Intergraph Intense3D Wildcat 3510 Hardware User's Manual

Text of Intergraph Intense3D Wildcat 3510 User Guide:

• Intergraph Intense3D Wildcat 3510, 11 3 Technical Information The following technical information is subject to change without notice. Hardware Specifications Item Specification System AGP 2.0 Card Size Full-length AGP card Monitor Resolutions In the following tables, i indicates an interlaced frequency. The Wildcat 3510 supports standard multiple-frequency monitors at the following resolutions and maximum refresh rates (Hz). Resolution Aspect Ratio Bits Per Pixel Vertical Refresh Rates (Hz) 640 x 480 4 x 3 128 60, 72, 75, 85, 60i 800 x 600 4 x 3 128 60, 72

• Intergraph Intense3D Wildcat 3510, vi Customer Support Intergraph Computer Systems offers an assortment of customer support options. Hardware and Software Support Services Intergraph Computer Systems provides a variety of hardware services for Intergraph and third- party equipment. Services include warranty upgrades, repair depot service, on-site hardware maintenance, system administration, and network consulting. Hardware purchased from Intergraph Computer Systems includes a factory warranty ranging from 30 days to three years. A detailed warranty descri

• Intergraph Intense3D Wildcat 3510, 6 Removing and Installing Cards To remove an installed Intense3D Wildcat 3510 card: 1. Turn off power to the workstation and to the monitor. 2. Open the workstation to gain access to the AGP slot. 3. Remove the existing card. Keep the screws; you will use them to secure the card to the workstation’s chassis later. To install the Intense3D Wildcat 3510 card: 1. Align the card with the AGP expansion slot, making sure the gold-fingered connections on the card’s edge are aligned properly with the slot connector. 2. Push the card into the AGP slot firmly and evenly until it is fully seated in the AGP s

• Intergraph Intense3D Wildcat 3510, vii If you have trouble connecting to or using the IBBS, call the Customer Response Center at 1-800-633-7248 (product entry IBBS) or leave a message for the IBBS System Operator at 1-256-730-1413. Telephone To get customer support by telephone: ♦ In the United States, call the Customer Response Center at 1-800-633-7248 between the hours of 7:00 a.m. and 7:00 p.m. Central Time, Monday through Friday (except holidays). ♦ Outside the United States, contact your local Intergraph Computer Systems subsidiary or distributor. Have the following information available when you call: ♦ Your service number, which identifies your site to

• Intergraph Intense3D Wildcat 3510, 2 ♦ Support for industry-standard monitors ♦ Hardware support for stereoscopic viewing, Display Data Channel (DDC), and Display Power Management Signaling (DPMS) Visit http://www.intense3d.com for the latest performance data and other product information. Hardware The Wildcat 3510 is a single-card solution that uses one AGP slot in your workstation. Driver Software The Wildcat 3510 uses the Intense3D Wildcat video display driver. The video display driver installs as a standard Windows NT driver, and provides both GDI and OpenGL graphics compatibility. In a workstation purchased with the Wildcat 3510, the current driver is installed on your works

• 14 Stereo Sync Output Port The stereo sync output port is a female, 5-pin, mini-DIN connector. The port provides connection to the emitter module of a pair of LCD shutter glasses or to other stereo shutter devices. Pin Signal Name 1 Ground 2 Ground 3 +12V 4Stereo Sync 5 No Connect x 1 2 4 5 3

• Intergraph Intense3D Wildcat 3510, 3 NOTE If a workstation monitor has no built-in video cable, use a shielded video cable with a 15-pin (D-sub) video connector at one end for the video output port on the card, and the appropriate connectors at the other end for the video input port on the workstation monitor. Monitor input ports are usually D-sub or Bayonet Nut Connect (BNC) connectors. Shielded cables usually have a ferrite core (a box- or cylinder-shaped attachment) near each end to reduce interference with radio frequencies. 2. Turn on power to the workstation. The video display starts in VGA m

• Intergraph Intense3D Wildcat 3510, 4 4. Click OK to close the Display Properties dialog, or click Cancel to close Display Properties without applying the changes. 5. Restart the system for changes to video attribute settings to take effect. (Certain changes, such as gamma correction, do not require that you restart the system.) For more detailed configuration information, see Chapter 2 and the README.TXT file on the delivery media containing the Wildcat 3510 video display driver. After you configure the video display, verify that the Wildcat 3510 driver is the default video display driver that runs automatically when you start

• Intergraph Intense3D Wildcat 3510, 13 The Wildcat 3510 also provides hardware support for the Display Power Management Signaling (DPMS) standard. DPMS allows for a workstation to send its monitor a signal to enter a power- saving mode. Interfaces The Wildcat 3510 has two interfaces: a video output port and a stereo sync output port. These interfaces are described in the following sections. Video Output Port The video output port is a blue, female, 15-pin, D-Sub connector. The port provides connection to a workstation monitor. The recommended cable length is less than three meters. Pin Signal Name Pin Signal Name 1 Red Analog Video

• Intergraph Intense3D Wildcat 3510, v Preface The Intense3D Wildcat 3510 Graphics Hardware User’s Guide provides information and technical specifications on the Intense3D Wildcat 3510 graphics accelerator. About This Document The Intense3D Wildcat 3510 Graphics Hardware User’s Guide is organized as follows: ♦ Chapter 1, “Getting Started,” introduces the Wildcat 3510 and its features, and describes how to get started using the Wildcat 3510 in your workstation. ♦ Chapter 2, “Replacing and Upgrading the Wildcat 3510,” provides instructions for replacing Wildcat 3510 hardware, installing cards, reinstalling driver software, and troubleshooting the installation. ♦ Chapter 3, “Technical Informa

• Intergraph Intense3D Wildcat 3510, 7 Finishing the Installation To finish the installation: 1. Close the workstation. 2. Connect the workstation’s monitor as described in Chapter 1. Installing Driver Software You can install the Intense3D Wildcat video display driver software from the backup media delivered with the system. You can also get updated driver software from Intergraph Computer Systems’ Web pages; see the Preface of this document for more information. Refer to the Microsoft Windows NT documentation and online Help for more information on installing drivers and software application programs, and on configuring your workstation’s video display.

• Intergraph Intense3D Wildcat 3510, iii Contents Preface............................................................................................................................................. v About This Document....................................................................................................................... v Document Conventions..................................................................................................................... v Operating System Information.......................................................................................................... v Customer Support........................

• Intergraph Intense3D Wildcat 3510, Copyright  1999 Intense3D, Inc. All rights reserved. This document contains information protected by copyright, trade secret, and trademark law. This document may not, in whole or in part, be reproduced in any form or by any means, or be used to make any derivative work, without written consent from Intense3D. Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subdivision (c)(1)(ii) of the rights in technical data and computer software clause at DFARS 252.227-7013. Unpublished rights are reserved under the copyright laws of the United States. Intense3D, Inc., Huntsville A

• Intergraph Intense3D Wildcat 3510, 8 9. Click Yes when asked if you want to install a third-party driver. The files are copied from the directory on your workstation’s primary hard disk drive. NOTE If the driver files were delivered on two floppy diskettes, you will be prompted to key in the path for the driver files from the second diskette. The files are copied from the directory on your workstation’s primary hard disk drive. 10. After the driver files are successfully copied, a message that the driver successfully installed displays. Click OK. 11. Click Clos

• Intergraph Intense3D Wildcat 3510, 1 1 Getting Started This chapter introduces the Wildcat 3510 graphics accelerator and describes what you need to use it in your workstation. System Requirements To use the Wildcat 3510, you will need: ♦ A workstation running on Intel’s Pentium ® II (or later) processor or equivalent ♦ Microsoft Windows NT ® Workstation 4.0 operating system (with SSE/SIMD extensions for optimal performance on systems using Intel’s Pentium III processor) ♦ A full-length Advanced Graphics Port (AGP) slot to insert the Wildcat 3

• 5 2 Replacing and Upgrading the Wildcat 3510 Graphics Card Follow the instructions in this chapter if you must replace or upgrade the Wildcat 3510 in your workstation. Refer to your workstation’s documentation for instructions on opening and closing the system and identifying the AGP expansion slot. Taking Antistatic Precautions Static electricity can damage the component

Related Products and Documents (Video Card):

Comparable Devices:

Similar Resources:

• Gigabyte GV-R675SL-1GI (32 pages) GV-R677SL-1GD/GV-R675SL-1GIAMD RadeonTM HD 6700 Graphics AcceleratorUser's ManualRev. 10112MM-R677LGD-101ERCopyright© 2011 GIGABYTE TECHNOLOGY CO., LTDCopyright by GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT"). No part of this manual may be reproduced or transmitted in any form without the expressed, written permission of GBT.TrademarksThird-party b …

• Digital Equipment mach64 (12 pages) AlphaStation 200 4/100mach64 Graphics Accelerator InstallationGuide Part Number: EK-PCDGA-DI. A01February 1995This document is a guide for installing the mach64 (PB2GA-FA/FN/FV) graphicsoption in Digital AlphaStation 200 4/100 systems.Digital Equipment CorporationMaynard, Massachusetts …

• Gigabyte GV-R477D5-512H-B (32 pages) GV-R477D5-512H-BATI RadeonTM HD 4770 Graphics AcceleratorUser's ManualRev. 10112MM-R477D5B-101RCopyright© 2009 GIGABYTE TECHNOLOGY CO., LTDCopyright by GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT"). No part of this manual may be reproduced or transmittedin any form without the expressed, written permission of GBT.TrademarksThird-party brands and na …

• MSI NX6600LE-TD256 (2 pages) Hardware InstallationFollow the steps to install the VGA card :1. Remove the computer case.2. Locate the PCI Express slot on your mainboard. Warning: Inserting the VGA card into a wrong slot (e.g. AGP slot) may damage your card (refer to your mainboard manual for more Information).3. Put the card directly over the slot and press one end of t …

• 3Dlabs Wildcat II 5110 (57 pages) ====Paä~ÄëI=fåÅK=táäÇÅ~í=ff=RNNM=dê~éÜáÅë=^ÅÅÉäÉê~íçê=`~êÇ=rëÉêÛë=dìáÇÉ= 3Dlabs®, Inc. 480 Potrero Avenue Sunnyvale, CA 94086 408 - 530 - 4700 www.3dlabs.com …

• MSI RX1050-TD128E (2 pages) Hardware InstallationFollow the steps to install the VGA card :1. Remove the computer case.2. Locate the PCI Express slot on your mainboard. Warning: Inserting the VGA card into a wrong slot may damage your card (refer to your mainboard manual for more Information).3. Put the card directly over the slot and press one end of the card into the …

Comments, Questions and Opinions: