JVC MX-D602T Instructions Manual

Text of JVC MX-D602T User Guide:

• JVC MX-D602T, 12 3. Use MULTI CONTROL to adjust to any Sound Mode desired. Press 4 P. DOWN or ¢ P. UP on the MULTI CONTROL to select the tone range you want to adjust. You can adjust “LOW”, “MID” or “HIGH” tone. Press 1 TUNING DOWN or TUNING UP ¡ on the MULTI CONTROL to adjust the level. The level can be adjusted between –3 and +3 in 7 steps. 4. Press SET. “MANUAL 1” appears on the display. 5. Press 4 P. DOWN or ¢ P. UP on the MULTI CONTROL to select the MANUAL number for the memory. 6. Press SET again. “MEMORY” appears for 2 seconds. The setting that has been cre

• JVC MX-D602T, 30 CAUTION: If recordings you have made have excessive noise or static, the Unit may be too close to a TV which was on during recording. Either turn off the TV or increase the distance between the TV and the System. Standard Recording This is the basic method for recording any source. The System also has special ways for recording CD to tape, and tape to tape, which save your time and effort, as well as give you some special effects. However, when you need to add a selection to a tape you have made, or are combining selections from several sources on one tape, use the method described below; just substitute the source you want into this procedure, such as a CD or the Tuner. You can

• JVC MX-D602T, 42 SP-D602 —————————————————————————— Type 3-way, 3-speaker bass-reflex type (Magnetically-shielded type) Speaker Tweeter 2 cm (13/16 inches) dome × 1 Midrange 5 cm (2 inches) cone × 1 Woofer 16 cm (6-5/16 inches) cone × 1 Power Handling Capacity 80 W Impedance 6 ohms Frequency Range 46 - 20,000 Hz Sound Pressure Level 87 dB/w • m Dimensions 215 × 315 × 271 mm (W/H/D) (8-1/2 × 12-7/16 × 10-11/16 inches) Mass 3.3 kg (7.3 lbs) SP-DS90 —————————————————————————— SP-DSC90 (Center Speaker) Type Full range

• JVC MX-D602T, 10 CAUTION: The Volume cannot be adjusted while the Unit is on STANDBY. DO NOT turn on the Unit and/or start playing any source without setting the VOLUME control to 0; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones. For private listening Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones. Balance Adjustment ———————————————————— You can use the Remote Control to adjust the left and right balance of the speakers. 1. Press SHIFT. 2. Press BALANC

• JVC MX-D602T, 5 CAUTION: Make all connections before plugging the Unit into an AC power outlet. Connecting the Speakers For each speaker, connect one end of the speaker wire to the speaker terminals on the back of the System. 1. Open each of the terminals and insert the speaker wires firmly, then close the terminals. 2. Connect the red (+) and black (–) terminals of the right side speaker to the red (+) and black (–) terminals marked RIGHT on the System. Connect the red (+) and black (–) terminals of the left side speaker to the red (+) and black (–) terminal

• JVC MX-D602T, 21 Loading CDs 1. Press 0 on the CD Player you want to insert the disc onto. “OPEN” appears on the display and the disc tray slides out. COMPU PLAY When 0 is pressed while the power is on standby, the power is automatically turned on. 2. Place a CD, with its label side up, onto the tray. ATTENTION: To avoid malfunctions when you play a CD, set the CD in the right place at the center of the tray. 3. Press 0 to close the tray. “CLOSE” appears on the display. 4. Repeat steps 1 to 3 to insert other discs onto the ot

• Warnings, Cautions and Others CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral trian

• JVC MX-D602T, 24 3. Press the number keys (1 to 10 and +10) to select the tracks. The indications on the display stop flashing and remains lit. The selected track numbers light up and the step number appears on the display. • Example: For track 5, press 5. For track 15, press +10 then 5. For track 20, press +10 then 10. For track 32, press +10 three times, then 2. 4. Repeat steps 2 to 3 to select the other tracks for the program. 5. Press 3. The Unit plays the tracks in the order you have programed them. If you try to program a 33rd track, “FULL” will appear on the

• JVC MX-D602T, 8 Common Operations DISC DISC DISC PROGRAM /RANDOM REPEAT EDIT S.A. BASS VOLUME STANDBY indicator AUX PHONES Display SOUND MODE indicator Source, Sound Mode Volume level etc. When the System is being used, the display shows other items as well. However, we have only shown the items described in this section. Demo Mode When the System is connected to an AC power outlet, a Demo automatically starts showing some of the system’s features. The Demo display cycles through the following items repeatedly. • Scrolling display of “DEMO MODE START”. • Demo of PRO LOGIC and 3CH LOGIC. • Demo of Sound Modes. • Demo of S.A. BASS. • Demo of

• 19 On the Remote Control To tune in FM stations, press FM. To tune in AM stations, press AM. COMPU PLAY When FM or AM is pressed while the power is on standby, the power is automatically turned on. Three Ways to Select a Station —————————————— Press 1 TUNING DOWN or TUNING UP ¡ on the MULTI CONTROL repeatedly to move from frequency to frequency until you find the one

• JVC MX-D602T, 11 Sound Modes The System has some preset sound effects that give you control of the way your music sounds, so you can tailor it for your room and for the quality of the source. We can give you some idea of how each one affects the music, but the only way to really tell is to try them yourself. You can also create up to three of your own customized S.E.A. (Sound Effect Amplifier) settings and store them in the Unit’s memory (MANUAL 1, MANUAL 2, MANUAL 3). The preset sound modes include modes using surround effects and modes using S.E.A. effects. Sound Mode effects cannot be recorded. To get an effect, press SOUND MODE repeatedly until the

• 22 On the Remote Control Press CD CONTROL then press 3. The source is set to CD and play starts from the first track of the currently selected CD whose disc number shown on the CD indicator. • If the above operation is carried out while the power is on standby, the power is automatically turned on. Press DISC (1 to 3) of the disc you want to play. The sour

• JVC MX-D602T, 44 Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous. The JVC service and engineering organization stands behind our products. NATIONAL HEADQUARTERS JVC SERVICE & ENGINEERING COMPANY OF AMERICA DIVISION OF US JVC CORP. 107 Little Falls Road Fairfield, NJ 07004-2105 If you ship the product • • • Pack your JVC unit in the original carton or one of equivalent size and strength. Enclose, with

• JVC MX-D602T, 2 Table of Contents Features...................................................................... 1 How This Manual Is Organized................................. 1 IMPORTANT CAUTIONS .......................................1 Getting Started ................................................ 3 Accessories ................................................................3 How to Put Batteries in the Remote Control ............. 3 Using the Remote Control .........................................3 Connecting the FM Antenna...................................... 4 Connecting the AM Antenna ........

• 36 CAUTION: If the Unit is unplugged, or a power failure occurs, the timer setting will be erased in a few days. If the settings are erased in this way, reset the timer settings. Setting the Recording Timer With the Recording Timer you can make a tape of a radio broadcast automatically whether or not you are home. For the timer to work correctly, you need to make sure o

• 7 COMPU PLAY COMPU PLAY is JVC’s feature that lets you control the most frequently used functions of the System with a single touch. One Touch Operation starts playing a CD, turns on the radio, plays a tape, etc. with a single press of the play button for that function. What One Touch Operation does for you is to turn the power on, then start the function you have specified. If

• JVC MX-D602T, 20 Using the CD Player DISC DISC DISC PROGRAM /RANDOM REPEAT EDIT PROGRAM/RANDOM REPEAT 7 STOP CD £/8 When CD is selected as the source, the button lights up. DISC buttons 0 Disc Trays FM AM RM-SED602TU REMOTE CONTROL VOLUME + – TAPE A AUX REC PAUSE TAPE B DIRECTION REPEAT SLEEP SHIFT TEST TONE CENTER MODE DELAY TIME L BALANCE R CENTER LEVEL 3CH LOGICPRO LOGIC S.A.BASS SOUND MODE DISC 1 CD CONTROL TAPE CONTROL DISC 2 DISC 3 FM MODE –+ REAR LEVEL –+ POWER CD Player control buttons Number keys Display Disc indicator Track number, Playing time,

• JVC MX-D602T, 29 Using the Cassette Deck (Recording) DISC DISC DISC PROGRAM /RANDOM REPEAT EDIT CD REC START REC START/STOP DUBBING FM AM RM-SED602TU REMOTE CONTROL VOLUME + – TAPE A AUX REC PAUSE TAPE B DIRECTION REPEAT SLEEP SHIFT TEST TONE CENTER MODE DELAY TIME L BALANCE R CENTER LEVEL 3CH LOGICPRO LOGIC S.A.BASS SOUND MODE DISC 1 CD CONTROL TAPE CONTROL DISC 2 DISC 3 FM MODE –+ REAR LEVEL –+ POWER REC PAUSE Things to Know before You Start Recording ——————— It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs witho

• JVC MX-D602T, 26 The Cassette Deck allows you to play, record and dub audio tapes. With Automatic Tape Detection, you can listen to Type I or II tapes without changing any settings. The use of tapes longer than 120 minutes is not recommended, since characteristic deterioration may occur and these tapes easily jam in the pinch-rollers and the capstans. Entering the TAPE Operation Mode with the Remote Control Pressing TAPE CONTROL makes the Remote Control ready for the Cassette Deck operations. Operate the Cassette Deck with 3, 7 and MULTI CONTROL. The explanation provided in “Using the Cassette Deck” section assumes that the Remote Control has been

• JVC MX-D602T, 23 Programing the Playing Order of the Tracks You can change the order in which the discs and tracks play, and select only the discs and tracks you want from among those loaded in the CD Player. You can program up to 32 steps in any desired order from among the discs in the CD player. You can only make a program when the CD Player is stopped. On the Unit 1. Press PROGRAM/RANDOM. “PROGRAM” appears on the display and the PROGRAM indicator lights up. If you have already created a program, the last step of the previous program will appear on the

• JVC MX-D602T, 39 Care and Maintenance Compact Discs Handle your compact discs, cassette tapes, and Cassette Deck carefully, and they will last a long time. • Remove the CD from the case by holding it at the edges while pressing the center hole lightly. • Do not touch the shiny surface of the CD, or bend the CD. • Put the CD back in its case after use to prevent warping. • Be careful not to scratch the surface of the CD when placing it back in the case. • Avoid exposure to direct sunlight, temperature extrem

• JVC MX-D602T, 32 5. Press SET. The tracks to be recorded on side B appear on the display. • Each time you press the button, the tracks to be recorded on side A and side B appear on the display alternately. 6. Insert a blank or erasable cassette in Deck B. When you want to record on both sides of a tape, press REVERSE MODE to turn Reverse mode on. 7. Press CD REC START . The Unit plays the CD and starts recording. If the tape has not been rewound, the Unit rewinds the tape before starting to record the CD. To stop at any time while recording, press 7 STOP or REC START/STOP on the Unit. If 7 STOP is pressed, the Cassette Deck will create a four-second blank space after the CD Player stops. If

• JVC MX-D602T, 3 Getting Started Accessories Check that you have all of the following items, which are supplied with the System. AM Loop Antenna (1) Remote Control (1) Batteries (2) FM Wire Antenna (1) If any of these items is missing, contact your dealer immediately. How to Put Batteries in the Remote Control Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment. CAUTION: Handle batteries properly. To avoid battery leakage or explosion: • Remove batteries when the Remote Control will not be used for a long time. • When you need to replace t

• JVC MX-D602T, 1 Easy operation Great sound Triple Tray Thank you for purchasing the JVC Compact Component System. We hope it will be a valued addition to your home, giving you years of enjoyment. Be sure to read this instruction manual carefully before operating your new stereo system. Here you will find all the information you need to set up and use the system. For questions that are not be answered in the manual, contact your dealer. Features Here are some of the things that make your System powerful and easy to use. The controls and operations have been designed to make them very easy to use, so you can spend your time listening to mu

• JVC MX-D602T, 34 Setting the Daily Timer With this timer you can wake up to music from a CD, tape, your favorite radio program. You can set the Daily Timer whether the Unit is on or off. Procedure For Setting the Daily Timer 1. Press TIMER/CLOCK so that “DAILY” appears on the display. The DAILY indicator flashes on the display. • Each time you press the button, the timer setting indication changes as follows: DAILY = ON TIME (flashes) = REC = ON TIME (flashes) = Clock setting = Canceled (current source) = (back to the beginning) Note: If the clock has not been set, even if TIMER/CLOCK is pr

• JVC MX-D602T, 9 Setting the Clock Before operating the unit, set the correct time. You can set the clock whether the Unit is on or off. 1. Press TIMER/CLOCK. The hour digits begin flashing. 2. Press 4 P. DOWN or ¢ P. UP on the MULTI CONTROL to set the hours. Press ¢ P. UP to increase the hour. Press 4 P. DOWN to decrease the hour. Holding down continuously changes the hour setting more rapidly. 3. Press SET. The minute digits begin flashing. 4. Press 4 P. DOWN or ¢ P. UP on the MULTI CONTROL to set the minutes. Press ¢ P. UP to increase the minutes. Press 4 P. DOWN to decrease the minutes. Holding down continuously changes the

• JVC MX-D602T, 25 Repeating a Track or the Discs You can have all the discs, the program or the individual track currently playing repeat as many times as you like. Press REPEAT on the Unit. Each time you press the button, the Repeat Modes change as follows. = REPEAT ALL = REPEAT 1 = No indicator = (back to the beginning) REPEAT ALL: Repeats all the tracks on the CDs, or all the tracks in the program. REPEAT 1: Repeats one track on one CD. To exit Repeat Mode, press REPEAT until the Repeat Mode indicator on the display goes out. Tray Lock Function In order to safely keep the discs in the CD Player, the three trays can be electronically locked in a single operation. When the Tray Loc

Related Products and Documents (Stereo System):

Comparable Devices:

Similar Resources:

• Sharp CD-CH1000 (80 pages) CD-CH1000 CONTENTSPage IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)...................................................................................................... 2SPECIFICATIONS ............................................................................................................................................................ 2NAMES OF PARTS .... …

• LG DMS5540F (44 pages) www.lg.comENGLISHPlease read this manual carefully before operating your set and retain it for future reference. DM5540(DM5540, DMS5540F/W)OWNER’S MANUALDVD Mini Hi-FiSystemSPK type changed_DM5540-FU_DPHLLLK_2013.12.07.indd 1 2013-12-19  6:56:00 …

• Sharp CD-RW5000 (48 pages) Thank you for purchasing this SHARP product.To obtain the best performance from this product, please read thismanual carefully. It will guide you in operating your SHARP product.CD-RW5000 Audio Tower System consisting of CD-RW5000 (mainunit) and CP-RW5000 (speaker system).AUDIO TOWER SYSTEMMODELCD-RW5000OPERATION MANUAL*RW5000_P01,48(FRONT/BACK) 00.7.1, 4:33 …

• dBTechnologies FlexSys FMX10 (73 pages) MANUALE D’USO – Sezione 1USER MANUAL - Section 1BEDIENUNGSANLEITUNG - Abschnitt 1MANUEL D’UTILISATION – Section 1MANUAL DE USO – Sección 1Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO - Sezione2”.The warnings in this manual must be observed together with the „USER MANUAL - Section 2“.Die in d …

• Behringer Nekkst K8 (13 pages) Quick Start GuideNEKKSTK8/K6/K5Audiophile Bi-Amped 8, 6, and 5" Studio Monitor with Advanced Waveguide TechnologyK10SAudiophile 10" Studio Subwoofer with High Excursion WooferV 4.0 …

• Melco N1A EX (79 pages) Digital Music LibraryN1 EX/N10/N100 SeriesUser ManualThis manual uses sample screenshots captured on firmware version 4.01. Depending on the firmware version that is installed on your Digital Music Library, functions described and screenshots contained in the manual may appear differently, so functions on your product may not work as described in the manual. …

Comments, Questions and Opinions: