjust input level You can adjust the input voltage from 0.3V to 6V. 1 Rotate INPUT LEVEL to adjust input voltage. Adjust bass boost You can punch extra bass for 0 to 12dB. 1 Rotate BASS BOOST to punch for extra bass. 4 Use your power amplifier Select crossover frequency mode You can select crossover frequency mode as below: HPF (high-pass- lter) mode Select this mode when mid-range speakers and tweeters are connected for high frequency output. LPF (Low-pass-

• 11 Replace fuse If there is no power, the fuse may be damaged and need to be replaced. 1 Pull out the damaged fuse. 2 Replace the fuse with the supplied fuses or to buy two fuses that matches the voltage of the damaged fuse (30A x 2). If the fuse gets damaged immediately after it has been replaced, there may be an internal malfunction. In such case, consult yo

• 12 5 Product information Note Product information is subject to change without prior notice. • Power output (RMS) - 4 ohm - 4 ohm (bridged) - 2 ohm 125W x 2 380W x 1 190W x 2 Total harmonic distortion 0.01% Signal to noise ratio 106dB Channel separation 50dB Frequency response 5-100kHz Input sensitivity 300mV - 6V Input impedance 22k ohm Fuse rating 30A x 2 Dimensions (DxWxH) 54.4 x 336.5

• Philips CMP200, 13 6 Troubleshooting To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site (www.philips.com/welcome). When you contact Philips, ensure that the apparatus is nearby and the model number and serial number are available. Power indicator does not light up The connected car audio is not turned on. • The fuse is blown. Replace the fuse with a new one. • The sound is too low. The input level is not set correctly

More Instructions:

Philips CMP200 Operation & user’s manual 18-09-2023 2

DOWNLOAD

Related Products and Documents (Car Amplifier):

Comparable Devices:

Similar Resources:

• Bazooka BTA6100 (2 pages) Bazooka Mobile Audio • 14763 Florida Blvd.Baton Rouge, LA. 70819 • 1-800-THE-TUBE www.bazooka.comWith real aluminum cones and butyl rubber surrounds, our premium motorcycle audio products offer more durability and audiophile sound quality than standard factory paper cone speakers or other after market polypropylene cone speakers. The alu …

• poly-planar RD-44 (6 pages) Poly Planar LLC 520 McCormick Dr. Glen Burnie MD. 21061 410-761-4000 www.polyplanar.com 2 Controls RD-44 Audio Network Control Panel Introduction: The RD-44 is designed to control the audio functions of Poly-Planar marine radios, amplifiers and audio sources. With versatile mounting options, the RD-44 can be installed up to 60 feet away from …

• Blaupunkt Velocity VD 502 (22 pages) Einführung (D)Herzlichen Glückwunsch zum Kauf dieses hochwertigen Car Audio-Verstärkers.Als Innovationsträger im Bereich CarHifi bieten wir Ihnen mit unserenClass D-Verstärkern den Einstieg in eine neue zukunftsweisende Tech-nologie.Im Vergleich zur herkömmlichen Analogtechnik verfügen Class D-Ver-stärker über einen wesentlich höheren Wirkungsgrad. …

• Kenwood KAC-7404 (10 pages) In store "130" you can find and buy almost all necessary goods for your auto in Kyiv and other cities, delivery by ground and postal services. Our experienced consultants will provide you with exhaustive information and help you to chose the very particular thing. We are waiting for you at the address http://130.com.ua PHONES (044) 360-7-130 (050) …

• JBL MS6100 (4 pages) THANK YOUfor purchasing JBL Marine Series speakers. We‘ve organizedthis manual to make your installation as simple and trouble-freeas possible. Please read it thoroughly before proceeding.Remember to keep your sales receipt and this manual in a safe place so both are available for future reference.MARINE SERIESMS6100MS6200MS9200marine speakerowner’s manu …

• Cadence ZRS C9 (4 pages) ZRS C9 QUICK INSTALLATION GUIDEREMOTE TURN-ONFROM HEAD UNITGROUND CONNECTION CABLESHOULD USE SAME GAUGEWIRE AS POWER CABLE. KEEP GROUND CABLE ASSHORT AS POSSIBLE. ALL AMPLIFIERS IN A MULTI-AMPINSTALLATION SHOULD GROUND TO THE SAMELOCATION TO AVOID GROUND LOOPS.POWER CABLE REQUIREMENT:4 GAUGE MINIMUM FOR 4-OHM BRIDGED OR 2-OHM STEREOHIGH POWER INSTALLS. YOU …

Comments, Questions and Opinions: