Hughes HN7700S Installation Manual

Text of Hughes HN7700S User Guide:

• Hughes HN7700S, Chapter 7 • System Control Center 1037753-0001 Revision A 43 Accessing the System Control Center You can access the System Control Center through a Web browser installed on a computer connected to the HN router. To access the System Control Center use the following steps: 1. Open a Web browser such as Internet Explorer or Netscape. 2. In the browser’s address bar, type www.systemcontrolcenter.com or 192.168.5.1 and press ENTER. A sample of the System Control Center home page appears as shown in Figure 34. The System Control Center home page The System Control Center also referred to as the Home page or the Main page

• Hughes HN7700S, Chapter 4 • Connecting the HN router to a transport device 1037753-0001 Revision A 15 Chapter 4 Connecting the HN router to a transport device This chapter explains how to connect the HN router to a transport device. It covers the following topics. • Connecting the cables to a modem transport device on page 15 • Connecting the cables to a T-1 transport device on page 16 • Powering up and observing the router LEDs on page 16 Connecting the cables to a modem transport device To connect the modem transport device: 1. Connect the installer P

• Hughes HN7700S, • Figures 1037753-0001 Revision A xi 64. Internet Protocol Properties - Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 65. Network and Dial-up Connections - Windows 2000 . . . . . . . . . . . . . . . . . . . . .75 66. Local Area Connection Properties - Windows 2000 . . . . . . . . . . . . . . . . . . . . .75 67. Internet Protocol Properties - Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . .76 Appendix B 68. Saving the Fallback Updater utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

• Hughes HN7700S, Appendix E • ADTRAN Total Access 600R 114 1037753-0001 Revision A 8. Select unassigned and press Enter. 9. Select Router 64K for the Port as shown in Figure 100. 10. Use this process to configure the number of channels indicated on your FSO. Figure 101 illustrates eight channels configured. Figure 100: Mapping a DS0 port Figure 101: Mapping multiple DS0s

• Hughes HN7700S, Chapter 5 • Commissioning the HN router 1037753-0001 Revision A 21 4. Click Advanced Commissioning Options as shown in Figure 8. 5. The Broadband Satellite Setup screen displays as shown in Figure 9. 6. Click the Mode Change link. This initiates the process to change the mode from VSAT to router. Figure 9: Setup screen

• Hughes HN7700S, Appendix F • Siemens 4100/4101 DSL Modem 1037753-0001 Revision A 121 5. The system displays the Downloading Firmware message as shown in Figure 107. 6. The system displays the rebooting message a show in Figure 108. Figure 107: Downloading Firmware Figure 108: Rebooting Device message

• Hughes HN7700S, Appendix D • Conformance with standards and directives 96 1037753-0001 Revision A Canada Class B warning This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. R&TTE (EU) This product is within the scope of the EU Radio Equipment and Telecommunications Terminal Equipment (R&TTE) Directive. Telecommunications standards This section explains compliance with the IP over Satellite standard (IPoS) and FCC Part 68. IPoS The Hughes system is compliant with IPoS, ratified by the Telecommunications Industry Association (TIA-1008), first published in October 2003 and issued as Revi

• Hughes HN7700S, Appendix B • Updating the router software 78 1037753-0001 Revision A 3. Open the self-extracting file. The Self Extractor dialog appears as shown in Figure 68. 4. Use the Browse button to select a location in which to unzip and save the utility and its supporting files. 5. Click Unzip. Configuring TCP/IP properties on the installer laptop Before using the Fallback Updater utility, you must first manually configure the TCP/IP properties on your laptop. This section explains how to configure TCP/IP properties for Wind

• Appendix E • ADTRAN Total Access 600R 104 1037753-0001 Revision A page 104. This figure illustrates the top-level menu. The structure of the window consists of the following elements. • Menu path - Shows the session’s current path in the menu structure. • Window panes - There are two window panes, the left and right panes. – The left pane shows the list

• Hughes HN7700S, Chapter 5 • Commissioning the HN router 24 1037753-0001 Revision A 3. Select the appropriate file. 4. Click the Upload button. 5. The system displays a confirmation screen as shown in Figure 13 indicating the the file was successfully transferred. 6. Click the Close button. 7. The system returns to the SCC home page. Commissioning by auto selection Commissioning by auto selection is the preferred method of commissioning the HN router. By selecting this option the commissioning parameters are automatically configured based on the network access provider (NAP) chosen. Selecting and verifyin

• Hughes HN7700S, Appendix F • Siemens 4100/4101 DSL Modem 1037753-0001 Revision A 119 • The Internet LED should remain a solid green. • The Activity LED may blink. Installing the modem To establish a connection from your computer to the modem: 1. After connecting the modem, power up your laptop. 2. Click the icon appears on the screen that was downloaded from the installer portal. Notice that the Power, Ethernet, and DSL LEDs on the modem will turn green. The installation interface The installation process is an automated process composed of the following steps: • Search

• Hughes HN7700S, Chapter 8 • Configuring the HN router for VADB backup 1037753-0001 Revision A 65 If the current_state field changes to SESSION INACTIVE and there is no connection to the satellite (you can’t browse), troubleshoot by verifying that the HN router can ping the VADB gateway: 1. Open the Run dialog box by selecting Start → Run. 2. Type Command . 3. Click OK. 4. Type ping <VADB gateway address> and press ENTER. The VADB gateway address appears on the VADB Config Show page ( Figure 52 on page 59). If the clien

• Hughes HN7700S, Appendix B • Updating the router software 84 1037753-0001 Revision A 7. Select Use the following IP address. 8. Type 192.168.0.2 in the IP address field. 9. Type 255.255.255.252 in the Subnet mask field. 10. Click OK. 11. Restart the computer even if Windows does not require you to do so. This ensures that the network settings are automatically reset. Windows 2000 1. Connect the laptop to the router with an Ethernet cable. 2. From the Windows desktop on the installer laptop, select Start → Settin

• Hughes HN7700S, Appendix B • Updating the router software 1037753-0001 Revision A 83 4. Ensure that Client for Microsoft Networks and Internet Protocol (TCP/IP) are installed and checked as shown in Figure 73. If NetBEUI is installed, uninstall it. 5. Select Internet Protocol (TCP/IP). Be careful not to uncheck the check box. 6. Click Properties. The Internet Protocol Properties dialog appears as shown in Figure 74. Figure 73: Local Area Connection Properties - Windows XP Figure 74: Internet Protocol Properties - Windows XP

• Hughes HN7700S, Chapter 7 • System Control Center 50 1037753-0001 Revision A System Info page The System Info page, as shown in Figure 43 on page 50 provides basic system configuration information for the HN router. The page is divided into two sections. The HN router Info section contains identifying information for the router such as the Site ID and Serial Number. The Software Configuration section displays NAT, DHCP, and Firewall information if these options are enabled. Figure 43: System Info page

• Appendix C • Disabling a Web browser’s proxy connection 90 1037753-0001 Revision A 4. Select the Connections tab as shown in Figure 79. 5. Click LAN Settings to access the dialog box shown in Figure 80. 6. Click to remove the check mark from the box next to Use a proxy server for your LAN . 7. Click OK. 8. Close Internet Explorer. 9. Relaunch Internet Explorer to enable the ch

• Hughes HN7700S, Chapter 3 • Assembling and connecting the HN router hardware 1037753-0001 Revision A 13 Connecting a DC/DC power supply Figure 5 shows the DC/DC power supply used with the HN router. Connect the DC/DC power supply as follows: 1. Connect the DC power cord to the DC IN port on the HN router. 2. Assemble the input power cable according to the wiring diagram included in the cable kit. Connect the input power cable to the DC power source, but do not connect the input power connector to the power supply at this time. Figure 5: DC/DC power supply Note: The input cable kit is included in the power

• Appendix E • ADTRAN Total Access 600R 106 1037753-0001 Revision A Connecting the ADTRAN To connect the ADTRAN: 1. Connect the power cord from the AC PWR plug to the designated T1 outlet. 2. Connect the installer laptop to the 10/100 Base T port on the back of ADTRAN unit with an Ethernet cable. 3. Press any key to display the login screen. Logging in

• Chapter 7 • System Control Center 46 1037753-0001 Revision A view status details and restore previous operating parameters. – If the indicator button is red and Problem appears below it, as shown in Figure 39, there is a problem. Click the indicator to access the System Status page to view problem details. Other System Control Center buttons LAN Info shows the co

• Chapter 8 • Configuring the HN router for VADB backup 58 1037753-0001 Revision A Requirements for VADB The following requirements must be fulfilled before VADB can be used: • The HN router must be configured for VADB operation before the system is installed and commissioned. • The site must have an analog telephone line to support VADB operation. A dedicated telephone line is prefe

• Hughes HN7700S, Chapter 6 • Verifying the installation and commissioning 1037753-0001 Revision A 37 Chapter 6 Verifying the installation and commissioning This chapter discusses the final steps of the commissioning process. It covers the following topics: • Verifying the terrestrial link on page 37 • Verifying the download status on page 38 • Completing the process on page 40 Verifying the terrestrial link Use the System Control Center and the Advanced pages to verify commissioning. To verify that the Terrestrial Link is successful, use the following steps to access the Advance Page. 1. Navigate to the Advance Page. 2. Click the General link

• Hughes HN7700S, Chapter 3 • Assembling and connecting the HN router hardware 1037753-0001 Revision A 11 Selecting the router location Select a location for the router that will accommodate all required cable connections, including the power source. Place the router in the desired location. Connecting the power supply Begin installation of the router by connecting the correct power supply. Use the power supply shipped with the router. Refer to Table 2 and Figures 4 and 5 to ensure you have the correct power supply type (AC/DC or DC/DC) for the u

• Hughes HN7700S, Chapter 7 • System Control Center 1037753-0001 Revision A 41 Chapter 7 System Control Center The System Control Center is an interface that enables users to access router configuration, statistics, and status information using a web browser from any computer that has TCP/IP connectivity to the terminal. This chapter discusses: • Internet browser settings on page 41 • Accessing the System Control Center on page 43 • The System Control Center home page on page 43 • System Control Center buttons and indicators on page 44 • The System Status page on page 46 • LAN Info page on page 47 • WAN Info page on page 49 • Syste

• Hughes HN7700S, Chapter 8 • Configuring the HN router for VADB backup 1037753-0001 Revision A 63 Installing the protection module To install a protection module, refer to Figures 54 through 56 and follow these instructions: 1. Connect the short telephone cable from the protection module MODEM port to the HN router TEL LINE port, as shown in Figure 55. 2. Remove the coaxial cable from the HN router SAT IN port. See Figure 56. 3. Slip the ring terminal at the end of the protection module grounding cable over the SAT IN terminal post. Figure 55: Connecting the protection module to the terminal Short phone cable Ground cable Protection module Longer phone cable MODEM port LINE port HN

More Instructions:

	Hughes HN7700S Operation & user’s manual 06-06-2023 126	DOWNLOAD
	Hughes HN7700S Operation & user’s manual 13-03-2024 98	DOWNLOAD

Related Products and Documents (Wireless Router):

Comparable Devices:

Similar Resources:

• Asus RT-N65U (70 pages) RT-N65U Dual-band Wireless-N750 Gigabit RouterThe ultra-thin and stylish RT-N65U features a 2.4GHz and 5GHz dual bands for an unmatched concurrent wireless HD streaming; SMB server, UPnP AV server, and FTP server for 24/7 file sharing; a capability to handle 300,000 sessions; and the ASUS Green Network Technology, which provides up to 70% power-saving solu …

• D-Link DSL-2750B (6 pages) ADSL Modem Installation Guide Make sure that the following are included on the package:  Wireless Modem  Ethernet/Internet Cable (colour yellow)  DSL Cable ( colour grey)  Power Adaptor (colour black)  Filter/Splitter – ( small black box with tail like phone cord at the end) (Please refer to page 6 for the illustration …

• Pepwave MAX (77 pages) COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Copyright © 2009 Pepwave Ltd. All Rights Reserved. Pepwave and the Pepwave logo are trademarks of Pepwave Ltd. Other brands or products mentioned may be trademarks or registered trademarks of their respective owners. User Manual Mobile Router …

• H3C SR6600 Series (22 pages) H3C SR6600/SR6600-X Routers FAQ Copyright © 2017 New H3C Technologies Co., Ltd. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. The information in this document is subject to change w …

• D-Link AC750 (2 pages) INSTALLATION• DAP-1530 || AC750 Mesh Wi-Fi Range Extender• Quick Installation Guide• Quick Installation CardENGLISHPACKAGE CONTENTSDLINK WIFI APP SETUPQuick Installation GuideDAP-1530AC750 Mesh Wi-Fi Range ExtenderPlug the Range Extender into a power outlet near your router.Download the D-Link Wi-Fi app and launch it.1 / 2 /D-Link Wi-FiD-Link …

• HP J6039C - JetDirect 200M Print Server (181 pages) User's Guidefor HP Jetdirect 200m print serverand HP Jetdirect 250m print server Contents:1. Basics of networking and network printing2. General information about the print servers3. Installation of the print servers.4. Configuration and management -- please refer to the HP Jetdirect Administrator's Guide. In that document, click on one of thes …

Comments, Questions and Opinions: