Philips ADAT-4 Operation & User’s Manual
|
Graham-Patten is a division of Printing History SoundPals ™ ADAT-4 ADAT-to-AES converter Rev. N/C March 2007 Printed in U.S.A. Part Number 08-2054-00 The information contained in this guide is subject to change without notice or obligation. Copyrights and Trademarks © 2005 GRAHAM-PATTEN SYSTEMS, INC. Contents of this publication may not be reprodu
Philips ADAT-4, Table of Contents ii • Table of Contents ADAT-4 User Guide Table of Contents ii Introduction 1 What are SoundPals?..............................................................................................................1 Documentation Conventions.................................................................................................... 1 Signals and Values ............................................................................................................
Philips ADAT-4, Introduction ADAT-4 User Guide Page 1 What are SoundPals? Each Graham-Patten SoundPals module is essentially a digital audio building block that can be used independently, or interconnected to perform more advanced mixing and audio processing functions. SoundPals can be used in both standalone and system configurations: • In a “standalone” configuration, each SoundPals module is designed to perform a specific audio processing function such as ADAT-to-Analog conversion. In this way, each module functions as a perfect low-cost adjunct to larger mixing consoles (such as the Graham- Patten D/ESAM series) �
Philips ADAT-4, ADAT-4 User Guide Page 2 Unpacking and Inspection When you receive your SoundPals modules, inspect the cartons for signs of damage. Contact your dealer and the shipper immediately if you suspect any damage has occurred during shipping. Check the contents of each box to be sure that all parts are included. If any items are missing, contact your dealer immediately. Power Supply Note SoundPals are delivered with a power connector only. A separate power supply must be obtained. Graham-Patten offers several power solutions for both domestic and international customers. Refer to “External Power” for detailed power specifications for users who wish
Philips ADAT-4, ADAT-4 ADAT-4 User Guide Page 3 About the ADAT-4 The SoundPals ADAT-4 is an ADAT-to-AES converter that separates a single 8-channel ADAT data stream on optical fiber into four AES output audio pairs, on either balanced or coaxial cable. AES outputs are synchronous with the ADAT input. The unit offers the following features: • Synchronizing connector for a silent AES3id or word clock output. This output can be used to synchronize other SoundPals to the ADAT data stream. • Front panel switch for selecting reference output • Optional rack mou
Philips ADAT-4, ADAT-4 User Guide Page 4 The figure below illustrates the ADAT-4’s rear panel: AES OUT 1 AES OUT 2 AES OUT 3 AES OUT 4 MODEL A MADE IN THE USA 31 200mA +6V 2 4 5 6 1) ADAT-4 Model— the “A” model has AES3 outputs (XLR), and the “B” model has AES3id outputs (BNC). 2) Power Connector — accepts the power jack from the 6 VDC power supply. Refer to “External Power” for more information regarding external power. 3) AES OUT 1 — output #1 is standard AES audio, either AES
Philips ADAT-4, ADAT-4 User Guide Page 5 ADAT-4 Operation This section includes instructions for operating the ADAT-4. See the “ADAT-4 Specifications” section for a channel routing table. Operating procedures for the ADAT-4 are simple: • Connect the ADAT input from the desired ADAT source. • Connect AES outputs to the desired destinations. • If you want to use the ADAT-4 as the reference for another device, connect the SYNC OUT connector to the reference input of the destination device, and use the Sync Switch to select either AES or word clock reference. ADAT-4 Interconnection This section provides two ADAT-4 interconnection diagrams. �
Philips ADAT-4, ADAT-4 User Guide Page 6 • ADAT Bridge to AES Routing System In this application, the ADAT-3 and ADAT-4 combine to provide a bridge in and out of an AES routing switcher. ~ The ADAT-4 accepts an optical input from a source ADAT device (such as a workstation or ADAT recorder), and provides four AES outputs that feed the routing switcher. ~ The ADAT-3 accepts four AES inputs from the routing switcher, and provides an optical ADAT output for routing to ADAT destinations. Facility AES Routing
ADAT-4 User Guide Page 7 ADAT-4 Internal Jumpers This section provides information about the ADAT-4’s internal jumpers and switches. NOTE For detailed instructions on opening and closing the ADAT-4, see “Inside the Module.” The figure below shows the ADAT-4’s internal jumper locations: 20/24 Bit Jum p er Word Clock Polarit y Jum p er ADAT-4 04-0236- GRA
ADAT-4 User Guide Page 8 SW2 is the Status Dip Switch which is used to set the channel status on all AES outputs, including the SYNC output (provided that the Sync Switch is set to AES). The switch is an eight- position DIP, of which five switches are active. 12345678 OPEN 1 (closed) top position 0 (open) bottom position For all switches: ~ 0 is op
Philips ADAT-4, ADAT-4 User Guide Page 9 ADAT-4 Troubleshooting The table below lists ADAT-4 problems and solutions. Problem Procedure No output. • Check Power by Green LED. Outputs are all silent. • Check Input ERROR LED. • Verify that the source is not silent. Input ERROR. • Unplug the fiber cable and check for visible red light (this is not harmful). • If no light, unplug the cable from the source and check for visible red light from the transmitter. • Check for possible break in the fiber. NOTE Please contact the GPS factory if the problem still exists after completing the above procedures. ADAT-4 Specifications This section provides au
Philips ADAT-4, ADAT-4 User Guide Page 10 Audio Specifications (continued) AES3ID Synchronization Output Amplitude 1 ±0.2 V p-p Rise time 37 ±7 ns Output impedance 75Ω Return loss >15 dB (0.1–6 MHz) DC on output <50 mV Word Clock Synchronization Output Amplitude V LO <0.5 V at I OUT = -5 mA V HI >4.5V at I OUT = 5 mA Waveform Square-wave at Fs Phasing + edge coincident with audio sampling instant. Use jumper J5 to invert. Options RT-2, 1RU rack tray for mounting up to 3 units Power supplies: PSU-1, 90-260V 50/60Hz in-line power supply with detachable IEC power cord NOTE All specifications listed above subject to
Philips ADAT-4, ADAT-4 User Guide Page 11 Inside the Module In This Section This section provides instructions for opening and closing the SoundPals SDDM-8 module to gain access to the internal circuit board. NOTE The internal circuit board should only be removed from the module if you want to change the jumpers. Before You Begin Check the following items before opening the module and attempting to remove the internal circuit board: If required, remove the SoundPals module from the rack tray. Disconnect the power supply from the front of the product. Disconnect all input, output and control cables. Perform the rem
Philips ADAT-4, ADAT-4 User Guide Page 12 External Power About Power Supplies An external power supply conforming to the specifications listed in the following “Power Supply Specifications” section must be used to guarantee that published SoundPals performance figures are met. Any power supply meeting these specifications will supply adequate power for a single SoundPals module. Although the specification is written for power supplies running from AC line inputs, DC (battery) sources may be used if they meet all
Philips LR03PB2A Power Supply Specifications
LR03PB2A |
Philips LR6PS12C Power Supply Specifications
LR6PS12C |
Philips 6F22 Power Supply Specifications
6F22 |
Philips Power Life 9VPS4A Power Supply Specifications
Power Life 9VPS4A |
Philips LR14PB2C Power Supply Specifications
LR14PB2C |
Philips 6LR61 Power Supply Specifications
6LR61 |
Philips LR20EB4A Power Supply Specifications
LR20EB4A |
Philips SCP5150 Power Supply Specifications
SCP5150 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Anchor | BEACON BEA-6000 | Specifications | anchor/beacon-bea-6000-K6K.pdf | 11 Jul 2022 | 2 | 0.63 Mb |
2 | Lasko | 6050 | Operating manual | lasko/6050-8TT.pdf | 22 Dec 2023 | 4 | |
3 | Dimplex | AC3CN | Operation & user’s manual | dimplex/ac3cn-89L.pdf | 28 Jul 2022 | 8 | 0.95 Mb |
4 | Brother | QL-1100 | Quick setup manual | brother/ql-1100-R7W.pdf | 17 Aug 2022 | 8 | |
5 | True | bike MC | Owner's manual | true/bike-mc-6YG.pdf | 22 Mar 2023 | 21 | |
6 | Brother | LK3-B432 | Parts manual | brother/lk3-b432-5Y7.pdf | 13 Nov 2022 | 24 | 1.32 Mb |
ADTRAN
TOTAL ACCESS®MX2800 POWER SUPPLY UNITJOBAIDPSUCLEI: L1 M3PQ0A4B_ _L2 M3PQ0A5B_ _DESCRIPTIONThe MX2800 Power Supply Unit (PSU) is a plug-in unit for the MX2800 chassis that provides the necessary voltages required to operate the MX2800 and accessories such asthe fan faceplate. The DC version is P/N 1202289L2 and the AC version is P/N1202289L1. With two c …
MX2800(1 pages) |
Varian
PRE-INSTALLATION MANUAL CP-4900 Micro-GC PRO North/South America 2700 Mitchell Drive Walnut Creek 94598 California, USA Tel: ++(1)9259392400 Fax: ++(1)9259452360 or ++(1)9259452344 Europe P.O. Box 8033 4330 EA Middelburg The Netherlands Tel: ++(31)118671000 Fax: ++(31)118623193 Australia/East Asia 679 Springvale Road Mulgrave, Vi …
CP-4900 Micro-GC(7 pages) |
EFOY
1. Table of Contents 2 1. Table of Contents 1. Table of Contents 2 2. Introduction 4 2.1 Foreword 4 2.2 Safety Information 5 2.3 Safety notice for methanol cartridges 7 2.4 Normal Operation 7 2.5 Declaration of Conformity 8 2.6 Seals of Approval 8 2.7 Warranty 9 2.8 Disposal 10 3. Configuration 11 3.1 Standard Equipment 11 3.2 Overv …
EFOY Pro 600(54 pages) |
Puls
1 EN Instruction Manual DC/DC Converter 2 DE Bedienungsanleitung DC/DC-Wandler 3 FR Manual d'instructions Convertisseur DC/DC 4 ES Manual de instrucciones Convertidores DC/DC 5 IT Manuale di Istruzione Convertitore DC/DC 6 PT Manual de Instruções Conversor DC/DC CD-Serie Read this first! English 1 Before operating this unit …
CD5.121(4 pages) |
Tripp Lite
Owner’s ManualPDU6K Power Distribution Unit (PDU)for select UPS SystemsDesigned for 2U rack and other mounting optionsIMPORTANT SAFETY INSTRUCTIONS. This manual contains information concerning the proper installation and use of Tripp Lite’s Power DistributionUnits (PDUs). SAVE THESE INSTRUCTIONS.Note: This PDU is intended only for use with select Tripp L …
Power Distribution Unit (PDU) PDU6K(2 pages) |
DuraComm
1 of 4 August 24, 2016 HE1U-2548 High Efficiency 1U AC to DC Power Supply Owners Guide (These instructions are intended for use by a technician familiar with electronic products) Autorange Input Voltage 90 to 264 VAC DC-OK TTL Signal for each Module Short Circuit / Overload / Over Voltage / Over Temperature Protection 3 year warra …
HE1U-2548(4 pages) |
Lenovo Desktop ThinkCentre A52Lenovo Desktop ThinkCentre A52 Quick reference manual ThinkCentre A52, 92 |
Samsung Flat Panel TV LN40A500T1FSamsung Product User Guide: LN40A500T1F PDF Operation & user’s manual - 739JIT LN40A500T1F, 85 |
Fujitsu Tablet A1130 - Lifebook T6500 4GB 500GBGuide: Fujitsu A1130 - Lifebook T6500 4GB 500GB (IT3H7D, Upd.21st Aug 2023) A1130 - Lifebook T6500 4GB 500GB, 24 |
PRESIDENT Automobile Accessories MPB - 8800MPB - 8800 (Automobile Accessories ePDF Guide, #QFQ4LU) MPB - 8800, 20 |
TOTALINE Air Conditioner TOC009DSTOTALINE Air Conditioner TOC009DS Owner's manual TOC009DS, 36 |
Sony Receiver STR-VX250Guide: Sony STR-VX250 (XMA1R8, Upd.27th Sep 2023) STR-VX250, 15 |
Omron Blood Pressure Monitor IA1BOmron IA1B Blood Pressure Monitor Instruction manual IA1B, 26 |
Kramer Switch VP-734Kramer Product Manual: VP-734 PDF Operation & user’s manual - 7MY4VL VP-734, 83 |
Danfoss Thermostat RET2000 BOperation & user’s manual for Danfoss RET2000 B Thermostat RET2000 B, 12 |
Ricon Lifting Systems Mirage F10X SeriesRicon Lifting Systems Mirage F10X Series Service manual Mirage F10X Series, 6 |
Bacharach Software FyriteBacharach Fyrite User Guide (Doc Type: Software User software installation manual) Fyrite, 12 |
VALERA Other BSR 150VALERA BSR 150 Other Datasheet BSR 150, 2 |