Manualios.com

Whirlpool WDF310PLAT Installation Instructions Manual

  • WDF310PLAT Undercounter
  • maFu7CE.Y3rFQ
  • Installation Instructions Manual
  • PDF / Adobe Acrobat Reader
  • 48

Whirlpool WDF310PLAT Manual Online:

4.35, 2174 votes
Whirlpool WDF310PLAT User Manual
Whirlpool WDF310PLAT User Guide
Whirlpool WDF310PLAT Online Manual

Text of Whirlpool WDF310PLAT User Guide:

  • Whirlpool WDF310PLAT, 29 INSTRUCTIONS D'INSTALLATION Préparation de l'ouverture d'encastrement du placard – Moyens de raccordement pré-existants Si la canalisation d’eau et le câble dépassent des emplacements indiqués, passer à la section “Installation du tuyau d'évacuation”. S'ils ne sont pas assez longs, suivre les instructions dans la section “Préparation de l'ouverture d'encastrement du placard – Nouveaux moyens de raccordement”. Préparation de l'ouverture d'encastremen

  • Whirlpool WDF310PLAT, 20 Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors (not included). If needed, see website for animated representation of this step. Visit www.whirlpool.com/electrical under FAQ tab. Tighten strain relief screws to secure cable. Place wires inside terminal box. Insert tabs on left side of cover. Make sure wires are tucked inside box. Close cover ensuring wires are not pinched. Use ¹⁄₄" nut driver or Torx ® T20 ® screwdriver and previously removed screw to secure cover. Secure Dishwasher in Cabinet Opening Check that dishwasher is still level front-to-back and side-to-side in cabinet opening. Open d

  • Whirlpool WDF310PLAT, 13 Select UL Listed/CSA Approved twist-on wire connectors rated to connect your power supply cord to 16-gauge dishwasher wiring. Remove the green grounding screw and place through the ring terminal of the green ground wire. Reattach and tighten the green screw. NOTE: Do not pre-twist stranded wire. Twist on wire connector. Gently tug on wires to be sure both are secured. Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors. If needed, see website for animated representation of this step. Visit www.whirlpool.com/electrical under FAQ t

  • Whirlpool WDF310PLAT, 14 Determine Cabinet Opening Your dishwasher has leveling legs. The following provides instructions to adjust the leveling legs to set the dishwasher to the correct height for your cabinet opening. Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed (you will need to measure the lowest point on the underside of the countertop and the highest point on the floor). Refer to “Dishwasher Height Adjustment Chart” to adjust the leveling legs. NOTE: If the minimum cabinet opening height is less than 33⁷⁄₈"

  • 34 Préparation du lave-vaisselle En utilisant les fentes précoupées dans l'isolation, fixer l'excédent d'isolation sur les crochets moulés sur la cuve. Veiller à fixer l'isolation sur les deux côtés de la cuve. Conseil utile : Pour éviter d'endommager le revêtement de sol, placer une feuille de carton sous le lave-vaisselle jusqu'à

  • Whirlpool WDF310PLAT, 42 Raccordement électrique direct REMARQUE : Si le cordon d'alimentation a été raccordé précédemment, passer à la section “Fixation du lave-vaisselle dans l'ouverture d'encastrement du placard.” Option B, raccordement direct : Acheminer le cordon d'alimentation de façon à ce qu'il ne touche ni le moteur du lave-vaisselle, ni la partie inférieure de la cuve du lave-vaisselle. Tirer le câble pour le faire passer à travers le serre- câble (homologation UL/CSA

  • 43 Connecter le conducteur noir avec le noir et le conducteur blanc avec le blanc à l'aide des connecteurs de fils (homologation UL ou CSA) (non fournis). Au besoin, visiter le site Web pour une représentation vidéo de cette étape. Visiter www.whirlpool.com/electrical sous l'onglet FAQ. Resserrer les vis de serre-câble pour fixer le câble. Placer les cond

  • 16 Connect the ³⁄₈" compression fitting to the water supply line prior to installing the unit into the cabinet opening. Attach such that the ³⁄₄" connection is facing upward as shown above. Copper tubing only: Put the tubing into the 90° elbow fitting as far as it will go (the copper tubing bends and kinks easily). Slide the nut and ferrule forward and start t

  • Whirlpool WDF310PLAT, 35 Installer un serre-câble (homologation UL ou CSA). Veiller à ce que les têtes de vis soient orientées vers la gauche après le serrage de l'écrou du serre-câble. Le serre-câble est fourni avec le cordon d'alimentation. REMARQUE : Si l'on utilise l'option B, passer à “Évaluation de l'ouverture d’encastrement du placard” pour poursuivre l'installation du lave-vaisselle. Raccordement du cordon d'alimentation Option A, cordon d’alimentation : Acheminer le cordon d'alimentation de façon à ce qu'il ne touche pas la zone située entre le moteur du lave-vaisselle et la partie inférieure de la cuve du lave-va

  • Whirlpool WDF310PLAT, 11 Option D, No waste disposer – with air gap Prepare Dishwasher Using the precut slots in the insulation, fasten the insulation over the molded hooks on the tub. Be sure to fasten the insulation down on both sides of the tub. Helpful Tip: Place cardboard under dishwasher until installed in cabinet opening to avoid damaging floor covering. Do not use door panel as a worktable without first covering with a towel to avoid scratching the door panel. 1. Connect rubber end of drain hose to air gap and cut if needed. NOT

  • Whirlpool WDF310PLAT, 38 Option 1, Fixation au plan de travail Retirer les brides de l'emballage et les insérer dans les fentes ouvertes sur les côtés supérieurs droit et gauche du collet du lave-vaisselle, tel qu’indiqué. À l'aide d'une pince, replier la languette vers le bas pour fixer la bride. Répéter cette étape pour l'autre côté. REMARQUE : Ne pas fixer le lave-vaisselle. Ceci sera fait ultérieurement. Option 2, Fixation au côté du lave-vaisselle Pour plans de travail en marbre, granit ou autre surface dure Commander la pièce de la trousse de bride de montage n° 8212560. Préparation de la canalisation d'alimentation en eau

  • Whirlpool WDF310PLAT, 7 INSTALLATION INSTRUCTIONS Prepare Cabinet Opening—Existing Utilities If the water line and the cable extend to the locations shown, proceed to the “Install Drain Hose” section. If they do not reach far enough, follow the instructions in the “Prepare Cabinet Opening— New Utilities” section. Prepare Cabinet Opening—New Utilities Prepare and route the electrical supply Option A, Power Supply Cord: NOTE: A grounded 3 prong outlet is required inside a cabinet next to the dishwasher cabinet opening. Drill a 1¹⁄₂" (3.8 cm) hole in cabinet side or rear. See “Product and Cabinet Opening Dimensions” section. WARNING Disconnect electrical po

  • Whirlpool WDF310PLAT, 33 Option C - broyeur à déchets - avec brise-siphon Option D - pas de broyeur à déchets – avec brise-siphon 1. À l'aide d'un marteau et d'un tournevis, enfoncer le bouchon d'obturation dans le broyeur à déchets. 2. Retirer le bouchon d'obturation à l'aide d'une pince à pointe biseautée. 3. Raccorder l'extrémité en caoutchouc du tuyau d'évacuation au dispositif de brise-siphon et couper si nécessaire. REMARQUE : Ne pas couper la section ondulée. 4. Fixer le tuyau d'évacuation sur le dispositif de brise-siphon à l'aide de la grosse bride de tuy

  • Whirlpool WDF310PLAT, 45 Achever l'installation Placer le panneau d’accès en plastique contre le pied du lave- vaisselle. Vérifier que la rive inférieure du panneau d’accès est au contact du plancher. La réajuster au besoin. À l’aide d’un tournevis à lame plate, tourner les dispositifs de fixation d’un quart de tour pour les verrouiller. L’encoche du dispositif de verrouillage sera complètement à la verticale lorsqu’elle est correctement verrouillée. Brancher sur une prise de courant à 3 alvéoles reliée à la terre. Vérifier l’absence de tout contact entre

  • Whirlpool WDF310PLAT, 21 NOTE: Do not drop screws into bottom of dishwasher. Locate brackets on top of dishwasher and secure dishwasher to countertop with two, #10 x ¹⁄₂" Phillips-head screws (included). The dishwasher must be secured to keep it from shifting when door is opened. Check that top of door does not contact screws, brackets or countertop. If it does, adjust leveling legs. Open door and check that space between dishwasher cabinet opening and tub is equal on both sides. If spacing is not equal, loosen bracket screws secured and shift tub. Tighten bracket screws. Remove towel from dishwashe

  • Whirlpool WDF310PLAT, 28 Exigences d’évacuation ■ Un tuyau d'évacuation neuf est fourni avec le lave-vaisselle. Si ce tuyau n'est pas suffisamment long, utiliser un tuyau d'évacuation neuf de longueur maximale de 12 pi (3,7 m) (pièce numéro 3385556) qui satisfait les critères des normes de test AHAM/IAPMO en vigueur, est résistant à la chaleur et aux détergents, et peut être connecté au raccord d'évacuation de 1" (2,5 cm) du lave-vaisselle. ■ Veiller à raccorder le tuyau d'évacuation à la canali

  • 39 Insertion du lave-vaisselle dans l'ouverture d'encastrement du placard REMARQUE : Ne pas installer le garde-pieds avant que les instructions ne le spécifient. IMPORTANT : Vérifier que le câblage est installé au bon endroit. Saisir les côtés du lave-vaisselle par les rebords du panneau de porte. Approcher l’appareil de l’ouverture dans le placard. REMARQUE : Ne pas pous

  • Whirlpool WDF310PLAT, 18 Connect to Water Supply Be sure rubber washer is properly seated in fitting. Slide the ³⁄₄" fitting up to the valve and hand tighten to avoid cross- threading. Hand tighten until the coupling is tight. Using pliers, check the tightness of the coupling. An additional ¹⁄₄ to ¹⁄₂ turn may be required to seal the rubber gasket. NOTE: Do not overtighten. Damage to the coupling can result. Place paper towel under 90° elbow fitting. Turn on water supply and check for leaks. If leak occurs, repeat previous step. If needed, see website for animated representation of this step. Visit www.whirlpool.co

  • Whirlpool WDF310PLAT, 46 Contrôle du fonctionnement ■ Lire les instructions d'utilisation du lave-vaisselle fournies avec le lave-vaisselle. ■ Vérifier que toutes les pièces ont été installées et qu’aucune étape n’a été omise. Vérifier la présence de tous les outils. ■ Mettre le lave-vaisselle en marche et commander l’exécution complète du programme de lavage le plus court. Après les deux premières minutes, déverrouiller la porte; attendre cinq secondes, puis ouvrir la porte. Vérifier qu’il y a bien de l’eau au fond de la cuve du lave-vaisselle. V

  • Whirlpool WDF310PLAT, 37 REMARQUE : Si la hauteur libre minimale de l'ouverture d'encastrement du placard est inférieure à 33⁷⁄₈" (86 cm), on peut enlever les pieds de nivellement et les cales d'espacement arrière pour obtenir un dégagement supplémentaire. On pourra ainsi installer le lave-vaisselle dans une ouverture d'encastrement du placard d'une hauteur de 33¹⁄₂" (85,1 cm), mais il sera plus difficile de déplacer le lave-vaisselle. (Les mesures ne sont pas exactes. Les pieds de nivellement avant et arrière sont préréglés à l'usine pour une hauteur de 34¹⁄₂" [87,6 cm]). Ajuster les pieds de

  • Whirlpool WDF310PLAT, 22 Complete Installation Place the plastic access panel against the dishwasher leg. Check that the lower edge of the access panel touches the floor. Adjust if necessary. Using a flat-blade screwdriver, turn the fasteners ¹⁄₄ turn to lock into place. The fasteners slot will be straight up and down when properly locked. Plug into a grounded 3 prong outlet. Check that power supply cord does not touch dishwasher motor or lower part of dishwasher tub. Reconnect Power Electrical Shock Hazard Plug in

  • Whirlpool WDF310PLAT, 19 Make Direct Wire Electrical Connection NOTE: If the power supply cord was connected earlier, proceed to “Secure Dishwasher in Cabinet Opening” section. Option B, Direct Wire: Route cable so that it does not touch dishwasher motor or lower part of dishwasher tub. Pull cable through UL Listed/CSA Approved strain relief in terminal box. Strain relief is not supplied with the dishwasher. Owner must purchase a ⁷⁄₈" screw-in type strain relief. Select UL Listed/CSA Approved twist-on wire connectors (not included) rated to connect your household wiring to 16-gauge dishwasher wiring. Form bare

  • Whirlpool WDF310PLAT, 3 INSTALLATION REQUIREMENTS Tools and Parts Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. All Installations Tools needed: *Must be the proper size to connect your household wiring to 16-gauge wiring in dishwasher. Other useful items you may need: Parts supplied: Make sure all these parts are included in the literature package. Parts needed: Other parts you may also need: NOTE: Some parts available for purchase in plumbing supply stores. Check local codes. Check existing electrical supply. See “Electrical Requirements” secti

  • Whirlpool WDF310PLAT, 8 Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover hole with grommet included with power supply cord kit. Option B, Direct Wire: Helpful Tip: Wiring the dishwasher will be easier if you route the cable into the cabinet opening from the right-hand side. Drill a 1¹⁄₂" (3.8 cm) hole in right-hand cabinet side or rear. See “Product and Cabinet Opening Dimensions” section. Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover hole with grommet (Part Number 302797 - not provided). Route cable from power supply through cabinet hole (cable must extend to the right front side of cabinet opening). Tape cable

  • Whirlpool WDF310PLAT, 10 IMPORTANT: The drain hose connection of the disposer or a waste tee must be made before the drain trap and at least 20" (50.8 cm) above the floor where the dishwasher will be installed. Helpful Tip: To reduce vibration of the hose, keep the hose away from the floor. Option A, Waste disposer – no air gap Option B, No waste disposer – no air gap Option C, Waste disposer – with air gap 1. Using a hammer and screwdriver, knock plug into disposer. 2. Use needle-nose pliers to remove plug. 3. Attach drain hose to di

Related Products and Documents (Undercounter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Dirty hand 101172 Operation manual dirty-hand/101172-M3V.pdf 23 Aug 2023 20
2 Philips 6916531PH Manual  philips/6916531ph-6P4.pdf 11 Jun 2023 121 4.27 Mb
3 flopower FLOW160DA000 Operator's manual and parts list flopower/flow160da000-9V2.pdf 11 Jun 2023 18
4 Panasonic KX-PW507DL Quick reference manual panasonic/kx-pw507dl-WB4.pdf 10 Sep 2022 20 3.52 Mb
5 Philips 4CM6088 Operating instructions manual philips/4cm6088-758.pdf 04 Oct 2022 23
6 Solwise SAR-600 Easy start manual solwise/sar-600-OI3.pdf 11 Feb 2023 34

Similar Resources:

  • True Fitness

    TGW-3

    (2 pages)
    Specifi cations subject to change without notice.Chart dimensions rounded up to the next whole millimeter (inches rounded up to the next 1/8").ROUGH-IN DATAField’s End Road, Goldthorpe, Nr. Rotherham, South Yorkshire S63 9EU, England • www.truemfg.com • Tel 01709 888 080 • FAX 01709 880 838 • Free Phone 0 800 783 2049 • Free Phone to U.S. 0 …
  • Whirlpool

    WDF310PLAB

    (2 pages)
    U.S. Government Federal law prohibits removal of this label before consumer purchase.Cost Range of Similar Models$20 $50$30▼• Cost range based only on standard capacity models.• Estimated operating cost based on four wash loads a week and a 2007 national average electricity cost of 10.65 cents per kWh and natural gas cost of $1.218 per therm.• F …
  • True Fitness

    TUC-48-LP

    (2 pages)
    Specifi cations subject to change without notice.Chart dimensions rounded up to the nearest 1/8" (millimeters rounded up to next whole number).ROUGH-IN DATASt. Charles Industrial Center • P.O. Box 970 • O’Fallon, Missouri 63366(636)240-2400 • FAX (636)272-2408 • (800)325-6152 • www.truemfg.comParts Dept. (800)424-TRUE • Parts Dept. FAX# ( …
  • Sub-Zero

    UC-24RO

    (2 pages)
    Refrigerator-Freezer • Automatic Defrost• Cost range based only on models of similar capacity with automatic defrost.• Estimated operating cost based on a 2007 national average electricity cost of 10.65 cents per kWh.• For more information, visit www.ftc.gov/appliances.No. 7023301$32Cost Range of Similar ModelsEstimated Yearly Electricity UseY …
  • True Fitness

    TUC-93F

    (2 pages)
    Specifi cations subject to change without notice.Chart dimensions rounded up to the nearest 1/8" (millimeters rounded up to next whole number).ROUGH-IN DATASt. Charles Industrial Center • P.O. Box 970 • O’Fallon, Missouri 63366(636)240-2400 • FAX (636)272-2408 • (800)325-6152 • www.truemfg.comParts Dept. (800)424-TRUE • Parts Dept. FAX# ( …
  • True Fitness

    TUC-24

    (2 pages)
    Specifi cations subject to change without notice.Chart dimensions rounded up to the next whole millimeter (inches rounded up to the next 1/8").ROUGH-IN DATAField’s End Road, Goldthorpe, Nr. Rotherham, South Yorkshire S63 9EU, England • www.truemfg.com • Tel 01709 888 080 • FAX 01709 880 838 • Free Phone 0 800 783 2049 • Free Phone to U.S. 0 …

Comments, Questions and Opinions: