Electrolux FN620K Owner's Manual
|
• Assembly • Operation • Maintenance • Service and Adjustments • Storage • Troubleshooting • Repair Parts OWNER'S MANUAL 184873 11.27.02 TR PRINTED IN U.S.A. MODEL NO. FN620K 3.5 HP 17 Inch Tiller 00137 For Parts and Service, contact our authorized distributor: call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886
Electrolux FN620K, 2 • Never operate the tiller without proper guards, plates, or other safety protective devices in place. • Keep children and pets away. • Do not overload the machine capacity by attempting to till too deep at too fast a rate. • Never operate the machine at high speeds on slippery surfaces. Look behind and use care when backing. • Never allow bystanders near the unit. • Use only attachments and accessories approved by the manufacturer of the tiller. • Never operate the tiller without good visibility or light. • Be careful when till
3 CONGRATULATIONS on your purchase of a new tiller. It has been designed, en gi neered and manu fac tured to give you the best pos sible de penda bil ity and per form ance. Should you experience any prob lems you can not easily remedy, please contact your nearest authorized service center. We have com pe tent, well-trained tech ni cians and the proper tools to servi
Electrolux FN620K, 4 ASSEMBLY OPERATOR’S POSITION (See Fig. 1) When right or left hand is mentioned in this manual, it means when you are in the operating position (standing behind tiller handles). Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) Utility knife (1) Pair of p
Electrolux FN620K, 5 ASSEMBLY TILLER HANDLES CABLE HANDLE PANEL BOLTS FIG. 2 HAN DLE PANEL HEX BOLT 5/16-18X3/4" TILLER HANDLE HEX BOLT 5/16-18X1" FLAT WASHER LOCK WASH ER NUT DEPTH STAKE SUPPORT BOLT HEX BOLTS, LOCK WASH ERS, AND HEX NUTS DEPTH STAKE SUPPORT NUT “A” ENGINE BRACK ET HALVES FIG. 3 STAKE SPRING INSTALL DEPTH STAKE ASSEMBLY (See Fig. 3) • Loosen nut “A”. • Insert stake support between engine bracket halves with stake spring down. • Bolt stake support to engine brackets with bolts, lock washers and nuts. Tighten se curely. Tighten nut “A”. • Dept
6 KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. RECOIL STARTER HANDLE DEPTH STAKE TINE SHIELD CHOKE CONTROL FORWARD TINE CONTROL TINES THROTTLE CONTROL These symbols may appear on your T
Electrolux FN620K, 7 OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask over spectacles or standard safety glasses. TRANSPORTING YOUR TILLER CAUTION: Before lifting or trans port ing, allow tiller engine and muffl er to cool. Disconnect spark plug wire. Drain gasoline from fuel tank. AROUND THE YARD • Tip depth stake f
Electrolux FN620K, 8 OPERATION FIG. 7 OIL FILLER PLUG OIL LEVEL TO START ENGINE (See Fig. 8) CAUTION: Keep drive control bar in “DISENGAGED” position when start- ing en gine. When starting engine for the fi rst time or if engine has run out of fuel, it will take extra pulls of the recoil starter to move fuel from the tank to the engine. • Make sure spark plug wire is prop er ly connected. • Move shift lever indicator to “N” (neutral) position. • Place throttle control in “FAST” position. • Move choke control to full “CHOKE” position. Grasp recoil starter handle with one hand and gras
Electrolux FN620K, 9 OPERATION • You will fi nd tilling much easier if you leave a row un- tilled between passes. Then go back between tilled rows. (See Fig. 9) There are two reasons for doing this. First, wide turns are much easier to negotiate than about-faces. Sec ond, the tiller won’t be pulling itself, and you, toward the row next to it. • Set depth stake and wheel height for shallow tilling when working extremely hard soil or sod. Then work across the fi rst cuts at normal depth. 321 5 4 67 FIG. 10 FIG. 9 CULTIVATING Cultivating is destroying the weeds between rows to pre vent th
Electrolux FN620K, 10 GENERAL RECOMMENDATIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must main tain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. • Once a year you should replace the spark plug, clean or replace air fi lter, and check tines and belts for wear. A new spark plug and clean air fi lter a
Electrolux FN620K, 11 MAINTENANCE FIG. 12 AIR CLEANER (See Fig. 13) Service air cleaner cartridge every twenty-fi ve hours, more often if engine is used in very dusty conditions. • Loosen air cleaner screws, one on each side of cover. • Remove air cleaner cover. • Carefully remove air cleaner cartridge. Be care ful. Do not allow dirt or de bris to fall into carburetor. • Clean by tapping gently on a fl at surface. • If very dirty or damaged, replace cartridge. • Clean and re pl
Electrolux FN620K, 12 MUFFLER Do not operate tiller without muffl er. Do not tamper with exhaust system. Damaged muffl ers or spark arresters could create a fi re hazard. Inspect pe ri odi cally and re place if nec es sary. If your engine is equipped with a spark arrester screen assembly, re move every 50 hours for cleaning and inspection. Re place if dam aged. SPARK PLUG Replace spark plugs at the beginning of each tilling sea- son or after every 50 hours of use, whichever comes fi rst. Spark plug type and gap setting is shown in “PRODUCT SPEC I FI CA TIONS” on page 3 of this man ual.
13 TILLER TO ADJUST HANDLE HEIGHT (See Fig. 15) Factory assembly has provided lowest handle height. Se lect handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. • If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets. • Slide handle panel to desired locati
Electrolux FN620K, 14 SERVICE AND ADJUSTMENTS TINE OPERATION CHECK (See Fig. 21) Be sure tines do not rotate when engine is running and tine control is in the “OFF” position. WARNING: Disconnect spark plug wire from spark plug to prevent starting while checking tine operation. FINAL CHECK “OFF” POSITION • With tine control “OFF” (up), push down on handle to raise tines off the ground. • Slowly pull recoil starter handle while observing tines. Tines should not rotate. • If tines rotate, place loop of idler spring in a lower link of chain and retest. FINAL CHECK “ON” POSITION • With tine control “O
Electrolux FN620K, 15 SERVICE AND ADJUSTMENTS V-BELT IDLER PUL LEY TRANS MIS SION PUL LEY BELT GUIDE ENGINE PULLEY BELT GUIDE TO REPLACE V-BELT (See Fig. 23) Replace V-belt if it has stretched considerably or if it has cracks or frayed edges. Belt guard must be removed to service belt. See “TO RE- MOVE BELT GUARD” in this section of manual. BELT REMOVAL • Remove V-belt from transmission pulley fi rst and then from engine pulley. FIG. 23 BELT REPLACEMENT • Install new V-belt to engine pulley fi rst then to trans- mis sion pulley. Be sure belt is positioned on i
Electrolux FN620K, 16 STORAGE ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CYLINDER(S) • Remove spark plug. • Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder. • Pull starter handle slowly several times to distribute oil. • Replace with new spark plug. OTHER • Do not store gasoline from one season to another. • Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems. • If possible, sto
Electrolux FN620K, 17 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in the Operation section. 3. Engine fl ooded. 3. Wait several minutes before attempting to start.
Electrolux FN620K, 18 REPAIR PARTS TILLER - - MODEL NUMBER FN620K HANDLE ASSEMBLY 1 137176X505 Bracket, Handle 2 72140512 Bolt, Carriage 5/16-18 UNC x 1-1¦2 3 9266R Grip, Handle 4 151473 Handle, L.H. 5 73680500 Locknut, Crown 5/16-18 6 19111116 Washer 11/32 x 11/16 x 16 Ga. 7 19121414 Washer 3/8 x 7/8 x 14 Ga. 8 74760516 Bolt, Hex Hd. 5/16-18 x 1 9 74760512 Bolt, Hex Hd 5/16-18 x 3/4 10 10040500 Washer, Lock 5/16 11 73220500 Nut, Hex 5/16-18 12 98000129 Nut, Flanged 5/16-18 KEY PART NO. NO.
Electrolux FN620K, 19 REPAIR PARTS TILLER - - MODEL NUMBER FN620K BELT GUARD AND PULLEY ASSEMBLY KEY PART NO. NO. DESCRIPTION 16 12000035 Ring, Klip 17 73350600 Nut, Hex, Jam 3/8-16 18 161806 Pulley, Idler 19 175377 Arm, Idler 20 74760620 Bolt, Hex 3/8-16 x 1-1/4 21 106968X Shaft, Idler Arm 25 73350500 Nut, Hex, Jam 5/16-18 KEY PART NO. NO. DESCRIPTION 1 23230506 Screw, Set 5/16-18 x 3/8 2 130812 Sheave, Engine 4 74610812 Bolt, Hex 1/2-20 x 3/4 5
Electrolux FN620K, 20 REPAIR PARTS TILLER - - MODEL NUMBER FN620K WHEEL AND DEPTH STAKE ASSEMBLY 1 9194R Pin, Clevis 2 74760520 Bolt, Hex 5/16-18 x 1-1/4 3 74760512 Bolt, Hex 5/16-18 x 3/4 4 73220500 Nut, Hex 5/16-18 5 10040500 Washer, Lock 5/16 7 4921H Clip, Hairpin 8 318J Support, Depth Stake, R.H. 9 9193R Stake, Depth 10 9551R Rivet, Drilled 13 317J Support, Depth Stake, L.H. 15 5388J Spring, Stake KEY PART NO. NO. DESCRIPTION 16
Electrolux FN620K, 21 KEY PART NO. NO. DESCRIPTION 1 165774 Tine, Outer, R.H. 2 4921H Retainer, Spring 3 165772 Tine, Inner, R.H. 4 165771 Tine, Inner, L.H. 5 165773 Tine, Outer, L.H. 6 9194R Pin, Clevis KEY PART NO. NO. DESCRIPTION REPAIR PARTS TILLER - - MODEL NUMBER FN620K TINE ASSEMBLY
22 REPAIR PARTS TILLER - - MODEL NUMBER FN620K TRANSMISSION KEY PART NO. NO. DESCRIPTION 16 19091412 Washer 9/32 x 7/8 x 12 Ga. 17 19092016 Washer 9/32 x 1-1/4 x 16 Ga. 18 10040400 Washer, Lock 1/4 19 74610412 Bolt, Hex 1/4-28 x 3/4 Gr. 5 20 - - - - - - - Engine, Briggs Model 94202 (Order parts
Electrolux FN620K, 23 KEY PART NO. NO. DESCRIPTION 1 132629 Decal, Logo 2 163989 Decal, Logo 4 127185X Decal, Description 5 110613X Decal, Tine Control 6 110614X Decal, Hand Placement 8 120076X Decal, Warning, Rotating Tines 9 171803 Decal, Briggs & Stratton 10 171806 Decal, 3.5 HP 11 162384 Decal, Warning 12 165327 Decal, Speed Control - - 184873 Manual, Owner’s (Engli
Electrolux FN620K, 00137 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de- fects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we fi nd to be defective due to materials or workmanship. This Warranty is subject to the following limita- tions and exclusions. 1. This warranty does not apply to the engine or components parts thereof. Pl
Poulan Pro 194800 Tiller Operator's manual
194800 |
Craftsman 316.292601 Tiller Operator's manual
316.292601 |
Weed Eater 151525 Tiller Owner's manual
151525 |
Bush Hog RTC40 Tiller Specifications
RTC40 |
Troy-Bilt Bronco CRT Tiller Service manual
Bronco CRT |
Land Pride CA2572 Tiller Specifications & capacities
CA2572 |
Electrolux Southern States SOR550 Tiller Operator's manual
Southern States SOR550 |
Snapper 1695066 Tiller Owner's manual
1695066 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Sindoh | DP200 Series | Operation & user’s manual | sindoh/dp200-series-66P.pdf | 09 Oct 2023 | 116 | |
2 | Biamp | 83 B Series | Operation manual | biamp/83-b-series-76F.pdf | 02 Oct 2022 | 28 | |
3 | Sony | CDX-434RF - Compact Disc Changer System | Operating instructions | sony/cdx-434rf-compact-disc-changer-system-EHC.pdf | 10 Sep 2023 | 4 | 0.18 Mb |
4 | Yamaha | RX-A1000 | Owner's manual | yamaha/rx-a1000-UYB.pdf | 21 Oct 2023 | 137 | |
5 | Haier | DW9-AFE | Operation & user’s manual | haier/dw9-afe-8E7.pdf | 20 Jun 2023 | 6 | 0.24 Mb |
6 | True Fitness | TA2H-4HG | Specifications | true-fitness/ta2h-4hg-2-2QC.pdf | 10 Sep 2022 | 2 | 0.16 Mb |
Wolf Garten
C 30 EC 30 EOriginalbetriebsanleitungOriginalbetriebsanleitungOriginal operating instructionsOriginal operating instructionsNotice d‘instructions d‘origineNotice d‘instructions d‘origineIstruzioni per l‘uso originaliIstruzioni per l‘uso originaliOriginele gebruiksaanwijzingOriginele gebruiksaanwijzingOriginale driftsvejledningOriginale driftsvejl …
C 30 E(120 pages) |
Stiga
STIGARECYCLINGVE308211-2504-80BRUKSANVISNINGKÄYTTÖOHJEETBRUGSANVISNINGBRUKSANVISNINGGEBRAUCHSANWEISUNGINSTRUCTIONS FOR USEMODE D’EMPLOIGEBRUIKSAANWIJZINGISTRUZIONI PER L’USOINSTRUCCIONES DE USOGUIA DE INSTALAÇÃOINSTRUKCJA OBS£UGIРУКОВОДСТВО ПО МОНТАЖУNÁVOD K POU®ITÍSZERELÉSI ÚTMUTATÓNAVODILA ZA UPORABOSV....4FI .....9DA..13 …
VE30 Recycling(84 pages) |
Husqvarna
ST 224, ST 227, ST 230EN Operator's manual 2-24DE Bedienungsanweisung 25-51ES Manual de usuario 52-76FR Manuel d'utilisation 77-101IT Manuale dell'operatore 102-126NL Gebruiksaanwijzing 127-151
…
ST 224(152 pages) |
Forges des Margerides
Notice d’utilisation et d’entretien OPERATING AND MAINTENANCE INSTRUCTIONS BETRIEBS UND WARTUNGSANLEITUNG ISTRUZIONI PER L’USO E LA MANUTENZIONE MANUAL DE UTILIZACION Y MANTENIMIENTO HANDLEING VOOR GEBRUIK EN ONDERHOUD INSTRUÇÕES DE UTILIZAÇAÕ E MANUTENÇÃOMotobineuse Tiller Motorhacke Motozappa Motoazada Motorhakfrees MotocultivadoraP337950 …
ES03B(18 pages) |
BCS
Precision CultivatorOWNER’S MANUALCultivadora de precisiónMANUAL DEL PROPIETARIOBineuse de précisionMANUEL D’INSTRUCTIONSThe Best Tiller on Earth La mejor excavadora en la TierraLa meilleure motobêche sur TerreBCS
…
7222ME(52 pages) |
Poulan Pro
OPERATOR'S MANUALMODEL:PRRT875XREAR TINE TILLERALWAYS WEAR EYE PROTECTION DURING OPERATIONVisit our website: www.poulan-pro.com WARNING:Read this Man u al and follow all Warnings and Safety Instructions. Fail ure to do so can re sult in serious in ju ry.IMPORTANT MANUAL Do Not Throw Away410241 Rev. 1 01.09.07 CLPrinted i …
410241(44 pages) |
Pittsburgh Tools PRO 00239#75U45V: PRO 00239 Tools Owner's manual & safety instructions PRO 00239, 4 |
OHAUS Scale SD SeriesScale #781226 SD Series, 37 |
A.O. Smith Boiler XB-1000Instruction manual for A.O. Smith XB-1000 Boiler XB-1000, 83 |
Generac Power Systems Portable Generator 1276-1Generac Power Systems 1276-1 Portable Generator Installation manual 1276-1, 10 |
Alcatel-Lucent IP Phone OMNISTACK 8008Alcatel-Lucent OMNISTACK 8008 User Guide (Doc Type: IP Phone Operation & user’s manual) OMNISTACK 8008, 52 |
Resolution Electronic dictionary RE124TGResolution RE124TG Electronic dictionary Instructions RE124TG, 2 |
Smeg Dryer APS61ESmeg APS61E User Manual (Operation & user’s manual), @M73DCP APS61E, 20 |
Singer Sewing Machine Scholstic 5523#3Z814R Scholstic 5523: Singer Sewing Machine Owner Documentation Scholstic 5523, 2 |
Cecilware Coffee Maker ESP1Coffee Maker Instruction manual (Cecilware ESP1) ESP1, 20 |
Mitsubishi Electric Air Conditioner MSZ-GE22VAService manual for Mitsubishi Electric MSZ-GE22VA Air Conditioner MSZ-GE22VA, 36 |
AOpen Motherboard MX3LGuide: AOpen MX3L (747983, Upd.Sunday 03-09-2023) MX3L, 83 |
Schwinn Stroller Single Seat Fixed Wheel Jogging StrollerStroller PDF Operation & user’s manual Single Seat Fixed Wheel Jogging Stroller, 16 |