Manualios.com

Hitachi PXR-D Instruction Manual

Hitachi PXR-D Manual Online:

3.65, 2467 votes
Hitachi PXR-D User Manual
Hitachi PXR-D User Guide
Hitachi PXR-D Online Manual

Text of Hitachi PXR-D User Guide:

  • Hitachi PXR-D, 1-26 ● Connection of signals Pin number Name Remarks 1NC 2 Ready NO 3 COM 4NC 5 Fault NO 6 COM 7NC 8 Warning NO 9 COM ¡ Connection to the external connection terminal block (TB2) (NOTE) NC :Normally closed NO :Normally open COM:Common • Terminal specification : M4 Pin number Name Input/Output Remarks 1 (NC) − Unconnected 2 RD Input 3 SD Output 4 (NC) − Unconnected 5SG− Ground 6 (NC) − Unconnected 7 (NC) − Unconnected 8 (NC) − Unconnected 9 (NC) − Unconnected ¡ Connection to the external communication (RS-232C) connector

  • 7-19 ● Adjusting the Ink Stream Position 2 1 7.7 Adjusting the Ink Stream Position Loosen the screw and then take off the print head cover. The ink stream adjustment procedure set forth below is to be performed after nozzle or orifice plate replacement. Under normal conditions, the ink stream needs no adjustment. ¡ The ink stream position must be adjusted so that the ink ejected fro

  • Hitachi PXR-D, ● Connection of signals 1-33 1.5.3-5 Printing stop signal The following describes the wiring of the signal that is entered from the outside to inhibit printing. (Note that the ready output signal remains unchanged even if this signal is entered from the outside.) Input specifications ・A no-voltage contact must be used for input. ・In the case of noncontact, the following requirements must be met. Withstanding voltage : 12 VDC or more Maximum drive current: 12 mA or more Residual voltage : 2 V or less Leak current : 0.1 mA or less Drive method : Open collector When the input is ON - While the IJ prin

  • Hitachi PXR-D, ● Operating Scheme 2-13 (2)The current status including the on-line/off-line (communication) state is constantly displayed at the top of the screen. 2.3.2 Status (1) The printer is in one of the following states. No. State Description 1 Stop The ink is stopped. No deflection voltage is applied. 2 Standby The ink is ejected. No deflection voltage is applied. 3 Ready The ink is ejected. The deflection voltage is applied (printing is permitted by the sensor signal). 5 Starting State in which the printer changes from the inactive state to the standby state. 6 Ink heating Start up in process, with the ink being heated. 7 Drop adjust Period during w

  • Hitachi PXR-D, 5-33 ● Editing/registering data that is different from that being printed 17 Press Edit message . "Edit message"screen will appear. KanaArabic Dedi- cated User pat- tern Calendar /count Punct. Insert Delete K U A L V B M W C N X D O Y E P Z F Q + G R − H S × I T / J Space Blank Back- space (). : , Edit message     Column 1        Column 2        Column 3  2011.07.07 12:45 Back Calendar conditions Count conditions 1234567890 ABC・ 123・ Manual Show cursor Prev. col. Next col. ↓ ↑ → ← Status: Read

  • Hitachi PXR-D, 2-12 ● Operating Scheme 2.3 Operating Scheme Save message Calendar conditions YES Printings (editing) Printings (menu) Auxiliary functions Edit message Print format Print specifications Menu Power ON Power OFF Print line setup Select message Select message Save message Print line setup Count conditions Calendar conditions Count conditions Back Edit message Print format Print specifications Back Maintenance Auxiliary function Maintenance Back Menu OK OK or OK Back : Input key : Screen name 2.3.1 Operating Scheme

  • Hitachi PXR-D, ● Managing Created Print Data 5-4 2 1 (1) Overview ¡ You can delete saved print data. (2) Operating procedure ¡Deleting the data stored in the No. 2 position 5.1.2 Deleting stored data Maintenance Auxiliary function Show fault Menu Operation management Environment setup menu 2011.07.07 12:45 Manage messages Create user pattern Calibrate touch screen coordinates Aux. function menu Back Manual Status: Stop Com=0 Start up Shut down Comm On/Off Copy data Select Languages Edit Standard pattern Create Messages Verify that the printer is in "Stop," or "Standby"

  • Hitachi PXR-D, ● Startup 2-9 Ejecting the ink using the control menu The confirmation screen opens. 1 Manual Control Menu The manual control menu appears. 2 3 Start up Shut down Manual Prev. col. Next col. ===== Maneal Control Menu ===== Eject ink: Ejects ink while applying no deflection voltage. No-cleaning stop: Stops ink ejection without cleaning. Eject ink No-cleaning stop Cancel The ink jet will be turned ON. Solution To turn the ink jet ON, press [Ready]. Ready Cancel ===== Ink Jet Startup Confirmation ===== Press

  • Hitachi PXR-D, 3-5 ● Setting Print Lines 3 2 1 4 Press OK . You are then returned to the "Print description" screen. For printings creation purposes, the number of line is set to 4 for columns 1 to 3. 》《     Column 1        Column 2        Column 3 [・・・・・・・・・・] [・・・・・・・・・・] [・・・・・・・・・・] [・・・・・・・・・・] [・・・・・・・・・・] [・・・・・・・・・・]  [・・・・・・・・・・] [・・・・・・・・・・] [・・・・・・・・・・]  [・・・・・・・・・・] [・・・・・・・・・・] [�

  • Hitachi PXR-D, 7-1 ● Circulation System Operating and Adjustment Procedures ¡ Never drain the ink or makeup ink waste solution into public sewer systems. Waste disposal must comply with all appropriate regulations.Consult the appropriate regulatory agency for further imformation. ¡ Exercise care not to inadvertently disconnect, forcibly pull, or bend a piping tube. Since the ink and makeup ink in some portions of piping tubes are pressurized, they may splash and enter your eyes or mouth or soil your hands or clothing. If the ink or makeup ink, enters your eyes or mouth, immediately flush with warm or cold water and see a physician. ¡ When charging a refill of ink or makeup ink

  • Hitachi PXR-D, 3-53 ● Setting high-speed printing 8 Set "High-speed print" to "NM". 9 Press the Back key and display the "Print description" screen. With above settings, high speed and high quality printing can be performed. Print specifications 2011.07.07 12:45 Back 1234567890 Incre- ment Decre- ment Manual Show cursor Status: Ready Com=0 Message name [ SAMPLE 1 ] Start up Shut down Comm On/Off Prev. set- tings Next set- tings ↑ ↓ Product speed matching [0] (0 : Time-based 1 : Encoder based) Pulse rate div. Factor [001] (1/1∼1/999 Ente

  • ● Setting the Date and Time 4-9 1 4.3 Setting the Date and Time (1) Overview ¡ The time values to be printed can be set in accordance with the calendar time. Either of the following two setup methods can be used. ¡The current time is used as the calendar time. Same as current time ¡A predefined time is used as the calendar time. ¡ You cannot set a time later than the current time

  • Hitachi PXR-D, 4-4 ● Setting the User Environment When the print target detection signal turns ON 4.2 Setting the User Environment (1) Overview Setup item Description Repeat print sensor mode Default ¡ Sets the conditions under which printing is performed a preselected number of times at predefined intervals. Signal ON period While the print target detection signal is ON Signal ON period OFF - ON transition ¡ Invalid if the repeat count is 0. Reverse direction printing Disable ¡ Set whether reverse direction printing is to be performed or not. When character orientation is normal (0, 1): Prints in reverse di

  • Hitachi PXR-D, 4-14 ● Controlling the Executable Functions 2 1 Choose Maintenance from the menu. Maintenance Auxiliary function Operation management Show fault Menu Environment setup menu It is presumed that "CZB05" is set as the password. (2) Operating procedure ¡ Performing setup so as to restrict the print data change function The "Maintenance menu" screen then opens. Maintenance menu 2011.07.07 12:45 Environment setup menu Operation management Test Print Excitation V update (Nozzle test) View software virsion View alar

  • Hitachi PXR-D, ● Using the Circulation Control Screen 7-4 5 The operating guidance, which varies with the selected function, then appears on the display. ¡ Perform an operation in accordance with the displayed operating guidance. ¡ To abort the operation, press the Abort key. Circulation control 20011.07.07 12:45 Proc. status: In progress. Function:Nozzle backwash Proc. time: Approx. 1 minute Status:Service Abort

  • Hitachi PXR-D, ● Transmission Sequences 6-25 Character size 5×5 5×8(5×7) 9×8(9×7) 7×10 12×16 18×24 24×32 Inter-character space 0 to 3 dots 0 to 3 dots 0 to 7 dots 0 to 3 dots 0 to 4 dots 0 to 6 dots 0 to 8 dots 24×32 × × ⃝ × ⃝ ⃝ ⃝ ⃝ Maximum number of vertical dots 20 dots 32 dots ¡ The total number of vertical dots cannot exceed the limit. Machine type Two lines machine Four lines machine ¡ Some characters cannot be entered depending on the character size. If a print item contains an unavailable character after a character size change, its contents are changed to a space. Input character types

  • 6-4 ● Setting Communication Environment Start bit Data length Parity bit Stop bits (bits) (bits) (bits) (bits) Start b0 b1 b2 b3 b4 b5 b6 Parity Stop 6.2.2 Transmission Specifications (1) Communication method: Half duplex (2) Startup method: Started up by host (3) Synchronization m

  • Hitachi PXR-D, 1-4 ● Usage Precautions (3) Storage precautions Store the ink and makeup ink in a cold dark place (0 to 20℃). (Observe this rule no matter whether tanks are unsealed or not.) The storage validity period is predefined for the ink and makeup ink. Begin to use the ink/makeup ink before the "Expiration date" (「開封期限」) date arrives. Once an ink bottle is opened, even if it is stored, the bottled ink begins to deteriorate in the same manner as the ink in the printer. If the above-indicated "approximate elapsed days" limit is exceeded, discard the bottle of ink. (When an ink bottle is opened, indicate the date of opening on the bottle&ap

  • Hitachi PXR-D, ● Startup 2-7 2.1.3 Operations for Modifying the Setting Contents ¡ You can modify the setting contents (print description, character height, excitation voltage, etc.) in any of the states "Ready," "Standby" and "Stop." (1) Operation in the "Ready" state ¡ Until you enter the Apply key, the setting contents on the display will not be reflected. When you have modified the contents, check that the Apply key is not on display and then restart printing. ¡ In case you enter a print terget s

  • Hitachi PXR-D, ● Transmission Sequences 6-29 ¡ For pattern data composition purposes, the data is arranged in successive order, beginning from the bottom left, from bottom to top and from left to right. b)Pattern data example a)For a character size of 5 x 5 Rotated 90 degrees counterclockwise Inter-character space data area ● ● ● ● ● ● ● ● ● ● ● ● First byte Second byte Third byte 4 byte 5 byte 6 byte 7 byte 8 byte ● ● ● ● ● ● Unusable area Removal of the first byte 0 0 0 0 0 1 1 1 = 07H 2

  • Hitachi PXR-D, ● Setting Print Lines 3-4 3 2 1 The "Print line setup" screen then opens. Print line setup type Print line setup 2011.07.07 12:45 Manual OK 1 line 2 lines 3 lines 4 lines Insert column Delete column Individual column setup Overall column setup Cancel Overall column setup : Sets same number of lines for all columns. Individual column setup : Sets number of lines for each column, or deletes column.     Column 1        Column 2        Colu

  • Hitachi PXR-D, 3-9 ● Setting Print Format 6 4 3 2 Press Back . You are then returned to the "Print description" screen. ¡ To correct another column, press Previous item or Next item and repeat steps 2 through 4 . Press Previous item or Next item to select an item whose print format is to be changed. Press ↓ or ↑ to move the cursor to the setup item to be edited. Change the value as desired with a numeric key, Decrement key, or Increment key. 1 1234567890 Incre- ment Decre- ment Print format 2011.07.07 12:45 Back     Column 1        Column 2       Column 3 [・・・・・・・・・・] 

  • Hitachi PXR-D, ● Installing Precautions 1-21 (14) If you try to fix the print head with a magnetic substance (such as iron), the cover switch will malfunction resulting in an "Cover Open" error. This, you must only use nonmagnetic resins or metals for fixing the print head. (15) In the case of carrying the printer proper, put in your hands from the direction of the arrow in the drawing below.

  • Hitachi PXR-D, 3-19 ● Printing Characters Press Next column . The cursor moves to the beginning of the second column. 3 Press ↓ . The cursor moves to the beginning of the second line in the second column. 4 The "Edit message" screen opens. KanaArabic Dedi- cated User pat- tern Calendar /count Punct. Insert Delete Edit message    Column 1        Column 2        Column 3 [USE BY・・・・] [YYMMDD・・・・] [・・・・・・・・・・]   [ABCXYZ・・・・] [・・・・・・・・・・] 

  • 3-35 ● Setting Character Height and Character Orientation (1)Overview ¡ The procedure for setting the character height, character width, character orientation and print start delay is described below. The "Print specifications" first screen. 3.4 Setting Character Height and Character Orientation Print specifications 2011.07.07 12:45 Character

  • Hitachi PXR-D, ● Pressure Adjustment 7-32 2 1 Verify that the ink is being ejected. From the menu screen, press the Maintenance key. The "Maintenance menu" screen then opens. 1234567890 Operation management  Ink operating time    [0000] (hours)  Ink alarm time      [1200] (hours; standard value:1200)  Cumulative op. time 000000 (hours)  Print count   [000000000] (prints)  Ink, makeup ink   JP-K27, TH-TYPE A  Ink viscosity

  • Hitachi PXR-D, 8-2 ● Indications Given When a Warning Condition/Fault Occurs If a warning condition occurs 2 ◇◇◇◇◇XXXXXXXXXXXXXXXXXXXX◇◇◇◇◇ The name of the warning condition is displayed here. A message of the warning condition is given here. The cause of the warning condition is indicated here.     XXXXXXXXXXXXXXXXXXXXXXX     XXXXXXXXXXXXXXXXXXXXXXX Cause  XXXXXXXXXXXXXXXX�

  • ● Printing Characters 3-30 Procedure for printing numbers from AA0001-AA1000 through AB0001 to ZZ1000 in the first line of the second row by incrementing the printed number by one after each printing 2 1 Perform steps through of procedure . 7 1 2 Change the following settings. This causes the cursor to move to the first line of the second row. Initia

  • 7-17 ● Correcting a Bent Ink Stream and Clogged Nozzle 1 Remove and clean the orifice plate. (1) Loosen the fixing screw and remove the charge electrode and deflection electrode. To prevent dropping, do not remove the screw. (2) Remove the four screws holding the orifice plate. Deflection electrode (+) Deflection electrode (-) Charge electrode Fixing screw Orifice plate (3) Use the

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Apogee Symphony Mk II Quick start manual apogee/symphony-mk-ii-8N6.pdf 26 Feb 2023 17
2 GE P2S975 Owner's manual ge/p2s975-OMD.pdf 06 Aug 2023 42
3 RKC INSTRUMENT X-TIO-B Instruction manual rkc-instrument/x-tio-b-37A.pdf 12 May 2023 6 0.29 Mb
4 Oki B2520 Operation & user’s manual oki/b2520-V31.pdf 26 Sep 2023 73
5 Panasonic RP-WF810 Operating instructions manual panasonic/rp-wf810-J72.pdf 12 Jul 2023 17
6 Pioneer DJM-S9 Firmware update manual pioneer/djm-s9-69X.pdf 05 Nov 2023 8

Similar Resources:

  • Panasonic

    SVP10U

    (28 pages)
    RBefore use, please read these instructions completely.VQT9628SD Mobile PrinterOperating InstructionsModel No. SV-P10UFor USA assistance. please call:1-800-211-PANA(7262) or send e-mail to:[email protected] Canadian assistance. please call:1-800-561-5505 or visit us at www.panasonic.ca …
  • Rimage

    Everest

    (1 pages)
    110660_D1 Rimage AutoEverest™ Setup and InstallationUnpack the Everest printer.1To unpack the Everest printer, refer to the Everest Unpacking and Setup Instructions included with your Everest printer.Install the Everest printer.2Place the Everest printer on the AutoPrinter so the plastic feet slide into the slots on the printer plate.Printer plateSlots for …
  • Dell

    1250C

    (2 pages)
    Dell™ 1250c Color Printer Quick Reference GuideAbout Your PrinterLocating the Service Tag1 Operator Panel 2 Output Tray3 Output Tray Extension 4 Print Head Cleaning Rod5 Toner Access Cover 6 Power Switch7 Paper Width Guides 8 Multipurpose Feeder (MPF)9 Front Cover 10 Length Guide11 MPF Extension 12 Paper Cover1 (Jam) indicator • Indicates that a paper …
  • Samsung

    6000 Series

    (346 pages)
    LED TVusermanualSERIES~600060500'.........#~#(;.....~#..-.#imaginethepossibilitiesThankyouforpurchasingthisSamsungproduct.ToreceivemorecompleteseNice,pleaseregisteryourproductatwww.samsung.com/registerModelSerialNo._LED TVusermanualSERIES~600060500'.........#~#(;.....~#..-.#imaginethepossibilitiesThankyouforpurchasingthisSamsungproduct.Toreceivemor …
  • Canon

    i550

    (57 pages)
    Color Bubble Jet PrinterColor Bubble Jet PrinterColor Bubble Jet PrinterColor Bubble Jet PrinterQuick Start GuideQuick Start GuideQuick Start GuideQuick Start Guide …
  • HP

    Deskjet 450 series

    (2 pages)
    The HP Deskjet 450 series – a compact, stylish and light mobile printer with desktop-quality performance, easy to connect to notebook,PDA or mobile phone for convenient and reliable printing – anytime, anywhere.HP Deskjet 450 seriesMaintain desktop efficiency and productivity even when you’re on the move. The HP Deskjet 450 series is designed for mobil …

Comments, Questions and Opinions: