Manualios.com

Horizon Hobby JR DSM 12x Instruction And Programming Manual

Horizon Hobby JR DSM 12x Manual Online:

3.4, 1519 votes
Horizon Hobby JR DSM 12x User Manual
Horizon Hobby JR DSM 12x User Guide
Horizon Hobby JR DSM 12x Online Manual

Text of Horizon Hobby JR DSM 12x User Guide:

  • A-32 Three dual and exponential rates are available and are selectable via flight modes or selected switches. 1. Highlight and select D/R & EXP in the FUNC.LIST to obtain the Dual Rate and Exponential display. 2. Highlight and select the desired channel (Aileron, Elevator or Rudder), noting that 3 sets of values will be displayed for each channel –

  • Horizon Hobby JR DSM 12x, A-44 The 12X features a three-position Flap System with Elevator compensation, programmable Delay, and an Auto Land feature. Its purpose is to allow the flaps to be programmed to three different positions, normally full flap, half flap and no flap or fully retracted position. Note: The Flap System is available in the FUNC.LIST only if SYS. is selected on the OUT line next to FLAP in the Device. Select function in the SYSTEM Menu. Because flaps generally causes a change in pitch (Elevator trim), the Flap System provides for setting a

  • Horizon Hobby JR DSM 12x, I-12 JR’s 12X offers airplane, helicopter and sailplane pilots the highest level of sophisticated programming features combined with the benefits of Spektrum’s 2.4GHz DSM ® radio link technology. DSM (Digital Spektrum Modulation) technology offers a far superior RF link over narrow band systems, providing a higher level of confidence and safety. Now with even the most sophisticated models you’ll no longer have to wait for an open frequency, worry about someone • Backlit screen • Ergonomic magnesium case • Digital 3 + 1 trims (3 digita

  • Horizon Hobby JR DSM 12x, H-14 The Stick Position Switch function allows the throttle, aileron elevator or rudder stick positions to be preprogrammed to turn on/off mixes or the timer. Four stick position programs are available and one or more can be assigned to various mixes or functions. The stick position that turns the Stick Position switch on/off is selectable as well as the direction to turn on/off. Also a symmetrical option is available that allows the function to be turned on with a preprogrammed equal right or left (up or down) stick

  • Horizon Hobby JR DSM 12x, H-1 The 12X Heli Mode programming is designed for model helicopters and includes 6 swashplate types making it compatible with virtually every type of helicopter. The 12X Heli program contains a host of sophisticated features. These features include: • Switch Assignability for channels and functions • 50-model memory • Up to six fully programmable Flight Modes • Flight Mode Naming allows custom naming of each flight mode. • Warning system allows custom programming of alarms for various switch and sti

  • Horizon Hobby JR DSM 12x, H-32 18: Throttle Curves The 12X offers up to five (5) separate throttle curves with up to eight adjustable points per curve. This function allows you to customize the throttle curve to maximize engine performance at any particular pitch setting. Once the throttle curves are established, each can be activated in flight using the 3-position flight mode switch. If the additional 2 flight modes (numbers 3 and 4) have been activated in the Device Select portion of the system mode, an additional switch will be used to activate these modes and two additional throttle curve

  • Horizon Hobby JR DSM 12x, A-16 The Flight Mode Name program allows each flight mode to be custom named with up to six characters. On the main screen an abbreviated (short name of up to four characters) will be automatically displayed when that flight mode is selected. Examples for flight mode names may include 3DRATE, LAND, ROLLER, etc. 1. In the SYSTEM MODE, highlight and select FM Name using the Selector. 2. Highlight the desired flight mode character position using the roller, then press the roller to access the list of

  • H-17 1. With the other end of the trainer cord plugged into the sending 12X transmitter in SYSTEM List as described in step 1 above, highlight and select TRANSFER (code 86) in the SYSTEM Menu to obtain the Transfer display. 3. The model to be transferred must be the currently selected model. If the model to be transferred is not currently selected, see Model SEL in the SYSTEM Menu to

  • Horizon Hobby JR DSM 12x, H-2 Pilots that have previous experience programming JR radios may feel confident programming the 12X without referring to the manual. Many of the functions and programming features operate similarly to JR’s 9303 and 10X radios. The Heli section Heli Programming of the manual is presented in the same order as the functions appear in the transmitter beginning with the System Menu functions and then the Function Menu functions. Flight Mode Switch Antenna Elevator D/R Switch Power Switch AUX 5 Knob Throttle Trim Aileron/Elevator Stick Mix Switch Handle Flap/Mix Switch Throttle/Rudder Stick Rudder D/R Switch Elevator Trim Rolling

  • Horizon Hobby JR DSM 12x, H-7 Model Copy Making a backup copy of the model memory protects against losing the original program and also allows one to experiment with the original program, knowing that the original settings can be restored by copying the backup copy back to the original model memory. To Copy a Model to Another Internal Memory 1. In the System MODE, highlight and select Model SEL using the rolling Selector. 2. Use the rolling Selector to highlight Select then press the roller to access model select. 3. Rotate the roller to select the desired model memory that you wish to copy the current program to. (1-50) 4. Press the roller to select the highlighted model that you wish

  • Horizon Hobby JR DSM 12x, H-9 Type select allows the model type to be selected. Model types include HELI (helicopter), ACRO (airplane) and GLID (glider). Note: When changing model types, the programming information will be reset to the factory default setting losing the previous settings. 1. In the System Menu, highlight and select Type SEL using the Selector. 2. Highlight and select HELI using the Selector and press the selector to access the HELI mode. 3. Return to the System Menu by pressing the LIST button. 89: Type Select To Select a Model Type

  • Horizon Hobby JR DSM 12x, W-3 Three Year Warranty Period Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship for a period of 3 years from the date of purchase by the Purchaser. Limited Warranty (a) This warranty is limited to the original Purchaser (“Purchaser”) and is not transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those Products purchased from an authorized Horizon dealer. Third party

  • Horizon Hobby JR DSM 12x, A-18 Preparing the 12X to Send a Model Transfer 1. With the other end of the trainer cord plugged into the sending 12X transmitter in SYSTEM List as described in step 1 above, highlight and select TRANSFER (code 86) in the SYSTEM Menu to obtain the Transfer display. 2. The model to be transferred must be the currently selected model. If the model to be transferred is not currently selected, see Model SEL in the SYSTEM Menu to select the model to be transferred. 3. When the receiving 12X is ready, press START on the left side of the display. The data for the currently selected mod

  • Horizon Hobby JR DSM 12x, A-19 The Warning function can be programmed to sound an alarm if a selected flight mode, switch positions or throttle stick position is in an inappropriate position when the transmitter is turned on. For example if the gear switch is in the retraced position and the transmitter is turned on, an alarm can sound warning that the switch will cause the gear to retract if the receiver is turned on. Or if the throttle is above a preprogrammed position when the transmitter is turned on an alarm will sound warning of an unsafe throttl

  • Horizon Hobby JR DSM 12x, S-3 Battery Door AUX 7 Knob Handle Left Lever Aileron Spring Tension Cover AUX 6 Knob Trainer/Transfer/PC Interface Jack Right Lever Elevator Spring Tension Cover Rudder D/R Charge Jack Throttle Spring Tension Cover Rudder Spring Tension Cover Bind/Range Check Button

  • Horizon Hobby JR DSM 12x, A-26 The 12X provides the ability to change the standard default switch assignments for the GEAR, FLAP, AUX2, AUX3, AUX4, AUX5, AUX6, and AUX7 channels. Changing the switch assignments is a matter of preference. The standard switch assignments may be changed in the Devic.SEL function contained in the SYSTEM MODE. 1. In the Devic.SEL function, use the Selector to highlight and select the desired channel to the right of GEAR, FLAP, AUX2, AUX3, AUX4, AUX5, AUX6 or AUX7. Switch Assignments To Change One or More Switch Assignments: The 12X provides

  • S-29 25: Camber System The Camber system allows preset camber adjustments for each programmed flight mode for the right and left ailerons, the right and left flaps, and if activated the right and left tip ailerons. The camber system allows for adjustments to the preset camber setting for each flight mode that is automatically selected with each flight mode. A Delay function

  • H-46 The slave channel is the secondary receiving channel and will move according to the program mix in relation to the master channel. The default for both the master and the slave channels is THRO. The slave channel is selected by highlighting and selecting this parameter to obtain a list of channels and then selecting the slave channel from the list. The li

  • Horizon Hobby JR DSM 12x, S-11 The 12X MV version radio system allows the RF module to be replaced allowing the system to operate on 72MHz or 2.4GHz. Note that the transmitter automatically detects which module is installed and modifies the accessible programming appropriate to the module selected. The Frequency Select function allows the selection of 72MHz channels 11 thru 60 when the 72MHz module is installed. This screen displays the channel and corresponding frequency. 93: Frequency Select- (12X MV system only) Note: This function is only available on the 12X MV version and only when the TSM-72A 72MHz module is plugged in. Important: When the 72MHz

  • Horizon Hobby JR DSM 12x, A-54 Aileron-to-Flap mix causes the flaps to move in unison with the ailerons. This function gives added roll response by mixing ailerons to flaps such that the entire trailing edge functions as an aileron. Note: This function is only available when Dual Flap is assigned in the Wing Type function. To access Aileron-to-Flap mix, in FUNC.LIST rotate the Selector until AILFLP M is highlighted. Press the Selector to access the Aileron-to-Flap mix. Note: Two Aileron-to-Flap mix values are available—Pos0 and Pos1. Switches are available at

  • Horizon Hobby JR DSM 12x, A-1 The ACRO mode is intended for powered fixed-wing aircraft. It contains a host of advanced features that are designed to assist the pilot in realizing the full potential of the aircraft. These features include: • Up to 5 flight modes • Switch and lever assignability • Triple Rates and Exponentials for Aileron, Elevator and Rudder that can be combined or assigned to flight modes • 4 programmable Wing Types (Normal, Flaperon, Delta, 4-aileron) • Aileron Differential with two values • V-Tail mixing • Dual Channels for All Primary Flight Controls and Flaps • Du

  • Horizon Hobby JR DSM 12x, S-28 24: Servo Speed To Adjust Servo Speed The 12X provides the ability to adjust the speed of servos for each channel in each direction. The speed may be reduced (servo slowed) from its normal speed but it cannot cause a servo to move faster than its rated specifications. Each servo can have 2 sets of speeds in each direction that are Flight Mode or switch selectable. 1. Highlight and select SRV. Speed. Speed FUNC.LIST. 2. If flight modes are not programmed, select SW SEL and press the roller to access Switc

  • I-14 Transmitter/Receiver Note: It is imperative that you fully charge both the transmitter and the receiver battery packs prior to each flying session and that you check the condition of the receiver battery between each flight using a reliable battery tester with a built-in load. The included wall charger charges at a 250mA rate. In order to fully charge the includ

  • Horizon Hobby JR DSM 12x, H-10 Note: This function is only available on the 12X MV version and only when the TSM-72A 72MHz module is plugged in. Important: When the 72MHz module is plugged in and the system is turned on, the antenna must be attached. Operating the 72MHz module without the antenna attached could overload the internal transistor causing a failure. Warning: Only the JR TSM-72A and JRM2.4 modules are compatible with the 12X MV. Do not install a standard- type JR, Spektrum or other branded module in the 12X as damage will occur. The 12X MV version radio system allows the RF module to be replaced allowing the system to operate on 72MHz or 2.4GHz. Note that the trans

  • Horizon Hobby JR DSM 12x, H-53 78: Trainer The 12X features a programmable Trainer System that allows the instructor to transfer some or all of the primary flight control functions (Throttle, Aileron, Elevator and Rudder) to the student. It also allows for indicating if the transmitter is to be the master (controlled by the instructor) or slave (controlled by the student). The right or left trim lever is used to transfer control to the student when the 12X is being used as the master/instructor transmitter. All Dual and Expo rates, Gear and flap positions are controlled by the master transmitter. Only the Throttle, Aileron, Elevator and R

  • Horizon Hobby JR DSM 12x, H-36 The 12X offers three different types of Gyro Gain Sensitivity Adjustments: manual, flight mode or automatic. This feature gives the user the choice of selecting gyro sensitivity through the rudder, aileron or elevator dual rate switches (manual), selecting one of three available gain settings for each flight mode (FOMD) or automatically selecting a gain for each flight mode (up to 6 gain settings). The gyro program can be set up for normal or tail lock gyros. In tail lock mode the value correlates with the actual percentage of the gyro output. A time lag featur

  • Horizon Hobby JR DSM 12x, A-39 The 12X features a Gyro Gain system that allows in-flight selection of 3 gyro gain settings for up to two separate gyros or up to five gyro gain settings assigned to flight modes. The system provides for fixed gain values and has settings for normal or tail lock gyros. Gyro gains can be assigned and selected via a three-position switch or with Flight Modes. Note: If one set of gains for a gyro is set to 0%, (in normal gain mode)then the gyro can be switched off during flight. Note: In order for the GYRO System to appear in the FUNC.LIST, the AUX2 and/or the AUX3 channels must be set to

  • Horizon Hobby JR DSM 12x, I-10 Master Channel - (Std. Prog Mixer) .........................................................................................................S-38 Slave Channel - (Std. Prog Mixer) ............................................................................................................S-39 Switch Position ........................................................................................................................................S-39 Offset ........................................................................................................................................................S-39 Mix Values ..........................................

  • Horizon Hobby JR DSM 12x, H-16 The TRANSFER function allows one 12X transmitter to transfer a model memory for a specific model to another 12X transmitter. This function is also used to transfer a model memory to the included PC date transfer allowing unlimited model memory storage and backup of your model’s programming. (See page H-16 for details on using the PC data transfer.) The Transfer function is also used to receive data from another 12X or from the PC Data Transfer. Note: The sending and receiving transmitters must

  • S-26 15: Sub Trim Use Sub Trims to fine-tune the output alignment of the servo arms. To Program Sub Trim Values 1. Highlight and select Sub Trim in the FUNC.LIST to obtain the Sub Trim Display. 2. Highlight and select the channels where the sub trims must be adjusted. Once a channel is selected, rotate the Selector until the servo arm is in the desired position. Note: This

Related Products and Documents (Radio):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Lanzar Vibe VW104 Specifications lanzar/vibe-vw104-GDO.pdf 16 Mar 2024 1
2 Electrolux EOC69611 Operation & user’s manual electrolux/eoc69611-4KM.pdf 19 Jun 2022 80
3 SR Suntour Electric bicycle Owner's manual sr-suntour/electric-bicycle-3QT.pdf 11 Mar 2023 42
4 UNICOM SmartGST-2402M Operation & user’s manual unicom/smartgst-2402m-Z4A.pdf 07 Aug 2022 82 4.21 Mb
5 Tapco SQ2 Owner's manual tapco/sq2-275.pdf 03 Sep 2022 20 0.87 Mb
6 Zenith A50M84W Operating manual zenith/a50m84w-9N2.pdf 30 Apr 2023 52 2.34 Mb

Similar Resources:

  • iHome

    iPL22

    (16 pages)
    Model: iPL22Instruction manual - US EnglishSize: 102 x 150 mmDate: Jan 7, 2014Mat’l: 100gsm paper (WF)Color: Black text on white backgroundCoverWarrantyModel iPL22FM clock radio withcharge + play for iPhone or iPodQUESTIONS? Visit www.ihome.comFCC InformationThis device complies with Part 15 of the FCC Rules, operation is subject to the following two condi …
  • Philips

    AJ-5030

    (2 pages)
    PhilipsClock RadioTime projectionAJ5030Wake up and beamwith a time projectionEnjoy the convenience of time shone onto any surface you like. Sharpen the image or flip it, so it is always clear and readable on a wall or ceiling. This clock also automatically sets the time and offers melody, radio or buzzer as alarm options.Time projection with a style• Fle …
  • Sony

    ICF-C113

    (19 pages)
    MICROFILMICF-C113/C113L/C113VSERVICE MANUALICF-C113FM/AM PLL SYNTHESIZED CLOCK RADIOICF-C113LFM/MW/LW PLL SYNTHESIZED CLOCK RADIOICF-C113VTV/WEATER/FM/AM PLL SYNTHESIZED CLOCK RADIOSPECIFICATIONSUS ModelICF-C113VE ModelAustralian ModelICF-C113UK ModelICF-C113LAEP ModelICF-C113/C113LTime display :US, UK, Australian model 12hourEXCEPT US, UK, Australian model …
  • Philips

    AE6775/20Z

    (2 pages)
    ENGLISHPOWER SUPPLYBattery (not included)• Open battery door and insert two alkaline batteries, type R03,UM4 orAAA as indicated. • Remove the batteries from the set if they are exhausted or not to be usedfor a long time.– When the batteries are running low, flashes in the display. If theradio is on, it will automatically switch off.– It may be necess …
  • SOUNDMASTER

    NR920

    (5 pages)
    DEUTSCH ITALANIO ENGLISH NORSK FRANÇAIS SVENSK NEDERLANDS NR920 Hersteller Wörlein GmbH Tel.: +49 9103/71670 Gewerbestrasse 12 Fax.: +49 9103/716712 D 90556 Cadolzburg Email. [email protected] GERMANY Web: ww …
  • Daktronics

    FLR3-400

    (4 pages)
    FLR3-400 Installation Quick Guide Page 1 of 4DD2239290 Rev 036 August 2014PO Box 5128 201 Daktronics Drive, Brookings, SD 57006-5128tel: 800-325-8766 fax: 605-697-4700www.daktronics.comThis quick guide provides steps for installing the receiver and setting up a FLR3-400 key fob with a FuelightTM Gen 3 display.Installing the Receiver1. Using a flat-head scr …

Comments, Questions and Opinions: