JVC DT-V17G1 Instructions Manual
|
26 • For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed, and may be slightly different from actual products. • Design and specifications are subject to change without notice. • All company names and product names mentioned herein are used for identification purposes only, and may be the trademarks or re
JVC DT-V17G1, 21 ENGLISH <Functions controlled by the MAKE/TRIGGER system> Display Functions to be controlled Opening Short-circuiting TALLY SEL Selects the color of the tally lamp. Green Red SDI 1 Changes the input to “SDI 1.” Invalid Valid SDI 2 Changes the input to “SDI 2.” Invalid Valid DVI Changes the input to “DVI.” Invalid Valid COMPONENT Changes the input to “COMPO.” Invalid Valid VIDEO Changes the input to “VIDEO.” Invalid Valid 3G-B.DS Selects the “3G SDI LEVEL B” data stream. DS 1 DS 2 DUAL LINK Turns on or off “SDI DUAL LINK.”
JVC DT-V17G1, 13 ENGLISH Operation guide Shows the buttons for each operation. • The menu automatically disappears in about 30 seconds after the previous operation. • Some items may not appear on the menu depending on the input or the input signal. • The items controlled by the MAKE system do not appear on the menu. Setting of “AREA MARKER”, “SAFETY MARKER”, “R-AREA MARKER”, “R-SAFETY MARKER” The setting values and features are as follows. OFF: Deactivate the marker. LINE: Displays the area with an outline. HALF: The area outside the specified aspect ratio of the screen
JVC DT-V17G1, 25 ENGLISH 7 Self-check program This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes troubleshooting easier. Whenever a problem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the problem. When the screen goes blank, and one or some of the INPUT SELECT lamps (DVI, COMPO., VIDEO) on the front control panel start flashing... 1 Check which lamps are flashing. 2 Press button to turn off (on standby) the monitor. 3 Turn off the POWER switch and DC switch on the rear panel. 4 When the AC power supply is used: Di
JVC DT-V17G1, 22 7 Using the serial communication You can control the monitor from a personal computer etc. via the RS-485 or RS-232C terminal. • Consult your dealer for the details of the external control specification. <Communication specifications> Input terminal Cable Terminal specification Communication specifications RS-485 A straight LAN cable ☞ See below Baud Rate: 4800 bps Data Bits: 8 bits Parity: No parity Stop Bits: 1 bit Flow Control: No control Communication Code: ASCII Code RS-232C A straight cable with a D-sub 9-pin connector (male for the monitor, female for the personal computer etc.) <Specifications o
JVC DT-V17G1, 15 ENGLISH SCOPE SETTING* 1 Settings for the wave form monitor and vector scope Item To do Setting value GAIN Adjust the gain level for the incoming wave form data. –10 – +10 SIZE* 2 Select the size of the wave form monitor and vector scope window. NORMAL, LARGE POSITION* 2 Select the position of the wave form monitor and vector scope window. 1 (lower right), 2 (lower left), 3 (upper left), 4 (upper right) TRANSPARENT Activates/deactivates the function to make the window translucent. ON (translucent), OFF (normal) AUTO OFF Activates/deactivates the function to make the wave form monitor and vector scope window go off automat
JVC DT-V17G1, 27 ENGLISH Specifications (cont.) * at the higher position ** at the lower position 7 Dimensions Unit: mm (inch) <Front view> <Side view> <Rear view> 100 VESA mounting holes (Size: 4-M4, depth: 10 mm) 100115 (4 5/8) 240 (9 1/2) 430 (17) 309 (12 1/4) 349.8 (13 7/8)*/314.5 (12 1/2)** 199 (7 7/8) 1.3 (1/16) 102 (4 1/8) 56 (2 1/4) 18 (3/4) 3 (1/8) DT-V17G1_EN.indd 27DT-V17G1_EN.indd 27 09.12.3 7:55:24 PM09.12.3 7:55:24 PM
JVC DT-V17G1, 6 Daily Operations / Connections 7 Front panel q SCREENS CHECK button/lamp Displays only the selected element (R, G, or B) of the video signal. • Each time you press this button, the picture changes in the following order. w ASPECT button/lamp Changes the aspect ratio of the picture from 4:3 to 16:9 when the picture of 16:9 aspect ratio is squeezed into 4:3 format signal. • To return to 4:3, press the button again. • This function does not work when displaying the picture in the 1:1 mode.
JVC DT-V17G1, Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety. European representative of Victor Company of Japan, Limited is: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Germany Information for Users on Disposal of Old Equipment [European Union] This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of- life. Instead, the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment, recove
JVC DT-V17G1, 10 Daily Operations / Connections (cont.) 7 Available signals Video signals No. Signal name Signal format shown in the status display (☞ page 7) Input terminal VIDEO COMPO.(Analog component)* 1 E. AUDIO SDI (IN 1, IN 2)* 2 DVI-D (HDCP) (Digital component/digital RGB) SD/HD (1.5G) 3G SDI DUAL LINK 1 NTSC NTSC √ ———— — 2 PAL PAL √ ———— — 3 B/W50 B/W50 √ ———— — 4 B/W60 B/W60 √ ———— — 5 480/60i 480/60i — √√ —— √ 6 480/59.94i 480/59.94i — √√ —— √ 7 576/50i 576/50i — √�
JVC DT-V17G1, 14 Operation guide Shows the buttons for each operation. • The menu automatically disappears in about 30 seconds after the previous operation. • Some items may not appear on the menu depending on the input or the input signal. • The items controlled by the MAKE system do not appear on the menu. AUDIO SETTING Settings for the audio output balance, EMBEDDED AUDIO signals and level meter Item To do Setting value BALANCE Adjust the balance between the right and left speakers. L5 – L1, 0, R1 – R5 E.AUDIO GROUP* 1 Select the audio channel group of the EMBEDDED A
17 ENGLISH Operation guide Shows the buttons for each operation. • The menu automatically disappears in about 30 seconds after the previous operation. • Some items may not appear on the menu depending on the input or the input signal. • The items controlled by the MAKE system do not appear on the menu. SIZE/POSI. ADJ. Adjusts the size and position of the p
18 REMOTE SETTING Settings for the external control Item To do Setting value SERIAL TYPE Select the input terminal used for external control by serial communication. RS232C, RS485 PARALLEL TYPE Select the external control method for the MAKE/ TRIGGER terminal. MAKE, TRIGGER, SET PIN1 PIN2 PIN3 PIN4 PIN5 Assign the control functions to the pins of the MAKE/ TRIGGER terminal. • Assign a func
JVC DT-V17G1, 16 FUNCTION SETTING Settings for the sub menu display, color system, color of the tally lamp, intensity of the button lamps and the PHASE adjustment. Item To do Setting value sub menu POSI. Select the contents and displaying position of “sub menu.” ☞ “NOTE” COLOR SYSTEM Select the color system. • If the picture is unstable with “AUTO,” select “PAL” or “NTSC.” AUTO, NTSC, PAL TALLY SELECT Select the color of the tally lamp. GREEN, RED DIMMER Select the intensity of the button lamps. NORMAL, DARK COMPONENT PHASE Deactivates the function of PHASE a
2 • Do not install this product in the following places: – in a damp or dusty room – where the product is exposed to soot or steam, such as near the cooking counter or a humidifier – near heat sources – where condensation easily occurs, such as near the window • Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious in
JVC DT-V17G1, 19 ENGLISH Setting value: OFF, VOL.LOCK, ALL LOCK CONTROL LOCK Settings for disabling the buttons on the front panel. • The following operations are not available when “VOL.LOCK” is selected. – VOLUME adjustment knob – Picture adjustment knob • The “ALL LOCK” function disables to control the buttons on the front panel. But following operations are available. – Turning on/off (on standby) the monitor – Displaying the SET-UP MENU (by pressing button while holding button) and turning “CONTROL LOCK” to “OFF” – Operating the monitor by an external control
JVC DT-V17G1, 12 Menu Configuration—MAIN MENU PICTURE FUNCTION Setting for the picture quality Item To do Setting value APERTURE FREQ.* 1 Select the frequency of the luminance signal compensated in “APERTURE LEVEL.” OFF, LOW, HIGH APERTURE LEVEL* 1 Compensate the frequency response of the luminance signal of the video signal. 01 – 10 CTI Adjust the clearness of the outlines of the chrominance signal. OFF, NORMAL, HARD LTI Adjust the clearness of the outlines of the luminance signal. OFF, NORMAL, HARD I/P MODE Selects a proper mode corresponding to the input picture. NORMAL, CINEMA, FIELD sub menu Display the sub menu which enables you to a
JVC DT-V17G1, INSTRUCTIONS DT-V17G1 MULTI FORMAT LCD MONITOR Table of Contents Safety Precautions .............................................. 2 IMPORTANT SAFEGUARDS ........................... 2 Installation ............................................................ 4 Daily Operations / Connections ......................... 6 Front panel ....................................................... 6 Rear panel ........................................................ 8 Available signals ............................................. 10 Menu Configuration—MAIN MENU .................
JVC DT-V17G1, 9 ENGLISH To detach the cover AC IN terminal Case Cover 231 CAUTION • Use only the provided screws. • Make sure the plug will not be pulled out after the cover is attached to the case. Attaching the power cord holder The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal. • The power cord holder consists of two parts, a case and a cover. p DC IN 12V terminal DC 12 V (maximum DC 17 V) power input connector. • While using both the AC and DC 12 V power supply, AC power supply is preferentially used. If the AC power supply is cut off (for example, when turning off the POWER switch), the power suppl
JVC DT-V17G1, 24 Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult an authorized dealer or service center. Symptom Probable cause and corrective action Page No power supply • Press the button. • Turn on the POWER switch or DC switch on the rear panel. • Firmly insert the AC power plug or DC 12 V power plug. • When using a DC 12 V power supply, charge the battery or replace it with a charged one. 6 8, 9 8, 9 9 No picture with the power on • Select the correct input us
JVC DT-V17G1, 5 ENGLISH To adjust the stand height To change the stand height, detach the stand from the monitor. (☞ “To detach the stand” on page 4) Then, change the position of the stand plate according to the stand height you want by choosing the screw holes to use. Screw holes for higher position Screw holes for lower position Stand plate Stand plate <Higher position> <Lower position> To prevent an accidental fall Fix the monitor to a wall by using strings. Fixing the monitor Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two holes on the upper side) using M4 x 10 mm screws (not provided). Bind the
JVC DT-V17G1, 23 ENGLISH <Basic command list> No. Commands Functions Data 1 ! * ** 1 B C N 1 Cr Starts communication (connection) No data 2 ! * ** 1 B C N 0 Cr Terminates communication (termination) No data 3 ! * ** 1 BIDSETxx* 2 Cr Assigns the control ID 01 – 99 4 ! * ** 1 B I D R E T Cr Initializes the control ID No data 5 ! * ** 1 BIDDSPxx* 2 Cr Displays/hides the ID 00: Hide, 01: Display 6 ! * ** 1 BIDCHKxx* 2 Cr Flashes/hides the selected ID No. of the monitor 00: Hide, 01: Display 7 ! * ** 1 B M E N U Cr Displays the MAIN MENU/Quits the menu operation No data 8 ! * ** 1 BUPCr Moves the cursor upward
JVC DT-V17G1, 7 ENGLISH If you press the INPUT SELECT button (☞ t on page 6) currently lit, the status of the input signal and setting of muting are displayed for about 3 seconds. • Make the setting to display/hide the status in “STATUS DISPLAY” of the “INFORMATION” (☞ page 18). • When “STATUS DISPLAY” is set to “AUTO” or “ON,” the status below is also displayed in the following cases: – When you change the input – When the signal condition of the current input changes – When you turn on the monitor • When “STATUS DISPLAY” is set to “ON,” the signal format will remain displayed 3 seconds afte
JVC DT-V17G1, 4 Installation CAUTION • Do not rest your arm on the monitor or lean against the monitor. • Do not touch the LCD panel when installing the monitor. • Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury. You can place the monitor in the following two ways when using it on the supplied stand. When the stand plate is attached to the higher position of the stand body (☞ “To adjust the stand height” on page 5), you can place the monitor as illustrated below. 1 Remove the screws on the right side of the stand (see the illustration below), then lift the stand up by about 144°. 2 Attach the remo
JVC DT-V17G1, 20 External Control 7 About the external control This monitor has three external control terminals. • MAKE/TRIGGER terminal (RJ-45): The following external control systems are available. (1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it. (2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the corresponding pin terminal. ☞ “Using the MAKE/TRIGGER system” on the right • RS-485 terminals (RJ-45): Controls the monitor with the RS-485 system. (☞
JVC 0110SKH-MW-MT Monitor Instructions manual
0110SKH-MW-MT |
JVC KV-M705 Monitor Instructions manual
KV-M705 |
JVC KW-AV58 Monitor Instructions manual
KW-AV58 |
JVC DT-E17L4G Monitor Instructions manual
DT-E17L4G |
JVC GD-F46L1 Monitor Brochure & specs
GD-F46L1 |
JVC KW ADV790 - DVD Player With LCD Monitor Monitor Instructions manual
KW ADV790 - DVD Player With LCD Monitor |
JVC Color Video Monitor TM21A2U Monitor Instructions manual
Color Video Monitor TM21A2U |
JVC BM-H1310SU - Color Production Monitor Monitor Instructions manual
BM-H1310SU - Color Production Monitor |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Shure | BG 4.1 | User giude | shure/bg-4-1-715.pdf | 05 Jan 2023 | 15 | 0.26 Mb |
2 | Boss | 625CA | Operation & user’s manual | boss/625ca-41U.pdf | 25 Feb 2023 | 17 | 2.05 Mb |
3 | JVC | G300 - KD Radio / CD | Instruction manual | jvc/g300-kd-radio-cd-U9I.pdf | 27 Feb 2023 | 111 | |
4 | Vermeiren | Sagitta | Manual | vermeiren/sagitta-HVF.pdf | 06 Nov 2022 | 120 | |
5 | Nilfisk-ALTO | Floortec 560 B | Gebruiksaanwijzing | nilfisk-alto/floortec-560-b-C7L.pdf | 11 Mar 2024 | 18 | |
6 | WHITE BROWN | S 134 | Operation & user’s manual | white-brown/s-134-4EL.pdf | 25 Nov 2023 | 6 | 0.95 Mb |
Absen
Leading LED ApplicationsXD6 / XD10SMD HD OUTDOOR LED DisplayHIGH DEFINITIONFRONT & REAR SERVICINGWIDE VIEWINGANGLEEASY MAINTENANCENOISE FREEHIGH IP RATINGADVANCED TECHNOLOGYSMART MONITORING
…
XD6(4 pages) |
Eizo
Copyright © 2017 EIZO Corporation. All rights reserved.00N0N052A1SUG-EV2785-61st Edition-October, 2017 Printed in Japan.Hinweise zur Auswahl des richtigen Schwenkarms für Ihren MonitorDieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörigeSchwenkarm verwendet wird, muss statt dessen ein geeigneter anderer …
FlexScan EV2785(4 pages) |
Setra Systems
Setra Local DisplayModel LD330Installation and Operating Instructions.Setra’s Model LD330 is a small local display designed for convenientin-line installation. It can be used with voltage output and current output tranducers4-pin bayonet connectors (which meet dimensional requirements of MIL-C-26482and the MIL STD 3116) Amp jack, 15 Pin and9 Pin D-Sub con …
LD330(4 pages) |
Canon
The Visual Professionals.The Visual Professionals.V8000HDe MONITORUser Guide 3903 Stoney Brook Dr. Houston TX 77063Tel: 1.713.272.8822Fax: [email protected]© 2008 ikan Corporation. All right reserved.
…
Monitor V8000HDe(4 pages) |
Mitsubishi
64.5" LCD Display MonitorMODELBefore use- Please be sure to read the “Safety Precautions.” They are important to use this LCD display monitor. - Please check the content of the package. This document contains instructions for World Wide model and Japan model, but their accessories are different.
…
MDT652S(59 pages) |
Eversan
www.eversan.comMODEL 9795HOCKEY SCOREBOARDInstruction ManualAddress: 34 Main Street, Whitesboro, NY 13492Phone: 315-736-3967 • Toll Free: 800-383-6060 • Fax: 315-736-4058SCOREBOARDS • TIMERS • MESSAGE SIGNS • VIDEO DISPLAYS • WIRELESSEVERSANINC.SYNERGYTMreso urces
…
9795(12 pages) |
Cabletron Systems Network Card T2015Network Card Installation manual (Cabletron Systems T2015) T2015, 40 |
Acksys Gateway ETHERNET TO Wi-Fi GATEWAYSAcksys ETHERNET TO Wi-Fi GATEWAYS User Guide (Operation & user’s manual), @WQ57IF ETHERNET TO Wi-Fi GATEWAYS, 141 |
EUTECH INSTRUMENTS Other STANDARD PHSCAN 1 PH TESTEREUTECH INSTRUMENTS Product User Manual: STANDARD PHSCAN 1 PH TESTER PDF Specifications - C2H3D7 STANDARD PHSCAN 1 PH TESTER, 1 |
Sharp Accessory PW-A9200#1T69J1 PW-A9200: Sharp Accessory Owner Documentation PW-A9200, 2 |
ZyXEL Communications Adapter omni.netZyXEL Communications omni.net User Guide (Quick start manual), @RLR296 omni.net, 53 |
Mitsubishi Projector X80Mitsubishi Product User Guide: X80 PDF Brochure & specs - 7C69Q9 X80, 2 |
Mazda Automobile 2002 MPV2002 MPV (Automobile ePDF Manual, #3K8PH3) 2002 MPV, 304 |
Maytag Washer MHWE301Maytag MHWE301 Washer Use & care manual MHWE301, 48 |
KitchenAid Dishwasher KUDK03CTKUDK03CT (Dishwasher ePDF User Guide, #184N6M) KUDK03CT, 1 |
Interacoustics Hearing Aid Affinity2.0Interacoustics Hearing Aid Affinity2.0 Quick manuals Affinity2.0, 96 |
ProForm Other 585 Perspective TreadmillUser Manual: ProForm 585 Perspective Treadmill (SYUPK4, Upd.11th Sep 2023) 585 Perspective Treadmill, 36 |
ViewSonic TV N4000WPN4000WP Brochure - 6F89LV N4000WP, 2 |