Heat & Glo VRTIKL-AU VRTIKL-AU Installation And Operation Instructions Manual

Text of Heat & Glo VRTIKL-AU VRTIKL-AU User Guide:

• 1 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 Installation & Operation Instructions Installation and service of this gas stove should be performed by qualifi ed personnel. AUSTRALIAN GAS ASSOCIATION CERTIFIED Certifi cate Number: 7153 Model: VRTIKL-AU FREESTANDING STOVE • Do not store or use gasoline or other fl am- mable vapors and liquids in the vi

• 3 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 Table of Contents 1 Listing and Code Approvals A. Design and Installation Considerations . . . . . . . . . . . . . . . 4 B. Non-Combustible Materials Specifi cation. . . . . . . . . . . . . . 4 C. Combustible Materials Specifi cation . . . . . . . . . . . . . . . . . 4 D. Inspect Appliance and Components . . . . . . .

• Heat & Glo VRTIKL-AU VRTIKL-AU, 21 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 A. Gas Pressure Requirements Pressure requirements for VRTIKL-AU Stoves are shown in Table 1 below. Two taps are provided on the right hand side of the gas control for a test gauge connection to measure the inlet and outlet pressures. See Section 10: Maintaining and Servicing the Appliance. The stove and its individual shut-off valve must be dis- connected from the gas supply piping system during any pressure testing of the system at test pressures in excess of 60 mbar. If the stove must be isolated from the gas suppl

• Heat & Glo VRTIKL-AU VRTIKL-AU, 22 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 BATTERY PORT (4 AA BATTERIES) VALVE PILOT IGNITION MODULE 6VDC ON/OFF SWITCH THERMOCOUPLE BLOCK (CONNECTED TO BACK OF VALVE) PILOT GAS LINE CONNECTED TO BACK OF VALVE IGNITION MODULE (6V) ON/OFF WALL SWITCH VALVE FLAME SPARKER/ SENSOR ANT. REMOTE CONTROL A. Ignition System Wiring • This gas stove is equipped with an electronic ignition system which operates on a 6 volt system. • The batteries are located within the ignition module whic

• Heat & Glo VRTIKL-AU VRTIKL-AU, 23 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 B. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox. The gas line is shipped inside back panel. To access the gas line remove the top plate from the gas stove. Remove and retain the two Allen head screws that hold the back panel in place. Replace panel when fi nished. C. Unbolting Appliance from the Pallet The gas stove is bolted and screwed to the pallet for ship- ping. Use a 1/2 in. socket to remove the bolt in center of bottom plate. Use a

• Heat & Glo VRTIKL-AU VRTIKL-AU, 24 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 Figure 7.4 The manufacturer recommends securing the lag bolt from the component bag in the center hole in the bottom plate (clearance hole). This bolt will help to prevent tip- ping forward. CLEARANCE HOLE Figure 7.5 Using pliers, adjust the counter screws to level the gas stove. E. Accessories Install approved accessories per instructions included with accessories. 4. Remove the inner extension collar (Shown in Figure 7.8) and set aside. 5. Remove the four screws from the DV adapter collar (Figure 7.8). Set aside DV adapter collar and screws. 3. Remove and retain the Allen head screws th

• Heat & Glo VRTIKL-AU VRTIKL-AU, 25 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 7. Install the cover plate with gasket to the top of gas stove with screws previously removed (Figure 7.10). Figure 7.10 ON BACK OF APPLIANCE: 6. Remove the four screws from the cover plate on rear of gas stove. Set cover plate aside. Retain screws. (See Figure 7.9). Attach DV adapter collar in its place. Install the inner extension collar. Figure 7.9 ON TOP OF APPLIANCE: 8. Install the new back panel (without hole) to the rear of gas stove. Replace the Allen head screws removed in Step 3 to ho

• Heat & Glo VRTIKL-AU VRTIKL-AU, 26 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 G. Positioning the Logs Figure 7.14 Place log #1 into the cradle in the burner. Lean the log back towards right corner of firebox. While still breakable, the logs do not become fragile until after the gas stove is burned and they have cured. After curing, any handling must be done with care as breakage can easily occur. PLEASE NOTE: Logs have been designed to work specifically with the burner of this gas stove. Exact placement will ensure proper operation of your gas stove. Figure 7.15 Locate log #2 over the pin in lo

• Heat & Glo VRTIKL-AU VRTIKL-AU, 27 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 A. Before Lighting Appliance Read this entire manual prior to using the appliance. Failure to follow the instructions may result in property damage, bodily injury, or even death. 8 8 Operating Instructions • Remove all shipping materials from inside and/or underneath the fi rebox. • Review proper placement of logs and mineral wool. • Check the wiring. • Check the baffl e adjustment. • Ensure that there are no gas leaks. • Ensure that the glass is sealed and in the proper position. • Ensure that the fl ow of combustion an

• Heat & Glo VRTIKL-AU VRTIKL-AU, 28 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 B. Lighting the Appliance Electronic Ignition LIGHTING INSTRUCTIONS TO TURN OFF GAS TO HEATER 1. Push the ‘OFF’ button on remote. 2. Remove batteries from receiver. FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fi re or explosion may result causing property damage, personal injury or loss of life. A. This heater is equipped with an electronic pilot ignition device which automatically lights the burner. Do not try to light the burner by hand. B. BEFORE LIGHTING, smell all around the heater area for gas.

• Heat & Glo VRTIKL-AU VRTIKL-AU, 29 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 ISSUE SOLUTIONS Condensation on the glass This is a result of gas combustion and temperature variations. As the gas stove warms, this condensation will disappear. Blue fl ames This is a result of normal operation and the fl ames will begin to yellow as the gas stove is allowed to burn for 20 to 40 minutes. Odor from gas stove When fi rst operated, this gas stove may release an odor for the fi rst several hours. This is caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Film on the glass This is a normal result of the curing process of the paint and logs. Glas

• Heat & Glo VRTIKL-AU VRTIKL-AU, 30 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 9 9 Maintaining and Servicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualifi ed service technician should perform an appliance checkup at the beginning of each heating season. Annual inspection by qualifi ed technician recommended. Check: • Condition of glass, glass assembly and glass seal. • Obstructions of combustion and ventilation air. • Burner ignition and operation. • Burner air shu

• 31 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 Inspect Maintenance Tasks Doors 1. Inspect for scratches, dents or other damage and repair as necessary. 2. Verify no obstructions to air fl ow. 3. Verify maintenance of proper clearance to combustible household objects. Gasket Seal, Glass Assembly and Glass 1. Inspect gasket seal and its condition. 2. Inspect glass for scratches

• Heat & Glo VRTIKL-AU VRTIKL-AU, 32 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 10 10 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualifi ed service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualifi ed service technician. Symptom Possible Causes Corrective Actions 1. No transmission, motor does not turn. A. Receiver must learn new code. Press and hold the receiver’s reset button until you hear 2 acoustic sign

• Heat & Glo VRTIKL-AU VRTIKL-AU, 33 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 A B G F H E Hearth Pad D C I Figure 11.1 Appliance Dimensions Height includes 9.53 mm hearth pad. AB C DEFGH I Millimeters 479 1045 1035 403 76 181 762 733 867 11 11 Reference Materials A. Appliance Dimension Diagram Without Stone Surround Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

• 34 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 G F A B C D E Hearth Pad B. Appliance Dimension with Stone Surround Diagram Figure 11.2 Appliance Dimensions with Stone Surround Height includes 9.53 mm hearth pad. ABCDEFG Millimeters 753 620 768 83 428 867 1126 Height includes 9.53 mm hearth pad.

• Heat & Glo VRTIKL-AU VRTIKL-AU, 35 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 C. Flue Components List COMPONENTS Ceiling Support / Wall Thimble, Black 656-230 150 mm Pipe Length, Black 908B 220 mm Pipe Length, Black 907B 310 mm Pipe Length, Black 906B 600 mm Pipe Length, Black 904B 910 mm Pipe Length, Black 903B 1210 mm Pipe Length, Black 902B 280 - 370 mm Pipe Length, Black 911B 310 - 430 mm Pipe, Adjustable, Black 912B 90 degree Elbow, Black 990B 150 mm Pipe SL-06D 220 mm Pipe SL-09D 310 mm Pipe SL-12D 600 mm Pipe SL-24D 910 mm Pipe SL-36D 1210 mm Pipe SL-48D 90 degree Elbow SL-90D Storm Collar

• Heat & Glo VRTIKL-AU VRTIKL-AU, 36 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 D. Service Parts 3 4 2 16 15 14 13 12 11 10 9 8 7 6 5 1 19 18 17 20 Service Parts Diagram VRT-GY-N-AU, VRT-BZ-N-AU VRT-GY-P-AU, VRT-BZ-P-AU Beginning Manufacturing Date: July 2007 Ending Manufacturing Date: ______ Part number list on following page. Log Set Assembly VRTIKL-AU

• Heat & Glo VRTIKL-AU VRTIKL-AU, 37 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 Service Parts List VRTIKL-AU Service Parts IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts. ITEM DESCRIPTION SERIAL # PART NUMBER Log Set Assembly 7031-033 1 Removable Top 2123-012 2 Top Assembly 7031-013 3 Adaptor 4 inch fl ue collar 200-2470 4 DV Adaptor 7000-162 5 Adaptor Gasket 460-0610 6 Side Assembly Left 2123-027 7 Firebox Assembly 2123-004 Heat Shield 2123-124 8 Latch Ass

• Heat & Glo VRTIKL-AU VRTIKL-AU, 38 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 Valve Assembly Parts List Service Parts Valve Assembly VRTIKL-AU Beginning Manufacturing Date: July 2007 Ending Manufacturing Date: ______ IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts. ITEM DESCRIPTION SERIAL # PART NUMBER 1 Log Bracket 7031-282 2 Pilot Assembly N 2098-050 Pilot Assembly P 2098-051 3 Pilot Bracket 7031-280 4 Burner Support 7031-279 5 Orifi ce N (#39C) 582-839 Orifi ce P (.057C) 582-057 6 Valve Bracket 2111-186 7 Burner N 2123-017 Burner P

• Heat & Glo VRTIKL-AU VRTIKL-AU, 39 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 E. Warranty Policy HEAT & GLO LIMITED 10 YEAR WARRANTY In order to presumptively establish the dates to which your HEAT & GLO Limited Warranty runs, you must mail the completed warranty card to HEAT & GLO, 20802 Kensington Boulevard, Lakeville, MN 55044, USA, within 60 days of the date of the stove installation. If you fail to do so, you may be required to prove the date of installation before warranty work can be performed

• Heat & Glo VRTIKL-AU VRTIKL-AU, 40 Heat & Glo • VRTIKL-AU • 2123-900 • 7/07 F. Contact Information Heat & Glo, a brand of Hearth & Home Technologies, Inc. 20802 Kensington Boulevard Lakeville, MN 55044, USA Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer, please visit www.heatnglo.com DEALERSHIP WHERE PURCHASED: ______________________________________ ______________________________________ _______________________________________ ____________________________________

Related Products and Documents (Cooktop):

Comparable Devices:

Similar Resources:

• GE Coil Top (44 pages) Coil Top and Radiant TopModelsRanges183D6379P010 49-88003 04-01 JRSafety InformationAnti-Tip Device . . . . . . . . . . . . 2Oven . . . . . . . . . . . . . . . . . . . . . 4Safety Precautions . . . . . . . 3, 4Self-Cleaning Oven . . . . . . . . 5Surface Units . . . . . . . . . . . 5, 6Operating InstructionsAdjust the Oven Thermostat . . . . . . . …

• Jenn-Air JDS8850BDW18 (96 pages) JENN-AIR _ DUAL-FUELSLIDE-iN RANGETABLE OF CONTENTSImportant Safety Instructions .....................................1-4Care & Cleaning ..............................................................5-7Maintenance .....................................................................8-9Troubleshooting ...................................................... …

• Frigidaire GLEFZ369F (9 pages) GLEF369DC.eps T20G5623.eps T20V0041.eps T20T0059.eps T20D0033.eps 316255102d.eps 316255102s.eps Product No. GLEFZ369FCA Series 30'f/s elec Color staniless Market North America Owner's Guide 316417029 Installation Instructions 316454901 Service Data Sheet 316441434 Electrolux Major Appliances North & Latin America P.O. BOX …

• Quadra-Fire 4300 Series (42 pages) 1 February 17, 20207037-802ANOTICE: DO NOT DISCARD THIS MANUALR4300 WOOD APPLIANCE SERIESAUTOMATIC COMBUSTION CONTROL (ACC)MODEL NUMBERS:43M-ACC-C43ST-ACC-COwner’s ManualOperation & CareINSTALLER: Leave this manual with party responsible for use and operation. OWNER: Retain this manual for future reference. Contact your dealer with questions on install …

• Northland RS7200 (44 pages) Installation, Operation & Maintenance Manual 2008RETAIN THIS MANUALCONSERVEZ CE MANUELUL 391, UL 726 & CSA B366.1OWNER’S MANUAL Models: RS7200 • RS7300 • RS7400 • RS7500 …

• Whirlpool RF367LXSB4 (7 pages) COOKTOP PARTS1For Models: RF367LXSQ4,RF367LXSB4,RF367LXSS4,RF367LXSY4(Designer White) (Black) (S.Steel) (Universal Silver)12−07 Litho in U.S.A. (mo)Part No. W10176981 Rev.A30" ELECTRIC CERANFREESTANDING RANGESELF CLEAN OVENIllus. PartNo. No. DESCRIPTION1 LiteratureW10141166Instructions,InstallationTemplate, Anti−Tip9757142 …

Comments, Questions and Opinions: