HP Action Cam AC200 Operation & User’s Manual

Text of HP Action Cam AC200 User Guide:

• HP Action Cam AC200, 49 3. Secure the waterproof case lock. The waterproof case can be used with other accessories such as the swivel T tip, bike mount, chest mount, head mount, etc. 5.1.2 Changing the T Tip Adapter Depending on the accessories that you want to use with the case, the T tip adapter may be detached and attached to another housing back door or location. To detach the T tip adapter, remove the four screws securing each tip adapter to the case.

• HP Action Cam AC200, 35 9. To exit the menu, press the Mode button repeatedly until the EXIT screen appears. 10. Press the Shutter button to exit SET mode.  Note: Ultra and Wide are only available in Photo mode. The FOV for Video mode is always Ultra. 4.3 Shooting Interval This menu allows you to select the interval options when capturing photos using Lapse mode. Do the following to select the shooting interval. 1. Press the Mode button repeatedly to change to SET mode. 2. Press the Shutter button to enter SET mode. 3. Press the Mode button to highlight SETUP. 4. Pres

• HP Action Cam AC200, 55 General EV Compensation -2.0EV ~ +2.0EV (Auto) PC interface USB 2.0 (High Speed) TV out format HDMI Shutter speed Still: 1/30 ~ 1/4000 sec. Video: 1/30 ~ 1/2000 sec. Auto power off 1min / 3min / 5min / 10min / 30min / 60min / Off Power supply Rechargeable 1130 mAh Li-ion Battery Dimensions 42.7 (H) x 59.2 (W) x 26.4 (D) mm. (without lens) Weight Approx. 783g (without Waterproof Case)

• HP Action Cam AC200, 52 5.4 Wrist Strap Remote Control Before using the RF wrist strap remote control, you must pair it with the camcorder. Take note that only one camcorder can be paired to the RF wrist strap remote control at a time. Do the following to pair your RF wrist strap remote control. 1. On the camcorder, press the Mode button repeatedly to change to SET mode. 2. Press the Shutter button to enter SET mode. 3. Press the Shutter button to enter the MORE menu. 4. Press the Mode button to highlight BINDING. 5. Press the Shutter button to enter the BINDING submenu. 6. The camcorder RF antenna is enabled and ready to be paired with the RF wrist strap remote control

• HP Action Cam AC200, vi Precautions General precautions  Do not store the product in dusty, dirty, or sandy areas, as its components may be damaged.  Do not store the product in a hot environment. High temperatures can shorten the life of electronic devices, damage batteries and warp or melt certain plastics.  Do not store the product in cold areas. When the product warms up to its normal temperature, moisture can form inside, which may damage the electronic circuits.  Do not attempt to open the casing or attempt your own repairs. High-voltage internal components create the risk of electric shock when exposed.  Do not dr

• HP Action Cam AC200, iii 5.1.3 Changing the Housing Back Door ...............50 5.2 Velcro Strap .........................................................50 5.3 Assembling the Camcorder Accessories.............51 5.4 Wrist Strap Remote Control................................52 Appendix ............................................................ 54 Specifications.................................................................54 Troubleshooting.............................................................56

• HP Action Cam AC200, i Table of Contents Preface .............................................................................iv Precautions......................................................................vi Operating conditions.................................................vii Notes on Waterproof Case........................................... viii Before You Start............................................................. xi 1 Introducing the Camcorder....................... 12 1.1 System Requirements .........................................12 1.2 Features .................

• HP Action Cam AC200, 54 Appendix Specifications General Imaging sensor 1/2.5” CMOS 5.0 Megapixel Sensor Active pixels 5.0 Megapixel Storage media Internal: Built-in 128MB Flash Memory SD Card, SDHC compatible (up to SDHC 32GB Class6) Sensor sensitivity Auto Camera Optics Fixed lens Wide: F2.8, f=2.5mm 110°/1080p, 150°/720p, 162° in 960p, 165 in 5M Photo Focus range 30cm ~ infinity Still image Format: JPEG (EXIF 2.2), DCF Resolution: 5M Mode: Signal shot 10 Photo Burst, Time-Lapse (every 1, 3, 5, 10, 30, 60 sec) Movie clips Format: H.264 (AVI) Resolution: 1080p: 1920x1080 (30fps), 960p: 1280x960 (30fps),

• HP Action Cam AC200, 1 7 1.4 About the Camcorder Refer to the following illustrations to familiarize yourself with the buttons and controls of this camcorder. 1.4.1 Camcorder Views Powe r /Status LED 1 Lens Speaker HDMI port Shutter button Power/Status/B attery LED 2 Power / Mode button OLED screen microSD card slot Battery compartment cover Power/Status LED 4 Microphone jack Micro USB port Microphone Power/Status LED 3

• HP Action Cam AC200, 3 7 6. Press the Shutter button to enter the UP/DOWN submenu. 7. Press the Mode button to select ON or OFF. 8. Press the Shutter button to confirm. 9. To exit the menu, press the Mode button repeatedly until the EXIT screen appears. 10. Press the Shutter button to exit SET mode. 4.5 Delete This menu allows you to delete all files in the Micro SD card. Do the following to delete all files. 1. Press the Mode button repeatedly to change to SET mode. 2. Press the

• HP Action Cam AC200, 44 4.11 Date and Time This menu allows you to set the camcorder date and time settings. Do the following to set the camcorder date and time. 1. Press the Mode button repeatedly to change to SET mode. 2. Press the Shutter button to enter SET mode. 3. Press the Shutter button to enter the MORE menu. 4. Press the Mode button to highlight TIME. 5. Press the Shutter button to enter the TIME submenu. The Year is highlighted. 6. Press the Shutter button repeatedly to adjust the year. 7. When done, press the Mode button to go to the month field. Year Hour Minute Month Day 8. Press the Shutter button repeatedly to adjust the month

• HP Action Cam AC200, 19 1.4.3 LED Indicators The camcorder has four LED indicators. The Power/Status LEDs are located on top, on the bottom, and on the back of the camcorder. These LEDs are designed for users to see the status of the camcorder whichever way the camcorder is held or mounted. LED Color Description Green Power is on Green Blinking Taking photos Red Blinking Video recording in progress / RF remote control in progress Power / Status LED Red Blinking Rapidly Self-timer Red Blinkin

• 38 7. Press the Mode button repeatedly to scroll through the delete options. To delete the last captured video or photo. To delete all files in the micro SD card. To format the micro SD card. 8. Press the Shutter button to confirm. 9. Press the Mode button to select √ to confirm deletion. 10. Press the Shutter button to confirm. 11. To exit the menu, press t

• 46 6. The camcorder RF antenna is enabled and ready to be paired with the RF wrist strap remote control. 7. Press both the video and photo buttons on your RF wrist strap remote control to process pairing. When the red LED on the RF wrist strap remote control flash once, pairing is complete. 8. To exit the menu, press the Mode button re

• HP Action Cam AC200, 39 4.6 OSD Up/Down This menu allows you to display the OLED screen upside down. Do the following to enable this feature. 1. Press the Mode button repeatedly to change to SET mode. 2. Press the Shutter button to enter SET mode. 3. Press the Shutter button to enter the MORE menu. 4. Press the Shutter button to enter the UP/DOWN submenu. 5. Press the Mode button to select OSD UP or OSD DOWN. 6. Press the Shutter button to confirm. 7. To exit the menu, press the Mode button repeatedly until the EXIT screen appears. 8. Press the Shutter button to exit SET mode.

• HP Action Cam AC200, 45 10. Press the Shutter button repeatedly to adjust the hour value, and then press the Mode button to go to the minute field. 11. Press the Shutter button repeatedly to adjust the minute value, and then press the Mode button to highlight OK. 12. Press the Shutter button to complete the date and time setting. 13. To exit the menu, press the Mode button repeatedly until the EXIT screen appears. 14. Press the Shutter button to exit SET mode. 4.12 RF This menu allows you to pair your camcord

• 32 Up/Down Select to set the direction of the OSD screen display. LED Select to turn the LED on or off. Bright Select to adjust the screen brightness. Beep Select to adjust the beep volume. Auto-Off Select to set the time for the camcorder to automatically turn off when not in use. Time Select to set the camcorder date and time. RF Select to pair with the R

• HP Action Cam AC200, ix Notes for general use:  Avoid opening or closing the waterproof case near the water’s edge (sea, lake, beach, lake, etc.). Do not open or close the waterproof case lock with wet hands, or hands with sand or dust.  The accessories (batteries, etc.) used with the camcorder are not water resistant, be careful in using them.  Do not drop the waterproof case to ensure waterproof durability.  Do not place the waterproof case in temperatures above 45°C or below 0°C to ensure waterproof durability.  Do not attempt to make alterations on the waterproof case or seal the vents yourself, doing so may damage its waterproof ability. W

• 43 9. Press the Shutter button to exit SET mode. 4.10 Auto-Off This menu allows you to program the camcorder to automatically turn off after being idle for a specific period of time, or you can set the setting to OFF to keep the camcorder on until you manually turn it off. Do the following to select the auto-off option. 1. Press the Mode button repeatedly to chan

• 18 1.4.2 Button Functions Power / Mode Button  Press and hold for 3 seconds to turn the camcorder on or off.  Press to switch to different modes: Video, Photo, Burst, Time Lapse, Self-timer, and Set mode.  In Set mode, press to scroll through menu items. Shutter Button  In Video mode, press to start/stop video recording.  In Photo mode, press to take a

• HP Action Cam AC200, 26 Time Lapse Mode In this mode, photos are continuously captured with a specific interval time when the Shutter button is pressed. To stop capturing, press the Shutter button again. The icon also indicates the current capture settings. Self-timer Mode In this mode, photos are taken 10 seconds after pressing the Shutter button. The icon also indicates the current capture settings. 1 Set Mode Use this mode to adjust the settings of your camcorder. Button Function Indicates the operation that the camcorder will do when the Shutter button is pressed. The displayed icon varies depending on th

• HP Action Cam AC200, xi Before You Start Take some test shots before you use your camcorder. Before taking pictures with this camcorder, test the camcorder beforehand to ensure that it functions properly. Any additional loss caused by the malfunction of this product (such as costs of photography or any loss of benefit generated by the photography) is not the responsibility of the manufacturer and no compensation will be given for it. Copyright information Take care to observe "No Photography" notices in certain locations. In these cases, you cannot record any live perfor

• HP Action Cam AC200, 33 4.1 Video Resolution The HP ac200w captures photos with a fixed resolution of 5M and supports three resolution options for videos. Do the following to select the video resolution. 1. Press the Mode button repeatedly to change to SET mode. 2. Press the Shutter button to enter SET mode. 3. Press the Mode button to highlight SETUP. 4. Press the Shutter button to enter the SETUP menu. 5. Press the Shutter button to enter the VIDEO submenu. 6. Press the Mode button repeatedly to scroll through the resolution options. 16:9 Full HD Video, 1080P (1920x1080, 30fps) 4:3 Widest HD Video, 960P (1280x960, 30fps) 16:9 HD v

• HP Action Cam AC200, v Modifications: The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user's authority to operate the equipment. Trademark Recognition Windows XP/Vista/Windows 7/Windows 8 are registered trademarks of Microsoft Corporation in the United States and/or other countries. Macintosh and Mac OS are registered trademarks of Apple Inc. In addition, all other companies or product names are trademarks or registered trademarks of their respective companies. Radiation Exposure Statement

• HP Action Cam AC200, 50 5.1.3 Changing the Housing Back Door Depending on the accessories that you want to use with the case, you may need to change the housing back door. Two back doors are included in the standard package: the waterproof housing back door, and the vented housing back door. Do the following to change the housing back door: 1. Open the back door completely. 2. Pull to detach the back door from the case. 3. Detach the T tip adapter from the current back door and install the T tip adapter to the back door you want to use. 4. Install the back door. 5.2 Velcro Strap The Velcro strap can be used to secure the waterproof case onto any object to conveniently record

• HP Action Cam AC200, viii Notes on Waterproof Case Waterproof Case performance  The waterproof case performance is equivalent to IPX8 (60m/1hr).  Underwater time limit: Do not use the waterproof case underwater for more than 60 minutes and 60 meters to ensure water resistance.  The waterproof case is not dust-proof.  The camera and other accessories are not waterproof unless enclosed by the waterproof case.  When using the camcorder in cold or humid environments or when going underwater, use the anti-fog insert to prevent fogging. The anti-fog insert only provides a certain degree of prevention, results vary depending on the actual environment. The anti-fog insert is not fo

Related Products and Documents (Camcorder):

Comparable Devices:

Similar Resources:

• Genius G-Shot HD585T (90 pages) 1Contents Disclaimer ...............................................................5 Precautions.............................................................6 1 Overall Introduction ............................ 8 1.1 System Requirements ..................................8 1.2 Features......................................................... 8 1.3 Acce …

• Panasonic DMC-LX7 (28 pages) VQT4J01M0712KZ0Basic Operating InstructionsDigital CameraModel No. DMC-LX7Before use, please read these instructions completely.More detailed instructions on the operation of this camera are contained in “Operating Instructions for advanced features (PDF format)” in the supplied CD-ROM. Install it on your PC to read it.EBWeb Site: http://www.panasonic-eu …

• Safety Basement SB-DVR80 (13 pages) ank you for purchasing from SafetyBasement.com! We appreciate your business.We made this simple manual to help you enjoy your new product as quickly and easily as possible.Be sure to check the TECH SUPPORT tab on your product page at SafetyBasement.com for the latest available manual.INSTRUCTION MANUALe Original Camstick Pro with 16GBSB-DVR80Revised: A …

• VIEVU LE3 (4 pages) LE3 QUICK START GUIDEThe LE3 is an easy to operate wearable video camera designed specically for professionals that need to video document their actions. LED Status Light Clip Retaining Screw On/Off Switch USB Port & Reset SwitchDetailed SpecicationsVideo Resolution 1280 x 720 (HD) or 848 x 480 (WVGA)Recording Speed 30 Frames Per Seco …

• Zetta Z15 (2 pages) Zetta Z15 HD Security Camcorder Quick Start Guidewww.zetta.com.hkOverviewCongratulations on your purchase of Zetta Z15 HD security camcorder! Zetta Z15 is an intelligent security camcorder with multi-function triggering and multi auto on/off modes. The camcorder comes with a built-in rechargeable battery which can record up to 10 hours continuous video and s …

• JVC LYT0190-001B (88 pages) GR-DVM5DIGITAL VIDEO CAMERALYT0190-001BINSTRUCTIONSENGLISHENPlease visit our CyberCam Homepage onthe World Wide Web and answer ourConsumer Survey (in English only):http://www.jvc-victor.co.jp/index-e.html …

Comments, Questions and Opinions: