Hitachi Printers Getting Started Manual

Text of Hitachi Printers User Guide:

• Hitachi Printers, 1-4 Unpacking and Setup Scanner Components Rear View Without Shroud ADF ADF Exit Table Extension Document Table Document Document ADF Cover Indicator Support Wire Guides OCP OCP Cable Cover Power Scanner Indicator Lamps Exit Table Switch Lamps Power Plug Inlet Image Processing Reset Switch SCSI ID Rotary Switch DIP Switches SCSI Connectors (Do Not Use) (Do Not Use) (Do Not Use) Printer Connector OCP Cable Board

• Hitachi Printers, Unpacking and Setup 1-1 Chapter 1 Unpacking and Setup Before You Begin Set up of the printer must be complete before you begin to set up the scanner. Selecting a Location The scanner must be located on a flat, stable surface near the printer. This can be a table or desk, or it can be the optional ScanCenter Stand. Whatever the location, be sure it is cleared and ready before you begin to unpack the scanner. CAUTION ! The printer is not designed to support the scanner. Do not attempt to set up the scanner on top of the printer. NOTE : If you are using the optional ScanCenter Stand, y

• © 1998, 1999 Hitachi Koki Imaging Solutions, Inc. All rights reserved. No part of this document may be reproduced without the expressed permission of Hitachi Koki Imaging Solutions, Inc. The material in this document is for informational purposes and is subject to change without notice. Hitachi Koki Imaging Solutions, Inc., assumes no responsibility for erro

• Hitachi Printers, 1-2 Unpacking and Setup Unpacking the Scanner Follow these instructions for unpacking the scanner. The packing arrangement is illustrated in the figure below. 1. Open the box. 2. Lift up and remove the left, right, and front packaging foam. 3. Lift up and remove the shipaway kit packaging. 4. Reach under the scanner, lift it out of the box and place it in the location you have prepared for it. 5. Place all of the packaging foam back in the box and save it for use in case you have to ship the scanner to another location. WARNING! The scanner weighs approximately 55 lb. Two people must be a

• Hitachi Printers, A-2 Safety Information Canadian Certification This Class A digital apparatus meets all requirements of the Canadian In- terference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règiement sur le matériel broilleur du Canada. Declaration of Conformity Declaration of Conformity Application of Council Directive(s): Standard(s) to which the Conformity is Declared: Manufacturer’s Name: Manufacturer’s Address: Type of Equipment: Model No.: The equipment specified above conforms to the Directives and to the Standards referenced above. Hitachi Koki Imaging Solutions, Inc. Simi Valley, California USA September 1998 73/23/EEC, 89/33

• Hitachi Printers, Safety Information A-3 CE Notice This equipment has been tested and found to comply with the limits for a class A Information Technology Equipment in accordance with the Euro- pean Standard EN55022. These limits are designed to provide reasonable protection against unacceptable interference in either commercial or industrial environments. This equipment generates, uses, and can radiate radio signals and if it is not installed and used in accordance with the instructions detailed in this user’s guide, it may cause unacceptable interference to radio communication installations and equipment. The operat

• Hitachi Printers, A-4 Safety Information Precautions ■ Read all of these instructions and keep them for later use. ■ Follow all warnings and instructions marked on the device. ■ Unplug this device from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. ■ Do not use this device near water. ■ Do not place this device on an unstable cart, stand, or table. The device could fall and suffer serious damage. ■ Slots and openings in the cabinet and the back or bottom are provided for ventilation. To ensure

• Hitachi Printers, Safety Information A-5 ■ Never push objects of any kind into this device through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. ■ Except as specifically explained in the user’s manual, do not attempt to service this device yourself. Opening or removing those covers that are marked “Do No Remove” may expose you to dangerous volt- age points or to other risks. Refer all servicing in those compartments to service personnel. ■ Unplug

• Hitachi Printers, 1-10 Unpacking and Setup Power Up To turn the power on, press the switch on the front of the scanner. A green LED will light on the front of the scanner and the touch panel will display a screen indicating the diagnostics are being run. When the diagnostics are complete (about 2 minutes), the touch panel will display the Job Status Screen. If the LED does not light, or the diagnostics fail, call technical support. Power Scanner Indicator LED Switch

• Hitachi Printers, Preface i Preface What This Manual Contains ■ Chapter 1 (Unpacking and Setup) shows how to unpack the ScanCenter, how to attach the necessary cables and power cord, and provides power up instructions. ■ Appendix A (Safety Information) provides safety, certification, and environmental information. Related Documentation ■ ScanCenter User’s Guide ■ ScanCenter Quick Reference Guide ■ ScanCenter Service Manual ■ Digital Document Server User’s Guide ■ ScanCenter Illustrated Parts List

• Hitachi Printers, Unpacking and Setup 1-9 Attaching the Cables and Power Cord to the Printer 1. If you are using the ScanCenter Stand, route the power cord and the printer cable down the back of the stand and secure them with the cable clamp. 2. Connect the printer cable to the printer interface where indicated below. 3. Plug the power cord into the wall outlet. Printer Cable from Scanner Printer Interface

• Hitachi Printers, Unpacking and Setup 1-7 Attaching the Shroud A shroud is attached to the scanner to protect the cables from coming loose and to provide a clean, finished appearance to the unit. To attach the shroud: 1. Unscrew the thumbscrews from the I/O plate and set them aside for later use. 2. Replace the thumbscrews with the standoffs. Thumbscrews (2) Standoffs (2)

• Hitachi Printers, 1-8 Unpacking and Setup 3. The power cord and the printer cable will be routed through an opening in the side of the shroud as it is installed. To ensure the printer cable stays connected, use the tie wrap to fasten the cable to the left standoff. 4. Mount the shroud onto the scanner. 5. Secure the shroud using the thumbscrews you removed in Step 1. WARNING! Never use the shroud as a handle for picking up the scanner. Tie Wrap

• Unpacking and Setup 1-3 Shipaway Kit Contents You will need the following items from the shipaway kit to set up the scanner: ■ Shroud ■ Standoffs (2 ea.) ■ Tie Wrap (1 ea.) ■ Printer Cable ■ Power Cord (USA and Europe only)

• Hitachi Printers, Unpacking and Setup 1-5 Installation Instructions Perform the following steps to install the scanner: 1. Place the scanner on a table or desktop not more than 6 feet from the printer. or Place the scanner on the optional ScanCenter Stand with the two left feet of the scanner in the cutouts on the left side of the tray. Attaching the Cables and Power Cord to the Scanner Attach the cables to the scanner as follows: 1. Locate the Operator Control Panel (OCP) cable that is taped to the side of the scanner and plug it into the OCP connector

• Hitachi Printers, A-6 Safety Information ■ Use the standard cable attached provided with the scanner. Other- wise, use cables that meet the following requirements:. Environmental Limit Following are the recommended environmental limits: ❒ Temperature range: 50 ° -90 ° F (10 ° -32 ° C) ❒ Humidity range: 20-80% RH Area Rating Plug Cable Connector North America 120V 10A NEMA 5-15P SVT or SJT 18/3 AWG Less than 1.6 m long IEC320 type Europe 230V (220-240V) 10A Use the required equivalent for each country H05VV-F or H05VVH2-F 3 x 1.00mm 2 EN60320 type WARNING! When using the optional ScanCenter Stand, do not place the scanner on the stand until the printer is in place and the

Related Products and Documents (Printer):

Comparable Devices:

Similar Resources:

• Oki ML393 (193 pages) iNote To CustomersEvery effort has been made to ensure that the information in thisdocument is complete, accurate and up-to-date. Mention ofsoftware packages manufactured by other companies does notnecessarily constitute endorsement by OKI. We do not assumeresponsibility for errors beyond our control, nor can OKI guaranteethat changes in the software and equ …

• Canon PIXMA MX310 Easy (2 pages) Start HereEasy Setup InstructionsaPlacethemachineonaatandhorizontalsurface,anddonotplaceanyobjectsinfrontofthemachine.Removealltheshippingtapesandprotectivematerialontheoutsideofthemachine.bLifttheScanningUnit(PrinterCover)withboth …

• HP Deskjet 3000 (2 pages) Deskjet 3000PrinterPrint and share everyday documents wirelessly with this compact, reliable HP printer.2 Designed to fit your lifestyle and your budget, it is easy to use and helps you conserve resources. Maximum Print Speed1: 20 ppm black, 16 ppm color Default Print Speed: Up to 5.5 ppm black, up to 4 ppm color Connectivity: 1 USB 2.0, 1 WiFi 802.11n Contr …

• Xerox Phaser 7750 (8 pages) Phaser® 7750 Color Laser PrinterCopyright © 2004 Xerox Corporation. All Rights Reserved.3-2Connections and IP AddressThis topic includes:■ "Printer Setup" on page 3-2■ "Connection Setup" on page 3-6Printer SetupEthernet Connection (Recommended)An Ethernet connection is recommended because it is faster than a USB cable connection. It …

• HP Designjet 3500cp (58 pages) 58%14%8%20%15844998325425488200018C4724A/C4723AHP DesignJet 3500CP PrinterHP DesignJet 3000CP PrinterSetup Guidesetup.bk Page 1 Monday, March 30, 1998 10:43 AM …

• Kyocera FS-3750 - B/W Laser Printer (2 pages) With optimal performance at minimum cost, the new FS-3750 is guaranteed to make the bestimpression anywhere. The quality of the print is exceptionally high, ensuring a professionalfinish for all documents and graphics. Thanks to its large memory capacity and high-performance processor, the FS-3750 completes all the tasks a demanding networkuser or large team …

Comments, Questions and Opinions: