Manualios.com

HP ap5000 Hardware Reference Manual

HP ap5000 Manual Online:

4.65, 2924 votes
HP ap5000 User Manual
HP ap5000 User Guide
HP ap5000 Online Manual

Text of HP ap5000 User Guide:

  • HP ap5000, Removing and Replacing the VFD Customer Display 1. Turn off the computer properly through the operating system, then turn off any external devices. 2. Disconnect the power cord from the power outlet. CAUTION: Regardless of the power-on state, voltage is always present on the system board as long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 3. Remove the bottom I/O cover (see Removing the Bottom I/O Cover on page 6). 4. Unplug the VFD customer display's serial cable from the I/O panel. 5. Remove the plastic VFD hinge bracket cover by pulling outward on both upper si

  • HP ap5000, 11. Replace the power supply bracket by sliding the slotted end into frame (1) and tightening the thumbscrew (2). Figure 2-25 Replacing the Power Supply Bracket 12. Replace the bottom I/O cover (see Replacing the Bottom I/O Cover on page 6). 13. Turn the unit over and onto its base. 14. Plug the power cord into an electrical outlet and press the power button. ENWW Removing and Replacing the Power Supply 21

  • HP ap5000, Installing an HP/Kensington MicroSaver Security Cable Lock 1. Remove the bottom I/O cover (see Removing the Bottom I/O Cover on page 6). 2. Install the cable lock into the lock slot on the bottom I/O panel. Figure 2-12 Installing an HP/Kensington MicroSaver Security Cable Lock 3. Replace the bottom I/O cover (see Replacing the Bottom I/O Cover on page 6). 12 Chapter 2 Hardware Upgrades ENWW

  • HP ap5000, Installing Additional Memory The computer comes with double data rate 2 synchronous dynamic random access memory (DDR2- SDRAM) dual inline memory modules (DIMMs). DIMMs The memory sockets on the system board can be populated with up to two industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum memory support, you can populate the system board with up to 4-GB of memory. DDR2-SDRAM DIMMs For proper system operation, the DDR2-SDRAM DIMMs must be: ● industry-standard 240-pin ● unbuffered PC2-5300 667 MHz-compliant or PC2-6400 800 MHz-compliant ● 1.8 volt DDR2-SDRAM DIMMs The D

  • 1 Product Features Standard Features The HP ap5000 All-In-One Point of Sale System features include: ● Water-resistant touch screen so wet fingers are not be a problem. You can use a stylus, finger tip, finger nail, or credit card edge on the touch screen. ● Two-line customer facing vacuum fluorescent display (VFD). ● Three-track magnetic stripe reader (MSR) integrate

  • HP ap5000, About This Book This guide provides basic information for upgrading this computer model. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information. ENWW iii

  • HP ap5000, 12. Open both latches of the memory module socket (1), and insert the memory module into the socket (2). NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket. 13. Push the module down into the socket, ensuring that the module is fully inserted and properly seated. Make sure the latches are in the closed position (3). Figure 2-29 Installing a DIMM 14. Repeat steps 12 and 13 to install any additional modules. 15. After installing the memory module(s), place the top of the display head housing onto the display head (1), then set the b

  • HP ap5000, A Electrostatic Discharge A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. Preventing Electrostatic Damage To prevent electrostatic damage, observe the following precautions: ● Avoid hand contact by transporting and storing products in static-safe containers. ● Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations. ● Place parts on a grounded surface before removing them from their containers. ● Avoid touching pins, leads, or

  • HP ap5000, 5. To remove the hard drive from the plastic carrier, pull up on the two ends on one side of the carrier (1) and rotate the drive out of the carrier (2). Figure 2-19 Removing the Hard Drive from the Carrier 6. To insert the new drive in the carrier, hold the drive at a slight angle and place one side of the hard drive in the carrier (1), then press the other side straight down into the carrier (2). Figure 2-20 Placing the Hard Drive in the Carrier ENWW Removing and Replacing the Hard Drive 17

  • Table of contents 1 Product Features ............................................................................................................................................ 1 Standard Features ................................................................................................................................ 1 System Components .....................................

  • HP ap5000, 9. If you are replacing the VFD customer display, slide the new customer display into the slot on the hinge (1) and insert the two screws that secure it in place (2). Figure 2-16 Replacing the VFD Customer Display 10. Attach the hinge bracket cover by placing the upper sides of the cover over the sides of the bracket (1) then pressing the bottom of the cover onto the bracket so that it snaps in place (2). Figure 2-17 Replacing the VFD Hinge Bracket Cover 11. Replace the bottom I/O cover (see Replacing the Bottom I/O Cover on page 6). 12. Reconnect the power cord

  • HP ap5000, 7. Lift the power supply and its cables out of the base of the unit. Figure 2-23 Removing the Power Supply 8. Connect the external power cord to the power supply. 9. Route the circular end of the power cord through the hole at the top of the base and connect the power cord to the power connector on the bottom I/O panel. 10. Place the power supply into the base so that it is sitting on the metal tabs inside the base. Figure 2-24 Replacing the Power Supply 20 Chapter 2 Hardware Upgrades ENWW

  • HP ap5000, Index B bottom I/O panel components 3 removing cover 6 replacing cover 6 C cable lock 12 cable routing 9 components bottom I/O panel 3 side panel 4 system 2 computer operating guidelines 30 configuring COM port 27 customer display 15 MSR 15 touch screen 27 customer display configuring 15 removing and replacing 13 D DIMMs. See memory drive panel components 4 removing cover 8 replacing cover 8 E electrostatic discharge, preventing damage 29 F features 1 H hard drive location 4 removing and replacing 16 I installation guidelines 5 installing bottom I/O cover 6 cable lock 12 drive cover 8 hard drive 16 memory 22 MSR 26 power supply 19 side I/O cover 7 M memory installing 22 specificatio

  • HP ap5000, B Computer Operating Guidelines, Routine Care and Shipping Preparation Computer Operating Guidelines and Routine Care Follow these guidelines to properly set up and care for the computer and monitor: ● Although the display is water resistant, it is best to keep it away from excessive moisture, direct sunlight, and extremes of heat and cold. ● Never restrict the airflow into the computer by blocking any vents or air intakes. ● Never operate the computer with the cover or side panel removed. ● Do not stack computers on top of each other or place computers so near each other that they are subject to each other’s re-circulated or preheated air. ● If the computer is to be

  • HP ap5000, 3 Configuring the Software Calibrating the Touch Screen After the operating system is installed, you will need to calibrate the touch screen. NOTE: You may want to connect a mouse (not included) to the system for this procedure. 1. Launch the TouchMon utility by right-clicking on the TouchMon icon in the system tray and selecting 4 points calibration or selecting Start > All Programs > HP Touch > HP TouchMon Calibration. 2. When you see a red circle in the corner of the screen, touch the center of the

  • HP ap5000, Appendix A Electrostatic Discharge .............................................................................................................. 29 Preventing Electrostatic Damage ....................................................................................................... 29 Grounding Methods ............................................................................................................................ 29 Appendix B Computer Operating Guidelines, Routine Care and Shipping Preparation .......................... 30 Computer Operating Guidelines and Routine Care ....

  • HP ap5000, Adjusting the Tilt The main touch screen display has a 90 degree tilt range. The VFD customer display has an 80 degree tilt range. Figure 2-8 Adjusting the Touch Screen Display Tilt Figure 2-9 Adjusting the VFD Customer Display Tilt 10 Chapter 2 Hardware Upgrades ENWW

  • Removing and Replacing the Hard Drive CAUTION: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. 1. Turn off the computer properly through the operating system, then turn off any external devices. 2. Disconnect the power cord from the power outlet. CAUTION: Regardless of the power-on state, volt

  • HP ap5000, Routing Cables When connecting peripherals to the bottom I/O panel, route the peripheral cables through the bottom of the base and out the center hole at the top of the base before connecting. Figure 2-7 Routing Cables ENWW Routing Cables 9

  • HP ap5000, Removing the Drive Cover To remove the drive cover, loosen the screw that holds the cover in place (1), rotate the cover back (2), and pull the cover off the display head (3). NOTE: The drive cover screw is captive, therefore it does not disengage from the drive cover when loosened. Figure 2-5 Removing the Drive Cover Replacing the Drive Cover To replace the drive cover, slide the tabs on the cover into the slots on the side of the display (1), rotate the cover onto the display (2), then tighten the screw (3). Figure 2-6 Replacing the Drive Cover 8 Chapter 2 Hardw

  • HP ap5000, Removing the Bottom I/O Cover To remove the bottom I/O cover, press downward on the two tabs at the top of the cover (1) and rotate the cover off (2). Figure 2-1 Removing the Bottom I/O Cover Replacing the Bottom I/O Cover To replace the bottom I/O cover, insert the bottom of the cover (1) and rotate the top of the cover on so that it snaps in place (2). Figure 2-2 Replacing the Bottom I/O Cover 6 Chapter 2 Hardware Upgrades ENWW

Related Products and Documents (Cash Register):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Harbor Freight Tools 67632 Set up and operating instructions manual harbor-freight-tools/67632-329.pdf 10 Aug 2023 12
2 JUKI TL-2010Q Instruction manual juki/tl-2010q-569.pdf 06 Aug 2023 36
3 Charging Systems International Dual Pro SE Xtreme Installation and operating instructions manual charging-systems-international/dual-pro-se-xtreme-H42.pdf 11 Feb 2023 8
4 NETGEAR WNR1000v3 - Wireless- N Router Installation manual netgear/wnr1000v3-wireless-n-router-M2M.pdf 25 Feb 2024 2
5 Central Pneumatic 47612 Contractor Series Set up and operating instructions manual central-pneumatic/47612-contractor-series-48U.pdf 28 Sep 2023 12
6 Morphy Richards Cordless hand blender Instructions manual morphy-richards/cordless-hand-blender-L7J.pdf 05 Apr 2023 41

Similar Resources:

  • Sam4s

    ER-285M

    (7 pages)
    ER-285M Electronic Cash Register Operator's and Programming Manual All specifications are subject to change without notice. ©2007, CRS, Inc. M-ER285M Manual Version 1.4 For Fast Startup, See the “Quick Start Guide” on Page 13 Samsung ER-285m operation and programming ManualSamsung ER-285m operation and programming ManualSamsung E …
  • Sharp

    ER-A770

    (94 pages)
    MODEL ER-A770(For "V" version)CHAPTER 1. SPECIFICATIONS ................................................................1 - 1CHAPTER 2. OPTIONS ..............................................................................2 - 1CHAPTER 3. SERVICE PRECAUTION......................................................3 - 1CHAPTER 4. SRV RESET (Program Loop …
  • Sam4s

    ER-230 Series

    (147 pages)
    ER-230 Series Operation and Program Manual All specificaitons are subject to change without notice …
  • Casio

    TK-810

    (4 pages)
    THANK YOU YOUR RECEIPT CALL AGAIN ! HAMBURGERCOFFEEFRENCH-FRIESSANDWICHICE CREAMELECTRONIC CASH REGISTERTK-810OPERATOR'S INSTRUCTION MANUALEu Di U.K. 741085200963C TK-810 TK-810•10•10Casio TK-810 users and programming ManualCasio TK-810 users and programming Manual …
  • SignaPay

    Z8

    (2 pages)
    Customer Support 800.944.1399 Hours: Monday – Friday 8:00AM – 6:00PM CST Edit Tips Turn Server Prompt ON/OFFOn Screen Help Using Favorites1. Scroll using the Arrow keys highlight APPLICATIONS press OK Twice2. Scroll using the Arrow keys highlight TIPS AND TABS press OK3. Input Password (1234 is the Default) and press OK4. Select EDIT TIP p …
  • Sam4s

    ER-260 SERIES

    (87 pages)
    ELECTRONIC CASH REGISTER C O N T E N T S ER-260 SERIES ELECTRONIC CASH REGISTER Manual 1. Precaution Statements 2. Product Specifications 3. Installation and Operation 4. Disassembly and Assembly 5. Troubleshooting 6. Exploded Views and Parts List 7. PCB Layout and Parts List 8. Block diagram 9. Wiring Diagra …

Comments, Questions and Opinions: