Horizon Hobby Venture50 Assembly Instructions Manual

Text of Horizon Hobby Venture50 User Guide:

• Horizon Hobby Venture50, 51 Flight Training Flight Simulators A model helicopter simulator is highly recommended and is an excellent training aid. Simulators like the CSM V10 will help you learn the orientation and inputs needed to fly a model helicopter, without the risk of damaging your model to learn these same reactions. In general, most beginning pilots find that using an RC simulator prior to their first actual flights with their model increase the speed in which they learn, and also decrease the number of crashes associated with learning to fly. Even the most experienc

• Horizon Hobby Venture50, 21 The following activation and setup procedure should be used for all JR XP8103 and XP8103DT (digital trim) systems. Note: Some early XP8103 systems will require the activation of the CCPM software through the Horizon Service Center. It’s easy to identify if your system has the CCPM function activated by identifying if the “SWASH TYP” function appears in the System mode as shown in Section A below. Please refer to Section A to access the System mode. Prior to activating the CCPM function, it is first suggested that the Data Reset function be performed to reset the desired model number to be used back to the factory default settings. If you a

• 62 4-3 MAIN BLADE HOLDER ASSEMBLY 3x6 mm Self-Tapping Screw (4) 2x10 mm Flat Head Screw (2) 3x5 mm Set Screw (2) Joint Ball (2) 3x8 mm Socket Head Bolt (4) Phase Ring Pins (2) 5x10x4 Thrust Bearing (2) 5x13x4 Bearing (4) 5x9x1 Spacer (2) 8x13x1 Spacer (2) Phase Ring Pins (2) 3x8 mm Socket Head Bolt (4) Joint Ball (2) 2x10 mm Flat Head Screw (2) 5x13x4 Bearing (4) Main Blad

• Horizon Hobby Venture50, 43 XP8103 HELI DATA SHEET VENTURE 50 3D BASIC SETUP EXP L 1 2 3 H N OFF•ON 0% 30% 50% 70% 100% 1 OFF•ON 40% 50% 60% 80% 100% 2 OFF•ON N OFF•ON -2° pitch % 5° pitch % 10° pitch 1 OFF•ON -5° pitch % 5° pitch % 10° pitch 2 OFF•ON % % % %% H OFF•ON -5° pitch % 5° pitch % 13° pitch 1 MODEL NO. ____________________________________ MODEL NAME __________________________________ MODULATION SPCM - ZPCM - PPM ________________ AILE ELEV RUDD D/R 90% 90% 90% EXP D/R 100% 100% 100% EXP 0 0 80% 60% Set for idle Adjust as needed POS OFFSET REV

• Horizon Hobby Venture50, 4-4 WASHOUT ASSEMBLY 4-5 SWASHPLATE ASSEMBLY 63 Swashplate Adjustment The 120° CCPM swashplate is adjustable via the 3–4x4 mm set screws. If excessive play is found in the test above, gently tighten each of the 3–4 mm set screws the same amount and re-test. The swashplate should move freely, but without notable play. Caution: If the 3–4 mm set screws are over tightened, damage to the swashplate bearings can occur. While holding the inside ball race, pivot the swashplate and check for excessive pla

• Horizon Hobby Venture50, ADDITIONAL ITEMS REQUIRED TO COMPLETE THE VENTURE 30CP 1. RADIO SYSTEM REQUIREMENTS (NOT INCLUDED): 6-channel or greater R/C helicopter system with 120° CCPM function (see list below), 5 servos, 1000mAh receiver battery, and gyro VENTURE ™ 50 3D ARF FEATURES CCPM (Cyclic/Collective Pitch Mixing): More Accurate: Control system play is totally eliminated thanks to full ball bearings and a high-grade swashplate Simpler: Fewer links to set up and maintain More Powerful: Collective has three times the servo power, cyclic has double Special 3D Rotor Head Design The Venture 50's updated 3D rotor head features an aluminum center hub, heavy duty spindle shaft, 3D dampen

• Horizon Hobby Venture50, 60 3-2 LANDING GEAR ASSEMBLY INSTALLATION 3x8 mm Socket Head Bolt 3x8 mm Socket Head Bolt (4) 3x12 mm Socket Head Bolt 3x4 mm Set Screw 3x4 mm Set Screw (4) 3 mm Flat Washer (4) 3x12 mm Socket Head Bolt 3 mm Flat Washer (4) Landing Gear Damper (4) Landing Skid (2) 40 mm Landing Strut (2) Position landing skids so they extend 40 mm past the rear landing strut. Rear Landing Strut

• Horizon Hobby Venture50, 19 JR 120° Three-Servo CCPM relies on the radio’s special CCPM swashplate mixing, rather than a conventional mechanical mixer that is utilized to achieve the same results. The radio’s 120° Three-Servo CCPM function automatically mixes the three servos to provide the correct mixing inputs for aileron (roll), elevator (pitch), and collective. The following is an example of how each control input affects the servo’s movement: 1. Collective When a collective pitch input is given, all three servos (A, B, and C) move together in the same direction, at equal amounts, to raise and lower the swashplate while keeping the swashplate level. During this function, all three servos travel at the s

• Horizon Hobby Venture50, 47 FINAL SERVO ADJUSTMENT AND RADIO SETUP Now that the radio system is completely installed into the helicopter, it is necessary to check and adjust the following: 1. Servo Direction (Servo Reversing) Check to insure that all servos have been set to the correct direction as shown in programming section, pages 20-22. 2. Dual Rates It is suggested that for initial flights the Dual Rate function values be set as follows: 0 Position (low rate): 90% 1 Position (high rate): 100% 3. Exponential Settings It is suggested that the exponential rate settings remain in the 0 value position until the initial test flights. After initia

• MAIN FRAME/DRIVE GEAR ASSEMBLY PARTS 75 PART # DESCRIPTION COMMENTS/ADDITIONAL CONTENTS QUANTITY JRP960850 Main Frame L/R Main Frame R 1 Main Frame L 1 JRP980068 3x15 mm Set Screw 3x15 mm Set Screw 10 JRP960232 Body Mounting Standoff L21 Body Mounting Standoff L21 2 JRP980013 3x8 mm Socket Head Bolt 3x8 mm Socket Head Bolt 10 JRP980039 3 mm Lock

• Horizon Hobby Venture50, 28 3-5 CCPM LINKAGE CONNECTION Attach the three CCPM servo linkages as shown below. It is important that the exact distances specified below be maintained for each linkage as this is critical to the alignment and neutral position of the swashplate. Please also note the direction of the ball links as shown by the “JR Propo” name imprinted on each ball link. “JR Propo” is imprinted on the front of each ball link. When attaching the control rods, it is important to make sure that “JR Propo” faces outward as the links are attache

• Horizon Hobby Venture50, 3-8 ADVANCED SETUP: PITCH-TO-ELEVATOR MIXING ADJUSTMENT WITH TRAVEL ADJUST (OPTIONAL) 31 The total travel of each servo can vary slightly, which can also cause the swashplate to be tilted fore and aft when the collective is moved to the extreme high and low pitch positions. This situation can also be corrected if necessary through the use of the Travel Adjustment function. To check pitch-to-elevator mixing, it will first be necessary to position the collective stick in the center position as in the previous steps. Next, move the collective stick from the center to the high pitch position while viewing the swashplate from

• Horizon Hobby Venture50, 38 4-5 OPTIONAL AGGRESSIVE 3D CONTROL SYSTEM SETUP C. 3D FLYBAR/PADDLE INSTALLATION Remove the current flybar and paddles by removing one paddle and loosening the two 4 mm flybar control arm screws. Install the special 410 mm 3D flybar and paddles as shown. Check to make sure that the flybar is centered before attaching the paddles. Thread the 3D paddles onto the flybar through the front hole in the paddles. It is not recommended that the paddles be used in the rear hole, as they will make the control overly aggresssive. Use Blue Threadlock Align paddles so they are parallel to each other and to the flybar cont

• Horizon Hobby Venture50, 4-8 ROTOR HEAD INSTALLATION 65 2.6x12 mmSocket Head Bolt (1) 3x20 mmSocket Head Bolt (1) 3 mm Flat Washer (1) 2x12 mm Flat Head Screw (2) 2x12 mm Flat Head Screw (2) Steel Joint Ball (2) Steel Joint Ball (2) Rotor Head Assembly 2 mm Hex Nut (2) 2 mm Hex Nut 2.6 mm Lock Nut (1) 2.6 mm Lock Nut 3 mm Lock Nut 3 mm Lock Nut (1) 3x20 mm Socket Head Bolt Note: Be sure to engage the rotor hub pin into the washout base groove before securing the rotor head in place. 2.6x12 mm Socket Head Bolt 3 mm Flat Washer (2) 4x4 mm Set Screw Flybar Center the flybar in the seesaw shaft before securing the flybar control arm.

• Horizon Hobby Venture50, 6 Needle-Nose Pliers Drill and Drill Bits Allen Wrenches: 1.5, 2.0, 2.5, 3.0 mm Ball Link Pliers JR Ball Link Sizing Tool (JRP960219) (optional) Universal Blade Balancer (KSJ528) Crankshaft Locking Tool (RVO1007) X-ACTO Knife Metric Ruler Scissors (DYN2511) 12-Volt Electric Starter (HAN110) 12-Volt Starting Battery (HAN102) Long Reach 1.5-Volt Glow Plug Battery (DYN1960) Long Reach Remote Glow Plug Adaptor (HAN121) Helicopter Fuel, 15%–30% Pitch Gauge (JRP960326) Fuel Pump (KSJ860) Hex Starting Sha

• Horizon Hobby Venture50, 7 Socket Head Bolt Tapping Screw Flat Washer .05mm .05mm Flat Head Screw Lock Nut There are many various sizes and shapes of hardware included in this kit. Prior to assembly, please be careful to identify each screw by matching it to the full size screw outlines included in each step. All of the hardware, screws, nuts, etc., contained in the Venture ™ kit are described in the following A, B, C manner: C C C A B A A B B C 3x8 mm Socket Head Bolt Set Screw C A B C C A A A 2x8 mm Flat Head Screw 2.6x10 mm Self-Tapping Screw A B B 3 mm Flat Washer A B B 3 mm Lock Nut Spring Washer A B B 3 mm Spring Washer A Hex Nut A B B 2 mm Hex Nut C 4x4 mm Set Screw HARDWARE IDE

• Horizon Hobby Venture50, ASSEMBLY INSTRUCTIONS VENTURE SPECIFICATIONS Overall Length 47.32'' Overall Height 16.29'' Main Rotor Diameter 52.63'' Tail Rotor Diameter 9.17'' Gear Ratio 9.78:1 : 5.18 Gross Weight 7.0–7.5 lb ARF ™

• Horizon Hobby Venture50, 3-3 CCPM SERVO ARM PREPARATION AND INSTALLATION 25 2x10 mm Flat Head Screw (3) Steel Joint Ball (3) 2 mm Hex Nut (3) It will be necessary to prepare three servo arms as shown in the diagram below. Prior to assembling the servo arms, the servos should be centered as indicated below, and the servo arms test fitted to the servo to insure that the arms will attach to the servo as indicated. Since the JR servo arm spline uses an odd number of teeth, it is sometimes possible to rotate the servo arm 180° to ach

• Horizon Hobby Venture50, 58 2-3 FRONT RADIO BED/COOLING FAN SHROUD INSTALLATION 3x10 mm Socket Head Bolt (4) 2.6x10 mm Self-Tapping Screw (4) 2.6x10 mm Self-Tapping Screw (4) Cooling Fan Shroud 3x10 mm Socket Head Bolt (4) Front Radio Bed

• 30 3-7 ADVANCED SETUP: PITCH-TO-AILERON MIXING ADJUSTMENT WITH TRAVEL ADJUST (OPTIONAL) It is very possible that the travel of each servo varies slightly, which can cause the swashplate to be tilted to the left or right when the collective is moved to the extreme high and low pitch positions. This condition is generally more common when standard type servos are used. If JR digital servos ar

• 4-1 FLYBAR CONTROL ARM/SEESAW ARM ASSEMBLY 4-2 SPINDLE SHAFT/DAMPNER ASSEMBLY 61 Center Yoke 3x15 mm Socket Head Bolt (2) 3 mm Flat Washer (4) 3x15 mm Socket Head Bolt (2) 2x10 mm Flat Head Screw (4) 2x12 mm Flat Head Screw (2) 3 mm Flat Washer (4) 2 mm Hex Nut (2) Joint Ball (6) 4x4 mm Set Screw (2) 4 mm Lock Nut (2) 4 mm Lock Nut (2) Spindle Shaft Damper Ru

• 40 Factory Preset Factory Preset XP662 HELI DATA SHEET VENTURE 50 3D SETUP D/R 90% 90% EXP Adjust as needed D/R 100% 100% EXP Adjust as needed TRIM OFFSET CHANNEL THR (1) AIL (2) ELE (3) RUD (4) GER (5) PITCH (6) NORM NORM NORM NORM NORM NORM ••••• • REV REV REV REV REV REV SUB-TRIM TRAVEL ADJU

• Horizon Hobby Venture50, 18 120 Three-Servo CCPM Swashplate Mixing (Venture 30 CP) The JR 120° CCPM or Cyclic/Collective Pitch Mixing, system offers the user a control system that can accomplish the same control inputs as the One-Servo standard system mentioned above, but with increased precision and reduced complexity. As with the One-Servo system, the JR CCPM system utilizes three servos for the three main controls: aileron (roll), elevator(pitch) and collective. The CCPM lower swashplate ring is designed with only three control balls, spaced at 120° from each other, hence the 120° CCPM designation. Although the control balls are not at 90° as in

• Horizon Hobby Venture50, 44 XP8103 HELI DATA SHEET VENTURE 50 3D SETUP EXP L 1 2 3 H N OFF•ON 0% 30% 50% 70% 100% 1 OFF•ON 100% 80% 50% 80% 100% 2 OFF•ON N OFF•ON -2° pitch % 5° pitch % 10° pitch 1 OFF•ON 10° pitch % 0° pitch % 10° pitch 2 OFF•ON % % % %% H OFF•ON -5° pitch % 5° pitch % 13° pitch 1 MODEL NO. ____________________________________ MODEL NAME __________________________________ MODULATION SPCM - ZPCM - PPM ________________ AILE ELEV RUDD D/R 90% 90% 90% EXP D/R 100% 100% 100% EXP 0 0 80% 60% Set for idle Adjust as needed POS OFFSET REVO MIX ACC MIX NORMAL NORM STNT HOLD INVT UP % DOWN % UP % DOWN % % GYRO SENS INH • RUDD D/R • AUTO STUNT PROGRAM MIX THROTTLE CURVE PITCH CURVE

• Horizon Hobby Venture50, 14 3-1 SERVO INSTALLATION RADIO INSTALLATION SUGGESTIONS Be sure to install four rubber servo grommets and eyelets to each servo prior to installation. When adjusting control rods, be sure to adjust each universal link the same amount so as not to unthread one link too far. Be sure to keep all servo lead wires, etc., away from all servo arms, rods, and sharp edges of the helicopter’s mechanics. After final installation, group these wires together as indicated using the small nylon wire ties and the nylon spiral tubing included with this kit. Note: It is sugge

• Horizon Hobby Venture50, 3-4 CCPM SERVO CENTERING WITH THE SUB-TRIM FUNCTION 27 JR PCM10, 10S, 10SX, 10SXII, 10X SYSTEMS 1) Enter the Sub-Trim function (Code 15). 2) Adjust the left (aileron), right (AUX 1) and front (elevator) servos as needed until the servo arm is exactly parallel to the servo as shown when the collective stick is in the center position. It will be necessary to press the Page button to access the right servo (AUX 1) sub-trim value. 3) Press Enter to exit the Sub-Trim function. XP8103, XP8103 WITH DIGTIAL TRIMS 1) With the radio power switch on, press the Up and Down keys simultane

• Horizon Hobby Venture50, 20 CCPM SOFTWARE ACTIVATION AND INITIAL ADJUSTMENT The following activation and setup procedure should be used for all JR XP652 and XP662 systems. Please note that the XF622 and XP642 6-channel systems do not have the required CCPM software and therefore cannot be activated by the Horizon Service Center. Prior to activating the CCPM function, it is first suggested that the Data Reset function be performed to reset the desired model number to be used back to the factory default settings. If you are using a new radio system, proceed to Step C. Caution: Prior to performin

• Horizon Hobby Venture50, CONTROL SYSTEM ASSEMBLY 72 960013 997168 980041 970002 994024 960425 980032 980135 980067 960009 970184 970010 981015 980016 997168 980044 980037 970002 980013 960848 997168 980042 970002 980037 970016 980013 980054 970002 980037 997168 960022 970002/980032 (3D)

Related Products and Documents (Toy):

Comparable Devices:

Similar Resources:

• Eduard Sturmtiger interior (5 pages) Sturmtiger interior35 9601/35 scale detail set for kit • sada detailů pro model 1/35REVELL REVELLORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍFILLTMELITeduardREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT OTVORAPPL …

• Topmodel SKY WING SLICK 360 (22 pages) ATTENTION !Ce modèle à construire n’est pas un jouet, ilne convient pas aux enfants de moins de 14 ans.Une mauvaise utilisation de ce matériel peutprovoquer des dommages matériels ou corporels. Vous êtes pleinement responsablelorsque vous utilisez votre modèle. Volez à une distance de sécurité des zones habitées.Soyez sûr que personne n’émet …

• NOCH 14398 (2 pages) NOCH GmbH & Co. KG - Lindauer Straße 49 - D-88239 Wangen im Allgäu - [email protected] - www.noch.de - Stand 04/2016 NOCH GmbH & Co. KG - Lindauer Straße 49 - D-88239 Wangen im Allgäu - [email protected] - www.noch.de - Stand 04/2016 Vor Gebrauch die Sicherheitshinweise und Anleitung genau lesen und beachten. Bei diesem Produkt handelt es sich um e …

• Eduard Stug.IV (2 pages) TP065Stug.IVTP0651/2ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍFILLTMELITeduard1/35 scale detail set for kit •sada detailù pro model 1/35ITALERI ITALERIREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT OTVORAPPLY EX …

• Laser Pegs 1290 (6 pages) Please read this manual before you begin! Failure to follow this manual’s instructions may result in damage to the Triangle Power Base, AC Adapter and/or Laser Pegs®. Not adhering to these instructions will void the manufacturer’s warranty. The packaging must be kept because it contains important information.This manual is copyright and cannot be repro …

• Eduard Spitfire Mk.VIII (12 pages) UPOZORNENÍ ACHTUNG ATTENTIONATTENTIONINSTRUKTION SINNBILDEN INSTR. SYMBOLYSYMBOLES INSTRUCTION SIGNSPLASTIC PARTSOPTIONALFACULTATIFNACH BELIEBENVOLBABENDPLIER SIL VOUS PLAITBITTE BIEGENOHNOUTOPEN HOLEFAIRE UN TROUOFFNENVYVRTAT OTVORSYMETRICAL ASSEMBLYMONTAGE SYMÉTRIQUESYMMETRISCHE AUFBAUSYMETRICKÁ MONTÁŽ REMOVERETIRERENTFERNENODŘÍZNOUTREVERSE SIDEO …

Comments, Questions and Opinions: