Manualios.com

HP E1330A Service Manual

HP E1330A Manual Online:

3, 2646 votes
HP E1330A User Manual
HP E1330A User Guide
HP E1330A Online Manual

Text of HP E1330A User Guide:

  • HP E1330A, Digital I/O Description The HP E1330A/B Digital I/O Module is an "instrument" in a VXIbus mainframe. As such, each Digital I/O module is assigned an error queue, input and output buffers, and a status register. NOTE Instruments are based on the logical addresses of the plug-in modules. See the HP 75000 Series B Installation and Getting Started Guide to set the addresses to create an instrument. HP E1330A/B Description The HP E1330A/B provides four independent 8-bit digital I/O ports compatible with TTL logic levels. Each port can be so

  • HP E1330A, printf("\n\nBit walk test of all ports for read and write (no handshake)"); for (i = 0; i <= 7; i++) { for (j = 0; j <= 3; j++) { iprintf (id, "SOUR:DIG:DATA%u #B%s\n", j, bit_walk[i]); if (j < 2) iprintf (id, "MEAS:DIG:DATA%u?\n", j+2); else iprintf (id, "MEAS:DIG:DATA%u?\n", j-2); iscanf(id, "%t", a); number = atoi(a); if (number != bit_val[i]) { fail = 1; printf("\nFailure of bit walk"); printf("\n WRITE at port %u", j); if (j < 2) printf("\n READ at port %u"

  • HP E1330A, Chapter 2 Verification Tests Introduction This chapter describes the verification tests for the HP E1330A/B modules. The three levels of test procedures described in this chapter are used to verify that the HP E1330A/B: • is functional (Functional Verification Test) • meets selected testable specifications (Operation Verification) • meets all testable specifications (Performance Verification) Test Conditions / Procedures See Table 1-1 for test equipment requirements. You should complete the Performance Verification tests at least once a year. For heavy use or severe operating environments, perform the tests more often.

  • HP E1330A, Contents HP E1330A Digital I/O Module Service Manual Edition 3 Click here to return to HP TS-5400 Systems On-Line Manuals Main Contents Chapter 1. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

  • HP E1330A, Performance Verification Tests The procedure in this section is used to test the module’s electrical performance using the specifications in Appendix A — Specifications of the HP E1330A/B Modules User’s Manual as the performance standard. The Performance Verification test is a test of each Digital I/O line on each port and a test of the three main handshake lines for each port. This test is sufficient to determine that the module is operating within specifications. This test is suitable for incoming inspection, troubleshooting, and preventive maintenance. Test Cable A test cable is required to run the Performance Verification test. This test cable is available from Hewlett-Packard (

  • HP E1330A, † These parts are not compatible with older version fixed handles or their corresponding front panels. To replace one or more of these old parts, you must order all three new parts (Top and Bottom Handle Kits AND Front Panel). Table 3-1. HP E1330A Replaceable Parts Reference Designator HP Part Number Qty Part Description Mfr. Code Mfr. Part Number ASSEMBLIES and CABLES (See Figure 3-1) E1330-66201 1 REPLACEMENT ASSEMBLY 28480 E1330-66201 A1 E1330-66501 1 PC Assembly - Digital I/O 32-Channel 28480 E1330

  • HP E1330A, MANUAL COMMENT SHEET HP E1330A/B Digital I/O Service Manual Manual Part Number E1330-90011 Edition 2 (November 1994) You can help us improve our manuals by sharing your comments and suggestions. Please complete this questionnaire after becoming familiar with the manual and then return it to us. In appreciation of your time, we will enter your name in a quarterly drawing for a Hewlett-Packard Palmtop PC. Please describe the system controller, operating system, and programming language you are using to program this product. Please pencil-in one circle for each stat

  • Repair and Maintenance Guidelines This section provides guidelines for repairing and maintaining the HP E1330A/B Quad 8-Bit Digital I/O Module including: • ESD precautions • Soldering printed circuit boards • Post-repair safety checks ESD Precautions Electrostatic discharge (ESD) may damage static sensitive devices in the module. This damage can range from slig

  • HP E1330A, Safety Considerations This product is a Safety Class I instrument that is provided with a protective earth terminal when installed in the mainframe. Check the mainframe, Digital I/O Module, and all related documentation for safety markings and instructions before operation or service. Refer to the WARNINGS page (page iii) in this manual for a summary of safety information. Safety information for preventive maintenance, testing, and service follows and is also found throughout this manual. Warnings T

  • HP E1330A, Printing History The Printing History shown below lists all Editions and Updates of this manual and the printing date(s). The first printing of the manual is Edi- tion 1. The Edition number increments by 1 whenever the manual is revised. Updates, which are issued between Editions, contain replacement pages to correct the current Edition of the manual. Updates are numbered sequentially starting with Update 1. When a new Edition is created, it contains all the Update information for the previous Edition. Each new Edition or Update also includes a revised copy of this printing history page. Many product updates

  • HP E1330A, 90 CLEAR SCREEN 100 PRINT "Install Component Assembly and Test Cable" 110 PRINT 120 PRINT " 1. Turn mainframe power OFF" 130 PRINT " 2. Install HP E1330A/B component assembly into mainframe " 140 PRINT " 3. Attach test cable to component assembly" 150 PRINT " 4. Turn mainframe power ON " 160 PRINT " 5. Press Continue when ready to begin testing " 170 PAUSE 180 CLEAR SCREEN 190 OUTPUT @Dio;"*IDN?" 200 ENTER @Dio;A$

  • HP E1330A, What’s in this Manual Manual Overview This manual shows how to service the HP E1330A/B Quad 8-Bit Digital I/O Module. Consult the HP E1330A/B User’s Manual for additional information on installing, configuring, and operating the HP E1330A/B. Consult the appropriate mainframe user’s manual for information on configuring and operating the mainframe. Manual Content Chapter Title Content 1 General Information Provides a basic description and lists the test equipment required for service. 2 Verification Tests Functional verification, operation verification, a

  • HP E1330A, Table 3-3. HP E1330A/B Reference Designators HP E1330A/B Reference Designators A ................................................... assembly MP...................................... mechanical part F ............................................................fuse P......................... electrical connector (plug) J.......................... electrical connector (jack) PNL ..................................................... panel JM......................................................jumper SC

  • HP E1330A, † These parts are not compatible with older version fixed handles or their corresponding front panels. To replace one or more of these old parts, you must order all three new parts (Top and Bottom Handle Kits AND Front Panel). NOTE If the 4 IC’s placed in the sockets are square in shape rather than rectangular, the PC assembly (A1 reference designator) is the most recent HP E1330B release, as listed above. If the 4 IC’s are rectangular (see Figure 3-1), the PC assembly is an earlier E1330B release and must be replaced with a new Replacement Assembly (Part Number E1330-66202). Reference Designator HP Part Number Qty Part Description Mfr. Code Mfr. Part Nu

  • HP E1330A, CERTIFICATION Hewlett-Packard Company certifies that this product met its published specifications at the time of shipment from the factory. Hewlett-Packard further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology (formerly Na- tional Bureau of Standards), to the extent allowed by that organization’s calibration facility, and to the calibration facilities of other International Standards Organization members. WARRANTY This Hewlett-Packard product is warranted against defects in materials and workmanship for a period of thr

  • HP E1330A, Chapter 3 Replaceable Parts Introduction This chapter contains information to order replaceable parts for the HP E1330A Quad 8-Bit Digital I/O Modules with serial number prefixes 2934A and HP E1330B with serial number prefixes 3221A. Table 3-1 lists replaceable parts for the HP E1330A Module and Table 3-2 lists replaceable parts for the HP E1330B Module. Table 3-3 shows reference designators for parts in Tables 3-1 and 3-2. Table 3-4 shows the manufacturer code list for these parts. To order a part listed

  • Table 2-1. Performance Test Record (Page 2 of 2) Performance Test Record Test No/Description Minimum Value Measured Value Maximum Value Meas Uncert Test Acc Ratio (TAR) Test 2-1: Digital Test Read/Write Test Port 0 Write/Port 2 Read NA Pass Fail NA NA NA Port 1 Write/Port 3 Read NA Pass Fail NA NA NA Port 2 Write/Port 0 Read NA Pass Fail NA NA NA Port 3

  • HP E1330A, Repair Strategy Hewlett-Packard recommends replacement of the entire assembly in the event of a failure. Procedures in this chapter describe troubleshooting techniques. Troubleshooting Techniques To troubleshoot an HP E1330A/B module problem you must first identify the problem and then isolate the cause of the problem to a replaceable assembly. See Chapter 3 — Replaceable Parts for descriptions and locations of HP E1330A/B replaceable parts. Identifying the Problem Table 4-1 lists some common problems for the HP E1330A/B modules, along with symptoms and possible solutions. If the problem cannot be identified using

  • HP E1330A, Table 4-2. HP E1330A/B Visual Tests/Checks Test/Check Reference Designator Check Action/Notes Heat Damage - - - - - - - - - - - - - - - Discolored PC boards Damaged insulation Evidence of arcing If there is damage, do not operate the module until you have corrected the problem. Switch/Jumper Settings J15, J16 SW1 J51,J52,J53,J54 J12 IRQ Level setting Logical address setting Pull-up Enable FLG Combine Factory set at 1 Factory set at 144 Factory set to Enable Factory set to no jumpers Component Assembly F1 J1-J2 P1 Fuse continuity Dirty or bent connector pins Dirty or bent connector pins Check fuse with ohmmeter Straighten/cl

  • HP E1330A, Table 2-1. Performance Test Record (Page 1 of 2) General Information Test Facility: Name _____________________________________ Address _____________________________________ City/State ___________________________________ Phone _____________________________________ Report No. _________________________________ Date _____________________________________ Customer ___________________________________ Tested by __________________________________ Special Notes: _____________________________________________________________________________________________ _______________

  • HP E1330A, Performance Test Record Table 2-1, Performance Test Record, is a form you can copy and use to record performance verification test results for the Module. Test Limits The HP E1330A/B test is a pass/fail test and has no test limits. Minimum and Maximum values are marked NA (Not Applicable) in Table 2-1. Measurement Uncertainty The HP E1330A/B test is a pass/fail test and has no measurement uncertainty. The measurement uncertainty column is marked NA(Not Applicable) in Table 2-1. Test Accuracy Ratio (TAR)

  • HP E1330A, Performance Verification Test This program is designed to do the Performance Verification Test found in Chapter 2 - Verification Tests. Example: Digital Test This example performs a bit walk test of all bits on all ports and checks the module’s ability to set and reset the handshake lines on each port. /* Digital I/O Test E1330A */ #include <stdio.h> #include <stdlib.h> #include <sicl.h> #define ADDR "hpib7,9,18" /* Address of device */ void main (void) { INST id; /* Define id as an instrument */ char a[255], b[32]; char *bit_walk[] = {"00000001", "00000010", "00000100", "00001000",

  • HP E1330A, Recommended Test Equipment Table 1-1 lists the test equipment recommended for testing, adjusting, and servicing the Digital I/O modules. Essential requirements for each piece of test equipment are described in the Requirements column. Table 1-1. Recommended Test Equipment Instrument Requirements Recommended Model Use* Controller, HP-IB HP-IB compatibility as defined by IEEE Standard 488-1987 and the identical ANSI Standard MC1.1: SH1, AH1, T2, TE0, L2, LE0, SR0, RL0, PP0, DC0, DT0, and C1, 2, 3, 4, 5. HP 9000 Series

  • Chapter 4 Service Introduction This chapter contains service information for the HP E1330A/B Quad 8-Bit Digital I/O Modules. Also included are trouble shooting, repair, and maintenance guidelines. WARNING Do not perform any of the service procedures shown unless you are a qualified, service-trained technician and have read the WARNINGS and CAUTIONS in Chapter 1. Equipment Required Equi

  • HP E1330A, Chapter 4. Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Service Aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Digital I/O Module Description . . . . . . . . . . . . . . . . . . . . . . . . .

  • Chapter 1 General Information Introduction This manual contains information required to test, troubleshoot, and repair the HP E1330A/B Quad 8-Bit Digital I/O Module. See the HP E1330A/B User’s Manual for additional information on the HP E1330A/B. Figure 1-1 shows the HP E1330A/B Quad 8-Bit Digital I/O Module. Figure 1-1. HP E1330A/B Digital I/O Module Chapter 1 General Informa

Related Products and Documents (Network Card):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Qlogic SANbox 5200 Series Supplementary manual qlogic/sanbox-5200-series-484.pdf 07 Nov 2022 2 0.53 Mb
2 MATLAB CURVE FITTING TOOLBOX 2 Operation & user’s manual matlab/curve-fitting-toolbox-2-85J.pdf 27 Apr 2023 767
3 WATT AGE Tiger shark Operating instructions manual watt-age/tiger-shark-WX7.pdf 17 Oct 2022 16
4 QuStream AAB6214 Technical manual qustream/aab6214-899.pdf 18 Aug 2022 25
5 AT&T 9111 Operation & user’s manual at-t/9111-44Z.pdf 12 Jun 2023 16 2.34 Mb
6 Alesis DM8 PRO KIT Operator's manual alesis/dm8-pro-kit-FI9.pdf 01 Feb 2024 48 1.03 Mb

Similar Resources:

  • Cisco

    Catalyst 4500 Series

    (11 pages)
    © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information. Page 1 of 1 Data Sheet Cisco Catalyst 4500 Series Switch Overview The Cisco® Catalyst® 4500 Series Switches enable Borderless Networks, providing high performance, mobile, and secure user experiences through Layer 2-4 switching investments. They enable s …
  • Toshiba

    EX100

    (9 pages)
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ …
  • Omron

    CJ Series

    (64 pages)
    RGB ELEKTRONIKA AGACIAK CIACIEKSPÓŁKA JAWNA Jana Dlugosza 2-6 Street51-162 WrocławPoland [email protected] +48 71 325 15 05www.rgbautomatyka.plwww.rgbelektronika.plDATASHEETwww.rgbautomatyka.plwww.rgbelektronika.pl OTHER SYMBOLS:3G3AX-MX2-EIO15-EOMRON …
  • Texas Instruments

    TMS320DM36X

    (134 pages)
    TMS320DM36x Digital Media System-on-Chip(DMSoC)Ethernet Media Access Controller (EMAC)User's GuideLiterature Number: SPRUFI5BMarch 2009–Revised December 2010 …
  • National Instruments

    E Series

    (132 pages)
    DAQCard E SeriesUser Manual Multifunction I/O Cards for PCMCIA June 1996 EditionPart Number 321138A-01  Copyright 1996 National Instruments Corporation. All Rights Reserved. This document was created with FrameMaker 4.0.4 …
  • Lindy

    25121

    (15 pages)
    © LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (Feb 2004) HomePlug USB Adaptor User Manual English LINDY No. 25121 www.LINDY.com …

Comments, Questions and Opinions: