Manualios.com

Hitachi HV-HD201 Operation Manual

Hitachi HV-HD201 Manual Online:

4.3, 2019 votes
Hitachi HV-HD201 User Manual
Hitachi HV-HD201 User Guide
Hitachi HV-HD201 Online Manual

Text of Hitachi HV-HD201 User Guide:

  • Hitachi HV-HD201, 31 (All the masking menu settings become invalid in the OFF state.) 34) INITIALIZE : Returns MASKING menu settings to preset values. Simultaneously press L and R for about 2 seconds. 32 11. GAMMA/KNEE 1) GAMMA : Gamma ON/OFF Gamma correction is turned on/off. If the camera is in the auto mode (CAM MODE: AUTO), ON is selected unconditionally. 2) GAMMA TABLE : Sets gamma rising slope. Low : Dark component gradation reduced. Standard : Stand

  • Hitachi HV-HD201, 41 5) GL IN : Impedance changeover of input to the GL IN connector. • HIGH : The high impedance level is provided. • 75Ω : An impedance of 75 ohms is provided. Note: When power to the camera is turned off, the high impedance level is provided. So, do not use this function in a system where power is turned off for the camera unit only. 6) REMOTE : Set the remote control baud rate. 9600bps or 19200bps. (RC-Z3 allows 9600bps only.) Note: A setup cannot be changed in the remote

  • Hitachi HV-HD201, 68 6) Lens iris control output (Lens connector, manual override) DC Lens Mode IRIS CONT : 1.5 V (closed) to 7.5 V (open) (Selectable) VIDEO Lens Mode IRIS CONT : 0.0 Vpp to 1.0 Vpp

  • Hitachi HV-HD201, 62 DC IN DC INDC IN DC IN connector connector connector connector ( (( (R03 R03R03 R03- -- -R3M2 R3M2R3M2 R3M2) )) ) Pin No Signal designation A GND B +12V input C NC Plug Plug :R03-P3F S-VIDEO connector connectorconnector connector( TCS ( TCS( TCS ( TCS- -- -7547 75477547 7547- -- -01401) 01401)01401) 01401)

  • Hitachi HV-HD201, 9 Video signal type lens adjustment Adjustment is required after replacing the lens or if using the camera for the first time. 1) Preparation (1) Gain in the GAIN/SHT. manu is set to PRESET, and PRESET under that is set to +0dB. (2) If the light source has a flicker component (e.g., fluorescent or mercury lighting), change the electronic shutter mode (GAIN/ SHT. menu Shutter or Variable) to reduce the flicker. (3) Adjust the white balance. (Page 22) 2) Adjustment Hold the U button depressed and press Setup for about

  • Hitachi HV-HD201, M Table of contents  IMPORTANT SAFETY INSTRUCTUIONS····A  IMPORTANT NOTICE ······························· L  Table of contents······································· M  Standard composition ································ 1  Overview ················································· 1  Features ··········

  • Hitachi HV-HD201, 1 Standard composition Check when unpacking. Camera, HV-HD201 ····························· 1 Power plug, R03-P3F (JPR0034*) ··········· 1 Lens plug, E4-191J-100(JPE0001*) ········ 1 Operation Manual································ 1 * Part code Overview The HV-HD201 is a three CCD HDTV camera combining high picture quality and high stability with the convenience of C mount optics. CCD size is 1/2-size and each consists of 1,500,00

  • 49 Realtime Auto White The camera detects a white part in the image by itself, and its internal microcomputer automatically adjusts white balance in realtime. Use this function in case that the color temperature varies with time (e.g., from morning to day to night). 1. In the MENU mode, set up WHITE BAL:AUTO. Where the camera

  • 15 2) WHITE BALANCE : White balance mode Hue adjustment according to the color temperature of illumination so that a white image is picked up when the subject is white. • PRST 3200K : The white balance condition is optimized at a color temperature of 3200K. • PRST 5600K : The white balance condition is optimized at a color temperature of 5600K. • MEMORY : White balance is a

  • Hitachi HV-HD201, I l’appareil et le protéger de toute surchauffe, et ces ouvertures ne devront donc être ni obstruées ni recouvertes. Ne jamais obstruer les ouvertures en placant l’appareil sur un lit, un sofa, un tapis ou toute surface similaire. Ne jamais placer l’appareil dans un support confiné, par exemple une bibliothéque ou une é tagé re, sans ventilation suffisante ou sans repecter les instructions du fabricant. 11. Sources d’allmentation L’appareil devra être alimenté exclusivement sur le type d’alimentation indiqué sur l’étiquette signalétique. Sil’on n’est pas sûr du type

  • Hitachi HV-HD201, 64 Specifications 1) System HDTV system 4 mode 1080/59.94i, 1080/50i, 720/59.94p, 720/50p SDTV system 4 mode 576/50i(4:3), 576/50i(16:9), 480/59.94i(4:3), 480/59.94i(16:9) 2) Picture elements 1/2 - size CCD image sensor (Image size are 1/2-size) Total pixels 1504 (H) × 1099 (V) Effective pixels 1440 (H) × 1080 (V) Effective image area 6.98mm (H) × 3.92mm (V) 3) Imaging system R, G, B 3-CCD 4) Optical system 1/2 - size, F1.6 prism 5) Lens mount C mount (flangeback 17.526 mm in air) 6) Horizontal resolution 800

  • Hitachi HV-HD201, 21 5) ALC GATE SEL : Select ALC gate pattern Select pattern from among Modes 1, 2, 3, 4, 5 and 6. Use according to scene conditions. 検出領域 ALC [FILE1 ] OVER RIDE : 0 SPEED :STANDARD PEAK/AVE :15/85 ALC GATE :ON GATE SEL : PATTERN 1 ALC [FILE1 ] OVER RIDE : 0 SPEED :STANDARD PEAK/AVE :15/85 ALC GATE :ON GATE SEL : PATTERN 3 ALC [FILE1 ] OVER RIDE : 0 SPEED :STANDARD PEAK/AVE :15/85 ALC GA

  • Hitachi HV-HD201, 56 Store operation notes: 1. After adjustment and operation with the RC-Z3, neglecting the Store operation before pressing a file button loses the adjustment and setting item data. The output is the designated file data prior to adjustment and operation. 2. After adjustment and operation with the RC-Z3, neglecting the Store operation before cutting off the power loses the adjustment and setting item data. The output is the designated file data prior to adjustment and operation. Be sure to conduct the Store operation when desiring to save the data after adjustment and operation. In this case, the data prior to Store

  • Hitachi HV-HD201, 52 RC-Z3 Remote Control Panel All camera menu items can be operated remotely by connecting the RC-Z3 Remote Control Panel. Set camera’s rear panel switch RS-232C/RC-Z3 to RC-Z3 to connect the panel. Operation (1) Direct control The following items can be controlled directly as well as from the control panel. ・BAR/CAM ・ENABLE(ON/OFF) ・M.BLK ・WHITE BAL ・R GAIN ・A.WHT ・GAIN ・B GAIN ・A.BLK ・DTL ・R BLK ・SCENTE FILE ・IRIS MODE ・B BLK ・SHUTTE(ON/OFF) ・IRIS ・CONTRST(ON/OFF) (2) MENU controls All c

  • 3-CCD Color Camera MODEL HV-HD201 OPERATION MANUAL Please read this operation manual carefully for proper operation, and keep it for future reference. Note: The model and serial numbers of your product are important for you to keep for your convenience and protection. These numbers appear on the nameplate located

  • Hitachi HV-HD201, 43 3) DATA SET : : : : The DATA SET screen comes up. ID : Enter an ID code consisting of three characters. Alphanumeric upper-case characters and a space character are permitted. TITLE : Enter a TITLE consisting of up to 12 characters. Alphanumeric upper-case characters, special symbols and a space character are permitted. Note: The symbol " " in the data represents a space character. On the actual screen, a space character is given as a blank in an ID code or

  • 66 Input/Output Signals 1. Input signal conditions 1) Genlock input (MULTI connector) ・ ・・ ・ SYNC 0.3 Vp-p ±0.1Vp-p ・ ・・ ・ HD/VD 2 to 5 Vp-p, negative (MULTI connector) Note: Genlock input and Sync output are selected by internal input/output switch. External synchronization can synchroni

  • Hitachi HV-HD201, 5 Name and function each section 6 󲙳 󲙴 󲙵 󲙶 󲙷 󲙸 󲙹 󲙺󲙻󲙼󲙽󲙾󲙿󲚀 It set the operational mode of HDTV. 󲧩Please change it at power off state.) 󲧩Please change it at power off state.) Outputs HD-SDI signal. Outputs Y/C signal. Outputs VBS signal. Inputs SYNC signal of HDTV for external synchronization. The camera cable linked to a camera head is connected. Sets the signal level to connect to REMOTE terminal. (Please set it to 󲨓 󲨄-󲨛3 when camera is connected with r e m o te c o n t r o l

  • Hitachi HV-HD201, 13 SYSTEM ANALOG OUT SEL:HD TV RGB/Y PB PR :RGB OUTPUT SYNC :SYNC H PHASE : 0 GL IN :75 OHM REMOTE : 9600 BPS MESSAGE RTN :ON AUTO WHITE [FILE1 ] SPEED :STANDARD HIGH LIMIT :10000K LOW LIMIT :2500K WHITE GATE :OFF GATE AREA H : 4 GATE AREA V : 2 IN

  • Hitachi HV-HD201, 29 The following diagrams illustrate linear masking operations. 25) RG LINEAR: Color density and hue are changed in the direction of red-cyan axis. Blue and yellow do not change. 26) GB LINEAR: Color density and hue are changed in the direction of green-magenta axis. Blue and yellow do not change. 27) BR LINEAR: Color density and hue are changed in the direction of blue-yellow axis. Green and magenta do not change. RG LINEAR

  • Hitachi HV-HD201, 39 4) WHITE GATE : When WHITE GATE is ON, a detection gate is displayed dimly in white on the screen. • ON : In real time auto white balance operation or execution of memory auto white balance, a video signal appearing in the window on screen is detected for white balancing. In the MENU mode, the window is presented over the video signal. In the DIRECT mode, the window is not displayed but white balance control is conducted by the white gate function. • OFF : A video signal of the entire image is detected for carrying out white balance control. 5) GATE AREA H : Setting of detect

  • Hitachi HV-HD201, 7 Lens CAUTION: Observe the dimensions of the lens mounting selection as illustrated at the right. If the dimensions are not observed, do not use such a lens, because the lens and the camera will be damaged. Lens selection 1) Optical characteristics The proper lens is vital for obtaining full performance from the camera. The exit pupil distance is particularly important for a 3CCD type camera. If too short, vertical color shading can appear in the picture. Also, as the lens iris approaches

  • Hitachi HV-HD201, 17 2) SHUTTER : Electronic shutter mode Used to reduce the amount of light to an appropriate level or reduce the degree of after-image by reducing the time of light reception per image. Using SHUTTER makes the image darker. (Note) If a blinking light source such as a fluorescent lamp is used, flicker occurs. Setting a slower shutter speed improves immunity to flicker. In the case of inverter fluorescent lamps, their flickers are not like to give influence because they blink at high frequency although the flickers of some inverter fluorescent lamps include low frequency components. • OFF : Electronic shutter does not operate. •

  • Hitachi HV-HD201, 33 7) KNEE POINT : Use L and R to set in the range -128 (smaller) to 127 (larger). Normally set to where gradation appears above 100% video level. (To accurately check the image level, measuring equipment such as an oscilloscope is necessary.) 8) WHITE CLIP : Sets white clip level Use L and R to set in the range of - 128 (lower) to 127 (higher) clip level. Normally set for clip at about 110% video level. Adjust when there is excess video level from the equipment interface. 9) INITIALIZE : Returns GANNA/KNEE menu settings to preset

  • Hitachi HV-HD201, 35 5) SOFT DETAIL W. : Limits the maximum DETAIL level in bright image portions. DETAIL may be excessively effective where changes in brightness are large. In this case, it may be possible to make the image natural by limiting the maximum DETAIL level. SOFT DETAIL W. allows you to set the maximum DETAIL level on the bright side (white). 6) SOFT DETAIL B. : Limits the maximum DETAIL level in bright image portions. DETAIL may be excessively effective where changes in brightness are large. In this case, it may be possible to make t

  • 45 Notes: 1) Before this adjustment, set AGC to OFF and Shutter to Off. Return the previous settings after adjusting. 2) Open Limit needs to be set properly for normal AGC coupled operation. 5) CLOSE Limit : (Lens Type is DC mode.) Observe the iris and adjust to precisely the largest value (smallest diameter). The setting range is from - 128 to - 1. Press R

  • Hitachi HV-HD201, 11 Menu Screen Operation 1. Menu Structure For settings in the camera, the MAIN and SPECIAL menus are available. 1) MAIN Menu Structure Press the MENU button and MAIN MENU appears on the screen to indicate the main menu mode. Again press the MENU button to extinguish the menu and enter the direct mode. There are a main function setup menu and four sub-menus, which are arranged hierarchically as shown below. On the MAIN MENU, bring the cursor to GAIN/SHUTTER, DTL, ALC or AUTO SETUP and press the R button, and the desired subsidiary menu will come up. To return to the MAIN MENU from the GAIN/SHUTTER, DETAI

More Instructions:

DOWNLOAD

Related Products and Documents (Security Camera):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Clas Ohlson GN-BR32L-RH Instruction manual clas-ohlson/gn-br32l-rh-562.pdf 08 Dec 2023 56
2 Tennant 7400 Operator's manual tennant/7400-LFX.pdf 03 Feb 2024 88
3 Audio Note KASSAI Balanced Owner's information audio-note/kassai-balanced-624.pdf 25 May 2023 15 0.44 Mb
4 Senter ST801B Operation & user’s manual senter/st801b-V71.pdf 18 Dec 2023 14
5 Haan VersaSteam Pro BS-20 Instruction manual haan/versasteam-pro-bs-20-666.pdf 16 Mar 2023 24 4.89 Mb
6 Daewoo KOR-6L0B Service manual daewoo/kor-6l0b-61P.pdf 24 Sep 2022 32

Similar Resources:

  • Sony

    SSCFB560

    (2 pages)
    SSC-FB560Analog Color Fixed CameraKEY FEATURES700 TV Line Security Camera with Wide Dynamic RangeHorizontal resolution of 700 TV lines (sharp mode)CS mount lens not includedCompact designTrue Day/Night functionWide Dynamic Range With DynaViewSX TechnologyThe SSC-FB560 incorporates DynaViewSX technology to capture high-contrast scenes and produce clear images …
  • D-Link

    DCS-3716

    (48 pages)
    Documentation also available on CD and via the D-Link WebsiteQuick Installation GuideInstallations-AnleitungGuide d’installationGuía de instalaciónGuida di InstallazioneThis document will guide you through the basic installation process for your new D-Link Network Camera.DCS-3716Quick Installation GuideFull HD Day & Night WDR Network Camera …
  • i3 International

    Ax40W2-Series

    (38 pages)
    Ax40W2/4/8-seriesUser GuideBefore attempting to connect or operate this product, read these instructions carefully.Save this manual for future use. CONTENTS1. Warnings and operation notes..........................................32. Unpacking....................................................................53. Installation................................. …
  • HIKVISION

    DS-2CD886BF-E

    (13 pages)
    Quick Guide of Network Box Camera 1 Network Box Camera Quick Guide V3.0.0 Hangzhou Hikvision Digital Technology Co., Ltd. http://www.hikvision.com 2010-04 …
  • Bosch

    NBC-255-P

    (4 pages)
    IP Cameras Quick GuideF01U073063 June 2010General Surveillance Day/Night High Performance Megapixel ResolutionIndoor Indoor/Outdoor Indoor/Outdoor Indoor/OutdoorBosch IP Cameras200 Series 200 SeriesDinion IP SeriesFlexiDome IPDinion IP DN SeriesFlexiDome IP DNAutDome Easy II IPAutoDome IP Megapixel CamerasNBC-225-P(1)NBC-255-P(2)NDC-225-P(1)NDC-255-P(2)NBC- …
  • Schwaiger

    SECURE-4-YOU Series

    (2 pages)
    4. Start upLegal regulationsThe use and mounting location of surveillance cameras or replicas are subject to legal regulations and re-strictions. Violations may lead to an injunction suit. Please refer to the applicable regulations therefore before mounting and using the camera.Notes on assembly• This product is suitable for both indoor and outdoor use. � …

Comments, Questions and Opinions: