Manualios.com

IOGear GCS1204 Installation Manual

IOGear GCS1204 Manual Online:

3.25, 2777 votes
IOGear GCS1204 User Manual
IOGear GCS1204 User Guide
IOGear GCS1204 Online Manual

Text of IOGear GCS1204 User Guide:

  • IOGear GCS1204, 40 41 15.21 You are cautioned that changes or modications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

  • 3 Table of Contents Conventions 4 Package Contents 5 Requirements 6 Operating systems 7 Components 8 Hardware Setup 12 Basic Operation 14 Port ID numbering 17 Advanced Conguration 21 Summary of Hotkey Settings 23 Comparison of Default and Alternate Manual Port selection settings 25 Firmware up-grade mode 26 The Firmware Upgrade Utility 32 Troubleshooting 36 Speci

  • IOGear GCS1204, 30 31 PC Keyboard Sun Keyboard [Ctrl] [F10] Cut [Ctrl] [1] [Ctrl] [2] [Ctrl] [3] [Ctrl] [4] [Ctrl] [H] Help Compose Note: Press and release the  rst key [Ctrl], then press and release the activation key.

  • IOGear GCS1204, 13 12 Hardware Setup Make sure that power to all the devices you will be installing has been turned off. You must unplug the power cords of any computers that have the Keyboard Power On function. Cable Connection To install your GCS1204, refer to the diagram on the following page. The numbers in the diagrams correspond to the steps, below. 1. Connect your USB keyboard and mouse into the USB Console Ports located on the unit’s rear panel. 2. Connect your microphone, speakers, and monitor into the Console ports located on the unit’s rear panel 3. Using the KVM cables, connect th

  • IOGear GCS1204, 4 5 Conventions This manual uses the following conventions: Monospaced Indicates text that you should key in. [ ] Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them: [Ctrl+Alt]. 1. Numbered lists represent procedures with sequential steps. • Bullet lists provide information, but do not involve sequential steps. ––> Indicates selecting the option (on a menu or dialog box, for example), that comes next. For example, Start ––> Run means to open the Start menu, and then select

  • IOGear GCS1204, 44 WE’RE HERE TO HELP YOU! NEED ASSISTANCE SETTING UP THIS PRODUCT? Make sure you: 1. Use the live chat at www.iogear.com to try and solve any issues you may be having with the product 2. Visit the Tech Info Library/FAQ on www.iogear.com (under the Support tab) 3. Call the 24/7 tech support line at 1(866) 946-4327 (U.S. only) or (949) 453-8782 Warranty Information This product carries a 3 Year Limited Warranty. For the terms and conditions of this warranty, please go to http://www.iogear.com/support/warranty or call 1-866-946-4327 Register online at http://www.iogear.com/register Important Product Information Product Model _________________ Serial # _______________________ War

  • 20 21 Hotkey Action [Scroll Lock] [Scroll Lock] [A] Enter] Invokes Auto Scan. The KVM focus cycles from port to port at 5 second intervals (default interval) [Scroll Lock] [Scroll Lock] [A] [N] Enter] The KVM focus cycles from port to port at N seconds interval

  • 10 11 No. Component Description 1 Firmware Upgrade Port Connection for the rmware up-grade cable 2 USB Console Ports USB1.0 Keyboard and mouse connections 3 Console Port Section Monitor, mike, and speaker connections 4 CPU Port Section Connections for the cables that link the switch to your computers. Each CPU port is comprised of a microphone jack, s

  • IOGear GCS1204, © 2007 IOGEAR, INC. FUN IOGEAR offers connectivity solutions that are innovative, fun, and stylish, helping people enjoy daily life using our high technology products. GREEN IOGEAR is an environmentally conscious company that emphasizes the importance of conserving natural resources. The use of our technology solutions helps reduce electronic waste. HEALTH IOGEAR supports healthy and t lifestyles. By integrating products with the latest scientic developments, IOGEAR’s solutions enhance the life of end- users. About Us About Us

  • IOGear GCS1204, 36 37 Specications Function GCS1782(GCS1784) Computer Connections 4 CPU Port Selection Front Panel Pushbuttons; Hotkey Console Connectors Keyboard 1 x USB Type A F (black, rear panel) Mouse 1 x USB Type A F (black, rear panel) Video 1 x DVI-I F (white) Audio* Line in Port 2x Mini Stereo Jack (green; 1 x front panel, 1 x rear panel) Microphone Port 2x Mini Stereo Jack (pink; 1 x front pa

  • IOGear GCS1204, 24 25 Action Default Alternate Press and release a port selection pushbutton Switches only the KVM focus to the selected port KVM, Audio and USB focus switch to the selected port Press a port selection pushbutton twice Audio focus switches to the selected port Audio focus switches to the selected port Press and hold a port selection pushbutton for more than 2 seconds KVM focus, USB, and Audio focus switch to the selected port Switches only the KVM focus to the selecte

  • IOGear GCS1204, 15 14 Hotkey switching All port switching begins by tapping the Scroll Lock key twice. The tables below describe the actions that each combination performs. Note: If the Scroll Lock key conicts with programs running on the computer, or your keyboard does not have a Scroll Lock, see the section titled Advanced Switching to use the alternate switching method.

  • IOGear GCS1204, 22 23 Summary of Hotkey Settings Action Key sequence result Port Switching Invoke HSM Press and release [T] Changes the [Scroll Lock] key to [Ctrl] USB reset 1. Invoke HSM. 2. Press and release [F5] Resets the USB peripheral ports Restore Default Settings 1. Invoke HSM. 2. Press [R] [Enter]. Reset the KVM to its default hotkey settings Hotkey Beeper Control 1. Invoke HSM. 2. Press [B] Toggles the Beeper On and Off Disable Port Switching Hot Keys 1. Invoke HSM 2. Press [X] [Enter] Toggles Hotk

  • IOGear GCS1204, 34 35 Upgrade Failed If the Upgrade Succeeded screen does not appear, it means that the upgrade failed to complete successfully, in which case you should do the following: 1. Power off the GCS1204 and remove its housing. 2. Using a jumper cap, short the jumper on the mainboard labeled J17. The diagram below indicates the jumper location on the GCS1204 board: 3. Power on the GCS1204. It will now work with the factory default rmware. 4. Repeat the rmware upgrade procedure. 5. After the upgrade procedure completes, power off the switch, remove the jumper cap from J17, close the housing, and power the GCS1204 on again.

  • IOGear GCS1204, 8 9 No. Component Description 1 Port Select Pushbuttons Press a pushbutton for longer than two seconds to bring the KVM, USB, and audio focus to the computer attached to its corresponding port. 2 Port LEDs The Port LEDs are located below the Port selection buttons The upper ones are the KVM port LEDs and the lower are the USB LEDs KVM: Lights Dim Orange to indicate the computer attached to the port is on line. It changes to bright Orange when the port is selected and ashes to indicate auto scan has been activated. USB: Lights dim green to indicate a USB connectio

  • IOGear GCS1204, 30 31 PC Keyboard Sun Keyboard [Ctrl] [T] Stop [Ctrl] [F2] Again [Ctrl] [F3] Props [Ctrl] [F4] Undo [Ctrl] [F5] Front [Ctrl] [F6] Copy [Ctrl] [F7] Open [Ctrl] [F8] Paste [Ctrl] [F9] Find

  • IOGear GCS1204, 34 35 4. As you select a device in the list, its description appears in the Device Description panel. 5. After you have made your device selection(s), Click Next to perform the upgrade. If you enabled Check Firmware Version, the Utility compares the device’s rmware level with that of the upgrade les. If it nds that the device’s version is higher than the upgrade version, it brings up a dialog box informing you of the situation and gives you the option to Continue or Cancel. If you did not enable Check Firmware Version, the

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 FMI (V)S36 Series Owners manual and installation manual fmi/v-s36-series-Q83.pdf 06 Sep 2022 20 1.66 Mb
2 Magellan RoadMate 1212 - Automotive GPS Receiver Manuel d'utilisation magellan/roadmate-1212-automotive-gps-receiver-9SA.pdf 18 Jul 2023 62
3 Bryant 574B User's information manual bryant/574b-C96.pdf 23 Sep 2022 4
4 Kenmore 110.7/6832 Quick start manual kenmore/110-7-6832-1CS.pdf 24 Jun 2023 4
5 Campbell Hausfeld HVLP Operating instructions & parts manual campbell-hausfeld/hvlp-1W1.pdf 05 Apr 2023 10
6 EverFocus EHA-SRX Operation & user’s manual everfocus/eha-srx-A86.pdf 04 Nov 2022 8 0.24 Mb

Similar Resources:

  • Elabs

    HS103

    (4 pages)
    LAUNAM NOITCURTSNIHDMI SwitchHS103CE labs can support many areas of your audio and videodistribution needs.We manufacture: • Digital Signage software and Media Players • HD Matrix Switchers • RF amplifiers • HDMI and Component HD distribution amplifiers • CAT 5 Signal Extenders • VGA Extenders and Splitters • and cables of all types.WARR …
  • Black Box

    LGB5028A

    (44 pages)
    LGB5028A Installation and Getting Started GuideBL A C K B OX®Network Administrator’s Installation and Getting Started Guide The switches provide 24 or 48 ports of Gigabit connectivity plus 4 10G ports.24 + or 48 + 4-Port Gigabit Managed Switch with SFP+ 10GLGB5028ALGB5052AOrder toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)FR …
  • Extron electronics

    SW6 AV MX

    (2 pages)
    1-2 SW 6 CV MX, SW 6 SV MX, SW 6 SA MX, SW 6 AV MX, SW 6 SV A MX • SpecificationsSpecifications — SW 6 CV/SV/SV A/SA/AV MX SwitchersVideoGain ............................................... UnityBandwidth .................................... 30 MHz (-3dB)Differential phase error .............. 0.01º, 4.43 to 30 MHzDifferential gain error .............. …
  • 3Com

    3C510510B

    (8 pages)
    Related Standards The Hub TR has been designed to conform to the following standards: Physical Electrical Hub TR EnvironmentalTECHNICAL INFORMATIONFunctional IEEE 802.5Safety UL 1950, EN 60950:92, CSA 22.2 #950EMC FCC 20780, Part 15J, Class A VFG243 Level A (with shielded cable) EN55022 Level ACSA 108.8, CEWidth 17.3 in. Depth 12 in. Height 2 5/8 in. Weight …
  • NEC

    EXPRESSSCOPE Engine 3

    (105 pages)
    NEC Express Server Express5800 Series EXPRESSSCOPE Engine 3 User’s Guide 1. Overview 2. Configuring the Host System 3. Configuring a Management PC 4. Networking 5. Using Remote Management 6. Command Line Interface 7. WS-Management (Web Service for Management) 8. Troubleshooting 4th Edition Jun, 2012© NEC Corporation 2011-2012 …
  • KYLAND Technology

    Aquam8512

    (357 pages)
    Aquam8512 Industrial Ethernet Switches Web Operation Manual Publication Date: May 2015 Version: V1.0 …

Comments, Questions and Opinions: