HP Bermuda Operation & User’s Manual

Text of HP Bermuda User Guide:

• 20 Bermuda User’s Manual 2. HARDWARE SETUP 14) Sytem, Power Supply and CPU Fan Connectors (3-pin SYS_FAN, PS_FAN, CPU_FAN) These connectors support cooling fans of 350mA (4.2 Watts) or less. Orientate the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the

• HP Bermuda, 6 Bermuda User’s Manual 2. HARDWARE SETUP 2.1 Motherboard Layout Motherboard Layout 2. H/W SETUP Grayed components are available only on certain models at the time of purchase. SYS_FAN Accelerated Graphic Port (AGP) PANEL FLOPPY SECONDARY IDE VIA VT82C686B PCIset 01 DDR DIMM2 (64/72 bit, 184-pin module) 2 3 01 DDR DIMM1 (64/72 bit, 184-pin module) 0 1 BERMUDA 2Mbit Flash EEPROM (Programmable BIOS) PRIMARY IDE PS/2 T: Mouse B: Keyboard AMD761 System Controller CR2032 3V Lithium Cell CMOS Power WOLCON CD AUX GAME_AUDIO Mic In Line Out Line In USB T: USB1 B: USB2 Top: RJ-45 Socket A PCI Slot 1 PCI Slot 3 PCI Slot 2 COM2 HP-USB CLR_CMOS PS_FAN A

• HP Bermuda, 8 Bermuda User’s Manual 2. HARDWARE SETUP 2.4 Motherboard Settings This section explains in detail how to change your motherboard’s function settings through the use of switches and/or jumpers. 2. H/W SETUP Motherboard Settings WARNING! Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electric- ity, you should follow some precautions whenever you work on your computer. 1. Unplug your computer when working on the inside. 2. Use a grounded wrist strap

• HP Bermuda, Bermuda User’s Manual 11 2. HARDWARE SETUP 2.6 Central Processing Unit (CPU) The motherboard provides a Socket 462 or Socket A for CPU installation. The CPU that came with the motherboard should have a fan and heatsink attached to it to prevent overheating. If this is not the case, then purchase and install a set before you turn on your system. WARNING! Make sure that the heatsink is mounted tightly against the processor. Make sure also that there is sufficient air circulation across the processor’s heat- sink by regularly checking that your CPU fan is working. Without sufficient cir- culation, the processor could overheat and damage both the processor and the motherboard. Y

• HP Bermuda, Bermuda User’s Manual 9 2. HARDWARE SETUP 2.5 System Memory (DDR DIMM) This motherboard uses only Double Data Rate (DDR) Dual Inline Memory Modules (DIMMs). Two sockets are available for 2.5Volt (power level) unbuffered/registered Double Data Rate Synchronous Dynamic Random Access Memory (DDR SDRAM) of 64MB, 128MB, 256MB, 512MB, 1GB to form a memory size between 64MB to 2GB. One side (with memory chips) of the DIMM takes up one row on the motherboard. DDR DIMMs support both ECC (Error Correction Code, typically used in servers) and non-ECC (used on desktops/laptops) and are available in

• HP Bermuda, Bermuda User’s Manual 7 2. HARDWARE SETUP 2.2 Layout Contents Motherboard Settings 1) FS1 p. 8 Frequency Selections Expansion Slots/Sockets 1) System Memory p. 9 System Memory Support 2) DIMM1/2 p. 10 DDR DIMM Memory Module Support 3) Socket 462 (Socket A) p. 11 CPU Support 4) PCI1/2/3/ p. 12 32-bit PCI Bus Expansion Slots 5) AGP 4X p. 13 Universal Accelerated Graphics Port (AGP 4X) 6) Golden Finger p. 13 PCI Extension Card Golden Finger Connectors 1) PS2KBMS p. 14 PS/2 Mouse Port connector (6 pin female) 2) PS2KBMS p. 14 PS/2

• HP Bermuda, Bermuda User’s Manual 13 2. HARDWARE SETUP 2.7.3 Accelerated Graphics Port (AGP 4X) This motherboard provides a Universal Accelerated Graphics Port (AGP 4x) slot to support AGP/AGP 4x graphics cards. CAUTION! To avoid damaging your AGP 4X graphics card, your computer’s power supply should be unplugged before inserting your graphics card into the slot. 0 1 0 1 BERMUDA BERMUDA Accelerated Graphics Port (AGP) AGP Card 2.7.4 PCI Extension Card Golden Finger This motherboard features a plug-in extension golden finger configured to support two PC

• 4 Bermuda User’s Manual 1. FEATURES Performance 1. FEATURES 1.1.3 Special Features • ACPI Ready: Advanced Configuration Power Interface (ACPI) provides more Energy Saving Features for operating systems that support OS Direct Power Management (OSPM) functionality. With these features implemented in the OS, PCs can be ready around the clock, yet satisfy all the energy saving stand

• HP Bermuda, 14 Bermuda User’s Manual 2. HARDWARE SETUP 2.8 External Connectors WARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins will cause damage to your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connec- tor on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives. Check the connectors before installation because there may be exceptions. IDE ribbon cable must be less than 46 cm (18 in.), with the sec

• HP Bermuda, Bermuda User’s Manual 23 2. HARDWARE SETUP Connectors 2. H/W SETUP 24) Clear Real Time Clock RAM (R386) A Note about Passwords The BIOS Setup program allows you to specify passwords in the Main menu. The pass- words control access to the BIOS during system startup. The passwords are not case sen- sitive. In other words, it makes no difference whether you enter a password using upper or lowercase letters. The BIOS Setup program allows you to specify two separate passwords: a Supervisor password and a

• HP Bermuda, 16 Bermuda User’s Manual 2. HARDWARE SETUP Connectors 2. H/W SETUP 6) Game/MIDI Connector (Gold 15-pin GAME_AUDIO) You may connect game joysticks or game pads to this connector for playing games. Connect MIDI devices for playing or editing professional audio. Joystick/MIDI (15-pin female) 7) Audio Port Connectors (Three 1/8” GAME_AUDIO) Line Out (lime) can be connected to powered speakers. Line In (light blue) allows tape players or other audio sources to be recorded by your computer or played through the Line Out (lime). Mic (pink) allows microphones to be con-

• HP Bermuda, Bermuda User’s Manual 17 2. HARDWARE SETUP 9) Primary (Blue) / Secondary IDE Connectors (Two 40-1pin IDE) These connectors support the provided UltraDMA/100 IDE hard disk ribbon cable. Connect the cable’s blue connector to the motherboard’s primary (recom- mended) or secondary IDE connector, and then connect the gray connector to your UltraDMA/100 slave device (hard disk drive) and the black connector to your UltraDMA/100 master device. It is recommended that non-UltraDMA/100 devices be connected to the secondary IDE connector. If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to your hard disk docu

• Bermuda User’s Manual 19 2. HARDWARE SETUP 13) Standard Infrared Module Connector (5-1 pin IR) This connector supports an optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure the setting through the BIOS software to select whether UART2 is directed for use with COM2

• HP Bermuda, Bermuda User’s Manual 5 1. FEATURES 1. FEATURES Intelligence 1.1.4 Performance Features • Concurrent PCI: Concurrent PCI allows multiple PCI transfers from PCI mas- ter busses to the memory and processor. • High-Speed Data Transfer Interface: IDE transfers using UltraDMA/33 Bus Master IDE can handle rates up to 33MB/s. This motherboard with its chipset and support for UltraDMA/100 increases the data transfer rate to 100MB/s. UltraDMA/100 is backward compatible with DMA/66, DMA/33, and DMA and with existing DMA devices and systems so there is no need to upgrade current EIDE/IDE drives and host systems. (UltraDMA100/66 requires a 40-pin 80- conductor cable

• HP Bermuda, 22 Bermuda User’s Manual 2. HARDWARE SETUP Connectors 2. H/W SETUP 18) System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED, which lights when the system is powered on and blinks when it is in sleep or soft-off mode. 19) System Warning Speaker Connector (4-pin SPEAKER) This 4-pin connector connects to the case-mounted speaker. 20) System Message LED Lead (2-pin MSGLED) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when there is data re- ceived. This function r

• HP Bermuda, 12 Bermuda User’s Manual 2. HARDWARE SETUP 2. H/W SETUP 2.7 Expansion Cards WARNING! Unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2.7.1 Expansion Card Installation Procedure 1. Read the documentation for your expansion card and make any necessary hard- ware or software settings for your expansion card, such as jumpers. 2. Remove your computer system’s cover and the bracket plate on the slot you intend to use. Keep the bracket for possible future use. 3. Carefully align the card’s connectors and press firmly. 4.

• HP Bermuda, Bermuda User’s Manual 3 1. FEATURES 1. FEATURES Specifications • PCI Expansion Slots: Provides three 32-bit PCI (Rev. 2.2) expansion slots, which can support Bus Master PCI cards, such as SCSI or LAN cards (PCI supports up to 133MB/s maximum throughput.) • PCI Extension Card Golden Finger: This unique extender provides optional support for two additional PCI slots, transforming the micro-ATX motherboard into a standard ATX configuration. • South Bridge Embedded Multi-I/O: Provides two high-speed UART compat- ible serial ports and one parallel port with EPP and ECP capabilities. • Enhanced ACPI & Anti-Boot Virus Protection: Programm

• Bermuda User’s Manual 21 2. HARDWARE SETUP 16) USB Headers (10-2 pin HP_USB) If more USB port connectors are needed, an onboard HP_USB header is avail- able for two additional USB port connectors. Connect the USB headers to an optional 2-port USB connector set and mount the bracket to an open slot on your chassis. 0 1 0 1 BERMUDA BERMUDA USB Port 1 2 11 12 GNDGND GNDGND USBP–USBP– US

• HP Bermuda, 18 Bermuda User’s Manual 2. HARDWARE SETUP 11) Wake-On-LAN Connector (3-pin WOLCON) This connector supports a LAN card with Wake-On-LAN output. The connec- tor powers up the system when a wakeup packet or signal is received through the LAN card. IMPORTANT: This feature requires that the Wake-On-LAN or PCI Modem feature is enabled in BIOS software setup and that your system has an ATX power supply with at least 720mA +5V standby power. 0 1 0 1 BERMUDA BERMUDA Wake-On-LAN Connector IMPORTANT: Requires an ATX power supply with at least 720mA +5 volt standby power WOL_

Related Products and Documents (Motherboard):

Comparable Devices:

Similar Resources:

• MSI 915GVM-V (94 pages) i FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, us …

• Renesas RH850 Series (34 pages) www.renesas.comAll information contained in these materials, including products and product specifications, represents information on the product at the time of publication and is subject to change by Renesas Electronics Corp. without notice. Please review the latest information published by Renesas Electronics Corp. t …

• STMicroelectronics LED7707 (17 pages) May 2009 Doc ID 14893 Rev 1 1/17AN2810Application note6-row 85 mA LED driver with boostconverter for LCD panel backlightingIntroductionThe LED7707 LED driver from STMicroelectronics consists of a high-efficiency monolithic boost converter and six controlled current generators (rows), specifically designed to supply LED arrays used in the backlightin …

• Intel D945PLRN (12 pages) Intel® Desktop Board D945PLRN Specification Update Release Date: November 2006 Order Number: D40357-003US The Intel® Desktop Board D945PLRN may contain design defects or errors known as errata, which may cause the product to deviate from published specifications. Current characterized errata are documented in this Specification Update. …

• AMD 790GX (63 pages) USER'S MANUAL Of AMD 790GX & AMD SB750 Based M/B For Socket AM2+ Quad Core AMD Processor NO. G03-HA07-F Rev：4.0 Release date: October. 2008 Trademark: * Specifications and information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and sh …

• Variscite DART-MX8M (2 pages) DART-MX8M based on NXP i.MX8M Evaluation Kit Quick Start Guide Features: 1. 5V PWR IN (J4) 2. Gigabit Ethernet (J5) 3. USB 3.0 OTG (J6) 4. USB 3.0 Host P2(J7) 5. USB 3.0 Host P1(J8) 6. SD-MMC (J9) 7. USB Debug (J10) 8. RTC BAT. Slot (JBT1) 9. Dual MIPI-CSI (J11) 10. Mini PCIe #1 (J23) 11. UART, I2C (J12) 12. SAI2, SAI5, …

Comments, Questions and Opinions: