Epson C82378 Administrator's Manual

Text of Epson C82378 User Guide:

• Epson C82378, Settings for Windows 2000/NT 6-13 1. Turn on the printer with the network adapter. 2. Run EpsonNet WebAssist by either of the methods described below. ❏ Run EpsonNet WinAssist. Click the printer you want to configure from the list and click Launch Browser . ❏ Open your browser, and type in the IP address of the network adapter directly. Do not run EpsonNet WinAssist. http: // the IP address of the network adapter / 3. Click NetBEUI under Network on the Configuration menu to view the NetBEUI setting screen. NetBEUI: Select Enable . If Disable is on, all NetBEUI related functions stop. NetBIOS Name: Enter the printer’s NetBIOS name which is the computer name on th

• Epson C82378, Installing Protocols A-4 4. Click Protocol , and then click Add . 5. In the Select Network Protocol dialog box, click Internet Protocol (TCP/IP) , and then click OK . 6. Verify that the Internet Protocol (TCP/IP) check box is selected. Then double-click Internet Protocol (TCP/IP) and set the IP address, subnet mask, etc. correctly.

• Epson C82378, The EpsonNet Configuration Utility 10-20 EpsonNet MacAssist menu You can make the IP address settings and AppleTalk settings in the dialog below. See Setting the IP address in Chapter 3 and Chapter 7, Settings for Macintosh for more details. IP Address Configuration: Items Explanations IP Address Setting Select the method of acquiring an IP address. IP Address Enter the IP address for the network adapter. Subnet Mask Enter the subnet mask of the IP address. Default Gateway Enter the gateway.

• Epson C82378, EPSON Status Monitor 2 (Windows only) 12-22 Consumables menu (EPSON Stylus COLOR/EPSON Stylus Photo Series) The information given on the Consumables menu varies according to the printer you are monitoring. Remaining color ink: Shows the amount of color ink remaining. Remaining black ink: Shows the amount of black ink remaining. Remaining paper: Shows the approximate amount of remaining paper. This feature is available only on some printers. Check paper size before: Defines whether the paper size is checked before printing. This feature is not available on all printers. The Consumables menu for the EPSON Stylus COLOR 1520. The Consumables menu for the EPSON Stylus COLOR 3000.

• Epson C82378, x Appendix A Installing Protocols Installing TCP/IP Protocols on Your PC . . . . . . . . . . . . . . . . . . . . A-1 Windows 98/95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 Windows 2000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3 Windows NT 4.0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5 Windows NT 3.51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7 Macintosh (with Open Transport) . . . . . . . . . . . . . . . . . . .

• EPSON Status Monitor 2 (Windows only) 12-10 8. Select Allow monitoring to monitor Windows shared printers. Select Do not allow monitoring to not monitor Windows shared printers. Click Next . Note for Win 98/95: The screen shown below does not appear in Windows 98/95. 9. Check the current settings and click Next . The installation program will start installing t

• Introduction 4 About Functions of Network Adapter ❏ By installing the network adapter into your printer’s parallel interface, network printing becomes available with low cost. ❏ The network adapter automatically selects either 10BaseT or 100BaseTX when it is connected to a network. It supports 100 Base full duplex, 100 Base half duplex, and 10 Base half duplex. ❏ Because the n

• EPSON Status Monitor 2 (Windows only) 12-12 Starting EPSON Status Monitor 2 From Windows 98/95/2000/NT 4.0 Double-click the Status Monitor icon on the right side of the taskbar. You can also start EPSON Status Monitor 2 by clicking Start , pointing to Programs and EPSON , and then clicking EPSON Status Monitor 2 . From Windows NT 3.51 Double-click the EPSON Statu

• Epson C82378, Settings for Windows 2000/NT 6-2 Printing with TCP/IP This section explains how to set up the printer for use in a TCP/ IP environment. Note: ❏ If you have not set the IP address for the network adapter, see “Setting the IP Address Using EpsonNet WinAssist/MacAssist” on page 3-2 for instructions. ❏ Be sure that the TCP/IP protocol is installed in your computer. See “Installing TCP/IP Protocols on Your PC” on page A-1 for instructions. Printing via Standard TCP/IP Port Monitor in Windows 2000 When using the printer on a TCP/IP network in Windows 2000, follow the steps below to connect the network printer to your computer using Standard TCP/IP Port Monitor. Setting u

• Epson C82378, The EpsonNet Configuration Utility 10-30 Password The password set here protects the settings. You will be asked for the password when you update or change the settings on each setting screen. Passwords are case sensitive. No password is set by default. Note: ❏ The same password can be used for EpsonNet WinAssist, MacAssist, and WebAssist. ❏ If you forget your password, you need to initialize the network adapter. See “Initializing the Network Adapter” on page 1-6 for instructions

• Epson C82378, EpsonNet Direct Print Utility 11-13 5. Make the appropriate settings for the desired port. LPR standard printing: Select the LPR Printing check box and then the Standard Printing radio button. Print data is spooled by the computer before sending the print job to the target network printer. LPR enhanced printing: Select the LPR Printing check box and then the Enhanced Printing radio button. LPR enhanced printing sends the print job to the target network printer without spooling all of the prin

• Epson C82378, Settings for NetWare 4-41 Mode: Select Remote printer . Frame type: Select Auto . Do not select other frame types. Tree name: Leave as is. Context: Leave as is. Primary printserver name: Enter the SAP name you created as described page 4-38 (up to 47 characters). Printer port number: Enter the same port number as you set for the print server page 4-38 (from 0 to 254). 6. After making the settings, click OK . The Password dialog box appears. 7. Enter your password (up to 20 characters) and click OK to save settings. If you are entering a password for the first time, click Change and set the password. For more information about passwords

• Epson C82378, EPSON Status Monitor 2 (Windows only) 12-4 Local pinter Connect the printer directly to the printer port of your computer. For Windows 98/95/2000: You need to set the bi-directional support in the printer’s properties dialog box. For Windows 98/95, click the Details tab and click Spool Settings . Then click the Enable bi-directional support for this printer radio button. For Windows 2000, click the Ports tab and check the Enable bidirectional support check box. Note: When you monitor a local printer with Windows 98/95, use LPT1 for the printer port. LPR printer LPR printers

• Epson C82378, Setting the IP Address 3-1 Chapter 3 Setting the IP Address To use the network adapter with TCP/IP, you need to assign it an IP address using EpsonNet WinAssist, EpsonNet MacAssist, or the arp/ping command. The IP address should be set in the following cases: ❏ When configuring the network adapter using EpsonNet WebAssist (the utility that is pre-installed in the network adapter) ❏ When remote (LPR on IP) printing from NetWare 5 ❏ When TCP/IP (via EpsonNet Direct Print) printing from Windows 98/95/2000/N

• EpsonNet Internet Print Utility 13-8 Windows NT 4.0 1. Be sure that TCP/IP is correctly installed and setup in the computer and a valid IP address is set for the computer and printer. 2. Be sure that the IPP settings in EpsonNet WebAssist are correctly set. See “IPP” on page 10-27 for instructions on setting up IPP. 3. Click Start , point to Settings ,

• Settings for UNIX 9-3 Setting up for SunSoft Solaris 2.4 or later In the following steps, substitute the name that your printer with the network adapter will be known by for HOSTNAME, and the name by which you want your printer to be known for Rprinter. 1. Add the IP address and printer host name to the \etc\hosts file. For example: 22.33.44.55 HOSTNAME 2. Define th

• Epson C82378, Getting Started 1-5 4. Plug the AC adapter into the network adapter’s DC-IN connector. Be sure to use the AC adapter shipped with this package. w Warning: When you install or uninstall the network adapter, you must turn off the printer and unplug the AC adapter from the wall outlet to prevent electric shock. 5. Plug the power cord into a properly grounded wall outlet. 6. Turn on the printer. 7. The first time you use the network adapter after installing or reinstalling it, turn on the printer while holding down the status sheet button for twenty seconds to initialize the network adapter. Note: After installing the network adapter, some printers take more

• Epson C82378, The EpsonNet Configuration Utility 10-21 AppleTalk Configuration : Items Explanations Printer Name Enter the name of the printer attached to the network adapter. Entity Type Displays the entity type of the printer. Enter EPSONLQ2 to set the entity type for the printer. Zone Name Select the Zone for AppleTalk. Network Number Set Specify the setting method for the AppleTalk network number. Network Number for Manual Mode Enter the network number. Return to Default Resets all configuration settings of the network adapter to the default settings. Send Updates the settings. Cancel Cancel any changes.

• Epson C82378, Settings for NetWare 4-15 7. Make the following settings for Print Queue Configuration. You can select or create a print queue to assign to the network adapter. The following dialog appears when you click Print Queue Configuration . Note: You can make queue settings for a higher context than the context you specified in the NDS Context box. In this case, you must have an ADMIN right for the context in which you set the queue. Queue name: Displays the queue name that is assigned to the network adapter by browsing the queue. Default: the print queue name.OU.O (OU stands for O

• Epson C82378, Setting the IP Address 3-4 5. Click the TCP/IP tab to display the TCP/IP menu. Note: The network administrator must confirm any changes made to the IP address settings. 6. Select the "Get IP address" method, either Auto or Manual . When you select Auto , DHCP becomes available. When you want to set the IP address manually, select Manual . Note: ❏ The default is Auto . When Auto is selected, DHCP is available. To use the DHCP server, it must be installed in your computer and must be correctly configured. See yo

• Epson C82378, Settings for NetWare 4-44 3. Click NetWare under Network on the Configuration menu to view the NetWare setting screen. 4. Choose Enable to use NetWare. Note: If Disable is on, all NetWare related functions stop. Select Disable to avoid being charged for an extra dial-up. 5. Auto is displayed for the Frame Type. 6. Select the Mode. ❏ Select NDS Print Server for NetWare 4.1x or NetWare 5 with NDS mode. ❏ Select Bindery Print Server for NetWare 3.1x, or NetWare 4.1x with Bindery mode. ❏ Select

• Epson C82378, Settings for NetWare 4-45 ❏ Select Standby when not using NetWare, or when problems arise from setting NetWare to Enable. 7. When using NDS mode, enter the NDS Tree name (up to 31 characters) and the NDS Context without "." at the top (up to 255 characters). Leave these items blank if using Remote Printer mode. 8. When you select NDS Print Server or Bindery Print Server for the Mode, make the Print Server settings. Primary File Server Name: Set the file server which the print server logs in (up to 47 characters) if the mode is Bindery Print Server. Print Server Name: Set the print server name (up to 47 characters). Polling Int

• Epson C82378, Troubleshooting 15-5 Problems Specific to Your Network Environment NetWare environment Nothing prints even though clients have sent data to the printer. Cause What to do Clients may not be registered, or the network adapter may not be logged in to the NetWare server. Make sure clients are registered as users of the print queue and the print server. Also, make sure the network adapter is logged in to the NetWare server. If you need more information about Print Server mode or Remote Printer mode, see Chapter 4 or your NetWare manual. EpsonNet WinAssist will not start. Cause What to do Microsoft NetWare Directory Service is installed in your computer. If you are using NDS

Related Products and Documents (Print Server):

Comparable Devices:

Similar Resources:

• Brother MFC-8460N (37 pages) Before you can use the machine, you must set up the hardware and install the software.Please read this “Quick Setup Guide” for the correct setup procedure and installation instructions.Keep this “Quick Setup Guide”, User’s Guide and supplied CD-ROM in a convenient place for quick and easy reference at all times.Step 1Setting Up the machineStep 2Ins …

• NETGEAR WGPS606 (2 pages) WGPS60654 Mbps Wireless Print Serverwith 4-port switchWireless printing for four or more users! Would you and the other users in your network like the freedom to print wirelessly? And, toconnect to more than one printer, without having to add print servers, wireless adapters, orunsightly Ethernet cables? With NETGEAR’s 54 Mbps Wireless Print Server with 4- …

• Oki ML520 (2 pages) There’s nothing like it in its class.The MICROLINE®520/521 is measurablyfaster: it prints faster in any mode, andfeeds paper faster, too. And its printheadis designed to last twice as long as those ofcompetitive dotmatrix printers.It also has some-thing you won’t getwith conventional 9-pin printers: patentedOKISMART Paper HandlingTMfor hassle-free switc …

• EFI Fiery FS150 Pro (156 pages) Fiery FS150 Pro and Fiery FS150 Print Servers Product Guide This document represents the feature set typically included in Fiery® print servers. Actual feature set included may vary by specific Fiery models, as some features may not be supported due to specific project implementation characteristics or regional requirements. For information on a specifi …

• Lantronix xPrintServer (10 pages) 1 BETA USER’S GUIDE: Network Edition “The Plug-and-Print Solution for your iOS® Devices” This Reviewer’s Guide is designed to help you evaluate the Lantronix xPrintServer. ©2011 Lantronix, Inc. All Rights Reserved. Lantronix and xPrintServer are registered trademarks of Lantronix, Inc. iPad, iPhone, iPod, iPod classic, iPod nano, …

• Brother TD4100N (39 pages) NETWORK USER’S GUIDEMulti-Protocol On-board Ethernet Print ServerTD-seriesRead this guide thoroughly before using the machine. Keep the CD-ROM in a convenient place so you can use it quickly if you need to.Visit us at http://solutions.brother.com where you can get product support, the latest driver updates and utilities, and answers to frequently asked que …

Comments, Questions and Opinions: