Whirlpool WHER25 Installation And Operation Manual

Text of Whirlpool WHER25 User Guide:

• 15 Step 6 - Connect Tubes CONNECT YELLOW TUBE TO STORAGE TANK 1. Locate the yellow tube. One end is attached to the Reverse Osmosis filter assembly. 2. Run the other end of the yellow tube to the fitting on top of the storage tank. See Fig. 22. 3. Cut tube square and to length. See Fig. 17. 4. Do not connect at this time. This will occur in the sanitizing step. CONNECT GREEN T

• Whirlpool WHER25, 6 Overview and Site Preparation OVERVIEW There are seven easy steps to installing your Drinking Water system. They are as follows: STEP 1 - Install Cold Water Supply fitting STEP 2 - Install Drain Adapter STEP 3 - Install Reverse Osmosis Assembly STEP 4 - Install Storage Tank STEP 5 - Install Reverse Osmosis Faucet STEP 6 - Connect Tubing STEP 7 - Sanitize, Pressure Test, Purge System These steps are explained in detail over the next few pages. It is recommended to read through the entire manual before beginning your installation. Follow all steps e

• Whirlpool WHER25, 18 How Your RO Water System Works HOW YOUR REVERSE OSMOSIS SYSTEM WORKS Introduction: Your Reverse Osmosis (RO) Drinking Water System uses your household water pressure to force water through three filters. Minerals and impuri- ties are filtered out. Delicious tasting drinking water goes to the storage tank-ready for your use. Minerals and impurities are sent down the drain. The following paragraphs will explain in detail how your Reverse Osmosis Drinking Water System works. Prefilter: Water from the cold supply pipe enters the prefilter. See Fig. 25. The prefilter has a replaceable sediment cartridge with activated carbon in its compo- sition.

• Whirlpool WHER25, 14 Cut tubing square with end of tubing round, smooth, with no cuts, nicks or flat spots. Step 6 - Connect Tubes Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223 FIG. 20 Tube Correctly Cut Collet Collet (Depress to Remove Tubing) Tubing Fitting O-Ring Seal Collet FIG. 17 HOW TO CUT AND CONNECT THE TUBES Your Reverse Osmosis Water System includes push-in fit- tings for quick tubing connection. Review the following instructions before connecting the tubes in the next step. Cut tubes to length 1. Use a sharp cutter or knife to cut the end of tubing. Always cut the tubing square. See Fig. 17.

• Whirlpool WHER25, 19 How Your RO Water System Works FIG. 25 PREFILTER PRODUCT WATER STORAGE RO MEMBRANE check valve drain flow control AUTOMATIC SHUTOFF WATER IN POSTFILTER PRODUCT WATER FAUCET air gap gravity drain RED YELLOW BLUE GREEN PRODUCT WATER BLACK WASTE WATER Water Flow Description 1. Water enters prefilter. Sand, silt and other sediments are reduced. Chlorine is also reduced. See Fig. 25. 2. Water leaves prefilter and proceeds to the Reverse Osmosis Cartridge. See Fig. 25. 3. Water enters the Reverse Osmos

• Whirlpool WHER25, 16 Step 7 - Sanitize, Test and Purge System SANITIZE THE SYSTEM Sanitizing is recommended immediately after installa- tion of the Reverse Osmosis system. It’s also recom- mended after servicing inner parts. It is important that the person installing or servicing the system have clean hands while handling inner parts of the system. Complete the following steps to sanitize the system. See Fig. 23. 1. Turn off the water supply to the Reverse Osmosis system. 2. Open the Reverse Osmosis faucet. If the tank is not already empty, allow

• Whirlpool WHER25, 3 Packing List Unpack and Check Your Carton INSPECT SHIPMENT Your Reverse Osmosis Drinking Water System is shipped complete in one carton. Remove all items from your shipping carton. Check all items against the packing list below. Note any items lost or damaged in shipment. Note any damage to the shipping carton. Refer to the exploded view and parts list in the back of the manual for the part names and numbers of missing or damaged items. If problems exist, refer to the website or the toll free numbe

• Whirlpool WHER25, 22 Specifications Supply water pressure limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-100 psi (280-689 kPa) Supply water temperature limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-100 °F (5-40°C) Maximum total dissolved solids (TDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000 ppm Maximum water hardness @ 6.9 pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 gpg Maximum iron,

• Whirlpool WHER25, 24 Troubleshooting Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223 Problem: Chlorine taste and/or odor in the RO product water. Cause: The level of chlorine in your water supply exceeds maximum limits, and has destroyed the Reverse Osmosis mem- brane. Correction: If the water supply contains more than 2.0 ppm of chlorine, addition- al filtering of the water supply to the Reverse Osmosis is needed. Correct this condition before doing maintenance on the Reverse Osmosis system. Cause: The prefilter is no longer reducing c

• Whirlpool WHER25, 8 Step 2 - Install RO Drain Under Sink FIG. 6 FIG. 7 FIG. 8 INTRODUCTION A suitable drain point is needed for the reject water from the Reverse Osmosis Filter. You have two options to choose from: • Install the Drain Adapter included with your unit See Fig 6, Fig. 7, and Fig. 8. This is used in under the sink installations. The drain adapter kit is installed onto your sink drain pipe above the P-trap. See Fig. 6. • Use another existing drain in your home (See Fig 9, Fig. 10) This is usually used in remote location type installations. The drain tube from the Reverse Osmosis Fi

• Whirlpool WHER25, 21 Maintenance FIG. 27 FLOW CONTROL The flow control is vital for proper operation of the Reverse Osmosis membrane cartridge. See Fig. 27. The flow control, located in the red tube at the system hous- ing, keeps water flowing through the membrane at the required rate. This is to ensure the system produces the best quality product water. Periodically check the flow control assembly to be sure the small hole through it is clean and unrestricted. If the flow control assembly requires service, review the exploded view in Fig. 27. Assemble and disassemble as shown. Flow Control Insert 1/4'' Red Tubing To Drain FIG. 29

• Whirlpool WHER25, 20 Maintenance PREFILTER/POSTFILTER MAINTENANCE NOTE: It is recommended to replace the battery, prefilter and postfilter cartridges at least every 6 months of product water use. Replace more often if they begin to plug with sediments. The prefilter and postfilter are replaceable sediment cartridges with activated carbon in its composition. See Fig. 26. You must periodically replace the prefilter and postfilter cartridge. This will protect the RO membrane from being destroyed by chlorine. It will also prevent the filters from plugging with sediments. You may notice a slower

• Whirlpool WHER25, 12 SELECT LOCATION OF REVERSE OSMOSIS FAUCET MOUNTING HOLE You will need to select the location of the Reverse Osmosis Faucet. You have three options to choose from: • Use the existing sink top hole for the spray hose or soap dispenser (Must be 1-3/8” in diameter) • Drill a new hole in the sink • Drill a new hole in the countertop next to the sink 1. Determine where you are going to install your Reverse Osmosis Faucet. 2. Check to ensure the Reverse Osmosis faucet will mount flat against the mounting surface. 3. Visually review the routing of the tubes from the Reverse Osmosis filter assembly to the f

• Whirlpool WHER25, 27 Parts List Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223 Key No. Part No. Description 1 9006062 Screw (2 req’d) 2 9041700 Hanger Washer (2 req’d) 3 7115432 O-ring (2 req’d) 4 7272658 Check Valve 5 7273337 Screw (6 req’d) 6 7281330 Washer (4 req’d) 7 7273345 Automatic Shut-off Cover 8 7250876 Diaphragm Kit 9 7234325 Plunger & Spacer Ring Kit 10 7275185 Flow (Control) Insert 11 WHEERF5 Pre & Post Filter Cartridge  12 WHEERM5 RO Membrane Cartridge  13 7205326 Storage Tank 14 9003203 Nut, 3/8” Tubing 15 7131349 Insert, 3/8” Tubing 16 7201681 Connector, 1/4 NPT x 3/8 Jaco 17 7208489 Drain Adapter 18 7011272 Sa

• Whirlpool WHER25, 25 Troubleshooting Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223 Problem: Water leaking from faucet airgap hole. Cause: Drain side of faucet airgap (3/8” black tub- ing) plugged, restricted or incorrectly con- nected to drain point. Correction: Inspect and eliminate restriction or plug. Refer to installation instruc- tions for proper drain connection. See Page 8 and 9. Problem: Faucet LED indicator light does not function after battery change. Cause: Battery dead. Correctio

• Whirlpool WHER25, 7 Step 1 - Install Supply Water Fitting Questions? Visit www.ecodyne.org or call Toll Free 1-866-986-3223 FIG. 5 Saddle Valve Connection (Included in package) Clamp Z Nut Nut - tighten if necessary Insert Ferrule (Plastic) Use to Connect Tubing Handle Valve Clamp X Seal CHOOSE TYPE OF WATER FITTING TO INSTALL Locate the cold water line in the sink cabinet. It is recom- mended, but not required, that the cold water line be soft water. You can use the saddle valve provided with your unit to tap into the cold water line. See Fig. 5. Or you can

• 9 Step 2 - Install RO Drain In Remote Location FIG. 10 FIG. 9 INSTALL A REMOTE DRAIN POINT AND AIR GAP (Remote Location) You can also run the drain tubing to an existing drain in the house. A floor drain, laundry tub, standpipe, sump, etc. are suitable drain points. See Fig. 10. This type of drain is the preferred over the p- trap drain adapter. Check your local codes. Longer lengths

• Whirlpool WHER25, 4 Plan Your Installation FIG. 1 PLAN YOUR INSTALLATION It is recommended to read through the entire manual before beginning your installation. Follow all steps exactly. Reading this manual will also help you get all the benefits from your system. Your Reverse Osmosis Drinking Water System can be installed under a sink or in a remote location. Typical remote sites are a laundry room or utility room. Review the location options below and determine where you are going to install your system. NOTE: For best system performance

• Whirlpool WHER25, 23 Warranty ONE YEAR LIMITED WARRANTY ON REVERSE OSMOSIS DRINKING WATER SYSTEM (Except filter cartridges and R. O. membrane) Warrantor: Ecodyne Water Systems Inc., 1890 Woodlane Drive, Woodbury, MN 55125 Warrantor guarantees, to the original owner, that the Reverse Osmosis Drinking Water System, when installed and maintained in accordance with the instructions, will be free from defects in materials and workmanship for a period of one year from date of installation. If, within the first year, a part proves, after inspection,

• Whirlpool WHER25, 2 TABLE OF CONTENTS Unpack and Check Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Plan Your Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Overview and Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Step 1-Install Supply Water Fitting . . . . . . . . . . . . . . . . . . . . .

More Instructions:

	Whirlpool WHER25 Installation and operation manual 01-01-2023 23	DOWNLOAD
	Whirlpool WHER25 Performance data sheet 15-08-2023 2	DOWNLOAD
	Whirlpool WHER25 Installation and operation manual 07-11-2023 27	DOWNLOAD

Related Products and Documents (Water System):

Comparable Devices:

Similar Resources:

• Afriso EURO-INDEX ProCalida GT 3 (28 pages) Mess-, Regel- und Überwachungsgeräte für Haustechnik, Industrie und Umweltschutz Lindenstraße 20 74363 Güglingen Telefon +49 7135 102-0 Service +49 7135-102-211 Telefax +49 7135-102-147 [email protected] www.afriso.de  Read instructions before using device!  Observe all safety information!  Keep instructions for future use! 12.2013 0 854. …

• Cetetherm Midi Compact SR144 (50 pages) DOC1312 Rev:2020-06-01 Installation, service and operating instruction Cetetherm Midi Compact SR144 DHWC Heating and domestic hot water substation for apartment houses (10-50 apts.) …

• Hellenbrand Reverse Osmosis Systems GRO Series (2 pages) GRO SeriesHellenbrand’s GRO Series Reverse Osmosis SystemsHigh Quality, Light Duty Industrial / Commercial Reverse Osmosis SystemsThe GRO Series systems provide high quality water at a low cost. The base systems have optional packages to meet most facilities control and monitoring requirements.GRO Series Benets • Dependable and simplistic operation …

• Kenmore 625.34842 (64 pages) OWNER'SMANUALMODEL NO.625.348420Caution:Read and FollowAll Safety Rules andOperating InstructionsBefore First Use ofThis Product.If you have questions wheninstalling, operating or main-taining your softener, andwhen setting the timer, callthis toll-free number...1-800-426-9345SAVE THIS MANUALDemand Special EditionWater Softener• Warranty• Start Up / …

• EINHELL GC-AW 6333 (96 pages) GC-AW 6333Art.-Nr.: 41.767.30 I.-Nr.: 110157D Originalbetriebsanleitung HauswasserautomatGB Original operating instructions Automatic domestic water systemF Mode d’emploi d’origine Systeme automatique d‘eau a emploi domestiqueI Istruzioni per l’uso originaliCentralina idrica automaticaS Original-bruksanvisningPumpautomatNL Originele handl …

• Nikken PIMAG WATERFALL (22 pages) gravity water system/système d’eau gravitationnel/sistema de agua y gravedadPIMAG WATERFALL®OPERATING MANUAL / GUIDE D’UTILISATION / MANUAL DE USOThe PiMag Waterfall Gravity Water System is tested and certified by WQA to NSF/ANSI 42 for the reduction of aesthetic chlorine, aesthetic chloramine, taste and odor, Particulate Class III ANSI/NSF 53 for redu …

Comments, Questions and Opinions: