Kenwood SPECTRUM 350 Setting Up
|
Kenwood SPECTRUM 350, 21. Warranty Write the serial numbers (they’re on the back of each unit, along with the model number) in the space below. If you need to call your dealer for information or service, you’ll need the model and serial numbers. We suggest you keep your sales receipt as proof of purchase to vali- date your warranty coverage. See the complete text of the warranty below. Please read it carefully. Model number Serial number KR-596 DP-R896 KX-W595 JL-506 Kenwood Limited Warranty Spectrum Systems Kenwood
Kenwood SPECTRUM 350, You can increase or decrease the volume level in 1 decibel (dB) increments. The display shows the decibel level change. Adjusting from the front panel Turn the VOLUME knob clockwise to increase the volume. Turn the knob counter-clockwise to decrease it. Adjusting from the remote Press the VOLUME buttons to increase or decrease the volume level. Adjusting the volume 13. Selecting the input source You can play audio from as many as 5 different sources, including: • TUNER • CD • PHONO • TAPE • VIDEO Selecting from the front panel Rotate the INPUT SELECTOR knob until you see the input source you want on the di
Tuning stations automatically You can automatically find the strongest radio station signals. 1 Select the TUNER input. 2 Press the BAND button to select FM or AM. 3 Press the AUTO/MANU button to select AUTO. The AUTO indicator light turns ON. 4 On the TUNING buttons, press G to move up the broadcast band, or H to move down the broadcast band. The tuner stops automatic
Kenwood SPECTRUM 350, 31. Using the cassette deck The front panel controls and display 30. / II / II B RECORDING/PLAYBACKAPLAYBACK ONLY REC PLAY REW FF STOP/EJECT PAUSEPLAY REW FF STOP/EJECT PAUSE STEREO DOUBLE CASSETTE DECK KX-W595 ON STANDBY POWER REC LEVEL DOLBY NR DUBBING TAPE SELECTOR ON OFF ON OFF HIGH NORMAL REC DUBBING )VWX PEAK LEVEL METER (dB) –∞ –5 0 +3 +6 PLAY button REWIND button FAST FORWARD button STOP/EJECT button PAUSE button DOLBY NR button DUBBING button POWER button RECORDING LEVEL knob TAPE
Kenwood SPECTRUM 350, Safety First. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Welcome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Did you get everything?. . . . . . . . . . . . . . . . . . . . 6 You may need to purchase. . . . . . . . . . . . . . . . . 6 You’ll need these tools. . . . . . . . . . . . . . . . . . . . . 6 Assembling the rack. . . . . . . . . . . . . . . . . . . . . . . 7 How to get replacement parts for your rack . . . . . . . . .
To check a program Press the CHECK button. Each time you press the button, you see the CD and track numbers in the order you programmed them on the display. To resume normal play Press the P.MODE button. After the current track is done, the tracks continue to play in the order on the CD. To stop play Press the STOP button. Adding a track to a program You can add another track to the end of a pr
Kenwood SPECTRUM 350, If you’ve connected all of the power and system control cables as we’ve shown, you can turn on the power to the entire system from the receiver. • Press the power switch on the receiver (or the POWER button on the remote) to turn the entire system ON and OFF. Turning ON the power 19. Important: • Since the CD player and cassette deck have mechanical switches you must press their POWER switches when you turn the system ON for the very first time. After the first time, they will automatically turn ON and OFF with the rest of the system. MULTIPLE COMPACT DISC PLAYER DP-R896 POWER P.MODE T
Kenwood SPECTRUM 350, If the receiver doesn’t respond when you press a button on the remote, you need new batteries. We recommend replacing both batteries at the same time for longer battery life. 1 Remove the cover by pressing down on the ridged area and sliding it off in the direction of the arrow. 2 Insert 2 AA-size alkaline batteries (be sure to pay attention to the (+) and (-) signs when you’re inserting the batteries). 3 Close the cover. Loading and replacing the batteries 11. You can use your SPECTRUM system remote for many functions. A few tips • Depending on temperature, humidity, and other environmen- tal conditions, the operating range of your remote is approxi- mately 30’ and up to 30°
Kenwood SPECTRUM 350, You can repeat a single CD, all loaded CDs, or the contents of a program. Repeating a single CD 1 Press the STOP button. 2 Press the P.MODE button. The PGM light turns ON. 3 Select a CD. 4 Press the P. Mode button. The ALL indicator light turns on. 5 Press the REPEAT button. The REPEAT light turns ON. 6 Press the PLAY button. Repeating all loaded CDs 1 Make sure that the PGM light is OFF. If the PGM light is ON, press the P.MODE button. 2 Press the REPEAT button. The REPEAT light turns ON. 3 If you weren’t already playing CDs, press the PLAY button. Repeating programmed tracks You can repe
Kenwood SPECTRUM 350, Important: Please wait until you’ve connected all of the cables before plugging any of the components into AC wall outlets and turning them on. Connecting your speakers Connect your speakers first. You’ll have an easier time getting to the connections on the backs of the components before you connect all of the other cables. 1 Place the speakers in their approximate locations first, then leave a little extra speaker wire so you can fine-tune their loca- tions. 2 Use the speaker wire supplied wi
Kenwood SPECTRUM 350, Connecting your CD player, cassette deck, and optional turntable or VCR Use the cables that came with the audio and video components. You can connect any turntable that has a magnetic phono cartridge. 13. TAPECD L R REC OUT PLAY IN OUT IN OUT IN SYSTEM CONTROL SPEAKERS (8-16Ω) PHONO ADAPTOR VIDEO FM75Ω LOOP ANTENNA FM300Ω GND ANTENNA LINE OUT L R GND AM L R L R OUT AUDIO IN L R REC PLAY TAPE KR-596 Receiver Cassette Deck CD Player VCR (optional) Turntable (optional) Audio cord
Kenwood SPECTRUM 350, 7. Using the controls Front panel controls 6. AM-FM STEREO RECEIVER KR-596 ■ AUTO TUNING SYSTEM ■ 30 STATION RANDOM PRESET BASS FLAT 22 44 66 88 +10-10 TREBLE FLAT 22 44 66 88 +10-10 ON/STANDBY POWER PHONES STANDBY SPEAKERS SPEAKERS INPUT SELECTOR VOLUME CONTROL DOWN UP BALANCE RL BAND TUNING 1MEMORY AUTO/MANU . +10 2345 6P.CALL 7 8 9 0 POWER button HEADPHONES jack STANDBY indicator REMOTE SENSOR SPEAKERS button VOLUME CONTROL knob INPUT SELECTOR knob TONE CONTROL knobs BALANCE CONTROL button TUNING buttons SPEAKERS indicator BAND SELECTOR button NUMBER buttons AUTO/MANUAL button PRESET CALL button MEMORY button
Kenwood SPECTRUM 350, 9. Step 8 T Screws face toward the inside of the rack Glass door (top) Step 9 Step 10 Step 11 U Top edge of kick panel V W First close the door to see where the magnetic catch contacts it. Attach the cushion to the door where the magnetic catch contacted it. Slip the catch plate over the cushion. W V Slide door into hinge (edge of hinge even with edge of glass) Edge of hinge even with edge of glass
Kenwood SPECTRUM 350, Setting up your SPECTRUM System isn’t difficult, but getting your system up and running will be even easier if you follow the step-by-step direc- tions in this manual. Unpacking Unpack all of the components care- fully, and examine them for shipping damage. If any are damaged or fail to operate, notify your dealer imme- diately. If your SPECTRUM System was shipped to you directly, notify the shipping company without delay. Only the person or company who originally received the system can file a claim against the carrier for shipping damage. K
Kenwood SPECTRUM 350, Using the AM indoor loop antenna (supplied) Place the antenna as far away as possible from the main system, television, speaker wires and power cords. Rotate the antenna until you get the best reception. Using the FM indoor antenna (supplied) Use this antenna until you can install an outdoor antenna. When you do, remove the indoor antenna. 1 Remove the insulation from the wire tip, and twist the wire tightly to get rid of any loose strands. 2 Connect the end of the wire to the left-most antenna jack on the receiver. 3 Fully extend the antenna, and
Kenwood SPECTRUM 350, 9. Reading the display 8. AUTO TUNED STEREO MEMORY FM AM MHz KHz ch MUTING AUTO indicator STEREO indicator MEMORY indicator TUNED indicator BAND indicator FREQUENCY indicator CHANNEL indicator MUTING indicatorVOLUME indicator SPEAKERS indicatorINFORMATION display INPUT SELECTOR indicator L/R BALANCE indicator UPPER (tuner) LOWER (amplifier)
Kenwood SPECTRUM 350, Cassette deck (KX-W595) Format Track system: 4 track, 2 channel Recording system: AC bias (105 kHz) Heads Well-A: Playback head x 1 Well-B: Record/playback head x 1, Erase head x 1 Performance Wow and flutter: 0.3% (WRMS) Fast-wind time: Approx 110 seconds (C-60 tape) Frequency response: Normal tape: 30 Hz ~ 13 kHz, +3 dB High-bias tape: 30 Hz ~ 13 kHz,+3 dB Signal-to-noise ratio: (3% 3rd harmonic distortion, high bias tape): Dolby NR OFF: >57 dB Dolby B NR ON: >66 dB Harmonic distortion (315 Hz, 250 nWb/m, high bias tape): <1% Input sensitivity/impedance: 122.8 mV/47 k-ohms Output level/impedance: 775 mV/3.3 k-ohms General Power
Kenwood SPECTRUM 350, 4. Now that you’ve set up your SPECTRUM system, the real fun begins! Operating your system is easy, if you follow the step-by-step instructions in this manual. Spend a little time with the manual before you jump in, so you become familiar with the many capabilities of your system. You’ll find a handy table of contents to guide you to the information you need. Then put up your feet, sit back and enjoy the fabulous sound of your SPECTRUM system! Welcome 5. Special tapes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Listening to
You can turn the speakers ON or OFF (for example, to use headphones) with the SPEAKERS button. 1 Press the SPEAKERS button (while they are off) to turn the speakers ON. 2 Press the SPEAKERS button again to turn the speakers OFF. The SPEAKERS light on the display turns ON when the speakers are ON, and it goes OFF when then speakers are OFF. You can adjust the balance of the volume between t
Kenwood SPECTRUM 350, 21. Using the CD player The front panel controls and display 20. MULTIPLE COMPACT DISC PLAYER DP-R896 POWER P.MODE TIME DSP RANDOM REPEAT CHECK EDIT MODE CLEAR ON STANDBY /II DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC SKIP OPEN/CLOSE STOP PLAY/PAUSE PGM RANDOM MULTI EDIT 1 2 3 4 5 A B DISC NO. REPEAT TRACK NO. SINGLE ALL P.C. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 POWER button TIME DISPLAY button RANDOM button REPEAT button DISC TRAY SEARCH buttons SKIP buttons PLAY/PAUSE button STOP button OPEN/CLOSE button DISC SKIP buttonDISC SELECTOR buttons (1-5) CLEAR button CHECK button EDIT MODE button (works with Kenwood computer- c
Use the following parts list to identify missing or damaged parts: SRC-406C SRC-406N Item Description Quantity Part No. Part No. A Left side panel 1 XW1061 349092-0 B Rack bottom 1 XW0903 344739-1 C Right side panel 1 XW1060 349093-9 D Kick panel 1 XW0902 344733-2 E Rack top 1 XW0897 344727-8 F Bottom back panel 1 XW0905 433734-4 G Fixed shelf 1 XW0900 344737-5 H Removable shelf 1 XW09
Kenwood KXF-W4030 Stereo System Instruction manual
KXF-W4030 |
Kenwood KR-4070 Stereo System Instruction manual
KR-4070 |
Kenwood CT-203 Stereo System Instruction manual
CT-203 |
Kenwood KDC-3025 Stereo System Instruction manual
KDC-3025 |
Kenwood R-SE7 Stereo System Instruction manual
R-SE7 |
Kenwood KRF-V7020D Stereo System Operation & user’s manual
KRF-V7020D |
Kenwood KR-A3080 Stereo System Instruction manual
KR-A3080 |
Kenwood CT-405 Stereo System Instruction manual
CT-405 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Russound | A-MSS | Manual | russound/a-mss-PJU.pdf | 25 May 2023 | 2 | 3.51 Mb |
2 | Craftsman | 240.74805 | Instruction manual | craftsman/240-74805-197.pdf | 03 Sep 2023 | 12 | 1.5 Mb |
3 | Honeywell | MF08CESWW | Owner's manual | honeywell/mf08cesww-6B4.pdf | 29 May 2023 | 20 | 2.05 Mb |
4 | EVGA | nForce 123-YW-E175 | Operation & user’s manual | evga/nforce-123-yw-e175-J82.pdf | 23 Aug 2023 | 58 | 9.12 Mb |
5 | Epson | PowerLite 825 | Specifications | epson/powerlite-825-8P5.pdf | 03 Jan 2023 | 2 | 2.42 Mb |
6 | BT | RELATE 3000 | Operation & user’s manual | bt/relate-3000-86I.pdf | 24 Nov 2022 | 34 | 0.92 Mb |
Samsung
SLIM DIGITAL HOME CINEMA SYSTEMHT-DS1000HT-DS1100HT-DS1050COMPACTDIGITAL VIDEOInstruction ManualAH68-01544KREV;01THIS APPLIANCE IS MANUFACTURED BY:COMPACTDIGITAL AUDIONA LC HD
…
HT-DS1100(42 pages) |
Sony
ALT-A33PCWireless audio transmitter & receiver Key FeaturesUniversal receiver connects to existing audio setupsUSB S-AIR™ Digital Wireless PC transmitterExpandable with optional S-AIR™ enabled speakersS-AIR™ wireless technology for multi-room listening2 Unique music management softwareKey TechnologiesUniversal receiver The Sony® Wireless Mu …
ALT-A33PC - Wireless Music Transmitter(2 pages) |
Philips
PhilipsMini Hi-Fi SystemCD playbackFWC143Rich sound experienceSet your sights on the attractive FWC143 Mini Hi-Fi System, which delivers superbly rich sound. You'll appreciate how easy it is to operate and control, just sit back, relax and enjoy your music all day, your way!Enrich your sound experience• 2 x 10 W RMS/2 x 20 W music power• Full rang …
FWC143(2 pages) |
Hitachi
CAUTION:Before servicing this chassis, it is important that the service technician read the “Safety Precautions” and “Product Safety Notices” in this service manual.ATTENTION:Avant d’effectuer l’entretien du châassis, le technicien doit lire les «Précautions de sécurité» et les «Notices de sécurité du produit» présentés dans le prése …
AX-M79(44 pages) |
Aiwa
SERVICE MANUALDATABASIC TAPE MECHANISM : 2ZM-1 YR9NFBASIC CD MECHANISM : 3ZG-3 YE3NCCOMPACT DISCSTEREO SYSTEMXR-M500XR-M501S/M Code No. 09-006-345-8R1K(S)EZ(S)REVISIONThis Service Manual is the "Revision Publishing" and replaces "Simple Manual"(S/M Code No. 09-006-345-8T1).
…
XR-M500(42 pages) |
Panasonic
RMS output powerTHD 10%, both channels driven1 kHz 115 W per channel (3 Ω)Total output power 230 WPMPO 2500 Wn FM/AM TUNER, TERMINALS SECTIONPreset station FM 20 stationsAM 15 stationsFrequency Modulation (FM)Frequency range 87.9 to 107.9 MHz (200 kHzsteps)87.5 to 108.0 MHz (100 kHzsteps)Sensitivity 4.0 µV (IHF)S/N 26 dB 2.2 µVAntenna terminal(s) 75 Ω …
SA-AK250PL(102 pages) |
Lenovo Laptop 40625DULenovo Laptop 40625DU Brochure 40625DU, 4 |
Gigabyte Motherboard GA-EG41MF-S2HGigabyte GA-EG41MF-S2H Motherboard Operation & user’s manual GA-EG41MF-S2H, 96 |
Polaris Offroad Vehicle Sportsman 570 EFIPolaris Sportsman 570 EFI Offroad Vehicle Owner's manual Sportsman 570 EFI, 148 |
TuffStuff Fitness Equipment Apollo 7000 SeriesFitness Equipment PDF Owner's manual Apollo 7000 Series, 19 |
RCA Camcorder CC6272CC6272 (Camcorder ePDF User Manual, #ZUVNJ7) CC6272, 2 |
Kyocera Copier FS-C8500DNKyocera FS-C8500DN Manual (Quick installation manual), @9B3531 FS-C8500DN, 16 |
SICK Security Sensors miniTwin2SICK Security Sensors Original instructions manual (File: sick-minitwin2-original-instructions-manual-84, Saturday 07-10-2023) miniTwin2, 84 |
Parkside Pressure Washer PHD 150 D3Parkside PHD 150 D3 Pressure Washer Operation & user’s manual PHD 150 D3, 50 |
Amped Wireless Extender SR20000GPDF Manual (@M6K1B9), Amped Wireless SR20000G Extender (12/10/2023) SR20000G, 2 |
MagicRadar Security System T04#6K9Q62: T04 Security System Owner's manual T04, 98 |
Sharp Calculator EL-9900Manual: Sharp EL-9900 (179W18, Upd.20.01.2024) EL-9900, 20 |
BMW Household Appliance X1 - PRODUCT CATALOGUE#GVH2K9: X1 - PRODUCT CATALOGUE Household Appliance Technical data manual X1 - PRODUCT CATALOGUE, 6 |